Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “optimized”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Constrained optimal ascent-flyback shuttle trajectories.

An optimal Space Shuttle ascent-flyback trajectory shaping capability is presented which is based on the accelerated gradient parameter optimization technique. A typical atmospheric flight branched optimization problem is analyzed which required the determination of 31 parameters. This parameter set includes the description of the vehicle attitude control angles for three branches of Shuttle flight: first stage ascent, second stage ascent, and first stage flyback. The important in-flight inequality constraints required to maintain the integrity of the vehicle are considered. Results indicate that for a launch into a 55 deg inclined ellipse, a 13% increase in payload can be realized by using optimal control in the first-stage ascent rather than the conventional gravity-turn steering.

Kamm, J. L.↗
NASA NTRS1973

An historical survey of computational methods in optimal control.

Review of some of the salient theoretical developments in the specific area of optimal control algorithms. The first algorithms for optimal control were aimed at unconstrained problems and were derived by using first- and second-variation methods of the calculus of variations. These methods have subsequently been recognized as gradient, Newton-Raphson, or Gauss-Newton methods in function space. A much more recent addition to the arsenal of unconstrained optimal control algorithms are several variations of conjugate-gradient methods. At first, constrained optimal control problems could only be solved by exterior penalty function methods. Later algorithms specifically designed for constrained problems have appeared. Among these are methods for solving the unconstrained linear quadratic regulator problem, as well as certain constrained minimum-time and minimum-energy problems. Differential-dynamic programming was developed from dynamic programming considerations. The conditional-gradient method, the gradient-projection method, and a couple of feasible directions methods were obtained as extensions or adaptations of related algorithms for finite-dimensional problems. Finally, the so-called epsilon-methods combine the Ritz method with penalty function techniques.

Polak, E.↗
NASA NTRS1973

Optimization of self-acting herringbone journal bearing for maximum stability

Groove parameters were determined to maximize the stability of herringbone grooved journal bearings. Parameters optimized were groove depth, width, length, and angle. Optimization was performed using a small eccentricity, infinite groove analysis in conjunction with: (1) a previously developed Newton-Raphson procedure for bearings with the smooth member rotating or with the grooved member rotating at low compressibility numbers, and (2) a newly-developed vector technique for bearings with the grooved member rotating at high compressibility numbers. The design curves enable one to choose the optimum bearing for a wide range of operating conditions. These include: (1) compressibility numbers from 0 (incompressible) to 80, (2) length to diameter ratios from 1/4 to 2, and (3) smooth or grooved member rotating. Compared to bearings optimized to maximize load capacity, bearings optimized for stability: (1) allow a thousandfold increase in bearing-supported mass in some cases before onset of instability (the most dramatic increase are for bearings with small L/D operating at high compressibility numbers), and (2) lose no more than 77-percent of their load capacity in any case studied. Stability is much greater when the grooved member rotates.

Fleming, D. P.↗
NASA NTRS1973

Techniques for shuttle trajectory optimization

The application of recently developed function-space Davidon-type techniques to the shuttle ascent trajectory optimization problem is discussed along with an investigation of the recently developed PRAXIS algorithm for parameter optimization. At the outset of this analysis, the major deficiency of the function-space algorithms was their potential storage problems. Since most previous analyses of the methods were with relatively low-dimension problems, no storage problems were encountered. However, in shuttle trajectory optimization, storage is a problem, and this problem was handled efficiently. Topics discussed include: the shuttle ascent model and the development of the particular optimization equations; the function-space algorithms; the operation of the algorithm and typical simulations; variable final-time problem considerations; and a modification of Powell's algorithm.

Edge, E. R.↗
NASA NTRS1973

Some optimal considerations in attitude control systems

The conventional six-engine reaction control jet relay attitude control law with deadband is shown to be a good linear approximation to a weighted time-fuel optimal control law. Techniques for evaluating the value of the relative weighting between time and fuel for a particular relay control law is studied along with techniques to interrelate other parameters for the two control laws. Vehicle attitude control laws employing control moment gyros are then investigated. Steering laws obtained from the expression for the reaction torque of the gyro configuration are compared to a total optimal attitude control law that is derived from optimal linear regulator theory. This total optimal attitude control law has computational disadvantages in the solving of the matrix Riccati equation. Several computational algorithms for solving the matrix Riccati equation are investigated with respect to accuracy, computational storage requirements, and computational speed.

Boland, J. S., III↗
NASA NTRS1973

Four-body trajectory optimization

A collection of typical three-body trajectories from the L1 libration point on the sun-earth line to the earth is presented. These trajectories in the sun-earth system are grouped into four distinct families which differ in transfer time and delta V requirements. Curves showing the variations of delta V with respect to transfer time, and typical two and three-impulse primer vector histories, are included. The development of a four-body trajectory optimization program to compute fuel optimal trajectories between the earth and a point in the sun-earth-moon system are also discussed. Methods for generating fuel optimal two-impulse trajectories which originate at the earth or a point in space, and fuel optimal three-impulse trajectories between two points in space, are presented. A brief qualitative comparison of these methods is given. An example of a four-body two-impulse transfer from the Li libration point to the earth is included.

Pu, C. L.↗
NASA NTRS1974

Optimal compensator structure for linear time-invariant plant with inaccessible states

The problem is considered of designing an optimal linear time-invariant dynamic compensator for the regulation of an n-th order linear time-invariant plant with m independent outputs. The initial plant state is characterized by its first and second moments, and the cost is usual quadratic infinite-time penalty on the state and control, averaged over the initial plant and compensator states. The compensator is based on a minimal-order Luenberger observer and consequently has fixed dimension n-m. Necessary and sufficient conditions are derived for optimality of the compensator gains. The optimal compensator is shown to be unique if the plant has a particular canonical form, and, in general, for any arbitrary plant, the class of all optimal compensators is precisely determined.

Blanvillain, P. J. P.↗
NASA NTRS1974

Optimization of self-acting herringbone-grooved journal bearings for maximum stability

Groove parameters were determined to maximize the stability of herringbone-grooved journal bearings. Parameters optimized were groove depth, width, length, and angle. Optimization was performed by using a small-eccentricity, infinite-groove analysis in conjunction with a previously developed Newton-Raphson procedure for bearings with the smooth member rotating or with the grooved member rotating at low compressibility numbers, and a newly developed vector technique for bearings with the grooved member rotating at high compressibility numbers. The design curves in this report enable one to choose the optimum bearing for a wide range of operating conditions. Compared with bearings optimized to maximize load capacity, bearings optimized for stability allow a thousandfold increase in bearing-supported mass in some cases before onset of instability, and lose no more than 77 percent of their load capacity in any case studied. Stability is much greater when the grooved member rotates.

Fleming, D. P.↗
NASA NTRS1974

Optimization of self-acting herringbone journal bearings for maximum stability

Groove parameters were determined to maximize the stability of herringbone grooved journal bearings. Parameters optimized were groove depth, width, length, and angle. Optimization was performed using a small eccentricity, infinite groove analysis in conjunction with: (1) a previously developed Newton-Raphson procedure for bearings with the smooth member rotating or with the grooved member rotating at low compressibility numbers; (2) a newly-developed vector technique for bearings with the grooved member rotating at high compressibility numbers. The design curves in this report enable one to choose the optimum bearing for a wide range of operating conditions. These include: (1) compressibility numbers from 0 to 80; (2) length to diameter ratios from 1/4 to 2; and (3) smooth or grooved member rotating. Compared to bearings optimized to maximize load capacity, bearings optimized for stability allow a thousandfold increase in bearing-supported mass in some cases before onset of instability. Stability is much greater when the grooved member rotates.

Fleming, D. P.↗
NASA NTRS1974

Optimization of self-acting herringbone journal bearings for maximum stability

The stability of herringbone grooved journal bearings was increased by optimizing the groove depth, width, length, and angle. Optimization was performed on the basis of a small-eccentricity infinite-groove analysis in combination with a previously developed Newton-Raphson procedure for bearings with the smooth member rotating or with the grooved member rotating at low compressibility numbers. A newly-developed vector technique for bearings with the grooved member rotating at high compressibility numbers also was used in the analysis. The design curves obtained are suitable for choosing the optimum bearing for a wide range of operating conditions (compressibility numbers from 0 to 80, length to diameter ratios from 1/4 to 2, and smooth or grooved member rotating). Compared to bearings optimized for maximum load, bearings optimized for maximum stability are shown to provide a drastic increase in bearing-supported mass. Bearings with grooved member rotating are substantially more stable than bearing with smooth member rotating, particularly at high compressibility numbers.

Fleming, D. P.↗
NASA NTRS1976

Optimality study of a gust alleviation system for light wing-loading STOL aircraft

An analytical study was made of an optimal gust alleviation system that employs a vertical gust sensor mounted forward of an aircraft's center of gravity. Frequency domain optimization techniques were employed to synthesize the optimal filters that process the corrective signals to the flaps and elevator actuators. Special attention was given to evaluating the effectiveness of lead time, that is, the time by which relative wind sensor information should lead the actual encounter of the gust. The resulting filter is expressed as an implicit function of the prescribed control cost. A numerical example for a light wing loading STOL aircraft is included in which the optimal trade-off between performance and control cost is systematically studied.

Komoda, M.↗
NASA NTRS1976

A method for generating numerical pilot opinion ratings using the optimal pilot model

A method for generating numerical pilot opinion ratings using the optimal pilot model is introduced. The method is contained in a rating hypothesis which states that the numerical rating which a human pilot assigns to a specific vehicle and task can be directly related to the numerical value of the index of performance resulting from the optimal pilot modeling procedure as applied to that vehicle and task. The hypothesis is tested using the data from four piloted simulations. The results indicate that the hypothesis is reasonable, but that the predictive capability of the method is a strong function of the accuracy of the pilot model itself. This accuracy is, in turn, dependent upon the parameters which define the optimal modeling problem. A procedure for specifying the parameters for the optimal pilot model in the absence of experimental data is suggested.

Hess, R. A.↗
NASA NTRS1976

Design analogy between optimal time-fuel and rate-ledge relay controllers

An empirically obtained reaction control jet relay control law with deadband is used as the basis for determining an equivalent weighted time-fuel optimal switching curve according to a least-squares criterion. The derived transformation from the empirical to the optimal law is found to be reversible and to yield a unique transformed control law. The proposed method provides a basis for determining the behavior of an easily implemented relay control law using well-known optimal control results, as well as determining the equivalent relay law corresponding to an analytically determined optimal control law. A numerical example illustrates the transformation technique and simulation results are presented to compare the two control laws.

White, L. R.↗
NASA NTRS1976

Computational alternatives to obtain time optimal jet engine control

Two computational methods to determine an open loop time optimal control sequence for a simple single spool turbojet engine are described by a set of nonlinear differential equations. Both methods are modifications of widely accepted algorithms which can solve fixed time unconstrained optimal control problems with a free right end. Constrained problems to be considered have fixed right ends and free time. Dynamic programming is defined on a standard problem and it yields a successive approximation solution to the time optimal problem of interest. A feedback control law is obtained and it is then used to determine the corresponding open loop control sequence. The Fletcher-Reeves conjugate gradient method has been selected for adaptation to solve a nonlinear optimal control problem with state variable and control constraints.

Basso, R. J.↗
NASA NTRS1976

Optimal one-section and two-section circular sound-absorbing duct liners for plane-wave and monopole sources without flow

A discrete frequency study is made of the influence of source characteristics on the optimal properties of acoustically lined uniform and two section ducts. Two simplified sources, a plane wave and a monopole, are considered in some detail and over a greater frequency range than has been previously studied. Source and termination impedance effects are given limited examination. An example of a turbomachinery source and three associated source variants is also presented. Optimal liner designs based on modal theory approach the Cremer criterion at low frequencies and the geometric acoustics limit at high frequencies. Over an intermediate frequency range, optimal two section liners produced higher transmission losses than did the uniform configurations. Source distribution effects were found to have a significant effect on optimal liner design, but source and termination impedance effects appear to be relatively unimportant.

Lester, H. C.↗
NASA NTRS1977

Helicopter optimal descent and landing after power loss

An optimal control solution is obtained for the descent and landing of a helicopter after the loss of power in level flight. The model considers the helicopter vertical velocity, horizontal velocity, and rotor speed; and it includes representations of ground effect, rotor inflow time lag, pilot reaction time, rotor stall, and the induced velocity curve in the vortex ring state. The control (rotor thrust magnitude and direction) required to minimize the vertical and horizontal velocity at contact with the ground is obtained using nonlinear optimal control theory. It is found that the optimal descent after power loss in hover is a purely vertical flight path. Good correlation, even quantitatively, is found between the calculations and (non-optimal) flight test results.

Johnson, W.↗
NASA NTRS1976

Trajectory optimization for the Atlas/Centaur launch vehicle

A state-of-art survey of computational techniques employed in design and optimization of trajectories for the Atlas/Centaur launch vehicle is presented. Attention is focused on the constrained optimization technique, related to Hestenes' (1969) method of multipliers, with various formulas used in updating the multipliers. Advantages of applying multiplier method to trajectory optimization, with gains in computing speed, are argued, and optimization of the HEAO-A (high energy astronomical observatory) is discussed. Open-loop atmospheric guidance strategy and closed-loop exoatmospheric pitch and yaw guidance equations are dealt with, and the full range of constraints to be observed during the flight is discussed.

Brusch, R. G.↗
NASA NTRS1976

Numerical optimization of gasdynamic lasers

A sophisticated numerical optimization procedure has been coupled to a detailed theoretical model of the carbon dioxide gasdynamic laser (GDL) for the purpose of systematically evaluating the performance of these systems. The integrated model was used to predict the performance of a wide variety of combustion-driven gasdynamic lasers and was then used to maximize the theoretical available specific energy of these lasers. Up to six design variables and three nonlinear constraints were used in these optimizations, although the method is not limited to this number. Results are presented to show the performance of typical lasers before and after optimization. Improvements approaching a factor of two in the available specific energy are found, suggesting that numerical optimization techniques are valuable in improving the design of gasdynamic lasers.

Saunders, R. C., III↗