Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

Experimental Examination of Additively Manufactured Patterns on Structural Nuclear Materials for Digital Image Correlation Strain Measurements

Abstract Background There are a limited number of commercially available sensors for monitoring the deformation of materials in-situ during harsh environment applications, such as those found in the nuclear and aerospace industries. Such sensing devices, including weldable strain gauges, extensometers, and linear variable differential transformers, can be destructive to material surfaces being investigated and typically require relatively large surface areas to attach (> 10 mm in length). Digital image correlation (DIC) is a viable, non-contact alternative to in-situ strain deformation. However, it often requires implementing artificial patterns using splattering techniques, which are difficult to reproduce. Objective Additive manufacturing capabilities offer consistent patterns using programmable fabrication methods. Methods In this work, a variety of small-scale periodic patterns with different geometries were printed directly on structural nuclear materials (i.e., stainless steel and aluminum tensile specimens) using an aerosol jet printer (AJP). Unlike other additive manufacturing techniques, AJP offers the advantage of materials selection. DIC was used to track and correlate strain to alternative measurement methods during cyclic loading, and tensile tests (up to 1100 µɛ) at room temperature. Results The results confirmed AJP has better control of pattern parameters for small fields of view and facilitate the ability of DIC algorithms to adequately process patterns with periodicity. More specifically, the printed 100 μm spaced dot and 150 μm spaced line patterns provided accurate measurements with a maximum error of less than 2% and 4% on aluminum samples when compared to an extensometer and commercially available strain gauges. Conclusion Our results highlight a new pattern fabrication technique that is form factor friendly for digital image correlation in nuclear applications.

Novich, K. A. (ORCID:0000000204466022)↗

“Additive Manufacturing: Building the Pathway Towards Process and Material Qualification”

The potential benefits of metal additive manufacturing, as compared with more traditional, subtractive-only approaches, has created excitement within design circles seeking to take advantage of the ability to build and repair complex shapes, to integrate or consolidate multiple parts and minimize joining concerns, and to locally tailor material properties to increase functionality. Tempering the excitement of designers, however, has been concerns with the material deposited by the process. It is not enough for a part to ‘look’ right from a geometric perspective. Rather, the metallurgical aspects associated with the material being deposited must ‘look’ and ‘behave’ correctly along with the aforementioned geometric accuracy. Finally, without elucidation of the connections between processing, microstructure, properties, and performance from a materials science perspective, metal additive manufacturing will not realize its potential to change the manufacturing world for property and performance-critical engineering applications.

36 MATERIALS SCIENCE↗

Microstructural, Oxidation, and Mechanical Behavior of NbTi-Based Refractory Alloys with 5 to 10 Pct Co, Cr, and Ni Additions

NbTi-based refractory alloys with additions of Co, Cr, and Ni represent an interesting medium-entropy alloy system with potential for protective oxide film formation, high strength, and ductility. This study investigates the microstructural evolution, oxidation behavior, and mechanical properties of NbTi-based alloys containing 5 to 10 at. pct Co, Cr, and Ni. CALPHAD predictions suggest that this composition range can be heat treated to obtain a predominantly body-centered cubic matrix phase. Mechanical properties, including microhardness, yield strength, maximum strength, and specific strength are evaluated through isothermal compression tests conducted between room temperature and 800 °C. The oxidation kinetics of these alloys are assessed through discontinuous oxidation tests. Parabolic oxidation kinetics were observed for NbTi–10Ni and NbTi–5Co, while linear oxidation kinetics were found for NbTi–10Cr and NbTi–10(CoCrNi). Microstructures and oxide layers are characterized using X-ray diffraction, electron backscatter diffraction, energy-dispersive X-ray spectroscopy, and scanning electron microscopy. All alloys exhibit significant mechanical softening between room temperature and 800 °C, with elastic-perfectly plastic flow observed at 800 °C. The addition of 10 pct Cr to NbTi resulted in two BCC phases up to 1050 °C, conflicting with CALPHAD predictions of a single-phase solid solution at this temperature, and resulting in higher flow stress at 800 °C. NbTi–10(CoCrNi) exhibited the lowest flow stress at 800 °C despite having more ‘cocktail effect’ potential and insufficient molar fractions of Co, Cr, or Ni to form a desirable protective oxide film.

36 MATERIALS SCIENCE↗

Full-Strength Additive Manufacturing of Pure Aluminum Alloy 7075 Using Liquid Metal Jet Printing

Additive manufacturing (AM) of high-strength aluminum alloys can produce high-performance aerospace and biomedical parts with unique geometries and functions. However, many high-performance alloy systems such as AA 7075 pose challenges during AM due to thermal cycles that cause hot cracking, limiting AM to casting-friendly alloys. Stock AA 7075 alloy poses additional challenges due to the excessive growth of insoluble precipitates during casting and needs to be thermomechanically processed to obtain acceptable mechanical properties. Here, this work uses liquid metal jet printing to produce high-resolution pure AA 7075 parts at high strength (593 MPa) and ductility (10 pct), surpassing the specific strength of any type of steel. The parts are printed by depositing fine droplets on a high-temperature substrate that reduces cooling rates, preventing hot cracking. The results show that fully dense, crack-free parts can only be printed at substrate temperatures of 500 °C with a cooling rate threshold of < 2000 K/s to prevent cracking and < 500 K/s to eliminate porosity. The tensile strength, microhardness, and ductility of the parts matched or were beyond the wrought alloy specifications after heat treatment, possibly due to high solidification rates that produce finer insoluble precipitates. Our results indicate that many challenging high-performance alloy systems can now be 3D printed based on the critical thresholds for cooling rates using any AM method that can satisfy these conditions.

36 MATERIALS SCIENCE↗

Optimization of Mineralogy and Microstructure of Solidified Basic Oxygen Furnace Slag Through SiO{sub 2} Addition or Atmosphere Control During Hot-Stage Slag Treatment

Valorization of basic oxygen furnace (BOF) slag is of significant importance for mitigation of the steel production’s environmental impact. The present work aims to investigate the influence of SiO{sub 2} addition and oxygen partial pressure on the mineralogical modification of a typical industrial BOF slag. The slag basicity (mass ratio of CaO/SiO{sub 2}) was varied from 1.8 to 4.4 by mixing specific amounts of SiO{sub 2} with the master BOF slag. The original and modified slags were remelted and solidified under argon or air atmosphere followed by slow cooling. The experimental observations were then compared with the results of thermodynamic modeling to achieve a thorough understanding. With decreasing the basicity, free lime was eliminated, as it forms dicalcium silicate (Ca{sub 2}SiO{sub 4}). With increasing oxygen partial pressure, wustite was oxidized to hematite, which combined with free lime to form calcium aluminoferrite (C{sub 2}AF). The effects of SiO{sub 2} addition and oxygen partial pressure were finally evaluated with respect to the energy consumption for the BOF slag valorization. The modified slag is suitable as a precursor for construction applications as binders.

36 MATERIALS SCIENCE↗

Effect of Al{sub 2}O{sub 3} Addition on Mineralogical Modification and Crystallization Kinetics of a High Basicity BOF Steel Slag

Basic oxygen furnace (BOF) steel slag is a main byproduct that is produced during the converter steelmaking process. The volume instability and fast crystallization of BOF slag limits its added-value application. This article aims to understand the effect of Al{sub 2}O{sub 3} on the mineralogical modification and crystallization kinetics of a high basicity BOF steel slag. Continuous cooling transformation and time–temperature–transformation curves were constructed to determine the crystallization characteristics of BOF slag. The critical cooling rate to vitrify the slag was experimentally obtained. The crystallization sequence was clarified by integrating in situ and post-mortem observations with thermodynamic calculations. The results suggest that the addition of Al{sub 2}O{sub 3} can effectively remove free lime, decrease the melting point, and improve the glass formation ability of the high basicity BOF slag. Undercooling the slag is enhanced by increasing the cooling rate and/or adding Al{sub 2}O{sub 3}. By steering the addition of Al{sub 2}O{sub 3} and the cooling rate, BOF slag can be modified to obtain a more amorphous phase, presenting an enhanced potential to be a binder for added-value applications.

36 MATERIALS SCIENCE↗

Effect of B{sub 2}O{sub 3} Addition on Electrical Conductivity and Structural Roles of CaO-SiO{sub 2}-B{sub 2}O{sub 3} Slag

The effect of B{sub 2}O{sub 3} addition on electrical conductivity of CaO-SiO{sub 2}-B{sub 2}O{sub 3} slag was investigated using the four-electrode method. The slag structure was determined from Raman and nuclear magnetic resonance spectra. The experimental results show that the electrical conductivity, as the B{sub 2}O{sub 3} content in the slag increased from 0 to 10 pct, monotonously increases from 0.0769 to 0.2642 Ω{sup −1} cm{sup −1} at temperatures ranging from 1783 to 1873 K (1510 °C to 1600 °C). The effects of temperature on electrical conductivity obeyed the Arrhenius law, and the electrical conductivity increased as the temperature increased. The Raman spectra results indicated that addition of B{sub 2}O{sub 3} led to an increase of Q{sup 3}(Si) at the cost of Q{sup 2}(Si), which will increase the degree of polymerization of the slag. {sup 11}B nuclear magnetic resonance spectra showed that both BO{sub 3} trigonal and BO{sub 4} tetrahedral structures increased with the increasing B{sub 2}O{sub 3} content. There was a competitive effect between the presence of these structures and an enhanced degree of polymerization of slags in the networks, which resulted in the increased electrical conductivity of the slag. A structure–electrical conductivity model for CaO-SiO{sub 2}-B{sub 2}O{sub 3} slag was established.

36 MATERIALS SCIENCE↗

Effect of Addition of Other Acids into Butyric Acid on Selective Leaching of Zinc from Basic Oxygen Steelmaking Filter Cake

The selective leaching of zinc over iron from basic oxygen steelmaking (BOS) filter cake was investigated using mixtures of butyric acid with acetic and/or propionic acid, HCl, or H{sub 2}SO{sub 4}. The main focus was to assess the effects of other acids on the zinc and iron leaching in butyric acid. The results show that slight reduction of zinc leaching and increase in iron leaching may take place with addition of acetic and propionic acids, causing a minor decrease in the selectivity of zinc leaching over iron. Intermittent addition of H{sub 2}SO{sub 4} and HCl was required to control the pH to be not less than that of pure butyric acid solution. Overall, an excellent selectivity can be maintained with the butyric acid–other acid mixtures. The results demonstrate the feasibility to use raw butyric acid without purification or waste butyric acid containing other impurity acids for leaching of zinc from the BOS filter cake to be recycled. Using high content of H{sub 2}SO{sub 4} in leaching is not recommended because it has a more detrimental effect on the selectivity of zinc leaching and may cause deposition of CaSO{sub 4} in the leaching residue which may increase the SO{sub 2} or CO{sub 2} emission in later high-temperature recycling processes.

36 MATERIALS SCIENCE↗

Effects of the Addition of Micro-amounts of Calcium on the Corrosion Resistance of Mg-0.1Mn-1.0Zn-xCa Biomaterials

Magnesium alloys have good biocompatibility and degradability, which are considered ideal characteristics of biomedical implants. However, there are few studies on the influence of the addition of micro-amounts of Ca on magnesium alloys. In this work, the effects of adding micro-amounts of Ca on the microstructure, mechanical properties, and corrosion properties of Mg-0.1Mn-1.0Zn-xCa (x = 0.1, 0.2, and 0.3 wt.%) alloys were investigated. The results reveal that the grain size of the alloy decreased and the yield strength and elongation both increased with increasing Ca concentrations. Corrosion tests in Kokubo simulated body fluid showed that the in vitro immersion rate first slowed down and then increased (6.395 → 6.283 → 6.395 mm/year) with increasing Ca concentrations. This phenomenon was due to the addition of Ca causing grain refinement, which slowed the corrosion rate and generated an Mg{sub 2}Ca phase to accelerate corrosion. The second-phase Mg{sub 2}Ca precipitated at the grain boundary and acted as a cathode, and the metal magnesium phase acted as an anode to form a primary battery, which caused corrosion of the magnesium phase and accelerated the corrosion rate.

36 MATERIALS SCIENCE↗

Tensile Properties of a Cast Al-Si-Mg Alloy with Reduced Si Content and Cr Addition at High Temperature

Tensile properties of an Al-Si-Mg casting alloy with reduced Si content and Cr addition were investigated at room and high temperatures. It was found that the studied alloy exhibits a remarkable performance up to 200 °C, with comparable or slightly higher strength than typical values for Al-Si-Mg-Cu alloys, commonly used for high-temperature applications, and good elongation. This is due to the choice of proper heat treatment and to the formation of dispersoids containing Cr during heat treatment, which are stable at the considered temperatures, as demonstrated by scanning and transmission electron microscopy (STEM) analysis. Interestingly, exposure to 300 °C during tensile tests enhanced an additional formation of dispersoids. It is believed that heating the material in T6 condition led to such observed dispersoids formation since precursors were already present in the Al matrix. This is not sufficient to avoid material softening at 300 °C, but it represents an interesting point in order to develop alternative heat treatment routes for dispersion-strengthened Al alloys.

36 MATERIALS SCIENCE↗

Rapid Solidification and Phase Transformations in Additive Manufactured Materials

Within the past few years, additive manufacturing (AM) has emerged as a promising manufacturing technique to enable the production of complex engineering structures with high efficiency and accuracy. Among the important factors establishing AM as a sustainable manufacturing process is the ability to control the microstructures and properties of AM products. In most AM processes, such as laser sintering (LS), laser melting (LM), and laser metal deposition (LMD), rapid solidification and high-temperature phase transformations play primary roles in determining nano- and microstructures, and consequently the mechanical and other properties of AM products. This topic of JOM is dedicated to summarizing the current research efforts in the area of rapid solidification and phase transformations in additively manufactured materials. Finally, a brief summary follows below of 10 journal articles in this topic.

36 MATERIALS SCIENCE↗

Defect Identification and Mitigation Via Visual Inspection in Large-Scale Additive Manufacturing

Defect identification and mitigation is an important avenue of research to improve the overall quality of objects created using additive manufacturing (AM) technologies. Identifying and mitigating defects takes on additional importance in large-scale, industrial AM. In large-scale AM, defects that result in failed prints are extremely costly in terms of time spent and material used. To address these issues, researchers at Oak Ridge National Laboratory’s Manufacturing Demonstration Facility investigated the use of a laser profilometer and thermal camera to collect data concerning an object as it was constructed. These data provided feedback for an in situ control system to adjust object construction. Adjustments were made in the form of automated height control. This paper presents results for both a polymer- and metal-based system. Object construction for both systems was improved significantly, and the resulting objects were more geometrically identical to the ideal 3D representation.

42 ENGINEERING↗

Low-Field Alignment of Anisotropic Bonded Magnets for Additive Manufacturing of Permanent Magnet Motors

Additive manufacturing techniques for fabricating bonded magnets have the potential to reduce manufacturing cost and time-to-market of products and address the criticality of rare-earth elements (REEs), which is a concern for economic design of dependent applications such as permanent magnet machines. We investigated the magnetic alignment of anisotropic bonded magnet material comprising 65 vol.% Nd-Fe-B in nylon-12 produced by extrusion in a 20-W brushless direct current surface permanent magnet motor for submersible water pump application using finite element analysis. The results predict that sufficient alignment for this application could be obtained at low alignment fields (μoH ≤ 1 T) with a reduction in the volume of critical materials by up to 40% compared with isotropic permanent magnets. Furthermore, this demonstrates the economic feasibility of incorporating a magnetic alignment field source into additive manufacturing systems for bonded magnets, and the potential of aligned anisotropic bonded magnets to address REE criticality.

36 MATERIALS SCIENCE↗

Discontinuous Precipitation in U-10 wt.%Mo Alloy: Reaction Kinetics, Effect of Prior gamma-UMo Microstructure, the Role of Grain-Boundary Misorientation, and the Effect of Ternary Alloying Addition

Eutectoid transformation in U-10 wt.% Mo (U10Mo) alloy initiates through discontinuous precipitation (DP) resulting in the formation of a lamellar microstructure that consists of an a-U and Mo-enriched bcc ?-UMo phase along the prior ?-UMo grain boundaries. DP is the main mode of transformation at 500°C. However, continuous precipitation (CP) of ?’ U2Mo phase together with grain-boundary DP is observed at 400°C. The reaction kinetics are noted to be very sluggish at 400°C compared to 500°C. The degree of eutectoid transformation is related to the prior ?-UMo grain size, and a smaller average grain size leads to a larger amount of transformation at a given reaction temperature. Minor addition (0.2 wt.%) of a third alloying element (Cr, Ni, Co) leads to significant changes in the nature of the DP mechanism in U10Mo alloy. In addition, high-angle grain boundaries with a misorientation of 30–45° are observed to be the major DP initiation sites. The microstructural evolution of U10Mo alloy with regard to DP-based reaction is discussed.

Jana, Saumyadeep↗

The Addition of Boron to Melt-Spun Fe-6.5%Si Ribbons

Fe-6.5%Si has higher electrical resistivity, lower magnetocrystalline anisotropy, and lower magnetostriction than traditional Fe-3.2%Si silicon steel. The reduced iron losses of Fe-6.5%Si render it a highly favorable candidate for high-speed motors and transformers. However, large-scale production of wide Fe-6.5%Si tape by rapid solidification can be challenging mainly because of its high melting point. In this work, boron is alloyed to Fe-6.5%Si to reduce its melting temperature and interfacial energy to improve the alloy’s processability. Boron additions from 0.01 wt.% to 2.24 wt.% into Fe-6.5%Si and its effect on ribbon thickness, grain size, magnetic, and mechanical properties were studied. Further, minor boron alloying significantly changed the melt pool stability and wetting on the quench wheel and in turn increased the quench rate with minimum impact on the magnetic saturation and ductility. Boron addition of < 0.06 wt.% was also found beneficial to the magnetic property of the alloy by lowering both its hysteresis and eddy current losses.

36 MATERIALS SCIENCE↗

Image-Based Fracture Surface Defect Characterization Methods for Additively Manufactured Ti-6Al-4V Tested in Fatigue

Abstract Fatigue initiation in additively manufactured samples/parts often occurs at processed-induced defects such as lack-of-fusion (LoF), keyhole, or other morphological/microstructural defects that have unique characteristics and measurable qualities. Attempts at identifying and minimizing such defects have utilized optimized processing conditions along with in situ and ex situ characterization that includes metallography and/or X-ray computed tomography (XCT). This paper highlights the benefits of using fracture surface analyses to detect and quantify defects that may not be detected by metallography/XCT due to sectioning and resolution limits. In addition to using manual quantification of fatigue initiating LoF and keyhole defects on fracture surfaces, image-based machine learning using convolutional neural networks such as U-Net were also used to automate the process. Statistical analyses were used to identify the extreme cases of defects that initiated and accelerated fatigue and to model the distribution of defect size and shape characteristics to distinguish the type of defect. Initial results show agreement between trained machine learning models and ground truth data in defect segmentation, and the distributions of defect characteristics are distinguishable to particular process-induced defect types.

Materials Science↗

Creep Deformation and Damage Mechanisms in an Advanced High-Temperature Additively Manufactured Nickel-Base Superalloy

Abstract This research investigates the processing–structure–properties–performance relationship in a novel nickel-base superalloy, ABD ® -900AM, designed for extreme environments. Specifically tailored for additive manufacturing (AM), ABD ® -900AM maintains mechanical integrity at high temperatures and is comparable to other nickel-based superalloys with a 30–40% gamma-prime volume fraction. A comprehensive study was conducted using laser-beam powder bed fusion and electron-beam powder bed fusion methods. Factors such as heat treatment, porosity, build orientation, and hot isostatic pressing were evaluated to understand their effects on microstructure and mechanical performance. Microstructural characterization revealed significant differences in grain size and orientation across build processes and heat treatments. High-temperature mechanical testing indicated that grain size, heat treatment, and orientation significantly influence creep behavior. A super-solvus heat treatment led to recrystallization and grain growth, significantly improving creep properties compared to a near-solvus heat treatment. Various creep mechanisms were identified across different conditions, and creep rupture models were developed for each build process. Post-test microstructural analysis showed grain boundary damage, with differences in creep cavitation morphology under varying stress conditions. It was shown that MC carbides grow at the expense of gamma-prime near grain boundaries, leading to precipitate-free zones in specimens tested at higher temperatures. This study fills a significant gap in fundamental research by offering a deeper insight into the high-temperature mechanical behavior of additively manufactured nickel-base superalloys. It also explores critical research questions regarding the role of carbides and the significance of heat treatment. The insights gained enhance confidence in the industry adoption of ABD ® -900AM and similar alloys for high-temperature applications, bridging the knowledge gap and supporting the development of reliable AM processes for extreme environments.

Bridges, Alex (ORCID:000000030338759X)↗

Mechanical Characteristics of Additively Manufactured ODS 316L and 316H Alloys with and Without Post-build Processing

This research aims to explore an accelerated development path for oxide dispersion-strengthened (ODS) alloys by integrating additive manufacturing (AM) technologies with recent advances in ODS materials and traditional manufacturing methods. Novel AM and post-build processing routes have been developed for ODS austenitic alloys, specifically Fe-Cr-Ni alloys like 316L and 316H. Electron microscopy and mechanical characterizations were conducted to evaluate the effects of process variables on microstructure and properties, aiming for an economically feasible route property optimization. Traditionally, ODS alloy production involves multi-day high-energy mechanical milling of alloy powder with yttria (Y 2 O 3 ) followed by powder consolidation via extrusion or other methods and additional thermomechanical processing (TMP) for property control. Here, to address these challenges associated with this complex and costly approach, we propose exploring alternative, cost-effective processing routes focusing on AM and traditional TMP methods. The new ODS alloy processing routes have achieved up to a 400% increase in yield strength and a 60% increase in ultimate tensile strength compared to wrought stainless steels while still maintaining significant ductility and fracture toughness. This paper details the novel and economical AM-based processing routes for ODS austenitic alloys, combined with post-build TMPs, and discusses the mechanical and microstructural characteristics of the developed materials.

Byun, Thak Sang [Oak Ridge National Laboratory (OR↗