Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Correlation coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

Characteristics of Perforated Diffusers at Free-stream Mach Number 1.90

An investigation was conducted at Mach number 1.90 to determine pressure recovery and mass-flow characteristics of series of perforated convergent-divergent supersonic diffusers. Pressure recoveries as high as 96 percent were obtained, but at reduced mass flows through the diffuser. Theoretical considerations of effect of perforation distribution on shock stability in converging section of diffuser are presented and correlated with experimental data. A method of estimating relative importance of pressure recovery and mass flow on internal thrust coefficient basis is given and a comparison of various diffusers investigated is made.

FLOW, SUPERSONIC↗

Calibration of Direct Velocimetry Using Hot Wire Anemometry

We studied the functionality of the IFA300 Hot Wire Anemometry system and its feasibility for the calibration of Direct Estimator Velocimetry (DEV) using Laser Induced Florescence (LIF). The experimental setup consisted of a single-wire hot wire probe measuring one component of velocity, the anemometry computational hardware and software, an HP oscilloscope, and a table fan to produce a simple flow with fluctuations. Measurements were taken at several points in the stream wise and transverse directions in the flow and various parameters recorded such as mean velocities temperature, turbulence intensities, skewness coefficients and flatness coefficients. The IFA300 software also allowed us to perform statistical manipulations such as spectrum analysis on velocities samples and correlation. Utilization of data files, also produced by the anemometry software, and post analysis were performed to produce graphical representations of turbulent intensity versus probe position and a flow field velocity profile. We concluded that the IFA300 Hot Wire Anemometry system is a reliable and functional method for calibration of DEV using LIF. Our future intentions are to set up a test chamber such that both velocity measurement techniques can be applied simultaneously, thus the calibration.

Holland, Michael L.↗

Cepheid Calibration of the Peak Brightness of SNe Ia.: SN 1989B in NGC 3627 - 9

Repeated imaging observations have been made of NGC 3627 with the Hubble Space Telescope in 1997/98, over an interval of 58 days. Images were obtained on 12 epochs in the F555W band and on five epochs in the F8141,V band. The galaxy hosted the prototypical, "Branch normal", type la supernova SN 1989B. A total of 83 variables have been found, of which 68 are definite Cepheid variables with periods ranging from 75 days to 3.85 days. The de-reddened distance modulus is determined to be (m - M)(sub 0) = 30.22 +/- 0.12 (internal uncertainty) using a subset of the Cepheid data whose reddening and error parameters are secure. The photometric data of Wells et al. (1994), combined with the Cepheid data for NGC 3627 give MB(max) = -19.36 +/- 0.18 and M(sub V)(max) = -19.34 +/- 0.16 for SN 1989B. Combined with the previous six calibrations in this program, plus two additional calibrations determined by others gives the mean absolute magnitudes at maximum of (M(sub B)) = -19.48 +/- 0.07 for "Brunch normal" SNe Ia at this interim stage in the calibration program. Using the argument by Wells et al. (1994) that SN 1989B here is virtually identical in decay rate and colors at maximum with SN 198ON in NGC 1316 in the Fornax cluster, and that such identity means nearly identical absolute magnitude, it follows that the difference in the distance modulus of NGC 3627 and NGC 1316 is 1.62 +/- 0.03 mag. Thus the NGC 3627 modulus implies that (m - M)(sub 0) = 31.84 for NGC 1316. The second parameter correlations of M(max) of blue SNe la with decay rate, color at maximum, and Hubble type are re-investigated. The dependence of (M(max)) on decay rate is non-linear, showing a minimum for decay rates between 1.0 less than ADelta(sub m)15 less than 1.6. Magnitudes corrected for decay rate show no dependence on Hubble type, but a dependence on color remains. Correcting both the fiducial sample of 34 SNe la with decay-rate data and the current eight calibrating SNe la for the correlation with decay rate as well as color gives H(sub 0) = 60 +/- 2 (internal) km/s Mpc, in both B and V. The same value to within 4% is obtained if only the SNe la in spirals (without second parameter corrections) are considered. The correlation of SNe la color at maximum with M(max) cannot be due to internal absorption because the slope coefficients in B, V, and I with the change in magnitude are far from or even opposite to the canonical reddening values. The color effect must be intrinsic to the supernova physics. "Absorption" corrections of distant blue SNe la will lead to incorrect values of H(sub 0). The Cepheid distances used in this series are insensitive to metallicity differences. The zeropoint of the P-L relation is based on an assumed LMC modulus of (m - M)(sub 0) = 18.50. As this may have to be increased by 0(sup m).06 to 0(sup m).08, all distances in this paper will follow and Ho will decrease by 3 - 4%.

Saha, A.↗

Ultrasonic wave propagation in trabecular bone predicted by the stratified model

The objective of this study was to investigate ultrasound propagation in trabecular bone by considering the wave reflection and transmission in a multilayered medium. The use of ultrasound to identify those at risk of osteoporosis is a promising diagnostic method providing a measure of bone mineral density (BMD). A stratified model was proposed to study the effect of transmission and reflection of ultrasound wave within the trabecular architecture on the relationship between ultrasound and BMD. The results demonstrated that ultrasound velocity in trabecular bone was highly correlated with the bone apparent density (r=0.97). Moreover, a consistent pattern of the frequency dependence of ultrasound attenuation coefficient has been observed between simulation using this model and experimental measurement of trabecular bone. The normalized broadband ultrasound attenuation (nBUA) derived from the simulation results revealed that nBUA was nonlinear with respect to trabecular porosity and BMD. The curve of the relationship between nBUA and BMD was parabolic in shape, and the peak magnitude of nBUA was observed at approximately 60% of bone porosity. These results agreed with the published experimental data and demonstrated that according to the stratified model, reflection and transmission were important factors in the ultrasonic propagation through the trabecular bone.

Non-NASA Center↗

Part 2 of a Computational Study of a Drop-Laden Mixing Layer

This second of three reports on a computational study of a mixing layer laden with evaporating liquid drops presents the evaluation of Large Eddy Simulation (LES) models. The LES models were evaluated on an existing database that had been generated using Direct Numerical Simulation (DNS). The DNS method and the database are described in the first report of this series, Part 1 of a Computational Study of a Drop-Laden Mixing Layer (NPO-30719), NASA Tech Briefs, Vol. 28, No.7 (July 2004), page 59. The LES equations, which are derived by applying a spatial filter to the DNS set, govern the evolution of the larger scales of the flow and can therefore be solved on a coarser grid. Consistent with the reduction in grid points, the DNS drops would be represented by fewer drops, called computational drops in the LES context. The LES equations contain terms that cannot be directly computed on the coarser grid and that must instead be modeled. Two types of models are necessary: (1) those for the filtered source terms representing the effects of drops on the filtered flow field and (2) those for the sub-grid scale (SGS) fluxes arising from filtering the convective terms in the DNS equations. All of the filtered-sourceterm models that were developed were found to overestimate the filtered source terms. For modeling the SGS fluxes, constant-coefficient Smagorinsky, gradient, and scale-similarity models were assessed and calibrated on the DNS database. The Smagorinsky model correlated poorly with the SGS fluxes, whereas the gradient and scale-similarity models were well correlated with the SGS quantities that they represented.

Okongo, Nora↗

Additional Characterization of Sonoran Pics in Support of A Stable Multi-Sensor Geostationary Imager Record

The Sonoran Desert is the most utilized Pseudo Invariant Calibration Site (PICS) located in the Americas for post-launch radiometer drift monitoring and sensor pair radiometric scaling. The Sonoran Desert is located near the US Arizona and Mexican border with an elevation of 37 m. The site has small spatial and angular variations; however, soil moisture can cause short- term periodic reflectance fluctuations. The NASA Clouds and the Earth’s Radiant Energy System (CERES) project utilizes the site to validate the GOES East and West imager calibration coefficients derived from inter-calibrating GOES with MODIS. Because the daily local noon angular solar and viewing angles repeat every year over the site, a daily exoatmospheric radiance model (DERM) can be constructed over the lifetime of a well-calibrated GOES sensor. DERM based on a well-calibrated GOES imager can then be used to determine the calibration coefficients of successive GOES imagers to provide a stable multi-sensor GOES imager record. This will ensure that the GOES retrieved clouds and derived broadband fluxes can be used to infer the regional diurnal cycle in between Terra and Aqua CERES measurements to accurately compute the daily mean regional fluxes and clouds over the 20-year CERES SYN1deg product. Although the Sonoran Desert surface reflectance and atmospheric column vary seasonally, the inter-annual variability of the seasonal cycle is small, but it adds noise to the resulting DERM calibration coefficients. We seek to reduce the uncertainty of the DERM approach by improving the clear-sky filtering and correlating the observed interannual reflectance variability with atmospheric parameters, such as precipitable water, ozone concentration, and aerosol optical depth. The additional characterization of the Sonoran Desert site DERM for both the GOES East and West positions should improve the accuracy of the CERES SYN1deg product clouds and fluxes.

Prathana Khakurel↗

Dispersion of surface-modified, aggregated, fumed silica in polymer nanocomposites

Surface modification of model silica to enhance compatibility in nanocomposites has been widely studied. In addition to model spherical silica, several authors have investigated the impact of surface conditions on compatibility in commercial aggregated carbon black and silica. Here, dispersion is investigated for a series of nanocomposites produced from commercially modified fumed silica mixed with styrene butadiene rubber, polystyrene, and polydimethylsiloxane. Surface modification includes variation in surface hydroxyl content, siloxane, and silane treatment. Qualitatively, hydroxyl groups on the silica surface are considered incompatible with non-polar polymers, while methyl groups are compatible with oleophilic polymers. X-ray scattering was used to analyze the filler aggregate structure before and after dispersion, and the second virial coefficient was used to quantify nanodispersion. The content of surface moieties was determined from Fourier-transform infrared spectroscopy. It is observed that modified silica can display mean field or specific interactions as reflected by the presence of a correlation peak in x-ray scattering. For systems with specific interactions, a critical ordering concentration is observed related to the free energy change for structuring. A van der Waals model was used to model the second virial coefficient as a function of accumulated strain, yielding the excluded volume and an energetic term. The excluded volume could be predicted from the structural information, and the bound polymer layer was directly related to the surface methyl content, whereas the energetic term was found to synergistically depend on both the methyl and hydroxyl surface content.

36 MATERIALS SCIENCE↗

Quantitative study of the effect of grain boundary parameters on the slip system level Hall-Petch slope for basal slip system in Mg-4Al

Several theoretical studies have reported that the geometry and structure of grain boundaries in polycrystalline materials could impose a significant effect on the Hall-Petch slope. However, experimental observations are primarily limited by the ability of the techniques to accurately quantify the grain boundary strength and validate these theoretical models. Using high-resolution electron backscatter diffraction (HR-EBSD), the local stress tensor ahead of a slip band blocked by a grain boundary was quantified and coupled with a continuum dislocation pile-up model to assess the barrier strength of specific grain boundaries to specific slip systems, referred to as micro-Hall-Petch coefficient. For basal slip system in a deformed Mg-4Al alloy, the micro-Hall-Petch coefficient ($k^{basal}_{μ}$) varied significantly, from 0.054 to 0.184 MPa - m 1/2 for nine different grain boundaries. These results were correlated with geometric descriptors of the respective grain boundaries, with three-dimensional GB profile additionally measured via focused ion beam milling. It was found that the angle between the two slip plane traces on the grain boundary plane was the most sensitive parameter affecting $k^{basal}_{μ}$, followed by the angle between the slip directions. A functional form for calculation of $k^{basal}_{μ}$ depending on these two angles is proposed to augment crystal plasticity constitutive models with slip resistance dependent on some measure of the grain size. The method allows a new pathway to calibrate grain size strengthening parameters in crystal plasticity models, allowing further computational investigations of the interrelationship between texture, grain morphology, and the Hall Petch effect.

36 MATERIALS SCIENCE↗

Heat-transfer coefficients for air flowing in round tubes, in rectangular ducts, and around finned cylinders

Report reviews published data and presents some new data on heat transfer to air flowing in round tubes, in rectangular ducts, and around finned cylinders. The available data for heat transfer to air in straight ducts of rectangular and circular cross section have been correlated in plots of Stanton number versus Reynolds number to provide a background for the study of the data for finned cylinders. Equations are recommended for both the streamlined and turbulent regions, and data are presented for the transition region between turbulent and laminar flow. Use of hexagonal ends on round tubes causes the characteristics of laminar flow to extend to high Reynolds numbers. Average coefficients for the entire finned cylinder have been calculated from the average temperature at the base of the fins and an equation which was derived to allow for the effectiveness of the fins. The available results for each finned cylinder are correlated herein in terms of graphs of Stanton number versus Reynolds number. In general, for a given Reynolds number, the Stanton number increases with increases in both spacing and width of the fins, and is apparently independent of cylinder diameter and temperature difference. For a given coefficient of heat transfer improved baffles and rough or wavy surfaces give a substantial reduction in pumping power per unit of heat transfer surface and a somewhat smaller decrease in pressure drop. (author)

Drexel, Rober E↗

Modeling ethanol/water adsorption in all-silica zeolites using the real adsorbed solution theory

A comprehensive set of single-component and binary isotherms were collected for ethanol/water adsorption into the siliceous forms of 185 known zeolites using grand-canonical Monte Carlo simulations. Using these data, a systematic analysis of ideal/real adsorbed-solution theory (IAST/RAST) was conducted and activity coefficients were derived for ethanol/water mixtures adsorbed in different zeolites based on RAST. It was found that activity coefficients of ethanol are close to unity while activity coefficients of water are larger in most zeolites, indicating a positive excess free energy of the mixture. This observation can be attributed to water/ethanol interactions being less favorable than water/water interactions in the single-component adsorption of water at comparable loadings. The deviation from ideal behavior can be highly structure-dependent but no clear correlation with pore diameters was identified. Furthermore, our analysis also demonstrates the following: (1) accurate unary isotherms in the low-loading regime are critical for obtaining physically sensible activity coefficients; (2) the global regression scheme to solve for activity model parameters performs better than fitting activity models to activity coefficients calculated locally at each binary state point; and (3) including the dependence on adsorption potential offers only a minor benefit for describing binary adsorption at the lowest fugacities. Finally, the Margules activity model was found incapable of capturing the non-ideal adsorption behavior over the entire range of fugacities and compositions in all zeolites, but for conditions typical of solution-phase adsorption, RAST predictions using zeolite-specific or even bulk Margules parameters provide an improved description compared to IAST.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Performance and Loads Correlation of a UH-60A Slowed Rotor at High Advance Ratios

Measured data from the slowed rotor part of the 2010 UH-60A Airloads Rotor test in the NASA Ames 40- by 80- Foot Wind Tunnel are compared with CAMRAD II calculations. The emphasis in this initial study is to correlate overall trends. This analytical effort considers advance ratios from 0.3 to 1.0, with the rotor rotational speed at 40%NR. The rotor performance parameters considered are the thrust coefficient, power coefficient, L/DE, torque, and H-force. The blade loads considered are the half peak-to-peak, mid-span and outboard torsion, flatwise, and chordwise moments, and the pitch link load. For advance ratios . 0.7, the overall trends for the performance and loads (excluding the pitch link load) could be captured, but with substantial overprediction or underprediction. The correlation gradually deteriorates as the advance ratio is increased and for advance ratios . 0.8 there is no correlation. The pitch link load correlation is not good. There is considerable scope for improvement in the prediction of the blade loads. Considering the modeling complexity associated with the unconventional operating condition under consideration, the current predictive ability to capture overall trends is encouraging.

Kottapalli, Sesi B.↗

Mapping transformations for broadband atmospheric radiation calculations

Two methods of mapping the line-by-line absorption coefficient (k) spectrum onto a new variable to produce a set of k coefficients which can be used for accurate and efficient broadband radiative transfer calculations in vertically inhomogeneous, nongray scattering atmospheres are described. These methods are intended for applications for which the less accurate correlated-k method is inadequate. These methods are tested for model atmospheres containing CO2 and H2O, with pressure in the range 0.05-0.9 bar. The results obtained differed by no more than 1 or 2 percent from the line-by-line results if the number of k coefficients was about 100 times less than the number required for the line-by-line calculation. These algorithms can be used for gas mixtures and for a variety of pressure-temperature profiles.

West, Robert↗

The calculation of light element impurity (α, n) yield curves in a PuO 2 matrix and associated specific yield coefficients: Influence of the reaction cross sections

Most of the Pu separated from irradiated commercial nuclear fuel is stored as PuO 2 . The primary quantitative nondestructive measurement technique used to verify the amount of Pu in storage containers is passive neutron correlation counting. An important physical property of the oxide material is the ratio, α, of the rate of (α, n) neutrons produced inside the item to the rate of neutrons produced by spontaneous fission. This ratio influences the precision of the correlated counting method and affects the interpretation of the data because of how it changes both the primary total neutron production rate and the rate of induced fission events taking place inside the item. In addition to the main O(α, n) contribution, additional contributions come from α-particle interactions with light element impurities that are inevitably present. In this work, we calculate specific (α, n) yield coefficients, expressed in units of neutrons per second per gram of α-emitting nuclide per part per million by mass of the specified impurity element distributed in a pure PuO 2 matrix, for some key α-emitting actinides commonly present in reprocessed Pu ( 238–242 Pu+ 241 Am). These coefficients are directly applicable to nuclear safeguards verification work in which the α ratio is often calculated from the Pu-isotopic composition and chemical information obtained by other means. Further, they also provide a convenient up-to-date reference set against which values generated by other methods can be compared. Results are presented for impurities with atomic number from 3 to 17 inclusive, plus K and Fe. In most cases, these coefficients are not expected to change by more than 5%–10% at any time in the future. However, as new data become available, changes as large as 20% may be needed for some targets (e.g., F). The present yield calculations are limited by the general shortage of quality experimental total (α, n) reaction cross section data, which, together with unexplained variation between determinations, means that an objective and coherent evaluation is not possible. The situation is even less satisfactory for the partial differential cross section needed to calculate neutron spectra.

(𝛼, n) reactions↗

In situ phytoplankton absorption, fluorescence emission, and particulate backscattering spectra determined from reflectance

An inverse model was developed to extract the absortion and scattering (elastic and inelastic) properties of oceanic constituents from surface spectral reflectance measurements. In particular, phytoplankton spectral absorption coefficients, solar-stimulated chlorophyll a fluorescence spectra, and particle backscattering spectra were modeled. The model was tested on 35 reflectance spectra obtained from irradiance measurements in optically diverse ocean waters (0.07 to 25.35 mg/cu m range in surface chlorophyll a concentrations). The universality of the model was demonstrated by the accurate estimation of the spectral phytoplankton absorption coefficents over a range of 3 orders of magnitude (rho = 0.94 at 500 nm). Under most oceanic conditions (chlorophyll a less than 3 mg/cu m) the percent difference between measured and modeled phytoplankton absorption coefficents was less than 35%. Spectral variations in measured phytoplankton absorption spectra were well predicted by the inverse model. Modeled volume fluorescence was weakly correlated with measured chl a; fluorescence quantum yield varied from 0.008 to 0.09 as a function of environment and incident irradiance. Modeled particle backscattering coefficients were linearly related to total particle cross section over a twentyfold range in backscattering coefficents (rho = 0.996, n = 12).

Roesler, Collin S.↗

Pool boiling heat transfer evaluation of next-generation dielectric fluid: Opteon™ 2P50

The growing use of artificial intelligence has led to heavy thermal loads and high heat dissipation rates in data centers. Conventional air-cooled technologies are not able to fulfill these requirements. To overcome these challenges, two-phase immersion cooling (2PIC) has emerged as one of the leading technologies for high power-density chips. 2PIC increases the heat dissipation rate and efficiency of the system while reducing the footprint of the cooling equipment. A fluid with adequate dielectric properties, a suitable normal boiling temperature to maintain chip temperatures, and good material compatibility, is desired for 2PIC system. In this study, the pool boiling heat transfer of a new developmental dielectric fluid, Opteon™ 2P50, was experimentally investigated. The heat transfer coefficients at various heat fluxes (20–150 kW/m 2 ) and the critical heat flux were measured using a smooth aluminum surface. Compared with HFE-7100, Opteon™ 2P50 shows higher heat transfer coefficient (up to 59% higher) and a slightly lower value of critical heat flux (around 5.9% lower). The modified Cooper correlation with the optimized leading constant resulted in reliable prediction accuracy with a 5.3% mean absolute error percentage. Overall, these results indicate that the new dielectric fluid provides similar thermal performance to some legacy fluids.

2P50↗

Separation of volatile organic contaminants from water using a direct-contact dehumidifier: An experimental study and modeling

A packed-bed, direct-contact dehumidifier (PB-DCD) has been developed to selectively condense water from a gaseous mixture of organic contaminants. In this process, hot air is humidified by mixing with wastewater vapor in a static mixer and is dehumidified by subcooled fresh water passing through the PB-DCD in a counter-current configuration. The goal of this study is to understand the relationship between various operating parameters and how they affect separation of isopropyl alcohol (IPA) from the gaseous mixture with the purpose of expanding the investigation to other contaminants in the future. The process has been successfully used to separate IPA from wastewater. Different parameters including the concentration of IPA in water, feed temperature, air-to-vapor ratio, and cooling-water-to-vapor mass ratio, as well as residence time were examined to determine their influence on contaminant separation and clean water recovery rate. The Buckingham Pi theorem was applied to reduce the number of studying variables by generating non-dimensional groups. Experiments were performed to determine the relationship between the non-dimensional parameters and model mass transfer in the system. Mass transfer coefficients for multicomponent gaseous mixture condensation in a packed-bed direct contact condenser column are calculated and a modified correlation of mass transfer is developed. The parameters of the mass transfer model are obtained from operating conditions of the PB-DCD, stream conditions and thermodynamic properties. A modified Sherwood correlation is developed to predict IPA separation from a gaseous mixture consisting of air, water, and IPA. The modified Sherwood correlation is applied to successfully predict the Sherwood number with a mean absolute error equal to 6.6 %. According to the experimental results, the maximum IPA separation achieved was 76.3 %, which corresponds to a water recovery rate of 58.7 %.

42 ENGINEERING↗

Experimental investigation of reaction coronas on olivine in Apollo 14 high-grade breccias

Reaction coronas of pyroxene plus or minus ilmenite occur around clasts of olivine in Apollo 14 high-grade metamorphic breccias. In experiments of several months duration, there was no evidence of corona formation at 1000 C, but at 1050, with oxygen fugacity at or above Ilm-Ru-Fe and below Fe-Fe(1-x)O, incipient coronas formed around Fo(50-70), Fo(68), En(69) + Fe. Reduction of olivine under these conditions is inconsistent with the calculated stability relations and is attributed to uncertainties in the activity coefficient for olivine or pyroxene. The experiments also suggest that vesicularity in the Apollo 14 high-grade breccias may correlate with the amount of glassy material in their unmetamorphosed precursors. The metamorphic event is attributed to burial in a hot ejecta blanket, such as that of the Imbrium event.

Kesson, S. E.↗

Thermochemical response of honeycomb sandwich panels

A simple study aimed at predicting the thermochemical response of honeycomb sandwich panels is presented. The overall thermal conductivity coefficient for the panel is obtained through a consideration of the convective gas movement within the cell spaces. The earlier correlations of Catton and Edwards are used. The analytical solution for the one-dimensional approximation is quoted from an earlier study. In comparison with three data points obtained at JPL at heat fluxes of 2.5, 5 and 8 W/sq cm, the char penetration depth is well predicted, especially when the debonding of the face sheet is considered. Re-radiation of incident heat flux from the debonded face sheet plays an important role in this model.

Ramohalli, K.↗