Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ACOUSTIC TESTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

Wear Test Demonstration of a Technique to Mitigate Keeper Erosion in a High-Current LaB6 Hollow Cathode

The results of a wear test on a 100-A LaB6 hollow cathode are presented as verification of a technique to mitigate keeper erosion caused by sputtering from anomalously high-energy ions. The ions responsible for this erosion have been theorized to result from the onset ion acoustic turbulence in the plume of the cathode. The proposed technique to minimize the erosion relies on identifying operating conditions where the energy of the ion acoustic turbulence is low. 100 hour wear tests are conducted on a high-current hollow cathode with a molybdenum keeper at three operating conditions: two with low turbulence levels and one with high turbulence levels. It is demonstrated that the keeper exhibits low levels erosion (at a peak erosion rate of around 0.035 um/hour) that can be explained by classical mechanisms at the low turbulence states, and anomalously high sputtering (at a peak erosion rate of.07 um/hour) at the high erosion state.

Ho, Amanda K.↗

Application of the Discontinuous Galerkin Method to Acoustic Scatter Problems

The application of the quadrature-free form of the discontinuous Galerkin method to two problems from Category 1 of the Second Computational Aeroacoustics Workshop on Benchmark problems is presented. The method and boundary conditions relevant to this work are described followed by two test problems, both of which involve the scattering of an acoustic wave off a cylinder. The numerical test performed to evaluate mesh-resolution requirements and boundary-condition effectiveness are also described.

Atkins, H. L.↗

The influence of source acceleration on acoustic signals

The effect of aircraft acceleration on acoustic signals is often ignored in both analytical studies and data reduction of flight test measurements. In this study, the influence of source acceleration on acoustic signals is analyzed using computer simulated signals for an accelerating point source. Both rotating and translating sources are considered. Using a known signal allows an assessment of the influence of source acceleration on the received signal. Aircraft acceleration must also be considered in the measurement and reduction of flyover noise. Tracking of the aircraft over an array of microphones enables ensemble averaging of the acoustic signal, thus increasing the confidence in the measured data. This is only valid when both the altitude and velocity remain constant. For an accelerating aircraft, each microphone is exposed to differing flight velocities, Doppler shifts, and smear angles. Thus, averaging across the array in the normal manner is constrained by aircraft acceleration and microphone spacing. In this study computer simulated spectra, containing acceleration, are averaged across a 12 microphone array mimicking a flight test with accelerated profile in which noise data was obtained. Overlapped processing is performed is performed in the flight test measurements in order to alleviate spectral smearing.

Kelly, Jeffrey J.↗

Geophysical monitoring using active seismic techniques at the Citronelle Alabama CO 2 storage demonstration site

Between August 2012 and September 2014, about 114,000 metric tonnes of CO 2 was captured from the coal-fired Plant Barry Power Station at Bucks Alabama and injected into the Paluxy Formation above the oil pool in the southeast unit of the Citronelle Oilfield. Various monitoring methods were deployed at land surface and in project wells to measure system performance, comply with permit requirements and test new and innovative monitoring tools. The monitoring program relied heavily on active seismic methods for subsurface imaging of geologic structure and time-lapse seismic techniques to track the CO 2 migration in the injection interval. Both conventional geophone/hydrophone and fiber-optic based Distributed Acoustic Sensing (DAS) arrays were deployed and tested, allowing a side by side comparison of the equipment and techniques. Geophysical imaging of the subsurface was successful using DAS in the offset vertical seismic profile (OVSP) survey configuration. A high resolution OVSP image of the subsurface was obtained in 2014 with DAS, which exceeded project expectations in comparison to a lower resolution image obtained in 2012 using a conventional 80-level geophone array. A time-lapse image of the redistribution of CO 2 after injection ended in September 2014 was obtained with two DAS OVSP surveys from June 2014 and December 2015, thus successfully demonstrating its proof-of-concept. Unfortunately, a pre-injection baseline survey with DAS, which was in its initial stage of technology development in 2012, did not have sufficient quality for use, making it difficult to interpret the acquired DAS time-lapse difference. Additional research in this area has since demonstrated the utility of time-lapse DAS OVSP. DAS data were also acquired during a cross-well seismic survey conducted in 2014. Unfortunately, the DAS technique was not success in the cross-well survey configuration because the system noise level was too high in the crosswell frequency output range (100–1200 Hz) of the piezoelectric source (increasing by a factor of ten compared to VSP frequency band). Additionally, the cross-well geometry causes sub-horizontal (broadside) incidence on the vertical DAS fiber cable, which is known to be problematic. Current research is focused on improving the DAS cable response to broadside acoustic energy. Time-lapse seismic surveys using commercially available conventional arrays were also acquired. In contrast to the DAS acquired data, the cross-well seismic results obtained with the conventional array was highly successful and clearly showed the CO 2 remained in zone at the end of injection. Time-lapse differencing of the OSVP surveys acquired with the conventional arrays proved to be inconclusive. Finally, changes in wellbore conditions between surveys and unavoidable changes in equipment (the array used for the baseline survey was retired) affected data quality, making it difficult to interpret the OVSP results.

58 GEOSCIENCES↗

Acoustic Emission Detection of Impact Damage on Space Shuttle Structures

The loss of the Space Shuttle Columbia as a result of impact damage from foam debris during ascent has led NASA to investigate the feasibility of on-board impact detection technologies. AE sensing has been utilized to monitor a wide variety of impact conditions on Space Shuttle components ranging from insulating foam and ablator materials, and ice at ascent velocities to simulated hypervelocity micrometeoroid and orbital debris impacts. Impact testing has been performed on both reinforced carbon composite leading edge materials as well as Shuttle tile materials on representative aluminum wing structures. Results of these impact tests will be presented with a focus on the acoustic emission sensor responses to these impact conditions. These tests have demonstrated the potential of employing an on-board Shuttle impact detection system. We will describe the present plans for implementation of an initial, very low frequency acoustic impact sensing system using pre-existing flight qualified hardware. The details of an accompanying flight measurement system to assess the Shuttle s acoustic background noise environment as a function of frequency will be described. The background noise assessment is being performed to optimize the frequency range of sensing for a planned future upgrade to the initial impact sensing system.

Prosser, William H.↗

RS-88 Pad Abort Demonstrator Thrust Chamber Assembly Testing at NASA Marshall Space Flight Center

This paper documents the effort conducted to collect hot-tire dynamic and acoustics environments data during 50,000-lb thrust lox-ethanol hot-fire rocket testing at NASA Marshall Space Flight Center (MSFC) in November-December 2003. This test program was conducted during development testing of the Boeing Rocketdyne RS-88 development engine thrust chamber assembly (TCA) in support of the Orbital Space Plane (OSP) Crew Escape System Propulsion (CESP) Program Pad Abort Demonstrator (PAD). In addition to numerous internal TCA and nozzle measurements, induced acoustics environments data were also collected. Provided here is an overview of test parameters, a discussion of the measurements, test facility systems and test operations, and a quality assessment of the data collected during this test program.

Farr, Rebecca A.↗

Thermoacoustic fatigue testing facility for space shuttle thermal protection system

The development of a reusable space shuttle by NASA in the next decade depends in part on the design of a satisfactory thermal protection system (TPS). The booster and orbiter parts of the shuttle require TPS panels which will withstand thermoacoustic fatigue. The Langley Research Center has begun tests on early panel designs in a new acoustic fatigue facility which is capable of simulating the combined elevated temperature and acoustic environments which these panels are expected to experience. The capabilities of the facility and computer system are outlined, and problems encountered in establishing the test methods are discussed. Tests of a Haynes 25 TPS panel are described, and representative data from tests of the panel at 650 C are included.

Rucker, C. E.↗

Combustor fluctuating pressure measurements in-engine and in a component test facility - A preliminary comparison

Combustor internal fluctuating pressure and far-field noise generated in a YF-102 turbofan engine are investigated; combustor internal measurements are also made in a duct-component test facility operating over a range of conditions encompassing those characteristic of the aircraft engine. Although directly measured spectra for the engine and the duct-component test facility show discrepancies, the results of coherence function, transfer function and phase relationship comparisons suggest that the internal dynamics of the combustor as an acoustic source may be preserved in a component test facility.

Reshotko, M.↗

Model-Scale Aerodynamic Performance Testing of Proposed Modifications to the NASA Langley Low Speed Aeroacoustic Wind Tunnel

Tests were performed on a 1/20th-scale model of the Low Speed Aeroacoustic Wind Tunnel to determine the performance effects of insertion of acoustic baffles in the tunnel inlet, replacement of the existing collector with a new collector design in the open jet test section, and addition of flow splitters to the acoustic baffle section downstream of the test section. As expected, the inlet baffles caused a reduction in facility performance. About half of the performance loss was recovered by addition the flow splitters to the downstream baffles. All collectors tested reduced facility performance. However, test chamber recirculation flow was reduced by the new collector designs and shielding of some of the microphones was reduced owing to the smaller size of the new collector. Overall performance loss in the facility is expected to be a 5 percent top flow speed reduction, but the facility will meet OSHA limits for external noise levels and recirculation in the test section will be reduced.

Booth, Earl R., Jr.↗

Design and Evaluation of Modifications to the NASA Langley Flow Impedance Tube

The need to minimize fan noise radiation from commercial aircraft engine nacelles continues to provide an impetus for developing new acoustic liner concepts. If the full value of such concepts is to be attained, an understanding of grazing flow effects is crucial. Because of this need for improved understanding of grazing flow effects, the NASA Langley Research Center Liner Physics Group has invested a large effort over the past decade into the development of a 2-D finite element method that characterizes wave propagation through a lined duct. The original test section in the Langley Grazing IncidenceTube was used to acquire data needed for implementation of this finite element method. This test section employed a stepper motor-driven axial-traversing bar, embedded in the wall opposite the test liner, to position a flush-mounted microphone at pre-selected locations. Complex acoustic pressure data acquired with this traversing microphone were used to educe the acoustic impedance of test liners using this 2-D finite element method and a local optimization technique. Results acquired in this facility have been extensively reported, and were compared with corresponding results from various U.S. aeroacoustics laboratories in the late 1990 s. Impedance data comparisons acquired from this multi-laboratory study suggested that it would be valuable to incorporate more realistic 3-D aeroacoustic effects into the impedance eduction methodology. This paper provides a description of modifications that have been implemented to facilitate studies of 3-D effects. The two key features of the modified test section are (1) the replacement of the traversing bar and its flush-mounted microphone with an array of 95 fixed-location microphones that are flush-mounted in all four walls of the duct, and (2) the inclusion of a suction device to modify the boundary layer upstream of the lined portion of the duct. The initial results achieved with the modified test section are provided in this report, and a comparison of these results with those achieved using the original test section is used to demonstrate that the data acquisition and analysis with the new test section can be confidently used for impedance eduction.

Jones, Michael G.↗

Initial Investigation of the Acoustics of a Counter-Rotating Open Rotor Model with Historical Baseline Blades in a Low-Speed Wind Tunnel

A counter-rotating open rotor scale model was tested in the NASA Glenn Research Center 9- by 15-Foot Low-Speed Wind Tunnel (LSWT). This model used a historical baseline blade set with which modern blade designs will be compared against on an acoustic and aerodynamic performance basis. Different blade pitch angles simulating approach and takeoff conditions were tested, along with angle-of-attack configurations. A configuration was also tested in order to determine the acoustic effects of a pylon. The shaft speed was varied for each configuration in order to get data over a range of operability. The freestream Mach number was also varied for some configurations. Sideline acoustic data were taken for each of these test configurations.

Acoustics↗

Acoustic measurements of a full-scale coaxial hingeless rotor helicopter

Acoustic data were obtained during a full-scale test of the XH-59A Advancing Blade Concept Technology Demonstrator in the 40- by 80-Foot Wind Tunnel. The XH-59A is a research helicopter with two coaxial rotors and hingeless blades. Performance, vibration, and noise at various forward speeds, rotor lift coefficients and rotor shaft angles of attack were investigated. The noise data were acquired over an isolated rotor lift coefficient range of 0.024 to 0.162, an advance ratio range of 0.23 to 0.45 corresponding to tunnel wind speeds of 89 to 160 knots, and angles of attack from 0 deg to 10 deg. Acoustic data are presented for seven microphone locations for all run conditions where the model noise is above the background noise. Model test configuration and performance information are also listed. Acoustic waveforms, dBA, and 1/3-octave spectra as functions of operating condition for selected data points and microphones are presented. In general, the noise level is shown to increase with rotor lift coefficient except under certain operating conditions where significant impulsive blade/vortex interactions increase noise levels.

Peterson, R. L.↗

Investigation of Anti-Phase Asymmetric Quiet Rotor Technology

The future of urban air mobility has a well-known tall pole challenge in the form of community acceptance which largely comes from the noise. This paper presents a proposed anti-phase rotor technology that could reduce noise sources such as blade vortex interaction noise. The anti-phase rotor technology includes a rotor design with various anti-phase alternating trailing edge patterns and a rotor design with an asymmetric blade tip. Four small-scale anti-phase rotors are fabricated by 3D printing for acoustic measurements conducted in a low-speed open-circuit wind tunnel to assess the effectiveness of the proposed anti-phase rotor technology. Preliminary test results appear to be promising and indicate that the anti-phase rotor designs could be a practical means of reducing blade vortex interactions and noise. The four tested anti-phase rotor designs have peak acoustic performance depending on the RPM and thrust which suggests improved performance through design optimization could be achieved for specific mission requirements.

Cramer, Nicholas B.↗

Low Temperature Reliability of Electronic Packages/Assemblies for Space Missions

A NASA-wide team, funded under the NASA Electronic Parts and Packaging Program (NEPP), was formed to collaborate and to establish reliability of various electronic parts/packaging and assemblies for operation under extreme cold temperatures. One of the primary objectives of the NEPP is to expedite the infusion of cutting edge technologies into the present and future NASA missions. Commercial-off-the-shelf (COTS) emerging electronic parts/packages due to their lower weight, increased functionality, and lower cost are excellent candidates for space missions if they are characterized to show that they will meet the stringent reliability and quality requirements. Characterizations, especially for the extreme cold temperatures, are required since very limited data are available by manufacturers or users. For severe military environments, the temperature conditions to -65 C are the lowest temperature for which these parts/packages and assemblies are qualified. New data beyond this relatively benign cold temperature are required for numerous NASA missions. Several parts/packages, based on the project recommendation for their immediate and future needs, were selected for detailed characterization to cold temperature regimes down to liquid nitrogen (-196 C), covering both Mars cold temperature (-125 C) and asteroid (- 180 C) lander environmental requirements. Numerous parts/packages and assemblies were characterized during extreme temperature environmental tests. Several electrical parameters were characterized at discrete temperatures to -185 C to determine if they remain within their specification ranges. Both packages and circuit boards were subjected to nondestructive testing including optical, X-ray, and acoustic microscopy to document their integrity prior to environment exposure. Package/board assemblies were also subjected to X-ray to characterize solder joint integrity including void levels. Both parts and assemblies were subjected to thermal cycling with a large temperature swing enveloping numerous NASA missions. Details of the performed tests and the results obtained are presented.

Patterson, Richard L.↗

Detection and Perception of Sound by Eagles and Surrogate Raptors

One overarching objective of this program of study was the accumulation of objective, scientifically valid information relating to auditory performance of bald and golden eagles that may be used to guide the development of acoustic alerting/deterrence technologies intended to discourage encroachment into wind energy air spaces. To that end, analyses aimed at the characterization of sensitivity to sound in bald and golden eagles, along with findings in the supra-threshold, dynamic frequency spaces related to response latencies and amplitudes, leads us to conclude that bald, and golden eagles navigate the same basic working auditory space, as in other known and thus far characterized members of the diurnal raptor family. Specifically, bald and golden eagles, along with other raptor species within the group, operate in an auditory space characterized by a frequency band at least four octaves wide and centered on 2 kHz, with an upper frequency limit between 6 and 10 kHz at 80 dB SPL and a lower frequency limit that almost certainly extends below 0.2 kHz. Consequently, we recommend that signal designers use these data as a guideline in efforts to design effective and efficient acoustic alerting/deterrent systems. It is important to note that signal energy broadcast outside of this frequency band at moderate levels will not contribute to the efficacy of a deterrent but will add an unnecessary fraction to the overall acoustic pollution budget. The importance of this consideration is heightened by contemporaneous concerns related to the transmission of noise broadcast by wind energy farms. In addition, based on analyses of data acquired from red-tailed hawks using the same experimental paradigm and data acquisition system, we conclude that auditory function in the red-tailed hawk is sufficiently like that observed in bald and golden eagles to permit its use as a surrogate species. Response waveforms, threshold-frequency curves, and input-output characteristics match those of eagles closely. It should be noted however, that differences in sensitivity and slightly extended high-frequency limits of hearing should be taken into account when extrapolating findings from one species to the others. Although the inclusion of behavioral tests of red-tailed hawks to acoustic stimuli was beyond the scope of this investigation, future efforts to assess response parameters like signal-type preference and habituation rate will further elucidate their suitability to serve as eagle surrogates in behavioral studies; nonetheless, the species in question are well matched with respect to basic auditory performance. A second essential objective of this program of study was the acoustic characterization of a subset of calls comprising the vocal repertoires of bald and golden eagles that may be used to supplement auditory performance findings in the effort to guide the development of acoustic alerting signals. With regard to that objective, the vocal repertoires of both bald and golden eagle species are rich and varied. While similar in spectrographic structure, distinctive differences are also clear. Generally, golden eagles produce some calls with shorter durations, and similar “sounding” calls exhibit distinctively different spectrographic patterns than those of bald eagles. Both species produce calls that contain a wide variety of nonlinear elements that operate to enhance the rich and varied nature of commonly observed vocal products. Comparison of the average power spectra of commonly observed bald and golden eagle calls with threshold-frequency curves leads to the conclusion that call energies fall within the frequency bounds of hearing. Further, the acoustic energy of calls considered in this report tend to fall into overlapping, but different frequency ranges of the acoustic sensitivity curve. This condition may encourage signal designers to vary the frequency content of acoustic deterrence signals in the field. Finally, preliminary observations relating to the tendencies and proclivities of bald eagles to attend to the acoustic landscape lead to the conclusion that eagles monitor their immediate sound environment assiduously. Individuals respond to a variety of natural and synthetic sound signals reliably and, perhaps most relevant in the context of the engineering of acoustic alerting/deterrence technologies, habituation to most sounds considered in this effort was minimal. These preliminary results, while calling for extended behavioral testing, are promising and set the stage for the exportation of behavioral studies into real world scenarios.

17 WIND ENERGY↗

Nondestructive equipment study

Identification of existing nondestructive Evaluation (NDE) methods that could be used in a low Earth orbit environment; evaluation of each method with respect to the set of criteria called out in the statement of work; selection of the most promising NDE methods for further evaluation; use of selected NDE methods to test samples of pressure vessel materials in a vacuum; pressure testing of a complex monolythic pressure vessel with known flaws using acoustic emissions in a vacuum; and recommendations for further studies based on analysis and testing are covered.

Source record↗

The influence of inlet design on the aeroacoustic performance of a JT15D turbofan engine as measured in the NASA-Ames 40 x 80 foot wind tunnel

The influence of inlet design on the aeroacoustic performance of a JT15D turbofan engine was investigated in the NASA-Ames 40 x 80 ft wind tunnel. Four inlet designs representative of those found in commercial service were evaluated at a forward velocity of 80 kn. The inlet designs considered were selected to evaluate the importance of circumferential static pressure distortion (SPD) for a diffusing sound suppressing inlet and throat Mach number (Mth) for a hardwall inlet on the acoustic characteristics of the JT15D engine. Several speed points were studied simulating the operating conditions spanning approach to take-off. Results demonstrated that the dependency of the forward radiated noise on inlet aerodynamic design parameters was significant (about 5 dB) for the range of SPD (0.1-3.0%) and Mth (0.3-0.6) tested. The performance of the bulk absorber acoustic treatment used in the diffusing sound suppressing inlet is also discussed.

Holm, R. G.↗

Noncontact acousto-ultrasonics using laser generation and laser interferometric detection

A compact, portable fiber-optic heterodyne interferometer designed to detect out-of-plane motion on surfaces is described. The interferometer provides a linear output for displacements over a broad frequency range and can be used for ultrasonic, acoustic emission, and acousto-ultrasonic (AU) testing. The interferometer in conjunction with a compact pulsed Nd:YAG laser represents a noncontact testing system. This system was tested to determine its usefulness for the AU technique. The results obtained show that replacement of conventional piezoelectric transducers (PZT) with a laser generation/detection system make it possible to carry out noncontact AU measurements. The waveforms recorded were 5 MHZ PZT-generated ultrasound propagating through an aluminum block, detection of the acoustic emission event, and laser AU waveforms from graphite-epoxy laminates and a filament-wound composite.

Green, Robert E., Jr.↗