Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface conditioning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92

Theoretical and experimental studies of surface processes in the course of molecular-beam epitaxy of gallium nitride

The method of atomic-force microscopy has been used to experimentally study the effect of growth conditions on the structure of the surface of epitaxial GaN layers grown by molecular-beam epitaxy. Quantitative values of the density, height, and width of growth centers in relation to the conditions of epitaxy are obtained; the average length of the diffusion path of particles limiting the GaN growth rate have been estimated; and the activation energies and the surface-diffusion coefficients for these particles have been calculated. The equilibrium composition of adsorbed layers at the GaN (0001) surface in a wide range of deposition temperatures and pressures of gallium and nitrogen has been calculated with account taken of the following components: gallium atoms, nitrogen atoms, and NH molecules. On the basis of the comparison of experimental data on the structure of the GaN surface with results of calculations concerning the composition of adsorbed layers on the growth surface, it was assumed that the growth of GaN layers is limited by supply of gallium.

36 MATERIALS SCIENCE↗

Turbulence in The Marine Boundary Layer and Air Motions Below Stratocumulus Clouds at the ARM Eastern North Atlantic Site

Marine stratocumulus clouds are intimately coupled to the turbulence in the boundary layer and drizzle is known to be ubiquitous within them. Six years of data collected at the Atmospheric Radiation Measurement (ARM)’s Eastern North Atlantic site are utilized to characterize turbulence in the marine boundary layer and air motions below stratocumulus clouds. Profiles of variance of vertical velocity binned by wind direction (wdir) yielded that the boundary layer measurements are affected by the island when the wdir is between 90° and 310° (measured clockwise from North where air is coming from). Data collected during the marine conditions (wdir<90 or wdir>310) showed that the variance of vertical velocity was higher during the winter months than during the summer months due to higher cloudiness, wind speeds, and surface fluxes. Furthermore, during marine conditions the variance of vertical velocity and cloud fraction exhibited a distinct diurnal cycle with higher values during the nighttime than during the daytime. Detailed analysis of 32 cases of drizzling marine stratocumulus clouds showed that for a similar amount of radiative cooling at the cloud top, within the sub-cloud layer 1) drizzle increasingly falls within downdrafts with increasing rain rates, 2) the strength of the downdrafts increases with increasing rain rates, and 3) the correlation between vertical air motion and rain rate is highest in the middle of the sub-cloud layer. The results presented herein have implications for climatological and model evaluation studies conducted at the ENA site, along with efforts of accurately representing drizzle-turbulence interactions in a range of atmospheric models.

54 ENVIRONMENTAL SCIENCES↗

Solution of 3D inverse scattering problems by combined inverse equivalent current and finite element methods

An approach combining boundary integral and finite element methods is introduced for the solution of three-dimensional inverse electromagnetic medium scattering problems. Based on the equivalence principle, unknown equivalent electric and magnetic surface current densities on a closed surface are utilized to decompose the inverse medium problem into two parts: a linear radiation problem and a nonlinear cavity problem. The first problem is formulated by a boundary integral equation, the computational burden of which is reduced by employing the multilevel fast multipole method (MLFMM). Reconstructed Cauchy data on the surface allows the utilization of the Lorentz reciprocity and the Poynting's theorems. Exploiting these theorems, the noise level and an initial guess are estimated for the cavity problem. Moreover, it is possible to determine whether the material is lossy or not. In the second problem, the estimated surface currents form inhomogeneous boundary conditions of the cavity problem. The cavity problem is formulated by the finite element technique and solved iteratively by the Gauss–Newton method to reconstruct the properties of the object. Regularization for both the first and the second problems is achieved by a Krylov subspace method. The proposed method is tested against both synthetic and experimental data and promising reconstruction results are obtained.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

VERTICAL STRUCTURE OF STATIONARY ACCRETION DISKS WITH A LARGE-SCALE MAGNETIC FIELD

In earlier works we pointed out that the disk's surface layers are non-turbulent and thus highly conducting (or non-diffusive) because the hydrodynamic and/or magnetorotational instabilities are suppressed high in the disk where the magnetic and radiation pressures are larger than the plasma thermal pressure. Here, we calculate the vertical profiles of the stationary accretion flows (with radial and azimuthal components), and the profiles of the large-scale, magnetic field taking into account the turbulent viscosity and diffusivity and the fact that the turbulence vanishes at the surface of the disk. Also, here we require that the radial accretion speed be zero at the disk's surface and we assume that the ratio of the turbulent viscosity to the turbulent magnetic diffusivity is of order unity. Thus, at the disk's surface there are three boundary conditions. As a result, for a fixed dimensionless viscosity {alpha}-value, we find that there is a definite relation between the ratio R of the accretion power going into magnetic disk winds to the viscous power dissipation and the midplane plasma-{beta}, which is the ratio of the plasma to magnetic pressure in the disk. For a specific disk model with R of order unity we find that the critical value required for a stationary solution is {beta}{sub c} Almost-Equal-To 2.4r/({alpha}h), where h is the disk's half thickness. For weaker magnetic fields, {beta} > {beta}{sub c}, we argue that the poloidal field will advect outward while for {beta} < {beta}{sub c} it will advect inward. Alternatively, if the disk wind is negligible (R<<1), there are stationary solutions with {beta} >> {beta}{sub c}.

79 ASTRONOMY AND ASTROPHYSICS↗

Tropical continental downdraft characteristics: mesoscale systems versus unorganized convection

Downdrafts and cold pool characteristics for strong mesoscale convective systems (MCSs) and isolated, unorganized deep precipitating convection are analyzed using multi-instrument data from the DOE Atmospheric Radiation Measurement (ARM) GoAmazon2014/5 campaign. Increases in column water vapor (CWV) are observed leading convection, with higher CWV preceding MCSs than for isolated cells. For both MCSs and isolated cells, increases in wind speed, decreases in surface moisture and temperature, and increases in relative humidity occur coincidentally with system passages. Composites of vertical velocity data and radar reflectivity from a radar wind profiler show that the downdrafts associated with the sharpest decreases in surface equivalent potential temperature ( θ e ) have a probability of occurrence that increases with decreasing height below the freezing level. Both MCSs and unorganized convection show similar mean downdraft magnitudes and probabilities with height. Mixing computations suggest that, on average, air originating at heights greater than 3 km must undergo substantial mixing, particularly in the case of isolated cells, to match the observed cold pool θ e , implying a low typical origin level. Precipitation conditionally averaged on decreases in surface equivalent potential temperature (Δ θ e ) exhibits a strong relationship because the most negative Δ θ e values are associated with a high probability of precipitation. The more physically motivated conditional average of Δ θ e on precipitation shows that decreases in θ e level off with increasing precipitation rate, bounded by the maximum difference between surface θ e and its minimum in the profile aloft. In conclusion, robustness of these statistics observed across scales and regions suggests their potential use as model diagnostic tools for the improvement of downdraft parameterizations in climate models.

54 ENVIRONMENTAL SCIENCES↗

Hoop conjecture in spherically symmetric spacetimes

We give general sufficient conditions for the existence of trapped surfaces due to concentration of matter in spherically symmetric initial data sets satisfying the dominant energy condition. These results are novel in that they apply and are meaningful for arbitrary spacelike slices, that is, they do not require any auxiliary assumptions such as maximality, time symmetry, or special extrinsic foliations, and most importantly they can easily be generalized to the nonspherical case once an existence theory for a modified version of the Jang equation is developed. Moreover, our methods also yield positivity and monotonicity properties of the Misner-Sharp energy.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DECOVALEX-2023: Task D Final Report

Task D of DECOVALEX-2023 is focused on the simulation of the coupled thermal hydraulic-mechanical (THM) behaviour in the full-scale engineered barrier system (EBS). The Horonobe EBS experiment is the demonstration of the full-scale EBS in the underground research laboratory (URL) (performed by JAEA in the Horonobe URL in Japan). Task D consisted of the three steps, a preliminary step (Step 0), simulation of the laboratory tests (Step 1) and simulation of the in-situ full-scale EBS experiment (Step 2). Since the Horonobe EBS experiment demonstrates the vertical emplacement option of the EBS, the experiment gallery is also backfilled with the backfill material. Therefore, interaction between the EBS and the backfill material can also be demonstrated, such as deformation (change of density) of the buffer material. The underground water in the Horonobe URL is saline. This fact adds chemical processes to THM behaviour. For example, mechanical properties (such as swelling pressure of the buffer material and backfill material) and hydraulic properties (such as permeability of the buffer material and backfill material) change depending on the water chemistry. Task D was therefore a challenging Task focused on not only the relatively simple THM behaviour but also complex THM behaviour including chemical processes. Six research teams (BGR, CAS, JAEA, KAERI, SNL and Taipower) participated the Task D. BGR, CAS, JAEA, KAERI and Taipower research teams selected a THM approach, while the SNL research team selected a TH approach. Step 1 involved the simulation of laboratory test results and was important to check the numerical codes developed by the research teams. Step 1 was divided into four sub steps. The simulation results through the Step 1 identified the parameters for simulation of the Step 2. Basic parameters of the materials (buffer material, backfill material, rock mass, concrete, sand) were provided by JAEA. Special parameters which research team needed were identified by back analysis of Step 1. Most notably the mechanical behaviour of swelling and displacement depended on the applied model (elastic model or elastoplastic model). Parameters such as Young’s modulus were found to need smaller values than characterised in the fundamental laboratory test results (Step 1-1, 1-2) for the elastic model. Although laboratory experiments are usually simple, test results contained some error. For example, if the saturation level is 100 % or higher, it should be considered an error. This situation was presented in the Step 1-3. A possible reason is that the buffer material is a mixture of bentonite and silica sand. When a specimen is cut to measure volume or weight, sand grains will affect the measurement data. In Step 2, boundary conditions such as temperature on the surface of the simulated overpack, heater power of the electrical heaters installed in the simulated overpack, injection pressure and inflow rate of the test water, were applied. The outer boundary conditions can be selected using measured data (injection pressure and inflow rate of the test water that is controlled by the injection systems installed in the sand layer around the buffer material and in the boundary between backfill material and concrete support). Since such measured data has some noise, research teams developed their own simplified boundary conditions. Inner boundary conditions can be selected using measured data as heater power and temperature on the surface of the simulated overpack. These data also contain some noise, so research teams developed their own simplified developed boundary conditions. Task D validated various approaches thorough the simulation of the in-situ full scale EBS system including backfill of the gallery: variations in the coupling processes (THM or THC), analysis codes, and boundary conditions. Temperature distribution in the buffer material was simulated well by all research teams. This means thermal behaviour is not sensitive to the simulation approaches. Although the water content distribution on the outside of the buffer material was well simulated by all research teams, the simulation results differ from the measured values inside the buffer material (at the centre and inside, near the simulated overpack). The buffer material is made from tap water, but in the in-situ experiment, saline groundwater infiltrates the buffer material. Therefore, the selection of the hydraulic parameters of the buffer material greatly affects the simulation results of the re saturation behaviour of the buffer material. In the Horonobe EBS experiment, measured values suitable for validating the simulation results were not obtained near the simulated overpack. When simulating the pressure and deformation of the buffer material, the measurement data is easily affected by the installation conditions of the measurement sensors, so verifying the measurement data itself remains an issue. Mechanical simulation results differ depending on whether they are considered as elastic or elastoplastic phenomena. The accuracy of measured in-situ data can be assessed by detailed analysis comparing sampling specimen analysis and measured data. The Horonobe EBS experiment is scheduled to be dismantled in the future (FY2026 and 2027). This detailed dismantling investigation will finally confirm the measured data.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Experimental study of laser-oxygen cutting of low-carbon steel using fibre and CO{sub 2} lasers under conditions of minimal roughness

The results of an experimental study of laser-oxygen cutting of low-carbon steel using fibre and CO{sub 2} lasers are generalised. The dependence of roughness of the cut surface on the cutting parameters is investigated, and the conditions under which the surface roughness is minimal are formulated. It is shown that for both types of lasers these conditions can be expressed in the same way in terms of the dimensionless variables – the Péclet number Pe and the output power Q of laser radiation per unit thickness of the cut sheet – and take the form of the similarity laws: Pe = const, Q = const. The optimal values of Pe and Q are found. We have derived empirical expressions that relate the laser power and cutting speed with the thickness of the cut sheet under the condition of minimal roughness in the case of cutting by means of radiation from fibre and CO{sub 2} lasers. (laser technologies)

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A study on the surface severe plastic deformation behavior of a Zr-based bulk metallic glass (BMG)

A surface treatment process, which can generate the severe plastic deformation in the near-surface layer of crystalline materials, is successfully applied on the Zr{sub 50}Cu{sub 40}Al{sub 10} bulk metallic glass (BMG). The experiment is implemented using 20 WC/Co balls with a velocity of about 5 m/s to bombard the surface of the samples in a purified argon atmosphere. The plastic-flow deformation in the unconstrained sample edge was observed, which exhibits the good intrinsic ductility of this material under the experimental condition. In the sub-surface layer, the bombardment-induced shear-band operations generate the extrusion and intrusion marks on the side face. Differential scanning calorimetry (DSC) shows that the free volumes of the deformed BMG have increased, and possible crystallization may occur during the process. X-ray diffraction (XRD) and synchrotron high-energy X-ray diffraction techniques were used to inspect the possible crystal phase. A nanoindentation test shows that on the side surface, the hardness increases and, then, decreases with the distance from the processed surface. Four-point-bending-fatigue behavior has been studied and related to the modified surface structure and the compressive residual stress introduced by the surface treatment.

43 PARTICLE ACCELERATORS↗

Anti-adhesive characteristics of CHF{sub 3}/O{sub 2} and C{sub 4}F{sub 8}/O{sub 2} plasma-modified silicon molds for nanoimprint lithography

The anti-adhesive characteristics of a plasma-modified silicon mold surface for nanoimprint lithography are presented. Both CHF{sub 3}/O{sub 2} and C{sub 4}F{sub 8}/O{sub 2} plasma were used to form an anti-adhesive layer on silicon mold surfaces. The gas mixing ratios of CHF{sub 3}/O{sub 2} and C{sub 4}F{sub 8}/O{sub 2} were experimentally changed between 0% and 80% to optimize the plasma conditions to obtain a low surface energy of the silicon mold. The plasma characteristics were examined by optical emission spectroscopy (OES). In order to investigate the changes in surface energy and surface chemistry of the anti-adhesive layer during repeated demolding cycles, contact angle measurements and X-ray photoelectron spectroscopy (XPS) were performed on the plasma-modified silicon mold surface. Simultaneously, the surface morphology of the demolded resists was evaluated by field-emission scanning electron microscope (FE-SEM) in order to examine the effect of the anti-adhesive layers on the duplicated patterns of the resists. It was observed that the anti-adhesive layer formed by CHF{sub 3}/O{sub 2} plasma treatment was worn out more easily during repeated demolding cycles than the film formed by C{sub 4}F{sub 8}/O{sub 2} plasma treatment, because CHF{sub 3}/O{sub 2} gas plasma formed a thinner plasma-polymerized film over the same plasma treatment time.

36 MATERIALS SCIENCE↗

Mechanism and energetics of O and O{sub 2} adsorption on polar and non-polar ZnO surfaces

Polar surfaces of semiconducting metal oxides can exhibit structures and chemical reactivities that are distinct from their non-polar surfaces. Using first-principles calculations, we examine O adatom and O{sub 2} molecule adsorption on 8 different known ZnO reconstructions including Zn-terminated (Zn–ZnO) and O-terminated (O–ZnO) polar surfaces, and non-polar surfaces. We find that adsorption tendencies are largely governed by the thermodynamic environment, but exhibit variations due to the different surface chemistries of various reconstructions. The Zn–ZnO surface reconstructions which appear under O-rich and H-poor environments are found to be most amenable to O and O{sub 2} adsorption. We attribute this to the fact that on Zn–ZnO, the O-rich environments that promote O adsorption also simultaneously favor reconstructions that involve adsorbed O species. On these Zn–ZnO surfaces, O{sub 2} dissociatively adsorbs to form O adatoms. By contrast, on O–ZnO surfaces, the O-rich conditions required for O or O{sub 2} adsorption tend to promote reconstructions involving adsorbed H species, making further O species adsorption more difficult. These insights about O{sub 2} adsorption on ZnO surfaces suggest possible design rules to understand the adsorption properties of semiconductor polar surfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Dynamic critical behavior of model A in films: Zero-mode boundary conditions and expansion near four dimensions

The critical dynamics of relaxational stochastic models with nonconserved n-component order parameter {phi} and no coupling to other slow variables ('model A') is investigated in film geometries for the cases of periodic and free boundary conditions. The Hamiltonian H governing the stationary equilibrium distribution is taken to be O(n) symmetric and to involve, in the case of free boundary conditions, the boundary terms B{sub j}c{sub j}{phi}{sup 2}/2 associated with the two confining surface planes B{sub j}, j=1,2, at z=0 and z=L. Both enhancement variables c{sub j} are presumed to be subcritical or critical, so that no long-range surface order can occur above the bulk critical temperature T{sub c,{infinity}}. A field-theoretic renormalization-group study of the dynamic critical behavior at d=4-{epsilon} bulk dimensions is presented, with special attention paid to the cases where the classical theories involve zero modes at T{sub c,{infinity}}. This applies when either both c{sub j} take the critical value c{sub sp} associated with the special surface transition or else periodic boundary conditions are imposed. Owing to the zero modes, the {epsilon} expansion becomes ill-defined at T{sub c,{infinity}}. Analogously to the static case, the field theory can be reorganized to obtain a well-defined small-{epsilon} expansion involving half-integer powers of {epsilon}, modulated by powers of ln {epsilon}. This is achieved through the construction of an effective (d-1)-dimensional action for the zero-mode component of the order parameter by integrating out its orthogonal component via renormalization-group improved perturbation theory. Explicit results for the scaling functions of temperature-dependent finite-size susceptibilities at temperatures T{>=}T{sub c,{infinity}} and of layer and surface susceptibilities at the bulk critical point are given to orders {epsilon} and {epsilon}{sup 3/2}, respectively. They show that L dependent shifts of the multicritical special point occur along the temperature and enhancement axes. For the case of periodic boundary conditions, the consistency of the expansions to O({epsilon}{sup 3/2}) with exact large-n results is shown. We also discuss briefly the effects of weak anisotropy, relating theories whose Hamiltonian involves a generalized square gradient term B{sup kl}{partial_derivative}{sub k}{phi}{center_dot}{partial_derivative}{sub l}{phi} to those with a conventional ({nabla}{phi}){sup 2} term.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

On the surface passivating principle of functional thiol towards efficient and stable perovskite nanocrystal solar cells

Inorganic halide perovskite nanocrystals (PNCs) have demonstrated promising potential for solar cell applications. However, the lability of photoactive CsPbI3 phase under ambient conditions, coupled with considerable amounts of surface defects induced during solidification process, have impeded achieving high performances and longevities of the PNC-based solar cells. Post-treatment of the PNCs with organic ligands has been proposed as an efficient strategy for surface passivation, which, however, still relies on the binding actions of typical functional groups towards surface defects (especially, carboxylates onto iodine vacancies). Herein, we uncover that thiolate, a deprotonated form of thiol, renders distinctive binding feasibility towards iodine vacancies at the CsPbI3 PNC surface, compared with those of typical functional groups. By treating the PNC solid with deprotonated cysteine as a ligand, the surface defects are comprehensively passivated. The solar cells with the modified PNC films demonstrate an excellent PCE of 15.5 % and improved device longevity (77 % of initial PCE over 2 months) under ambient conditions. Our work not only elucidates the chemical principles of thiol on the binding with PNC surface, but also corroborates the power of thiolate as a promising strategy to develop high performances and improved longevity of solar cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Imaging the condensation and evaporation of molecularly thin ethanol films with surface forces apparatus

A new method for imaging condensation and evaporation of molecularly thin ethanol films is reported. It is found that the first adsorbed layer of ethanol film on mica surface behaves as solid like structure that cannot flow freely. With the increase of exposure time, more ethanol molecules condense over the mica surface in the saturated ethanol vapor condition. The first layer of adsorbed ethanol film is about 3.8 Å thick measured from the surface forces apparatus, which is believed to be the average diameter of ethanol molecules while they are confined in between two atomically smooth mica surfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The structure and properties of boron carbide ceramics modified by high-current pulsed electron-beam

The present work is devoted to numerical simulation of temperature fields and the analysis of structural and strength properties of the samples surface layer of boron carbide ceramics treated by the high-current pulsed electron-beam of the submillisecond duration. The samples made of sintered boron carbide ceramics are used in these investigations. The problem of calculating the temperature field is reduced to solving the thermal conductivity equation. The electron beam density ranges between 8…30 J/cm{sup 2}, while the pulse durations are 100…200 μs in numerical modelling. The results of modelling the temperature field allowed ascertaining the threshold parameters of the electron beam, such as energy density and pulse duration. The electron beam irradiation is accompanied by the structural modification of the surface layer of boron carbide ceramics either in the single-phase (liquid or solid) or two-phase (solid-liquid) states. The sample surface of boron carbide ceramics is treated under the two-phase state (solid-liquid) conditions of the structural modification. The surface layer is modified by the high-current pulsed electron-beam produced by SOLO installation at the Institute of High Current Electronics of the Siberian Branch of the Russian Academy of Sciences, Tomsk, Russia. The elemental composition and the defect structure of the modified surface layer are analyzed by the optical instrument, scanning electron and transmission electron microscopes. Mechanical properties of the modified layer are determined measuring its hardness and crack resistance. Research results show that the melting and subsequent rapid solidification of the surface layer lead to such phenomena as fragmentation due to a crack network, grain size reduction, formation of the sub-grained structure due to mechanical twinning, and increase of hardness and crack resistance.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Fiber-based adsorbents having high adsorption capacities for recovering dissolved metals and methods thereof

A fiber-based adsorbent and a related method of manufacture are provided. The fiber-based adsorbent includes polymer fibers with grafted side chains and an increased surface area per unit weight over known fibers to increase the adsorption of dissolved metals, for example uranium, from aqueous solutions. The polymer fibers include a circular morphology in some embodiments, having a mean diameter of less than 15 microns, optionally less than about 1 micron. In other embodiments, the polymer fibers include a non-circular morphology, optionally defining multiple gear-shaped, winged-shaped or lobe-shaped projections along the length of the polymer fibers. A method for forming the fiber-based adsorbents includes irradiating high surface area polymer fibers, grafting with polymerizable reactive monomers, reacting the grafted fibers with hydroxylamine, and conditioning with an alkaline solution. High surface area fiber-based adsorbents formed according to the present method demonstrated a significantly improved uranium adsorption capacity per unit weight over existing adsorbents.

36 MATERIALS SCIENCE↗

Fiber-based adsorbents having high adsorption capacities for recovering dissolved metals and methods thereof

A fiber-based adsorbent and a related method of manufacture are provided. The fiber-based adsorbent includes polymer fibers with grafted side chains and an increased surface area per unit weight over known fibers to increase the adsorption of dissolved metals, for example uranium, from aqueous solutions. The polymer fibers include a circular morphology in some embodiments, having a mean diameter of less than 15 microns, optionally less than about 1 micron. In other embodiments, the polymer fibers include a non-circular morphology, optionally defining multiple gear-shaped, winged-shaped or lobe-shaped projections along the length of the polymer fibers. A method for forming the fiber-based adsorbents includes irradiating high surface area polymer fibers, grafting with polymerizable reactive monomers, reacting the grafted fibers with hydroxylamine, and conditioning with an alkaline solution. High surface area fiber-based adsorbents formed according to the present method demonstrated a significantly improved uranium adsorption capacity per unit weight over existing adsorbents.

36 MATERIALS SCIENCE↗

MAGNETO-FRICTIONAL MODELING OF CORONAL NONLINEAR FORCE-FREE FIELDS. I. TESTING WITH ANALYTIC SOLUTIONS

We report our implementation of the magneto-frictional method in the Message Passing Interface Adaptive Mesh Refinement Versatile Advection Code (MPI-AMRVAC). The method aims at applications where local adaptive mesh refinement (AMR) is essential to make follow-up dynamical modeling affordable. We quantify its performance in both domain-decomposed uniform grids and block-adaptive AMR computations, using all frequently employed force-free, divergence-free, and other vector comparison metrics. As test cases, we revisit the semi-analytic solution of Low and Lou in both Cartesian and spherical geometries, along with the topologically challenging Titov–Démoulin model. We compare different combinations of spatial and temporal discretizations, and find that the fourth-order central difference with a local Lax–Friedrichs dissipation term in a single-step marching scheme is an optimal combination. The initial condition is provided by the potential field, which is the potential field source surface model in spherical geometry. Various boundary conditions are adopted, ranging from fully prescribed cases where all boundaries are assigned with the semi-analytic models, to solar-like cases where only the magnetic field at the bottom is known. Our results demonstrate that all the metrics compare favorably to previous works in both Cartesian and spherical coordinates. Cases with several AMR levels perform in accordance with their effective resolutions. The magneto-frictional method in MPI-AMRVAC allows us to model a region of interest with high spatial resolution and large field of view simultaneously, as required by observation-constrained extrapolations using vector data provided with modern instruments. The applications of the magneto-frictional method to observations are shown in an accompanying paper.

79 ASTRONOMY AND ASTROPHYSICS↗