Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dislocation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

EBSD analysis of surface and bulk microstructure evolution during interrupted tensile testing of a Fe-19Cr-12Ni alloy

Highlights: • Similar deformation structures are obtained for surface and bulk grains. • A lower strain is needed for twinning in surface grains than in bulk grains. • A reduced ability to cross-slip due to low SFE leads to an increasing LAB density. • Twinning reduces the dislocation slip length. • High strain-hardening rate is maintained up to high strains. - Abstract: The microstructure evolution in both surface and bulk grains in a pure Fe-19Cr-12Ni alloy has been analyzed using electron backscatter diffraction after tensile testing interrupted at different strains. Surface grains were studied during in situ tensile testing performed in a scanning electron microscope, whereas bulk grains were studied after conventional tensile testing. The evolution of the deformation structure in surface and bulk grains displays a strong resemblance but the strain needed to obtain a similar deformation structure is lower in the case of surface grains. Both slip and twinning are observed to be important deformation mechanisms, whereas deformation-induced martensite formation is of minor importance. Since the stacking fault energy (SFE) is low, ~17 mJ/m{sup 2}, dynamic recovery by cross slip of un-dissociated dislocations is unfavorable. This reduces the annihilation of dislocations which in turn leads to a significant increase of low angle boundaries with increasing strain. The low SFE also favors formation of deformation twins which reduces the slip distance, leading to a hardening similar to the Hall-Petch relation. The combination of a low ability for cross-slip and a reduced slip distance caused by twinning is concluded to be the main reason for maintaining a high strain-hardening rate up to strains close to necking.

36 MATERIALS SCIENCE↗

Lattice rotations in precipitate free zones in an Al-Mg-Si alloy

Highlights: • Recovery processes in precipitate free zones differ from those in grain interiors. • Most precipitate free zones contain few dislocations, after deformation. • Deformation can induce large misorientations in precipitate free zones. • Some deformed precipitate free zones contain nanoscale grains. - Abstract: Scanning precession electron diffraction and automated crystal orientation mapping in a transmission electron microscope (TEM) have been applied to quantitatively study the crystal orientation of precipitate free zones (PFZs) of four GB regions in an AA6060 alloy in peak aged condition (temper T6) after uniaxial compression to 20% engineering strain. The PFZ width in the alloy was found to be w = 170 ± 40 nm. The results show that some PFZs develop significant misorientations relative to their parent grain, and represent, to the best knowledge of the authors, the first quantitative evidence of this. This misorientation may either be constant inside a particular PFZ, making it appear like a band or a very elongated subgrain, or be partitioned in discrete regions with a diameter comparable to the PFZ width, making the former PFZ into a collection of small grains. The band-like PFZ observed in this work had a misorientation relative to its parent grain of ≈ 7°, while the grain-like PFZ had grains with misorientations between ≈ 12° and ≈ 20° relative to its parent grain. The other PFZs that were observed had only limited misorientations relative to their parent grains, and had either dislocations perpendicular to the GB plane or a dislocation wall at the transition region. A general TEM study of the material at various engineering strains was also conducted and suggests that grain-like PFZs are more frequent for larger strains, indicating that the different PFZ features are likely due to different strain localisation in individual PFZs. This localisation is expected to be influenced by the orientation of the loading axis relative to crystal orientations and GB planes. It is also suggested that the different PFZ features engender different work hardening rates and possibly affect nucleation of intergranular fracture. The results support previous studies on the microstructure evolution of PFZs in age-hardenable aluminium alloys during deformation.

36 MATERIALS SCIENCE↗

Correlation between microstructures and mechanical properties of cryorolled CuNiSi alloys with Cr and Zr alloying

Highlights: • Annihilation of dislocations was suppressed by Cr alloying to CuNiSi alloys. • Cr alloying to CuNiSi alloys hinders the kinetics and refines precipitates. • Zr alloying to CuNiSi alloys promotes the growth and kinetics of precipitates. • The mechanical properties were quantitatively related to the microstructures. - Abstract: Due to their high strength and high electrical conductivity, CuNiSi system alloys are widely used as lead frames and connectors. In this work, CuNiSi alloys alloyed with Cr and Zr were rolled at liquid nitrogen temperature and subjected to various aging treatments. High-angle annular dark field scanning transmission electron microscopy (HAADF-STEM) analysis showed that in addition to forming Cr{sub 3}Si and Ni{sub 2}SiZr particles, elemental Cr and Zr distributed evenly in the matrix. Ni and Si segregated at the interface between the particles and matrix to form Ni{sub 2}Si precipitates. During the aging process, Cr alloying increased the hardness while slightly reducing the electrical conductivity of the alloy. This was ascribed to the refined precipitates and hindered precipitation kinetics. Zr alloying promoted both the precipitate growth and the precipitation kinetics of the CuNiSi alloys, while decreasing their hardness and enhancing their electrical conductivity. According to the results of the synchrotron X-ray diffraction (XRD) analysis, Cr alloying increased the dislocation density of CuNiSi alloys and suppressed the annihilation of dislocations during aging. This promoted strength through work hardening. Compared to CuNiSi alloys aged at 723 K for 2 h, the ultimate tensile strength of the alloys obtained after Cr alloying using a two-step rolling aging process was increased by 154 MPa and their electrical conductivity was increased by 4.8% International Annealed Copper Standard (IACS).

36 MATERIALS SCIENCE↗

The influence of power spinning and annealing temperature on microstructures and properties of Cu-Sn alloy

Highlights: • The strengthening effect of power spinning is mainly achieved by strengthening fine grains and dislocations. • Twins formed by the aggregation and overlapping of stacking faults grow and widen • In power spinning of Cu-Sn alloy, plastic deformation is primarily powered by dislocation sliding. - Abstract: Electron back scatter diffraction pattern (EBSD), metallographic microscope (OM) and transmission electron microscope (TEM) are used to analyze the microstructural state of the Cu-Sn alloy before and after power spinning and annealing. The results show that after power spinning, the α phase grains are refined and gradually evolve into small and fine α{sub II} and deformed α{sub III} crystal grains, with an average grain size of about 2.2 μm. Work hardening results in massive network-like subgrain boundaries distributed in power spinning microstructure. Annealing at 400 °C contributes to the formation of dislocation cells and stacking faults, and high-angle grain boundaries (HABS) start to migrate and slide. After the formation of less defective equiaxed grains at 500 °C, twins continue to grow and widen based through continuous accumulation of stacking faults. Further testing of mechanical properties reveals that power spinning is conducive to the improvement of mechanical properties of Cu-Sn alloy.

36 MATERIALS SCIENCE↗

Toughening mechanism of inter-critical heat-affected zone in a 690 MPa grade rack plate steel

Highlights: • Relationship between toughness and microstructure was confirmed. • The toughness of ICHAZ is higher than that of FGHAZ. • Fine bainitic microstructure in ICHAZ plays an important role on improving toughness. • The homogeneous distribution of dislocation and local strain facilitate the plastic deformation prior fracture. - Abstract: The inter-critical heat-affected zone (ICHAZ) and fine grain heat-affected zone (FGHAZ) of a 690 MPa grade rack plate steel were simulated by Gleeble3500 simulator. The toughening mechanism of ICHAZ was clarified by analyzing microstructural characteristics and instrumental Charpy impact tests. The study showed that the ICHAZ had higher toughness than FGHAZ. And the microstructure in FGHAZ was martensite, while bainitic microstructure was obtained in ICHAZ. Both the prior austenite grain size and effective grain size of ICHAZ were smaller than that of FGHAZ, which played an important role in improving the toughness of ICHAZ. It was found that the extensive plastic deformation prior fracture in ICHAZ could consume large energy during crack initiation and propagation. The large plastic deformation capacity of ICHAZ was related to the large fraction of large-angle boundaries and low dislocation density, as well as the homogeneous distribution of local strain and geometrically necessary dislocations.

36 MATERIALS SCIENCE↗

Advanced processing of EBSD data to distinguish the complex microstructure evolution of a Cu-Ni-Si alloy induced by fatigue

Highlights: • Microstructure investigation of the fatigue behaviour of a Cu-Ni-Si alloy • Use of ECCI and EBSD to investigate the microstructure evolution related to fatigue dislocations structures • Characterisation of local plastic accommodation through EBSD misorientation criteria - Abstract: The present work aims at identifying the evolution of the microstructure of a Cu-Ni-Si (Corson alloy) alloy after low cycle fatigue by means of advanced electron microscopy analysis techniques (SEM-ECCI, Orientation Imaging Microscopy by means of SEM-EBSD and TEM). Deep attention is paid on the material subjected to high cyclic strains where a transient cellular dislocation structure transformed into precipitate free bands. It is shown that the formation of dislocation cells leads to a high GROD and high GOSaera value and its standard deviation. However, the presence of precipitate free bands results in the low GOSarea level and its low standard deviation.

36 MATERIALS SCIENCE↗

Study on the creep deformation behavior and characterization of 9Cr-1Mo-V-Nb steel at elevated temperatures

Highlights: • The true creep deformation mechanism has been found by an evaluation of threshold stresses. • The analysed creep data suggest that the rate-controlling mechanism of creep is dislocation climb. • Coarsening of the M{sub 23}C{sub 6} carbides has been observed at 650 °C and 700 °C during creep. In this study, creep tests were conducted on a set of specimens made from the same tube of T91 steel at different temperatures (600 °C, 650 °C and 700 °C) with the applied stresses ranging from 30 MPa to 180 MPa and rupture times from 28.7 to 7957 h for understanding the creep mechanism. The stress dependence of minimum creep rates exhibits a power law with different exponents were found to be 14.3, 11 and 4.6 at 600 °C, 650 °C and 700 °C, respectively. Activation energy of creep was determined to be ~573 kJ/mol, which is ~53% higher than that of the lattice self-diffusion in α-iron. Based on the stress exponents, the modified Bird-Murkherjee-Dorn (BMD) equation was used to find the threshold stresses which has shown the strongly dependent on the test temperature. After incorporating the threshold stress, true activation energy of creep was found to be decreased ~271 kJ/mol, which is equivalent to that of lattice-self diffusion in α-iron. This subsequently led to evaluation of true stress exponent ~4. The results of creep data suggest that the rate-controlling mechanism of creep is dislocation climb for T91 steel. Microstructural observation of T91 steel is mainly consisting of lath martensite structure with fine MX carbonitrides and M{sub 23}C{sub 6} carbides were characterized using the scanning and transmission electron microscopes. The stress dependence of creep rupture life has shown that the operating mechanism of creep is similar. Furthermore, creep data was analysed for validity of the Monkman-Grant relationship and creep damage tolerance parameter. The qualitative microstructure of the crept samples show that less number of MX carbonitrides within grains is responsible for creep cavity formation and decreasing the rupture life. Thus, microstructural degradation is attributed to M{sub 23}C{sub 6} carbides coarsened and dislocation sub-structure boundaries are mainly responsible for creep damage. The fracture morphology of the samples has revealed with dimples is a typical transgranular ductile failure.

36 MATERIALS SCIENCE↗

Quantification of room temperature strengthening of laser shock peened Ni-based superalloy using synchrotron microdiffraction

Laser shock peening (LSP), a surface modification technique, is promising to enhance the strength and wear resistance for Ni-based superalloys. To understand the strengthening mechanism in a laser shock peened Ni-based superalloy DZ417G, we utilize synchrotron poly- and monochromatic X-ray microdiffraction, as well as electron microscopy and microhardness to quantify the local microstructures and mechanical properties at various depths. In the 1.2-mm-deep hardened layer, the microhardness increases monotonically by ~50% from the unaffected interior to the surface. Quantitative microdiffraction analysis shows that large amounts of dislocations are introduced by LSP. High densities of 7.1 × 10 15 m -2 and 11.8 × 10 15 m -2 are seen close to the peened surface for the γ- and γ'-phases, respectively, which are 5 and 20 times of those in the unaffected region. Different gradients of dislocation density are observed for the two phases from interior to surface, and their combined effect accounts well for the hardness increment. Due to the unaltered γ'-precipitates and chemical composition in the LSP affected zone, the large density of dislocations dominates the observed strengthening. Combined poly- and monochromatic X-ray microdiffraction allows quantifying the local microstructures of plastic deformation over a large sampling scale that can hardly be achieved using other materials characterization techniques.

36 MATERIALS SCIENCE↗

In-situ single-grain peak profile measurements on Ti-7Al during tensile deformation.

High-energy three-dimensional X-ray diffraction with medium and high reciprocal space resolution was applied to study in situ tensile deformation of Ti-7Al specimens. Samples with planar and random dislocation microstructures were prepared and characterized by electron microscopy. Stress tensors of individual grains were obtained at several loads up to 2% deformation. The stress tensors were found to rotate, and resolved shear stresses were calculated. High-resolution reciprocal space maps of selected grains were recorded. Azimuthal and radial distributions were visualized and discussed in terms of idealized dislocation structures. Heterogeneous grain rotations were observed for the planar microstructure and found to be consistent with activation of the highest stressed basal slip system. Intra-granular strain gradients were detected in excess of the intrinsic radial dislocation peak broadening. The potential of combining the applied techniques with modeling to obtain multiple length-scale information during deformation of bulk specimens is discussed.

36 MATERIALS SCIENCE↗

On deformation twinning in a 17.5%Mn-TWIP steel: A physically-based phenomenological model

TWinning Induced Plasticity (TWIP) steel is a typical representative of the 2nd generation of advanced high strength steel (AHSS) which exhibits a combination of high strength and excellent ductility due to the twinning mechanisms. This paper discusses the principal features of deformation twinning in faced-centered cubic austenitic steels and shows how a physiscally-based macroscopic model can be derived from microscopic considerations. In fact, a dislocation-based phenomenological model, with internal state variables such as dislocation density and micro-twins volume fraction representing the microstructure evolution during deformation process, is proposed to describe the deformation behavior of TWIP steels. The contribution of this work is the incorporation of a physically-based twin’s nucleation and volume fraction evolution model in a conventional dislocation-based approach. Microstructural level investigations, using scanning electron microscope (SEM) and transmission electron microscope (TEM) techniques, for the TWIP steel Fe–17.5 wt.% Mn–1.4 wt.% Al- 0.56 wt.% C, are used to validate and verify modeling assumptions. The model could be regarded as a semi-phenomenological approach with sufficient links between microstructure and overall properties and therefore offers good predictive capabilities. Its simplicity also allows a modular implementation in finite element-based metal forming simulations.

36 MATERIALS SCIENCE↗

Hydrostatic pressure effect on mechanical behavior and texture evolution of Al and Brass

The effect of hydrostatic pressure on shear strength and microstructural evolution of polycrystalline FCC metals was investigated. Hydrostatic pressure of up to 5 GPa was imposed on commercial purity aluminum and 70/30 brass samples using a modified opposed-anvil apparatus (tri-anvil) that allows for measurement of shear strength in thin foil specimens. Similar to the previous investigations made in BCC metals (Ta and Mo), the shear strength of FCC metals increases significantly as the pressure rises. At 5 GPa, the shear strength of aluminum increased to 8 times its value at atmospheric pressure and 70/30 brass increased by a factor of 2.7. Here, EBSD analysis reveals an evident accumulation of dislocations in all sheared samples, with an approximately 50% decrease in grain diameter. Texture analysis suggests that, in addition to helping form selectively oriented dislocation walls, hydrostatic pressure also serves as a threshold to select certain favorable orientations in sheared metals. We propose that these hydrostatic pressure effects are intrinsically due to the excess volume associated with the cylindrical strain field of dislocation lines.

36 MATERIALS SCIENCE↗

Formation of large loop-hydrogen complexes and related effects on mechanical properties of Zirconium investigated with molecular dynamics method

Here, using molecular dynamics (MD) method, interaction between hydrogen (H) atoms and interstitial or vacancy dislocation loops in Zr is extensively studied. The results show that the binding of hydrogen atoms to dislocation loops is anisotropic (attractive or repulsive), depending on the position of the hydrogen atoms with respect to the loop’s core. The anisotropy is governed by excess volume and stress field induced by the loop. For a 1/3[$2\bar1$$\bar1$$0$] interstitial dislocation loop, hydrogen atoms preferentially segregate near the outside of the loop and close to the decomposition knots of the loop. While for a 1/3[$2\bar1$$\bar1$$0$] or 1/6[$20$$\bar2$$3$] vacancy loop, hydrogen atoms prefer to segregate near the inside of the loop. The present work indicates large loop-hydrogen complexes could form in Zr. The binding of hydrogen to loops is stable up to 600 K, while dissociation is observed at 900 K. Formation of loop-hydrogen complexes affect the activation of slip system, resulting in higher yield stress of Zr. The effect increases with the increasing ratio of H to vacancies or interstitials in the vacancy or interstitial loops. The results imply the effects of large loop-hydrogen complexes should be considered to fully understand radiation damage in Zr.

36 MATERIALS SCIENCE↗

In-situ TEM study of microstructural evolution in NFA and Cr 3 C 2 @SiC-NFA composite during ion irradiation

In this article, the ion irradiation responses of a Fe-based nanostructured ferritic alloy or ‘NFA’ (Fe–9Cr–2W–0.2V–0.4Ti–0.3Y 2 O 3 ) and a Cr 3 C 2 @SiC-NFA composite were assessed. In-situ ion irradiation with TEM observation was carried out by using 1 MeV Kr ++ ions at doses of 0, 1, 3, 5, 10 dpa and temperatures of 300 °C and 450 °C. Both the NFA and Cr 3 C 2 @SiC-NFA samples showed significant dislocation density after 10 dpa at 300 °C. However, the Cr 3 C 2 @SiC-NFA composite showed a significantly lower dislocation loop density and a smaller average loop size during the irradiation at 450 °C as opposed to the NFA. At 300 °C, 1/2<111> type dislocation loops were observed in both the NFA and Cr 3 C 2 @SiC-NFA samples. Interestingly, at 450 °C, <100> type loops were dominant in the NFA sample while 1/2<111> type loops were still dominant in the Cr 3 C 2 @SiC-NFA sample. The results were discussed based on the large surface sink effects and enhanced interstitial-vacancy recombination at higher temperatures. Lastly, the additional Si element in the Cr 3 C 2 @SiC-NFA sample might have played a significant role in determining the dominant loop types.

36 MATERIALS SCIENCE↗

Radiation response of a Fe–20Cr–25Ni austenitic stainless steel under Fe 2+ irradiation at 500 °C

The radiation response of a Fe–20Cr–25Ni austenitic stainless steel under self-ion irradiation at 500 °C was systematically investigated. The steel was irradiated at 500 °C by 3.5 MeV Fe 2+ ions to 10, 50, and 150 peak dpa, respectively. In the 200–400 nm depth region, radiation-induced Frank loops were relatively stable in both size and number density from 10 to 150 peak dpa. Anisotropic distribution of Frank loops was observed in the 50 and 150 peak dpa specimens, possibly due to interaction of Frank loops and network dislocations with preferred orientations. Coarse voids were found only in the 50 and 150 peak dpa specimens in depths less than 750 nm, suggesting that injected interstitials at deeper regions suppressed the void nucleation. The peak swelling was very low (~0.4%) for both 50 and 150 peak dpa irradiation. Radiation also led to the formation of intragranular plate-like Cr-rich carbides. Radiation-induced segregation of Ni and Si was found at various sinks: dislocation loops, void surfaces, and carbide-matrix interfaces. Finally, irradiation hardening was measured by nanoindentation and the results are consistent with microstructure-based calculations using the dispersed barrier hardening model. The major contributor to irradiation hardening changed from Frank loops at the lowest dose to network dislocations at the highest dose.

dislocation loops↗

Defect studies in ion irradiated AlGaN

Defects created in Al0.4Ga0.6N crystals by 320 keV Ar ion irradiation were studied by using RBS/C and TEM techniques. One of the main aims of the work was to use a new version of McChasy, a Monte – Carlo simulation code of backscattering spectra, for the analysis of experimental results obtained for a dislocations-containing crystal. Transmission Electron Microscopy technique was used to get a better insight into dislocation and dislocation loop geometries in order to restrict the range of parameters used in simulations. RBS/C analysis was performed in a 1.5 MeV – 3 MeV energy range in order to check if MC simulations correctly reproduce backscattering spectra at different energies.

36 MATERIALS SCIENCE↗

Orientation influence on grain size-effects in ultrafine-grained magnesium

The mechanical behavior of ultrafine-grained magnesium was studied by discrete dislocation dynamics (DDD) simulations. Our results show basal slip yields a strong size effect, while prismatic and pyramidal slips produce a weak one. We developed a new size-strength model that considers dislocation transmission across grain boundaries. Good agreement between this model, current DDD simulations and previous experiments is observed. These results reveal that the grain size effect depends on 3 factors: Peierls stress, dislocation source strength and grain boundary strength.

36 MATERIALS SCIENCE↗

Characterizing defect structures in AM steel using direct electron detection EBSD

The mechanical properties of additive and traditionally manufactured alloys are largely dependent on the characteristics and distribution of dislocation cell networks that develop during the fabrication process. This work demonstrates the ability to quantitatively characterize these dislocation structures by high angular resolution electron backscatter diffraction analysis using a direct electron detector. The defect structures are characterized in terms of the geometrically necessary dislocation density and the associated Burgers vector and line direction. Furthermore, the results are discussed in terms of potential defect formation mechanisms.

36 MATERIALS SCIENCE↗

Origin of strain softening in a nanograined Al alloy

Here, one-step and multi-step nanoindentation experiments were conducted to investigate the mechanical response of an Al-Mg-Li alloy. Opposite to the strain hardening effect observed in the coarse-grained (CG) alloy, the nanograined (NG) alloy exhibits strain softening. Compared with multi-step nanoindentation experiments, the ultralow dislocation density and the grain boundary (GB) segregation promote a higher stress level during one-step nanoindentation experiments. Residual perfect dislocations induced by a previous loading and unloading during multi-step nanoindentation experiments lower the stress required for further plastic deformation. In addition, the storage of partial dislocations also serves to render plastic flow to commence at lower stresses. This work provides new insights for the fabrication and property optimization of NG alloys.

36 MATERIALS SCIENCE↗