Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GASOLINE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

Electric Vehicle Charging Stations as a Climate Change Mitigation Strategy

In order to facilitate the use of electric vehicles at NASA Langley Research Center (LaRC), charging stations should be made available to LaRC employees. The implementation of charging stations would decrease the need for gasoline thus decreasing CO2 emissions improving local air quality and providing a cost savings for LaRC employees. A charging station pilot program is described that would install stations as the need increased and also presents a business model that pays for the electricity used and installation at no cost to the government.

Cave, Bridget↗

Cryogenic Orbital Testbed (CRYOTE) Ground Test Article, Final Report

Liquid propulsion has been used since Robert Goddard started developing a liquid oxygen (LO2) and gasoline powered rocket and fired it in 1923 (Ref. 1). In the following decades engineers settled on the combination of liquid hydrogen (LH2) and LO2 as the most efficient propellant combination for in-space travel. Due to their low temperatures (LH2 at 20 K and LO2 at 90 K), they require special handling and procedures. General Dynamics began developing LO2 and LH2 upper stages in 1956 in the form of Centaur, these efforts were soon funded by the Department of Defense in conjunction with NASA (beginning in 1958) (Ref. 2). Meanwhile NASA also worked with McDonnell Douglas to develop the SIV-B stage for the Saturn V rocket. In the subsequent years, the engineers were able to push the Centaur to up to 9 hr of orbital lifetime and the SIV-B to up to 6 hr. Due to venting the resultant boil-off from the high heat loads through the foam insulation on the upper stages, both vehicles remained in a settled configuration throughout the flights, thus the two phases of propellant (liquid and vapor) were separated at a known location. The one exception to this were the Titan/Centaur missions, which thanks to the lower boil-off using three layers of multilayer insulation (MLI), were able to coast unsettled for up to 5.25 hr during direct geosynchronous orbit insertion missions. In the years since there has been a continuous effort to extend the life of these upper stages from hours to days or even months.

Joule-Thompson Effect↗

Personal Rotorcraft Design and Performance with Electric Hybridization

Recent and projected improvements for more or all-electric aviation propulsion systems can enable greater personal mobility, while also reducing environmental impact (noise and emissions). However, all-electric energy storage capability is significantly less than present, hydrocarbon-fueled systems. A system study was performed exploring design and performance assuming hybrid propulsion ranging from traditional hydrocarbon-fueled cycles (gasoline Otto and diesel) to all-electric systems using electric motors generators, with batteries for energy storage and load leveling. Study vehicles were a conventional, single-main rotor (SMR) helicopter and an advanced vertical takeoff and landing (VTOL) aircraft. Vehicle capability was limited to two or three people (including pilot or crew); the design range for the VTOL aircraft was set to 150 miles (about one hour total flight). Search and rescue (SAR), loiter, and cruise-dominated missions were chosen to illustrate each vehicle and degree of hybrid propulsion strengths and weaknesses. The traditional, SMR helicopter is a hover-optimized design; electric hybridization was performed assuming a parallel hybrid approach by varying degree of hybridization. Many of the helicopter hybrid propulsion combinations have some mission capabilities that might be effective for short range or on-demand mobility missions. However, even for 30 year technology electrical components, all hybrid propulsion systems studied result in less available fuel, lower maximum range, and reduced hover and loiter duration than the baseline vehicle. Results for the VTOL aircraft were more encouraging. Series hybrid combinations reflective of near-term systems could improve range and loiter duration by 30. Advanced, higher performing series hybrid combinations could double or almost triple the VTOL aircrafts range and loiter duration. Additional details on the study assumptions and work performed are given, as well as suggestions for future study effort.

electric motors↗

High Pressure Transcritical Combustion (HPTC Combustion)

Combustion is the predominant source of the energy in the US and worldwide, and an overwhelming majority in the transportation sector, particularly liquid hydrocarbons (i.e., gasoline, diesel and jet fuel). Engine manufacturers move to higher operating pressures, above and beyond the critical pressures of the fuel, in order to optimize performance, maximize efficiency and reduce pollutant formation. The design of the next generation of engines, however, are limited by a lack of fundamental understanding of the thermo-physical properties, fluid behavior and chemical kinetics at these high pressures. Terrestrial laboratory studies are hampered by the ubiquitous buoyant flow that renders fundamental experiments difficult and/or impossible to interpret. Studying high pressure transcritical phenomena in microgravity allows researchers to investigate the fundamental aspects of phase change, chemical kinetics and property evaluation in a simplified geometry without the complicating influence of a buoyancy-induced flow.

Combustion↗

On-Orbit Cryogenic Refueling: Potential Mission Benefits, Associated Orbital Mechanics, and Fuel Transfer Thermodynamic Modeling Efforts

The placement of cryogenic fuel/propellant depot stations in Earth orbit has the potential to transform the nature and operations for many types of spaceflight missions. Today, spaceflight missions are almost universally required to carry the entire amount of fuel required for the mission, for the entire duration of the mission, from the point of launch. This is the rough equivalent of making a drive from Ohio to California, requiring the traveler to bring along the total sum of gasoline required for the entire trip, without being able to ‘fill-up’ anywhere along the route. Obviously, this framework of travel greatly encumbers the breadth, scope, and efficiency of potential journeys. Cryogenic fuel/propellant depots have not been implemented because many technical, operational, and engineering challenges still exist. These must be overcome prior to the placement of usable on-orbit propellant depots. This thesis investigates three specific engineering challenges related to on-orbit propellant depots, and presents the current state, technological challenges, and ultimate benefits of on-orbit cryogenic refueling.

No vent fill↗

Diesel Passenger Vehicle Shares Influenced Covid-19 Changes in Urban Nitrogen Dioxide Pollution

Diesel-powered vehicles emit several times more nitrogen oxides than comparable gasoline-powered vehicles, leading to ambient nitrogen dioxide (NO2) pollution and adverse health impacts. The COVID-19 pandemic and ensuing changes in emissions provide a natural experiment to test whether NO2 reductions have been starker in regions of Europe with larger diesel passenger vehicle shares. Here we use a semi-empirical approach that combines in-situ NO2 observations from urban areas and an atmospheric composition model within a machine learning algorithm to estimate business-as-usual NO2 during the first wave of the COVID-19 pandemic in 2020. These estimates account for the moderating influences of meteorology, chemistry, and traffic. Comparing the observed NO2 concentrations against business-as-usual estimates indicates that diesel passenger vehicle shares played a major role in the magnitude of NO2 reductions. European cities with the five largest shares of diesel passenger vehicles experienced NO2 reductions ∼ 2.5 times larger than cities with the five smallest diesel shares. Extending our methods to a cohort of non-European cities reveals that NO2 reductions in these cities were generally smaller than reductions in European cities, which was expected given their small diesel shares. We identify potential factors such as the deterioration of engine controls associated with older diesel vehicles to explain spread in the relationship between cities’ shares of diesel vehicles and changes in NO2 during the pandemic. Our results provide a glimpse of potential NO2 reductions that could accompany future deliberate efforts to phase out or remove passenger vehicles from cities.

Nitrogen Dioxide↗

Flight Performance Estimates for the NASA X-57 Distributed Electric Propulsion Flight Demonstrator

The X-57 flight demonstrator concept featured four configurations starting with a conventional combustion-powered multiengine airplane and ending with a fully electric configuration with two forms of distributed propulsion and a highly modified wing. These configurations, called Mods, were designed to gain incremental insight into different aircraft propulsion configuration options and their impact on the aircraft performance. The gasoline-powered Mod I configuration consumed 2.6 to 2.9 times more stored energy in cruise than the electric but otherwise conventionally configured Mod II configuration. The highly loaded wing of Mod III led to an increase of 40% in the power-off lift-to-drag ratio as compared to Mod II at the project high-speed cruise target speed and altitude. The power-on lift-to-drag ratio of Mod III was 53% higher than Mod II due to the beneficial aero-propulsive interaction of the wingtip-mounted cruise propellers in Mod III. The high-lift propeller system of Mod IV recovered the low-speed performance of the conventional configuration in Mod II that was otherwise lost with the introduction of the highly loaded Mod III wing. The battery-electric configurations also benefitted from a lack of power lapse in the electric motors with increasing air density as compared to the combustion-powered baseline aircraft.

Distributed Performance↗

Flight Performance Estimates for the NASA X-57 Distributed Electric Propulsion Flight Demonstrator

The X-57 flight demonstrator concept featured four configurations starting with a conventional combustion-powered multiengine airplane and ending with a fully electric configuration with two forms of distributed propulsion and a highly modified wing. These configurations, called Mods, were designed to gain incremental insight into different aircraft propulsion configuration options and their impact on the aircraft performance. The gasoline-powered Mod I configuration consumed 2.6 to 2.9 times more stored energy in cruise than the electric but otherwise conventionally configured Mod II configuration. The highly loaded wing of Mod III led to an increase of 40% in the power-off lift-to-drag ratio as compared to Mod II at the project high-speed cruise target speed and altitude. The power-on lift-to-drag ratio of Mod III was 53% higher than Mod II due to the beneficial aero-propulsive interaction of the wingtip-mounted cruise propellers in Mod III. The high-lift propeller system of Mod IV recovered the low-speed performance of the conventional configuration in Mod II that was otherwise lost with the introduction of the highly loaded Mod III wing. The battery-electric configurations also benefitted from a lack of power lapse in the electric motors with increasing air density as compared to the combustion-powered baseline aircraft.

Distributed Performance↗

Catalysts, systems and methods to reduce NOX in an exhaust gas stream

Catalysts, systems and methods are described to reduce NO.sub.x emissions of an internal combustion engine. In one embodiment, an emissions treatment system for an exhaust stream is provided having an SCR catalyst comprising silver tungstate on an alumina support. The emissions treatment system may be used for the treatment of exhaust streams from diesel engines and lean burn gasoline engines. An emissions treatment system may further comprise an injection device operative to dispense a hydrocarbon reducing agent upstream of the catalyst.

Castellano, Christopher R↗

Particles of spilled oil-absorbing carbon in contact with water

Hydrogen generator coupled to or integrated with a fuel cell for portable power applications. Hydrogen is produced via thermocatalytic decomposition (cracking, pyrolysis) of hydrocarbon fuels in oxidant-free environment. The apparatus can utilize a variety of hydrocarbon fuels, including natural gas, propane, gasoline, kerosene, diesel fuel, crude oil (including sulfurous fuels). The hydrogen-rich gas produced is free of carbon oxides or other reactive impurities, so it could be directly fed to any type of a fuel cell. The catalysts for hydrogen production in the apparatus are carbon-based or metal-based materials and doped, if necessary, with a sulfur-capturing agent. Additionally disclosed are two novel processes for the production of two types of carbon filaments, and a novel filamentous carbon product. Carbon particles with surface filaments having a hydrophobic property of oil film absorption, compositions of matter containing those particles, and a system for using the carbon particles for cleaning oil spills.

08 HYDROGEN↗

Ch. 37, Inertial Fusion Energy Technology

Nuclear fission, nuclear fusion, and renewable energy (including biofuels) are the only energy sources capable of satisfying the Earth's need for power for the next century and beyond without the negative environmental impacts of fossil fuels. Substantially increasing the use of nuclear fission and renewable energy now could help reduce dependency on fossil fuels, but nuclear fusion has the potential of becoming the ultimate base-load energy source. Fusion is an attractive fuel source because it is virtually inexhaustible, widely available, and lacks proliferation concerns. It also has a greatly reduced waste impact, and no danger of runaway reactions or meltdowns. The substantial environmental, commercial, and security benefits of fusion continue to motivate the research needed to make fusion power a reality. Replicating the fusion reactions that power the sun and stars to meet Earth's energy needs has been a long-sought scientific and engineering challenge. In fact, this technological challenge is arguably the most difficult ever undertaken. Even after roughly 60 years of worldwide research, much more remains to be learned. the magnitude of the task has caused some to declare that fusion is 20 years away, and always will be. This glib criticism ignores the enormous progress that has occurred during those decades, progress inboth scientific understanding and essential technologies that has enabled experiments producing significant amounts of fusion energy. For example, more than 15 megawatts of fusion power was produced in a pulse of about half a second. Practical fusion power plants will need to produce higher powers averaged over much longer periods of time. In addition, the most efficient experiments to date have required using about 50% more energy than the resulting fusion reaction generated. That is, there was no net energy gain, which is essential if fusion energy is to be a viable source of electricity. The simplest fusion fuels, the heavy isotopes of hydrogen (deuterium and tritium), are derived from water and the metal lithium, a relatively abundant resource. The fuels are virtually inexhaustible and they are available worldwide. Deuterium from one gallon of seawater would provide the equivalent energy of 300 gallons of gasoline, or over a half ton of coal. This energy is released when deuterium and tritium nuclei are fused together to form a helium nucleus and a neutron. The neutron is used to breed tritium from lithium. The energy released is carried by the helium nucleus (3.5 MeV) and the neutron (14 MeV). The energetic helium nucleus heats the fuel, helping to sustain the fusion reaction. Once the helium cools, it is collected and becomes a useful byproduct. A fusion power plant would produce no climate-changing gases.

42 ENGINEERING↗

Tri-City Herald OpEd: Electric Vehicles are a smart choice

Why are so many of us at the Pacific Northwest National Laboratory, a national thought leader in power industry issues located right here in the Tri-Cities, so bullish on the future of EVs? And why do we think it's so important that this country, especially THIS part of the country, be leaders in the adoption of EVs? Is it that we all just happen to like driving polluting golf carts? The answer is that, like most everyone else, most of us here at PNNL drive to work every day, and like most people, we care about the cost of gasoline and the impact that burning imported oil has on the environment and on our foreign policy. The reality is that electric vehicles are simply more efficient, pollute much less, use locally-generated energy, and cost MUCH less to drive.

33 ADVANCED PROPULSION SYSTEMS↗

Deep desulfurization of hydrocarbon fuels

The invention relates to processes for reducing the sulfur content in hydrocarbon fuels such as gasoline, diesel fuel and jet fuel. The invention provides a method and materials for producing ultra low sulfur content transportation fuels for motor vehicles as well as for applications such as fuel cells. The materials and method of the invention may be used at ambient or elevated temperatures and at ambient or elevated pressures without the need for hydrogen.

33 ADVANCED PROPULSION SYSTEMS↗

Decision Analysis Tool to Compare Energy Pathways for Transportation

With the goals of reducing greenhouse gas emissions, oil imports, and energy costs, a wide variety of automotive technologies are proposed to replace the traditional gasoline-powered internal combustion engine (g-ICE). A prototype model, Analytica Transportation Energy Analysis Model (ATEAM), has been developed using the Analytica decision modeling environment, visualizing the structure as a hierarchy of influence diagrams. The report summarized the FY2010 ATEAM accomplishments.

33 ADVANCED PROPULSION SYSTEMS↗

Catalytic conversion of cellulose to liquid hydrocarbon fuels by progressive removal of oxygen to facilitate separation processes and achieve high selectivities

Described is a method to make liquid chemicals, such as functional intermediates, solvents, and liquid fuels from biomass-derived cellulose. The method is cascading; the product stream from an upstream reaction can be used as the feedstock in the next downstream reaction. The method includes the steps of deconstructing cellulose to yield a product mixture comprising levulinic acid and formic acid, converting the levulinic acid to .gamma.-valerolactone, and converting the .gamma.-valerolactone to pentanoic acid. Alternatively, the .gamma.-valerolactone can be converted to a mixture of n-butenes. The pentanoic acid so formed can be further reacted to yield a host of valuable products. For example, the pentanoic acid can be decarboxylated yield 1-butene or ketonized to yield 5-nonanone. The 5-nonanone can be hydrodeoxygenated to yield nonane, or 5-nonanone can be reduced to yield 5-nonanol. The 5-nonanol can be dehydrated to yield nonene, which can be dimerized to yield a mixture of C.sub.9 and C.sub.18 olefins, which can be hydrogenated to yield a mixture of alkanes. Alternatively, the nonene may be isomerized to yield a mixture of branched olefins, which can be hydrogenated to yield a mixture of branched alkanes. The mixture of n-butenes formed from .gamma.-valerolactone can also be subjected to isomerization and oligomerization to yield olefins in the gasoline, jet and Diesel fuel ranges.

09 BIOMASS FUELS↗

Some recent efforts in chemical hydrogen storage at Loa Alamos

Within the transportation sector, a necessity towards realizing the use of hydrogen (H{sub 2}) as an alternative fuel, is its storage for controlled delivery. The U.S. DOE's Centers of Excellence (CoE) in H{sub 2} storage have pursued different methodologies (metal hydrides, chemical hydrides, and sorbents), for the express purpose of supplanting gasoline's current > 300 mile driving range. Chemical H{sub 2} storage has been dominated by one material, ammonia borane (H3B-NH3, AB), due to its high gravimetric capacity of H{sub 2} (19.6 wt %) and low molecular weight (30.7 g mol{sup -1} ). As such, a number of publications have described H{sub 2} release from amine boranes, yielding various rates depending on the method applied. The viability of any storage system is also dependent on efficient recyclability. Within our CoE we have thus endeavored to find efficient base-metal catalyzed AB dehydrogenation pathways and regeneration schemes for the spent fuel from H{sub 2} depleted AB. We will present some recent results in these areas in this vein.

08 HYDROGEN↗

Seven Traffic Signals in Two Minutes

Topeka, KS has activated the first of three key traffic corridors to receive a "green light tunnel" a real-time adaptive traffic signal system that synchronizes signals to create a series of green lights for motorists. The result is fewer stops, less travel time and -- most importantly -- a lot of saved gasoline.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Breakthrough: Using Microbes to Make Advanced Biofuels

Jay Keasling, Berkeley Lab's Associate Director for Bioscience and the CEO of DOE's Joint BioEnergy Institute (JBEI), explains how special strains of microbes can convert the biomass of non-food crops and agricultural waste into fuels for cars, trucks and jet planes. Keasling's research team at JBEI has developed E.coli that can digest switchgrass and convert the plant sugars into gasoline, diesel or jet fuel, not unlike the process by which beer is brewed.

09 BIOMASS FUELS↗