Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AERODYNAMICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

Aerodynamic and Acoustic Interactions Associated with Inboard Propeller-Wing Configurations

A series of aerodynamic performance and acoustic measurements have been made on a range of inboard propeller-wing interaction configurations in the NASA Langley Low Speed Aeroacoustic Wind Tunnel (LSAWT). The results presented in this paper are part of a more expansive testing campaign encompassing both single propeller-wing and multipropeller-wing interactions, the former of which is discussed in the present work. The primary testing parameters of interest to this study are the axial and vertical positioning of the wing relative to the propeller slipstream under a constant propeller advance ratio. A multi-faceted computational effort was also employed in an effort to identify reflection and scattering effects imposed by both the wing geometry as well as the primary components of the facility test setup. This effort consisted of aerodynamic predictions using high-fidelity computational fluid dynamics (CFD), acoustic predictions using an impermeable Ffowcs Williams and Hawkings (FW-H) solver, and acoustic scattering predictions. Acoustic measurements reveal variations in the acoustic directivity behavior of the propeller blade passage frequency for even modest variations in wing position. CFD-based acoustic predictions reveal discrepancies relative to the experimental data, which is believed to be due to complex acoustic scattering behavior within the test section. Initial attempts at modeling the scattered acoustic field showed functional dependency of the acoustic amplitude variations on the wing position relative to the propeller disk, however discrepancies with experimental data remain.

Nikolas S. Zawodny↗

Improved Mars Helicopter Aerodynamic Rotor Model for Comprehensive Analyses

The Mars Helicopter is part of the NASA Mars 2020 rover mission scheduled to launch in July of 2020. Its goal is to demonstrate the viability and potential of heavier-than-air vehicles in the Martian atmosphere. Ultimately, it aims to bridge the resolution gap between orbiters and the rover as well as allow access to otherwise inaccessible regions. The low density of the Martian atmosphere and the relatively small-scale rotor result in very low Reynolds number flows. The low density and low Reynolds numbers reduce the lifting force and lifting efficiency, respectively. This paper describes the generation of the improved Mars Helicopter aerodynamic rotor model. The goal is to generate a performance model for the Mars Helicopter rotor using a free wake analysis, since this has a low computational cost for design. The improvements in the analysis are two-fold and are expanded on from two prior publications. First, the fidelity of the simulations is increased by performing higher-order two-dimensional time-accurate OVERFLOW simulations allowing for higher accuracy aerodynamic coefficients and a better understanding of the boundary layer behavior as well as its transient features. Second, a version of the model is generated to duplicate the exact testing conditions in the 25–ft. diameter Space Simulator at the Jet Propulsion Laboratory, which allows for better correlation of rotor performance figures. Previous work correlated performance with that test, but did not consider the higher temperatures in the experiment compared to those of the Martian atmosphere. The higher temperatures in the experiment are expected to give conservative performance estimates, as they give rise to an increase in speed of sound and decrease in observed Reynolds numbers.

Grip, Håvard F.↗

Optimizing Proprotor Blades Using Coupled Aeroacoustic and Aerodynamic Sensitivities

A quieter and aerodynamically more efficient proprotor design requires high-fidelity and well-integrated optimization and analysis tools. To fulfill that requirement, the present paper delivers a methodology based on multidisciplinary, adjoint-based, discrete optimization. SU2-based code development involves the implementation of aeroacoustic analysis, adjoint computations, and integrations into a multidisciplinary rotorcraft optimization suite. Submodules utilized in the optimization are verified with wind tunnel data to demonstrate the accuracy of aerodynamic and aeroacoustic analyses. The developed code is used for NASA's helically twisted proprotor to maximize the aeroacoustic performance of the proprotor while holding thrust constant. The optimization process considers multiple flight conditions (hence, multipoint), which are forward flight and hovering. As an outcome of the analyses, the optimized blade design propagates lower noise as perceived by multiple observers in both flight conditions

R Omur Icke↗

ASPIRE Aerodynamic Models and Flight Performance

The Advanced Supersonic Parachute Inflation Research Experiments (ASPIRE) project was launched in 2016 to develop a capability for testing supersonic parachutes at Mars-relevant conditions. Three parachute tests successfully tested two candidate parachute designs and qualified a parachute for NASA’s Mars 2020 mission (that successfully delivered Perseverance rover to the surface of Mars in Feb 2021). To achieve Mars-relevant densities, these parachutes were deployed at targeted conditions at high altitudes over Earth, launched via sounding rockets. ASPIRE Flight Tests provided valuable data on parachute inflation, forces, and aerodynamic behavior. Design of the flight tests depended on flight mechanics simulations which in turn required aerodynamic models for the payload, and the parachute. Computational Fluid Dynamics (CFD) was used to generate these models pre-flight and they are compared against the flight data after the tests. This talk will go over some aspects of the test design, development of pre-flight models, and comparison with flight test data.

Flight Test↗

An Aerodynamics Database for Aerocapture of a Conceptual Morphable Entry System at Mars

An aerodynamics database for aerocapture of a conceptual morphable entry system at Mars was developed. The vehicle is envisioned to employ deflections of its geometry to modulate angle of attack and sideslip angle for trajectory control. Modified Newtonian methods were used to compute hypersonic continuum aerodynamics. Direct simulation Monte Carlo calculations were carried out to compute data in the rarefied transitional regime. Free-molecular theory was used to compute values in the free-molecular regime. A bridging function method was then used to bridge data from all three flow regimes together and produce a database that can be used for future trajectory simulations to assess the vehicle’s performance. The vehicle was found to have the control authority in hypersonic continuum to effect an 18 deg change in the trim angle of attack using a 10 deg deflection of the pitching control surfaces. Similarly, a 6 deg change in the trim sideslip angle could be achieved with a 5 deg deflection of the yawing control surfaces. Different configurations of the vehicle were found to be statically stable in pitch and yaw in the continuum regime, but unstable in the rarefied and free-molecular regimes.

aerocapture↗

High-Fidelity Aerodynamic Analysis and Optimization of the SUSAN Electrofan Concept

The Subsonic Single Aft Engine (SUSAN) Electrofan is a new single-aisle regional jet class transport aircraft being studied by NASA, which benefits from reduced fuel consumption through a reduction in the number of hydrocarbon fuel-burning engines from two to one. This is achieved through a hybrid-electric system architecture, where a series of generators are used to extract power from a fuel-consuming tail cone thruster to drive electric propulsors mounted on the wings. To support the development of these propulsion systems, which involve high levels of propulsion-airframe integration, this paper presents high-fidelity analyses through computational fluid dynamics (CFD) simulations provided by the Launch Ascent and Vehicle Aerodynamics (LAVA) framework, which also includes capabilities for modeling the effect of active propulsors. A trade space exploration is performed to investigate the advantages of several wing mounted distributed electric propulsion system configurations, including over-wing, under-wing, and trailing-edge arrangements. For the aft fuselage propulsor, focus is on the sizing of the inlet, core, and bypass ducts. High-fidelity aerodynamic shape optimization is also used to help minimize the inlet distortion intensity experienced by the aft propulsor fan through a reshaping of the fuselage.

CAS↗

Small Satellite-sized Hypersonic Inflatable Aerodynamic Decelerators for Interplanetary Science Missions

To make the most of ridesharing opportunities, small satellite (SmallSat) mission designers endeavor to pack as much payload into a SmallSat-class form factor as possible. The mass and volume constraints of this smaller vehicle class present a challenge for interplanetary mission sets that require a means of achieving orbit insertion at their destination of interest. For a fully propulsive orbit insertion design, this may translate to the propellant mass being a significant fraction of the overall vehicle mass and prolonged insertion time. Aerocapture is a single quick maneuver that can significantly reduce the required propellant mass for orbit insertion. Because aerocapture uses a planet’s atmosphere to achieve the necessary change in velocity, a protective aeroshell is needed. The constraints imposed on secondary payloads render traditional rigid aeroshells mass and space prohibitive for the SmallSat class of vehicles; thus, warranting consideration of deployable designs that can be stowed compactly until needed for atmospheric entry. The Hypersonic Inflatable Aerodynamic Decelerator (HIAD) is a deployable aeroshell that leverages inflatable toroids to achieve the large drag area needed for aerodynamic deceleration. While the technology is currently being analyzed for Mars human-scale missions, it has the potential applicability for interplanetary SmallSat-scale missions as well. This paper highlights a study conducted during an internship at NASA Langley Research Center to investigate the feasibility of using a scaled-down HIAD design in SmallSat aerocapture missions. Several scaling methodologies are investigated including use of parametric models and direct computer-aided design (CAD) model scaling. Candidate HIAD configurations that conform to secondary payload adapter requirements are identified. The Program to Optimize Simulated Trajectories II (POST2) is utilized to conduct orbit insertion performance and trajectory sensitivity studies using the candidate configurations at Earth, Venus, and Mars. The results of the study indicate that multiple SmallSat-sized HIAD designs, targeting a range of SmallSat payload classes, are feasible for planetary aerocapture missions to Mars and Venus as well as Earth-based aerocapture missions.

Shelly C. Mann↗

Experimental Validation of an Acoustically and Aerodynamically Optimized UAM Proprotor Part 1: Test Setup and Results

Vehicles with vectored thrust capabilities are common configurations proposed for Urban Air Mobility (UAM) flight missions. These include proprotor systems capable of vertical takeoff and landing (VTOL), axial forward flight, and the intermediate transition phases of vehicle flight. The aerodynamic loading requirements as well as resulting acoustics during these different phases of flight can vary considerably. An optimization effort was undertaken with the objective of minimizing radiated tonal acoustics of a proprotor system for both static hover and axial forward flight conditions, while simultaneously preserving aerodynamic performance relative to a baseline propeller design.

Nikolas S. Zawodny↗

FUN3D Analyses of the 5th AIAA Propulsion Aerodynamics Workshop Inlet Test Case

This work presents the results of FUN3D analyses that were performed for the 5th AIAA Propulsion Aerodynamics Workshop. The workshop was separated into two sections that focused on inlet and nozzle flows. This paper focuses on the inlet section of the workshop, which considered an axisymmetric inlet in close-proximity to the ground and subjected to a crosswind. Four levels of grid refinement were provided by the workshop committee. Participants were asked to perform simulations for three crosswind velocities on a minimum of three levels of grid refinement, for a total of nine required cases. This work employed an updated set of grids provided by the committee after completion of the workshop based on feedback from participants. The updated grids featured a larger computational domain and increased refinement near the ground vortex region. This work employed the three coarsest grid levels from the updated grid set. Note that an additional extension downstream of the inlet was added to the provided grids for this work to mitigate observed convergence issues. Additionally, a limited turbulence model study was performed for the highest value of crosswind velocity and the finest grid. The results show that grid convergence was only achieved for the case with the lowest value of crosswind velocity. However, the results were generally observed to improve, relative to the experimental data, with increasing grid refinement. The FUN3D predictions were observed to agree qualitatively with the provided experimental data. However, FUN3D exhibited a tendency to underpredict the minimum value of the radially averaged total pressure at the Aerodynamic Interface Plane, which is consistent with the general findings from the workshop. Overall, FUN3D was found to perform well relative to its peers for the PAW5 workshop inlet test case.

PAI↗

FUN3D Analyses of the 5th AIAA Propulsion Aerodynamics Workshop Inlet Test Case

This work presents the results of FUN3D analyses that were performed for the 5th AIAA Propulsion Aerodynamics Workshop. The workshop was separated into two sections that focused on inlet and nozzle flows. This paper focuses on the inlet section of the workshop, which considered an axisymmetric inlet in close-proximity to the ground and subjected to a crosswind. Four levels of grid refinement were provided by the workshop committee. Participants were asked to perform simulations for three crosswind velocities on a minimum of three levels of grid refinement, for a total of nine required cases. This work employed an updated set of grids provided by the committee after completion of the workshop based on feedback from participants. The updated grids featured a larger computational domain and increased refinement near the ground vortex region. This work employed the three coarsest grid levels from the updated grid set. Note that an additional extension downstream of the inlet was added to the provided grids for this work to mitigate observed convergence issues. Additionally, a limited turbulence model study was performed for the highest value of crosswind velocity and the finest grid. The results show that grid convergence was only achieved for the case with the lowest value of crosswind velocity. However, the results were generally observed to improve, relative to the experimental data, with increasing grid refinement. The FUN3D predictions were observed to agree qualitatively with the provided experimental data. However, FUN3D exhibited a tendency to underpredict the minimum value of the radially averaged total pressure at the Aerodynamic Interface Plane, which is consistent with the general findings from the workshop. Overall, FUN3D was found to perform well relative to its peers for the PAW5 workshop inlet test case.

PAI↗

Comparison of Aerodynamic Analysis Tools Applied to a Propeller-Blown Wing

This paper describes initial results from an ongoing activity comparing two aerodynamic analysis tools: OVERFLOW, a Navier-Stokes flow solver, and FlightStream, a viscous surface-vorticity, unstructured panel method flow solver. Both tools are applied to analyses of an unblown wing and a propeller-blown wing, and then comparisons are performed between the predicted aerodynamic loads and moments from each tool. Computational performance and efficiencies of each tool and their usability in conceptual and preliminary air vehicle design are also discussed. A description of the workflow, underlying theoretical foundations, and best practices are provided. In comparing FlightStream and OVERFLOW, reasonable agreement between predicted performance is observed for flow regimes of interest at high angle of attack prior to stall, including blown wing aero-propulsive effects on lift augmentation and stall delay. In the post-stall regions, FlightStream appears to underestimate the effects of turbulent flow separation that contribute heavily to drag. However, as expected for a high-fidelity, time-accurate solver, the setup and computation time are substantially greater for OVERFLOW than for FlightStream.

Vivek Ahuja↗

Comparison of Aerodynamic Analysis Tools Applied to a Propeller-Blown Wing

This paper describes initial results from an ongoing activity comparing two aerodynamic analysis tools: OVERFLOW, a Navier-Stokes flow solver, and FlightStream, a viscous surface-vorticity, unstructured panel method flow solver. Both tools are applied to analyses of an unblown wing and a propeller-blown wing, and then comparisons are performed between the predicted aerodynamic loads and moments from each tool. Computational performance and efficiencies of each tool and their usability in conceptual and preliminary air vehicle design are also discussed. A description of the workflow, underlying theoretical foundations, and best practices are provided. In comparing FlightStream and OVERFLOW, reasonable agreement between predicted performance is observed for flow regimes of interest at high angle of attack prior to stall, including blown wing aero-propulsive effects on lift augmentation and stall delay. In the post-stall regions, FlightStream appears to underestimate the effects of turbulent flow separation that contribute heavily to drag. However, as expected for a high-fidelity, time-accurate solver, the setup and computation time are substantially greater for OVERFLOW than for FlightStream.

Vivek Ahuja↗

Numerical Study on the Aerodynamics of an Iced Airfoil With Scale-Resolving Simulations

Scale-resolving simulations of the NACA 23012 airfoil with horn ice accretion on the leading edge are conducted using the hybrid Reynolds-averaged Navier–Stokes/large-eddy simulation (hybrid RANS/LES) and wall-modeled large-eddy simulation (WMLES) approaches implemented in the Launch, Ascent, and Vehicle Aerodynamics (LAVA) framework. Aerodynamic results at the Reynolds number of 1.8 million show good comparison with the experimental measurements at different angles of attack from pre-stall to post-stall regimes. The pressure plateaus caused by the flow separation and the recovery of pressure inside the separation bubble around the iced leading edge are well predicted with the scale-resolving simulations when sufficient grid resolution is used around the accreted ice. The unsteadiness of the turbulent flows around the iced airfoil is also examined through the turbulent kinetic energy with the Reynolds normal stress anisotropy. Kelvin–Helmholtz instability (KHI) arises at the shear layer triggered by the upper ice horn and leads to rapid laminar-to-turbulent transition over a large range of angle of attack. With the increase of the angle of attack, the region with high turbulence intensity induced by the unstable shear layer spreads quickly over the entire upper surface of the airfoil. The coherent KHI modes from the upper and lower ice horns are extracted using the spectral proper orthogonal decomposition (SPOD) technique. The SPOD modes extracted from the upper shear layer have large-scale variations in the spanwise direction and low-rank behavior where the energy of the leading SPOD mode at each Strouhal number of the KHI largely represents the total energy when the mode number in the spanwise direction is small.

ARMD↗

Numerical Study on the Aerodynamics of an Iced Airfoil With Scale-Resolving Simulations

Scale-resolving simulations of the NACA 23012 airfoil with horn ice accretion on the leading edge are conducted using the hybrid Reynolds-averaged Navier–Stokes/large-eddy simulation (hybrid RANS/LES) and wall-modeled large-eddy simulation (WMLES) approaches implemented in the Launch, Ascent, and Vehicle Aerodynamics (LAVA) framework. Aerodynamic results at the Reynolds number of 1.8 million show good comparison with the experimental measurements at different angles of attack from pre-stall to post-stall regimes. The pressure plateaus caused by the flow separation and the recovery of pressure inside the separation bubble around the iced leading edge are well predicted with the scale-resolving simulations when sufficient grid resolution is used around the accreted ice. The unsteadiness of the turbulent flows around the iced airfoil is also examined through the turbulent kinetic energy with the Reynolds normal stress anisotropy. Kelvin–Helmholtz instability (KHI) arises at the shear layer triggered by the upper ice horn and leads to rapid laminar-to-turbulent transition over a large range of angle of attack. With the increase of the angle of attack, the region with high turbulence intensity induced by the unstable shear layer spreads quickly over the entire upper surface of the airfoil. The coherent KHI modes from the upper and lower ice horns are extracted using the spectral proper orthogonal decomposition (SPOD) technique. The SPOD modes extracted from the upper shear layer have large-scale variations in the spanwise direction and low-rank behavior where the energy of the leading SPOD mode at each Strouhal number of the KHI largely represents the total energy when the mode number in the spanwise direction is small.

ARMD↗

Fan Noise Predictions of the NASA Source Diagnostic Test Using Unsteady Simulations with LAVA Part I: Near-Field Aerodynamics and Turbulence

A sliding mesh technique within the Launch, Ascent, and Vehicle Aerodynamics (LAVA) computational framework is validated using the experimental dataset collected as part of the NASA Source Diagnostic Test (SDT) campaign. Two modeling approaches are explored: the unsteady Reynolds-Averaged Navier Stokes (URANS) with Spalart-Allmaras (SA) turbulence model closure, and a hybrid Reynolds-Averaged Navier Stokes/Large Eddy Simulation (RANS/LES) paradigm employing a Zonal Detached Eddy Simulation (ZDES) closure with enhanced shielding protection. Fan stage performance metrics, aerodynamic quantities and turbulent flow structures are analyzed in this work. Initial studies focusing on grid and time-step sensitivity are presented. Sensitivity to different variants of the SA turbulence model is analyzed, supporting the use of the baseline SA model in the production runs. Two conditions are analyzed in detail using URANS and hybrid RANS/LES (HRLES). Mean flow quantities are well-captured by both methods in the low-speed (approach) regime. While URANS misses all the upstream-propagating noise in the inlet due to the rotor-locked tones being evanescent in nature at subsonic fan tip speeds, HRLES captures this broadband component in its pressure field. At the high-speed (sideline) condition, URANS shows better agreement with the SDT data than HRLES in the interstage flow-field. In this regime, URANS captures the tonal content propagating through the inlet, since the tones are now cut-on. Both methods are suitable to capture fan stage performance metrics and mean flow quantities, but only HRLES is able to resolve the fine turbulent structures responsible for broadband noise. The results support the use of the sliding mesh technique implemented in this work for future turbomachinery applications within the LAVA solver framework.

AATT↗

Fan Noise Predictions of the NASA Source Diagnostic Test Using Unsteady Simulations with LAVA Part I: Near-Field Aerodynamics and Turbulence

A sliding mesh technique within the Launch, Ascent, and Vehicle Aerodynamics (LAVA) computational framework is validated using the experimental dataset collected as part of the NASA Source Diagnostic Test (SDT) campaign. Two modeling approaches are explored: the unsteady Reynolds-Averaged Navier Stokes (URANS) with Spalart-Allmaras (SA) turbulence model closure, and a hybrid Reynolds-Averaged Navier Stokes/Large Eddy Simulation (RANS/LES) paradigm employing a Zonal Detached Eddy Simulation (ZDES) closure with enhanced shielding protection. Fan stage performance metrics, aerodynamic quantities and turbulent flow structures are analyzed in this work. Initial studies focusing on grid and time-step sensitivity are presented. Sensitivity to different variants of the SA turbulence model is analyzed, supporting the use of the baseline SA model in the production runs. Two conditions are analyzed in detail using URANS and hybrid RANS/LES (HRLES). Mean flow quantities are well-captured by both methods in the low-speed (approach) regime. While URANS misses all the upstream-propagating noise in the inlet due to the rotor-locked tones being evanescent in nature at subsonic fan tip speeds, HRLES captures this broadband component in its pressure field. At the high-speed (sideline) condition, URANS shows better agreement with the SDT data than HRLES in the interstage flow-field. In this regime, URANS captures the tonal content propagating through the inlet, since the tones are now cut-on. Both methods are suitable to capture fan stage performance metrics and mean flow quantities, but only HRLES is able to resolve the fine turbulent structures responsible for broadband noise. The results support the use of the sliding mesh technique implemented in this work for future turbomachinery applications within the LAVA solver framework.

AATT↗

Evaluation of Voronoi Meshes for Large Eddy Simulations of High Lift Aerodynamics

Numerical sensitivity to 3 different Voronoi seeding methods is investigated for Large Eddy Simulations (LES). A second order accurate, non-dissipative finite volume discretization is used to systematically investigate the effects of different polyhedral Voronoi mesh types using a sequence of three canonical problems with increasing complexity. First, inviscid isentropic vortex propagation is studied to demonstrate the substantial reduction of errors for rhombic dodecahedron and truncated octahedral cell types over Cartesian hexagonal cells of identical spacing. Furthermore, the reduction of errors induced at cell-size transitions (grid-coarsening interfaces) due to Lloyd smoothing iterations is quantified. It is shown that by utilizing an appropriate viscous flux discretization, a constant coefficient subgrid scale model is sufficient for non-linear stability at the 2:1 cell-size transitions on polyhedral grids, although some further error reduction does occur when smoothing is utilized. Next, forced homogeneous isotropic turbulence at an asymptotically large Reynolds number is studied to demonstrate the non-dissipative character of the inviscid flux discretization, and the non-linear robustness and accuracy offered by the viscous flux discretization using a subgrid scale model for all three Voronoi grid types. Finally,Wall-Modeled Large Eddy Simulations (WMLES) are performed to study the high-lift aerodynamics on the McDonnell Douglas 30P30N multi-element airfoil at two distinct grid levels and for two distinct Voronoi cell types. The formulation is shown to predict the aerodynamic loading with high accuracy at all angles of attack when sufficient resolution is reached, and the hexagonal prism grid topology, while computationally more expensive, has higher effective resolution compared to the Cartesian grid topology with the same spacing.

TTT↗

Evaluation of Voronoi Meshes for Large Eddy Simulations of High Lift Aerodynamics

Numerical sensitivity to 3 different Voronoi seeding methods is investigated for Large Eddy Simulations (LES). A second order accurate, non-dissipative finite volume discretization is used to systematically investigate the effects of different polyhedral Voronoi mesh types using a sequence of three canonical problems with increasing complexity. First, inviscid isentropic vortex propagation is studied to demonstrate the substantial reduction of errors for rhombic dodecahedron and truncated octahedral cell types over Cartesian hexagonal cells of identical spacing. Furthermore, the reduction of errors induced at cell-size transitions (grid-coarsening interfaces) due to Lloyd smoothing iterations is quantified. It is shown that by utilizing an appropriate viscous flux discretization, a constant coefficient subgrid scale model is sufficient for non-linear stability at the 2:1 cell-size transitions on polyhedral grids, although some further error reduction does occur when smoothing is utilized. Next, forced homogeneous isotropic turbulence at an asymptotically large Reynolds number is studied to demonstrate the non-dissipative character of the inviscid flux discretization, and the non-linear robustness and accuracy offered by the viscous flux discretization using a subgrid scale model for all three Voronoi grid types. Finally, Wall-Modeled Large Eddy Simulations (WMLES) are performed to study the high-lift aerodynamics on the McDonnell Douglas 30P30N multi-element airfoil at two distinct grid levels and for two distinct Voronoi cell types. The formulation is shown to predict the aerodynamic loading with high accuracy at all angles of attack when sufficient resolution is reached, and the hexagonal prism grid topology, while computationally more expensive, has higher effective resolution compared to the Cartesian grid topology with the same spacing.

TTT↗