Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “lightweight”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92

Microstructure and Strain Rate-Dependent Tensile Deformation Behavior of Fiber Laser-Welded Butt Joints of Dual-Phase Steels

The microstructure and tensile deformation behavior of the fiber laser-welded similar and dissimilar dual-phase (DP) steel joints over a wide range of strain rates from 10{sup −3} to 10{sup 3} s{sup −1} were investigated for the further applications on the lightweight design of vehicles. The high strain rate dynamic tensile deformation process and full-field strain distribution of the base metals and welded joints were examined using the digital image correlation method and high-speed photography. The strain rate effects on the stress–strain responses, tensile properties, deformation, and fracture behavior of the investigated materials were analyzed. The yield stress (YS) and ultimate tensile strength (UTS) of the dissimilar DP780/DP980 welded joints were lying in-between those of the DP780 and DP980 base metals, and all materials exhibited positive strain rate dependence on the YS and UTS. Owing to the microstructure heterogeneity, the welded joints showed relatively lower ductility in terms of total elongation (TE) than those of the corresponding base metals. The strain localization started before the maximum load was reached, and the strain localization occurred earlier during the whole deformation process with increasing strain rate. As for the dissimilar welded joint, the strain localization tended to occur in the vicinity of the lowest hardness value across the welded joint, which was in the subcritical HAZ at the DP780 side. As the strain rate increased, the typical ductile failure characteristic of the investigated materials did not change.

36 MATERIALS SCIENCE↗

Investigation of Mechanical and Electromagnetic Interference Shielding Properties of Nickel–CFRP Textile Composites

The most common materials used for electromagnetic interference shielding are metals and their alloys. However, those materials are heavy and highly reflective. In order to eliminate or reduce the intensity of wave radiation in their working environment, lightweight materials that have interference shielding properties are needed. In this paper, nickel wire mesh yarns (warps) were woven into carbon fibers-reinforced plastic yarns (wefts) to produce metal–carbon textile composite materials. The plain weave and 2/2 twill weave techniques were used, and the woven fabrics were laminated to manufacture experimental test samples. The nickel, which has high magnetic permeability and good electric conductivity, and carbon fibers, which have good electrical, thermal and mechanical properties, were used together to achieve the desired properties. The shielding effectiveness of each sample was investigated using a network analyzer connected with coaxial transmission line test in accordance with ASTM 4935-99 standard, with the frequencies ranging from 500 MHz to 1.5 GHz. Here, the plain weave structure showed higher shielding effectiveness than twill weave. The absorption losses for both materials were relatively greater than reflection losses. In reference to the orientation of wire mesh yarns about the loading axis, the tensile strengths in the transversal direction were 19.04 and 16.34% higher than the tensile strengths in longitudinal direction for plain weave and twill weave, respectively. The fractography analysis with SEM showed a ductile fracture of wire mesh and brittle fracture of epoxy matrix and carbon fibers.

36 MATERIALS SCIENCE↗

Influence of Welding Strength Matching Coefficient and Cold Stretching on Welding Residual Stress in Austenitic Stainless Steel

Austenitic stainless steel is widely used in pressure vessels for the storage and transportation of liquid gases such as liquid nitrogen, liquid oxygen, and liquid hydrogen. Cryogenic pressure vessel manufacturing uses cold stretching technology, which relies heavily on welding joint performance, to construct lightweight and thin-walled vessels. Residual stress from welding is a primary factor in cases of austenitic stainless steel pressure vessel failure. In this paper, on the basis of Visual Environment 10.0 finite element simulation technology, the residual stress resulting from different welding strength matching coefficients (0.8, 1, 1.2, 1.4) for two S30408 plates welded with three-pass butt welds is calculated according to thermal elastoplastic theory. In addition, the stress field was calculated under a loading as high as 410 MPa and after the load was released. Path 1 was set to analyze stress along the welding line, and path 2 was set to analyze stress normal to the welding line. The welding strength matching coefficient strongly affected both the longitudinal residual stress (center of path 1) and the transverse residual stress (both ends of path 1) after the welding was completed. However, the coefficient had little effect on the longitudinal and transverse residual stress of path 2. Under the loading of 410 MPa, the longitudinal and transverse stress decreased and the stress distribution, with different welding strength matching coefficients, was less diverse. After the load was released, longitudinal and transverse stress distribution for both path 1 and path 2 decreased to a low level. Cold stretching could reduce the effect of residual stress to various degrees. Transverse strain along the stretching direction was also taken into consideration. The experimental results validated the reliability of the partial simulation.

36 MATERIALS SCIENCE↗

Microstructure Evolution and Mechanical Properties of Keyhole Repair Welds in AA 2219-T851 Using Refill Friction Stir Spot Welding

The search for a suitable friction-based keyhole repair technique that fulfills the requirements for high-quality repair welds has become an important research topic, especially for aerospace applications. In order to provide and analyze an universal keyhole repair method for lightweight metals, refill friction stir spot welding is applied to through-hole repairs in 3- and 6-mm-thick sheets of precipitate hardening AA 2219-T851. Keyholes with a diameter of 7.5 mm were repair welded achieving a defect-free microstructure. The correlation between the microstructural evolution imposed by the repair process and the resulting mechanical properties is shown. A comprehensive analysis of the precipitate evolution in peak-aged AA 2219 during RFSSW is presented. Thermal cycle measurements revealed high heating rates and peak temperatures of up to 520 °C in the weld center. The thermal cycle caused mainly dissolution and minor equilibrium phase formation in the stirred zone. In the HAZ, overaging of the strengthening precipitates dominates with minor dissolution and equilibrium phase formation only in the direct proximity of the SZ. Microstructural analysis revealed typical weld zone formation with inhomogeneous grain size distribution in the SZ. The resulting mechanical properties are dominated by an inhomogeneous hardness distribution with lowest hardness in the TMAZ at 5 mm from the center of the weld. During tensile loading main yielding and the final fracture occur in the area of lowest strength. Tensile testing showed yield strength of 40 to 46% and UTS of 28 to 25% below BM values in 3- and 6-mm-thick sheets, respectively. The sheet thickness and post-weld natural aging were found to influence the mechanical properties of the weld significantly.

36 MATERIALS SCIENCE↗

Effect of Orientation of Weld Line on Formability of Electron Beam-Welded Dissimilar Thickness Titanium Sheets

Recently, manufacturing industries are looking forward to get insight into the influence of weld orientation on formability of tailor-welded blanks (TWBs) of titanium sheets for design and fabrication of lightweight components. Hence, commercially pure titanium (CP Ti) sheets of 1.0 and 1.2 mm thickness were joined together by electron beam welding process using accelerating voltage of 55 kV, beam current of 14.9 mA and welding speed of 865 mm/min. Two different types of TWBs with weld line perpendicular to the rolling direction (WL ⊥ RD) and weld line parallel to the rolling direction (WL || RD) were fabricated, and subsequently, the tensile test, microstructure and microhardness characterizations were conducted to ensure quality of weld. The limiting dome height (LDH) tests were carried out using laboratory-scale setup to evaluate forming behavior of both the above TWBs in terms of FLD, strain distribution, weld line movement and failure location. It was found that the tensile stress–strain response and formability performance of TWBs were significantly influenced by weld line orientation with lower ductility, ultimate tensile strength and LDH in TWB of WL || RD. Moreover, significant weld line movement and non-uniform strain distribution with necking and subsequently fracture were observed away from the weld line in thinner 1.0 mm CP Ti sheets depending on both sample geometry and weld line orientation.

36 MATERIALS SCIENCE↗

The Hot Bending and Diffusion Bonding of TiAl-Based Alloy for Corrugated-Core Sandwich Structure

The multi-layer structure of TiAl-based alloys can meet the demand of having lightweight and high-strength properties at elevated temperature. In this paper, the corrugated-core sandwich structure of a TiAl-based alloy was fabricated by the hot bending/diffusion bonding process. In order to fabricate this structure, the high-temperature tensile property, hot bending behavior, and vacuum diffusion bonding of a Ti-47.5Al-Cr-V alloy were investigated. The flow behavior was evaluated by uniaxial tensile experiment, and the results showed that the alloy exhibited good plasticity at the given conditions, and the maximum elongation reached 200% at 1000 °C at strain rate of 3 × 10{sup −4} s{sup −1}. The bending experiments were also performed at temperatures of 950, 1000, and 1050 °C with fillet radii of R = 0, 0.5, and 1 mm, respectively. No micro-/macro-defects developed. The vacuum diffusion bonding of this alloy was also carried out, and the shear bonding strength of bonding joints was measured at room temperature. The maximum shear strength was 398 MPa, and the joint was obtained at 1000 °C/30 MPa/3 h. Combining the bonding interface with the shear strength of different joints, the appropriate bonding pressure and bonding time for diffusion bonding of the TiAl alloy at 1000 °C were 20 MPa and 2 h, respectively. Then, the forming process of the corrugated-core sheet was conducted at 1000 °C with a fillet radius of 1 mm. Finally, the corrugated-core sandwich structure was manufactured under vacuum atmosphere, and the mechanical properties and the interface microstructure were investigated.

36 MATERIALS SCIENCE↗

Mechanical Properties and Corrosion Behavior of AA5754-AA6061 Dissimilar Aluminum Alloys Welded by Cold Metal Transfer

The trend of using lightweight materials in the automotive industry brings along the necessity of dissimilar welding of aluminum alloys such as AA5754 and AA6061. Hybrid structures in automobiles are subjected not only to mechanical forces but also corrosive effects of the environment. In this study, cold metal transfer welding, which is suitable for welding thin sheets and dissimilar materials, was applied to join AA5754 to AA6061. It was aimed to investigate the effect of weld heat input on mechanical properties and corrosion rate measured by the Tafel extrapolation method in 3.5 wt.% NaCl solution at room temperature. The tensile strength of AA5754-AA6061 joints tended to reduce with increasing heat input. Corrosion test results showed that the increased heat input decreased the corrosion resistance and caused intergranular corrosion besides pitting corrosion.

36 MATERIALS SCIENCE↗

Effect of Rotational Speed on Microstructure and Mechanical Properties in Submerged Friction Stir Welding of ME20M Magnesium Alloy

Submerged friction stir welding of magnesium alloys has not been well investigated to date. ME20M is an important lightweight magnesium (Mg) alloy with enhanced yield strength and heat resistance that merits further research. In this paper, submerged friction stir welding of the ME20M Mg alloy was carried out using different parameters for the underwater cooling. Defect-free weld joints were produced, and the macrostructure, microstructure, tensile properties, and hardness were investigated. The results show that by increasing the rotational speed, the grain size of the weld nugget increased, the tensile strength of the joint decreased, and the microhardness of the different weld zones decreased. The finest obtained grain size was about 3.5 µm in the weld nugget at a rotational speed of 1100 rpm. The highest tensile strength achieved was 183.2 MPa, which was ~ 76.32% of the base metal. The highest and lowest hardness values of the weld joint were obtained at rotational speeds of 1100 and 1600 rpm, respectively, in the weld nugget and heat-affected zones.

36 MATERIALS SCIENCE↗

Development of Constitutive Relationship for Thermomechanical Processing of Al-SiC Composite Eliminating Deformation Heating

Constitutive equations are useful for computational or numerical tools in describing the thermomechanical behavior of Al/SiC composites to develop the lightweight component using bulk metal forming. In this study, the uniaxial compression test of powder metallurgy-based Al/7 vol.% SiCp composite samples in the temperature range of 250-500 °C and at the strain rates of 0.001, 0.007, 0.05, 0.3, 2.2 and 15 s{sup −1} was performed on a Gleeble-3800 thermomechanical simulator. An equation correlating actual (measured) temperature with the true stress in real time has been established for each of the strain rates. Further, the true stress was corrected by eliminating the effect of deformation heating using this equation based on the experimental observations. The temperature-corrected true stress data were then used for development of constitutive equations using the Arrhenius model, strain-compensated Arrhenius model and modified Johnson–Cook (m-JC) model. The material parameters in the m-JC model were calculated at different combinations of temperatures and strain rates. The established constitutive equations are validated with temperature-corrected true stress from the experiment. Further, these equations are verified with the experimental true stress that was obtained using different inputs of temperatures and strain rates in a compression test. The correlation coefficient (R) and absolute average relative error reflect the accuracy of constitutive models. The result indicates that the calculated true stress by the established strain-compensated Arrhenius model is in good agreement with that of experimentally measured true stress with a correlation coefficient of 0.996 and relative error of 3.83%.

36 MATERIALS SCIENCE↗

Development of Pore-Free Ti-Si-C MAX/Al-Si Composite Materials Manufactured by Squeeze Casting Infiltration

Open-porous MAX phase skeletons from Ti{sub 3}SiC{sub 2} were manufactured by Microwave-Assisted Self-propagating High-temperature Synthesis (MASHS) and subsequently subjected to squeeze casting infiltration with an Al-Si lightweight casting alloy (EN AC-44200). This alloy was chosen due to its high flowability, corrosion resistance and good machinability. The manufactured composites, together with a reference sample of the original alloy, underwent testing of thermal properties, including thermal conductivity and diffusivity, specific heat and thermal expansion in the temperature range 50-500 °C, which corresponds to the expected working temperatures of the material. The fabricated AlSi/Ti{sub 3}SiC{sub 2} composites have significantly increased thermal stability, with coefficients of thermal expansion (approximately 10-11 × 10{sup −6} °C{sup −1}) half that of the original alloy. As regards mechanical properties, the instrumental Young’s modulus and Vickers hardness of the composite materials are 170.8 and 8.5 GPa, respectively. Moreover, the microstructure and phase composition, structural defects and potential impacts between constituents of the manufactured composites were characterized using SEM, TEM and STEM microscopy and EDS and XRD analysis.

36 MATERIALS SCIENCE↗

The TMS Magnesium Committee: Committed to the Advancement of Global Magnesium Technology

The TMS Magnesium Committee was established in the year 2000 as a spin-off of the Reactive Metals Committee, triggered by the strong global growth of magnesium being used in a variety of structural lightweight applications since the mid-1990’s. Since then the committee has seen a distinct development in terms of size, participation and focus. The article at hand outlines this development by recapitulating the output of its two main activities: the annual Magnesium Technology Symposia and the JOM Special Issues dedicated to magnesium research and development. Further records on the Magnesium Committee are available from the committee homepage (accessible through http://members.tms.org).

36 MATERIALS SCIENCE↗

Surface characterization of carbon fiber polymer composites and aluminum alloys after laser interference structuring

Here, the increasing use of Carbon Fiber-reinforced Polymer matrix Composites (CFPC) and aluminum alloys as lightweight materials in the automotive and aerospace industries demands enhanced surface preparation and control of surface morphology prior to joining. In this study, surfaces of both composite and aluminum were prepared for joining using an Nd:YAG laser in a two-beam interference setup, enabling the (a) structuring of the AL 5182 surface, (b) removal of the resin layer on top of carbon fibers, and (c) structuring of the carbon fibers. CFPC specimens of T700S carbon fiber, Prepreg - T8 3 epoxy, 5 ply thick, 0/90o plaques were used. The effect of laser fluence, scanning speed, and number of shots-per-spot was investigated on the removal rate of the resin without an excessive damage of the fibers. Optical micrographs, 3D imaging, and scanning electron microscope (SEM) imaging were used to study the effect of the laser processing on surface morphology.

36 MATERIALS SCIENCE↗

Molecular Statics Analyses of Thermodynamics and Kinetics of Hydrogen Cottrell Atmosphere Formation Around Edge Dislocations in Aluminum

Aluminum alloys are being explored as lightweight structural materials for use in hydrogen-containing environments. In this paper, to understand hydrogen effects on deformation, we perform molecular statics studies of the hydrogen Cottrell atmosphere around edge dislocations in aluminum. First, we calculate the hydrogen binding energies at all interstitial sites in a periodic aluminum crystal containing an edge dislocation dipole. This allows us to use the Boltzmann equation to quantify the hydrogen Cottrell atmosphere. Based on these binding energies, we then construct a continuum model to study the kinetics of the hydrogen Cottrell atmosphere formation. Finally, we compare our results with existing theories and discuss the effects of hydrogen on deformation of aluminum-based alloys.

36 MATERIALS SCIENCE↗

Crafting Multifunctional Materials with Tailored Mechanical and Magnetic Properties by Solid-State Non-equilibrium Processing

Aluminum matrix composites hold promise for creating lightweight structural components with multifunctional properties. Nonetheless, achieving desired magnetic or electrical characteristics without compromising their fundamental mechanical properties presents a significant challenge. Here, in this study, we explore mechanical stir-based extrusion as a solid-state metalworking technique to develop fine-grained microstructures and highly refined metallic composites. Our study focuses on creating a SmCo 5 -reinforced aluminum matrix composite using solid stir extrusion (SSE) and assessing its microstructure, mechanical, and magnetic properties through a comprehensive suite of characterization tools, including x-ray diffraction, electron microscopy, and magnetometry. Our findings reveal that incorporating a small amount (3.76 wt.%) of SmCo 5 phase in a non-heat-treatable, non-magnetic aluminum alloy via SSE yields a composite that exhibits good hard magnetic characteristics with a large coercivity (H ci = 13.5 kOe) and improved mechanical properties. This study underscores non-equilibrium processing via solid-state high-speed stirring as a compelling method for crafting multifunctional materials with tailored mechanical and magnetic properties.

36 MATERIALS SCIENCE↗

Comparative Study of Zinc Cold-Spray Coating and Pre-treatments for Magnesium Alloys

Magnesium (Mg) alloys are appealing for automotive lightweighting owing to their high specific strength. However, their susceptibility to corrosion in harsh environments remains a major challenge. Conventional industrial pre-treatment coatings, including zinc phosphate, chromate conversion, and non-chromate conversion, often exhibit discontinuities and microcracks, leading to localized corrosion near fasteners and parting lines. Here, this study investigates cold-sprayed zinc (Zn) coatings as a novel pre-treatment alternative for high-pressure die cast (HPDC) AZ91 Mg alloys, demonstrating significant improvements in wear and corrosion performance. Cold spray produces uniform and robust coatings, reducing wear rate by over 50% and reducing corrosion rate by over 99.3%, as measured by evolved hydrogen release, compared to traditional pre-treatments. Multimodal corrosion testing reveals that Zn cold-spray coatings form a protective layer during exposure, minimizing general and filiform corrosion, and exhibiting corrosion potential (E corr ) that is nobler by ~ 400 mV than the surfaces of both pre-treated and uncoated AZ91. Scalability of cold spray for selective application around multimaterial joints further strengthens their industrial viability. This work establishes Zn cold-spray coatings as highly effective pre-treatment solutions for the advancement of corrosion resistant Mg alloy components in automotive applications.

multimodal corrosion↗

Predicting Sintering Window of Binder Jet Additively Manufactured Parts Using a Coupled Data Analytics and CALPHAD Approach

Batch-to-batch variation in powder compositions for binder jet additive manufacturing (BJAM) can significantly deter defining an “ideal” sintering window for a given alloy. One way to overcome the problem is by running sintering experiments at various temperatures for each batch of the powder. However, such an approach increases the time required to achieve large-scale production of parts. The predictive capabilities of computational thermodynamic tools like CALPHAD can be leveraged to overcome the challenge, especially for binder jet additive manufacturing, since the process occurs under near-equilibrium conditions. However, calculating the sintering window using CALPHAD can be computationally expensive, considering many possible feedstock compositions within “specification”. Here, we generate high throughput CALPHAD data for nickel-based superalloys to develop machine learning models to predict the sintering window rapidly. The predictive capability of the models has been validated using published results on BJAM of Inconel 718 and 625. Further, validated models are lightweight and can be deployed in an industrial setting to get sintering window in an accelerated manner.

36 MATERIALS SCIENCE↗

Achieving Metallurgical Bonding in Aluminum/Steel Bimetallic Castings

Abstract Aluminum castings are increasingly being used in automotive powertrain and structural applications for vehicle lightweighting. Cast aluminum parts often need to be machined and joined to steel components in multi-material systems. Bimetallic components produced by casting aluminum over steel substrate are advantageous due to the elimination of machining and traditional dissimilar material joining processes. However, forming a strong metallurgical bonding during overcasting process has been challenging. In this paper, the effects of processing conditions such as substrate surface preparation, pre-heating temperature, melt conditions as well as casting design were studied by investigating the bimetallic interfaces for aluminum A319 casting alloy and a high alloy steel substrate in a sand-casting process. Zn and Al-based substrate coatings were evaluated. The experimental results suggest a metallurgical bond between aluminum and steel can be formed during the sand-casting process via high temperature diffusion with or without coatings. Al-based substrate coating prior to overcasting results in the formation of a continuous layer of intermetallics at the bimetallic interface, with large Al–Si–Fe intermetallics penetrating the cast aluminum.

Moodispaw, Michael P. (ORCID:0000000267635882)↗

Relative Hausdorff distance for network analysis

Similarity measures are used extensively in machine learning and data science algorithms. The newly proposed graph Relative Hausdorff (RH) distance is a lightweight yet nuanced similarity measure for quantifying the closeness of two graphs. In this work we study the effectiveness of RH distance as a tool for detecting anomalies in time-evolving graph sequences. We apply RH to cyber data with given red team events, as well to synthetically generated sequences of graphs with planted attacks. In our experiments, the performance of RH distance is at times comparable, and sometimes superior, to graph edit distance in detecting anomalous phenomena. Furthermore, our results suggest that in appropriate contexts, RH distance has advantages over more computationally intensive similarity measures.

97 MATHEMATICS AND COMPUTING↗