Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “load shapes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92

An experimental investigation of delamination buckling and growth

An experimental investigation of delamination buckling and growth in compression loaded composite laminates is described. Compression tests were conducted on impact damaged laminates and laminates containing preimplanted delaminations. These tests were performed utilizing a fixture designed to prevent global buckling. The results of this study indicate that considerations in addition to initial defect geometry influence the shape of the boundary of the buckled region. Further, idealized delamination buckling from preimplanted delaminations may occur quite differently than in the case of an impact damaged laminate. The growth of a delamination following buckling may follow an irregular path and may involve the delamination growing into different interfaces.

Davidson, Barry D.↗

Transverse Stress Decay in a Specially Orthotropic Strip Under Localizing Normal Edge Loading

Solutions are presented for the stresses in a specially orthotropic infinite strip which is subjected to localized uniform normal loading on one edge while the other edge is either restrained against normal displacement only, or completely fixed. The solutions are used to investigate the diffusion of load into the strip and in particular the decay of normal stress across the width of the strip. For orthotropic strips representative of a broad range of balanced and symmetric angle-ply composite laminates, minimum strip widths are found that ensure at least 90% decay of the normal stress across the strip. In addition, in a few cases where, on the fixed edge the peak shear stress exceeds the normal stress in magnitude, minimum strip widths that ensure 90% decay of both stresses are found. To help in putting these results into perspective, and to illustrate the influence of material properties on load 9 orthotropic materials, closed-form solutions for the stresses in similarly loaded orthotropic half-planes are obtained. These solutions are used to generate illustrative stress contour plots for several representative laminates. Among the laminates, those composed of intermediate-angle plies, i.e., from about 30 degrees to 60 degrees, exhibit marked changes in normal stress contour shape with stress level. The stress contours are also used to find 90% decay distances in the half-planes. In all cases, the minimum strip widths for 90% decay of the normal stress exceed the 90% decay distances in the corresponding half-planes, in amounts ranging from only a few percent to about 50% of the half-plane decay distances. The 90% decay distances depend on both material properties and the boundary conditions on the supported edge.

Fichter, W. B.↗

Technologies Involved in Configuring an Advanced Earth-to-Orbit Transport for Low Structural Mass

The current space shuttle is expected to adequately meet Government and industry needs for the transport of cargo to and from orbit well into the 1990's. However, continual study of potential follow-on shuttle systems is necessary and desirable in order to complement ongoing research in materials, structures, propulsion, aerodynamics, and other related areas. By studying alternate systems well in advance, it will be possible to explore the various technologies and develop those for which there is the greatest apparent payoff. In this paper a single-stage Earth-to-orbit transport designed for delivery of approximately 29,500 kg (65,000 lb) payload will be described. The vehicle, which takes off vertically and lands horizontally, is 60 m (197 feet) long and weighs approximately 1.8 Gg (4 M lb) at liftoff. In the interest of weight reduction, a simple body of revolution is utilized for the main body shell. In this design the main propulsion tanks serve as a primary load-carrying structure. Further, in order to minimize structural mass, the cargo bay is located between two of the main propellant tanks. The cargo volume, at 396 cu m (14,000 cu feet), exceeds that provided by the shuttle; but the bay itself is nonconforming in shape - being approximately 10 m (32 feet) in diameter by 5 m (17 feet) long. Dual-fuel propulsion is employed, since a number of studies have shown that (though lowering performance) the operation of hydrocarbon (RP) engines in parallel with LOX/LH2 engines results in a net reduction in the vehicle's physical size and structural mass. Other weight-saving features entail the extensive use of honeycomb sandwiches, advanced materials, and advanced fabrication techniques. The vehicle presented is utilized only as a means to study and identify various technologies needed in order to develop a low mass Earth-to-orbit transportation system for the future. The conclusion of this study is that vehicle geometry and structural/materials technology are critical to the development of efficient single-stage Earth-to-orbit transports.

MacConochie, Ian O.↗

Modeling and Optimization for Morphing Wing Concept Generation II: Morphing Wing Modeling and Structural Sizing Techniques - Part 1

This report documents a series of investigations to develop an approach for structural sizing of various morphing wing concepts. For the purposes of this report, a morphing wing is one whose planform can make significant shape changes in flight - increasing wing area by 50% or more from the lowest possible area, changing sweep 30 or more, and / or increasing aspect ratio by as much as 200% from the lowest possible value. These significant changes in geometry mean that the underlying load-bearing structure changes geometry. While most finite element analysis packages provide some sort of structural optimization capability, these codes are not amenable to making significant changes in the stiffness matrix to reflect the large morphing wing planform changes. The investigations presented here use a finite element code capable of aeroelastic analysis in three different optimization approaches -a "simultaneous analysis" approach, a "sequential" approach, and an "aggregate" approach.

Skillen, Michael D.↗

Overview: Performance Adaptive Aeroelastic Wing

An overview of recent aeroelasitc wing-shaping work at the NASA Ames Research Center is presented. The highlight focuses on activity related to the Performance Adaptive Aeroelastic Wing concept and related Variable Camber Continuous Trailing Edge Flap actuation system. Topics covered include drag-reducing configurations and online algorithms, gust and maneuver load techniques, and wind tunnel demonstrations.

Hashemi, Kelley↗

Overgeneration from Solar Energy in California - A Field Guide to the Duck Chart

In 2013, the California Independent System Operator published the "duck chart,"" which shows a significant drop in mid-day net load on a spring day as solar photovoltaics (PV) are added to the system. The chart raises concerns that the conventional power system will be unable to accommodate the ramp rate and range needed to fully utilize solar energy, particularly on days characterized by the duck shape. This could result in "overgeneration"" and curtailed renewable energy, increasing its costs and reducing its environmental benefits. This paper explores the duck chart in detail, examining how much PV might need to be curtailed if additional grid flexibility measures are not taken, and how curtailment rates can be decreased by changing grid operational practices. It finds that under business-as-usual types of assumptions and corresponding levels of grid flexibility in California, solar penetrations as low as 20 percent of annual energy could lead to marginal curtailment rates that exceed 30 percent. However, by allowing (or requiring) distributed PV and storage (including new installations that are part of the California storage mandate) to provide grid services, system flexibility could be greatly enhanced. Doing so could significantly reduce curtailment and allow much greater penetration of variable generation resources in achieving a 50 percent renewable portfolio standard. Overall, the work described in this paper points to the need to fully integrate distributed resources into grid system planning and operations to allow maximum use of the solar resource.

14 SOLAR ENERGY↗

The Science and Engineering of Durable Ultralow PGM Catalysts (2012 DOE-EERE-FCT Annual Progress Report)

Minimizing the quantity of Pt group metals used in polymer membrane fuel cells (PEMFCs) is one of the remaining grand challenges for fuel cell commercialization. Tremendous progress has been achieved over the last two decades in decreasing the Pt loading required for efficient fuel cell performance. Unfortunately, the fluctuations in the price of Pt represent a substantial barrier to the economics of widespread fuel cell use. Durability and impurity tolerance are also challenges that are tightly coupled to fuel cell Pt electrode loading. Traditional approaches to decreasing the amount of Pt required for good performance include: (1) Increasing mass activity by decreasing Pt particle size by supporting on carbon; (2) Alloy formulation Pt-Co, Pt-Cr alloys to improve mass activity; (3) Increasing Pt utilization by optimization of electronic and ionic contact of the Pt particles; (4) Improving conductivity of the electronic and ionic conducting constituents of the membrane electrode assembly; and (5) Improving reactant to and product mass transport away from the electroactive sites. Recent novel approaches include the nanoengineering of core shell catalysts and Pt particles of unusual geometries such as nanowires/whiskers. The success of the aforementioned approaches has been great; however further advances using such approaches have been hampered by a lack of underlining scientific understanding of the catalyst activity, particle growth mechanisms, and optimization strategies for designing composite electrodes The objectives of this report are: (1) Development of durable, high mass activity Platinum Group Metal (PGM) cathode catalysts-enabling lower cost fuel cells; (2) Elucidation of the fundamental relationships between PGM catalyst shape, particle size and activity to help design better catalysts; (3) Optimization of the cathode electrode layer to maximize the performance of PGM catalysts-improving fuel cell performance and lowering cost; (4) Understanding the performance degradation mechanisms of high mass activity cathode catalysts-provide insights to better catalyst design; and (5) Development and testing of fuel cells using ultra-low loading high activity PGM catalysts-validation of advanced concepts.

08 HYDROGEN↗

Synthetic Sling Failure - Evaluations and Recommendations

The information and evaluations provided in this report were compiled to address the recurring problem of synthetic sling failure. As safety is the number one priority in all work aspects, a solution must be devised to prevent accidents from occurring. A total of thirteen cases regarding synthetic sling failure were evaluated in order to determine their causes, effects, and preventative measures. From the collected data, it was found that all cases in which the synthetic sling contacted the edge of its load resulted in sling failure. It is required that adequate synthetic sling protection devices be used to protect slings in any lift where the sling comes in direct contact with the edge or corner of its load. However, there are no consensus codes or standards stating the type, material, or purpose of the type of protective device used to protect the sling from being cut. Numerous industry standards and codes provide vague descriptions on how to protect synthetic slings. Without a clear, concise statement of how to protect synthetic slings, it is common for inadequate materials and sling protection devices to be used in an attempt to meet the intent of these requirements. The use of an inadequate sling protection device is the main cause of synthetic sling failure in all researched cases. Commercial sling protection devices come in many shapes and sizes, and have a variety of names, as well as advertised uses. 'Abrasion pads' and 'wear protectors' are two different names for products with the same intended purpose. There is no distinguishable way to determine the extent of sling protection which these devices will provide, or what specific scenarios they are made for. This creates room for error in a field where error is unacceptable. This report provides a recommended action for hoisting and rigging activities which require synthetic slings to contact a load, as well as recommended changes to industry standards which will benefit overall industry safety.

42 ENGINEERING↗

Shape Measurement of Large Aerospace Structures Using Sensitivity Electrical TDR Distributed Strain Sensor

Electrical time domain reflectometry (ETDR) sensing technique can be best described as "closed-loop radar," where the information is derived from the reflections of a voltage pulse sent through a transmission medium. The ETDR sensing technique is a well-developed method and has been widely used to locate and evaluate discontinuities in long coaxial power transmission cables. The ETDR technique provides a true distributed sensing capability which can not only sense the distributed loading condition of the structure but also can pin-point the location of disturbance, such as the locations of stress concentration and structural damages. Proof-of-concept experiments have been conducted using photoelastic specimens with embedded commercial coaxial cables, i.e., RG85/U and RG174, to demonstrate the stress/strain sensing capability of ETDR sensors for structural health monitoring application. Although the test results showed that the ETDR sensor signals capture specimen deformation pattern both in bending and tension and indicate the location and type of crack damages of the photoelastic specimen; yet, the low signal-to-noise ratio of the sensor signal smears the details of the strain measurement that the ETDR signals can convey. A high-sensitivity ETDR coaxial strain sensor prototype newly developed at Clark Atlanta University will be presented. The construction of the prototype sensing cable as well as its electrical properties relevant to distributed strain sensing application will be shown in details. Test results of the sensitivity and tension responses of the ETDR signal of the prototype sensor will be presented and compared with those of commercial coaxial cables. Promising potentials of the ETDR distributed strain sensing method for shape measurement application of large aerospace structures will also be demonstrated using long slender beam with surface-bonded ETDR distributed strain sensor.

Lin, Mark W.↗

Tailored ramp-loading via shock release of stepped-density reservoirs

The concept of a gradient piston drive has been extended from that of a single component reservoir, such as a high explosive, to that of a multi-component reservoir that utilizes low density foams and large shocks to achieve high pressures ({approx}3.5 mbar) and controlled pressure vs. time profiles on a driven sample. Simulated and experimental drives shaped through the use of multiple component (including carbonized resorcinol formaldehyde and SiO{sub 2} foam) reservoirs are compared. Individual density layers in a multiple component reservoir are shown to correlate with velocity features in the measured drive which enables the ability to tune a pressure drive by adjusting the components of the reservoir. Pre-shot simulations are shown to be in rough agreement with the data, but post-shot simulations involving the use of simulated plasma drives were needed to achieve an exact match. Results from a multiple component reservoir shot ({approx}3.5 mbar) at the National Ignition Facility are shown.

36 MATERIALS SCIENCE↗

Detailed Characterization of Particulates Emitted by Pre-Commercial Single-Cylinder Gasoline Compression Ignition Engine

Gasoline Compression Ignition (GCI) engines have the potential to achieve high fuel efficiency and to significantly reduce both NOx and particulate matter (PM) emissions by operating under dilute partially-premixed conditions. This low temperature combustion strategy is dependent upon direct-injection of gasoline during the compression stroke and potentially near top dead center (TDC). The timing and duration of the in-cylinder injections can be tailored based on speed and load to create optimized conditions that result in a stable combustion. We present the results of advanced aerosol analysis methods that have been used for detailed real-time characterization of PM emitted from a single-cylinder GCI engine operated at different speed, load, timing, and number and duration of near-TDC fuel injections. PM characterization included 28 measurements of size and composition of individual particles sampled directly from the exhaust and after mass and/or mobility classification. We use these data to calculate particle effective density, fractal dimension, dynamic shape factors in free-molecular and transition flow regimes, average diameter of primary spherules, number of spherules, and void fraction of soot agglomerates.

Environmental Molecular Sciences Laboratory↗

TOPO-capped silver selenide nanoparticles and their incorporation into polymer nanofibers using electrospinning technique

Highlights: • Ag{sub 2}Se nanoparticles produced spherical particles with sizes 12 nm (180 °C) and 27 nm (200 °C). • Higher temperature produced increased particle size (∼75 nm) and changed in shape. • Ag{sub 2}Se nanoparticles (0.2–0.6%) added into PVP (35–45%) to yield reduced fiber beading. • Polymer nanofibers electrospun at 11–20 kV produced fiber diameters of 425–461 nm. • Optical properties in the fibers were observed due to the Ag{sub 2}Se nanoparticles loaded. - Abstract: Electrospinning is the most common technique for fabricating polymer fibers as well as nanoparticles embedded polymer fibers. Silver selenide nanoparticles were synthesized using tri-n-octylphosphine (TOP) as solvent and tri-n-octylphosphine oxide (TOPO) as capping environment. Silver selenide was prepared by reacting silver nitrate and selenium with tri-n-octylphosphine (TOP) to form TOP–Ag and TOP–Se solutions. Both absorption and emission spectra signify the formation of nanoparticles as well as the TEM which revealed spherical particles with an average particle size of 22 nm. The polymer, PVP used was prepared at concentrations ranging from (35 to 45 wt%) and the TOPO-capped silver selenide nanoparticles (0.2 and 0.6 wt%) were incorporated into them and electrospun by varying the voltage from 11 to 20 kV. The SEM images of the Ag{sub 2}Se/PVP composite fibers revealed the fibers of diameters with average values of 425 and 461 nm. The X-ray diffraction results show peaks which were identified due to α-Ag{sub 2}Se body centered cubic compound. The sharp peak observed for all the samples at 2θ = 44.5 suggest the presence of Ag in the face centered cubic which can be attributed to higher concentration of silver nitrate used with molar ratio of selenium to silver and the abundance of silver in the silver selenide crystal. Fourier transform infrared spectroscopy, thermogravimetric analysis (TGA) and ultraviolet–visible spectroscopy were used to characterize the structure of the PVP/Ag{sub 2}Se composite fibers.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Structure of mycobacterial 3'-to-5' RNA:DNA helicase Lhr bound to a ssDNA tracking strand highlights distinctive features of a novel family of bacterial helicases

Mycobacterial Lhr is a DNA damage-inducible superfamily 2 helicase that uses adenosine triphosphate (ATP) hydrolysis to drive unidirectional 3'-to-5' translocation along single-stranded DNA (ssDNA) and to unwind RNA:DNA duplexes en route. ATPase, translocase and helicase activities are encompassed within the N-terminal 856-amino acid segment. The crystal structure of Lhr-(1–856) in complex with AMPPNP•Mg 2+ and ssDNA defines a new helicase family. The enzyme comprises two N-terminal RecA-like modules, a winged helix (WH) domain and a unique C-terminal domain. The 3' ssDNA end binds in a crescent-shaped groove at the interface between the first RecA domain and the WH domain and tracks 5' into a groove between the second RecA and C domains. A kissing interaction between the second RecA and C domains forms an aperture that demarcates a putative junction between the loading strand tail and the duplex, with the first duplex nucleoside bookended by stacking on Trp597. Intercalation of Ile528 between nucleosides of the loading strand creates another bookend. Coupling of ATP hydrolysis to RNA:DNA unwinding is dependent on Trp597 and Ile528, and on Thr145 and Arg279 that contact phosphates of the loading strand. The structural and functional data suggest a ratchet mechanism of translocation and unwinding coupled to ATP-driven domain movements.

59 BASIC BIOLOGICAL SCIENCES↗

Design, fabrication and delivery of an improved single Elastic Loop Mobility System (ELMS)

Several significant design improvements have been incorporated into the second-generation full-scale ELMS unit. A major improved design accomplishment was the increase of the load carrying capacity of elastic loops without severe weight or stress penalties. Redesign of the loop form and size, plus selection of a more advanced titanium alloy, resulted in performance characteristics representing a marked improvement over the first-generation unit. Another important design improvement was the shaping of the loop's footprint into a favorable form for uniform pressure distribution. Other improvements are associated with a more efficient drive torque transmission from the internal drive drums to the elastic loop which are expected to reduce the internal losses of the drive system. The new ELMS unit will be capable of being integrated, on a modularized basis, with a multi-loop articulated ELMS test vehicle as the next logical step in the development of the mobility concept.

Trautwein, W.↗

Response of a seat-passenger system to impulsive loading.

This paper presents a summary of a study of the dynamic response of an aircraft seat-passenger system to impulsive loading typical of aircraft crash situations. A brief description of the computer model SIMULA is presented, and selected data from 305 separate cases which have been studied are discussed. Maximum system forces, displacements, velocities, and accelerations are presented as functions of velocity change, aircraft deceleration, crash pulse shape, passenger weight, and seat belt slack. Data from both single and coupled parameter studies are included. A correlation of SIMULA results with experimentally obtained data is made.

Collins, J. A.↗

The Total In-Flight Simulator (TIFS) aerodynamics and systems: Description and analysis

The aerodynamics, control system, instrumentation complement and recording system of the USAF Total In/Flight Simulator (TIFS) airplane are described. A control system that would allow the ailerons to be operated collectively, as well as, differentially to entrance the ability of the vehicle to perform the dual function of maneuver load control and gust alleviation is emphasized. Mathematical prediction of the rigid body and the flexible equations of longitudinal motion using the level 2.01 FLEXSTAB program are included along with a definition of the vehicle geometry, the mass and stiffness distribution, the calculated mode frequencies and mode shapes, and the resulting aerodynamic equations of motion of the flexible vehicle. A complete description of the control and instrumentation system of the aircraft is presented, including analysis, ground test and flight data comparisons of the performance and bandwidth of the aerodynamic surface servos. Proposed modification for improved performance of the servos are also presented.

Andrisani, D., II↗

Cradles for Support in Transit

C-shaped cradles distribute weight of large objects. Originally developed for holding satellite in bay of Space Shuttle orbiter, concept also adaptable to such terrestrial uses as carrying odd-shaped equipment by truck. Cradle set consists of single prime cradle and several basic cradles. Composed of bar bent into a half circle, each cradle has own keel and longeron trunnions that brace structure by mating with receptacles in vehicle and its own foam pads, on which load rests. One 548-lb (249-kg) cradle supports up to 3,000 lb (1,361 kg); thus, 15,000-lb (6,800-kg) object requires five cradles distributed along its length. Through their trunnions, cradles spread weight of load along vehicle.

Crane, W. H.↗

Time-domain transient elastodynamic analysis of 3-D solids by BEM

The BEM algorithm developed by Banerjee and Ahmad (1985) and Banerjee et al. (1986) for the analysis of three-dimensional time-dependent elastodynamics problems is extended and refined to improve the accuracy of the internal stress predictions. A quadratic spatial shape function and a linear temporal shape function are employed, and the complete numerical implementation (as part of BEST3D) is outlined. Applications of the improved BEM to typical problems are presented graphically and briefly characterized. Included are spherical cavities subjected to sudden radial expansion, triangular or rectangular pulses of radial pressure, or ramp loading; a circular loaded area on a half space; and a flexible square plate foundation on an elastic half space.

Ahmad, S.↗