SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The structure of the ionic liquid choline lysinate ([Ch][Lys]) and its water mixtures, including a dissolved model lignin residue, guaiacol, is revealed at atomic and nanoscale resolution using neutron diffraction.
Prior work with electrosprays in vacuum of mixtures of ionic liquids (ILs) and the moderately high boiling point (T{sub b}) solvents formamide (FM) and propylene carbonate (PC) (T{sub b} of 210 and 241 °C) has shown that the charged drops produced have reasonably narrow charge/mass distributions, controllable over a wide mass/charge range. This enables their use as propellants in electrical propulsion with specific impulse I{sub sp} varying from a few hundred to a few thousand seconds (10 kV beam energy) and with excellent propulsion efficiency. However, some limitations are imposed by the finite room temperature volatility of FM and PC. Here, we seek improved performance from propellants based on the polar but viscous solvent Sulfolane (SF; ε = 43.2, μ = 10.3 cP) and the low viscosity but less polar solvent tributyl phosphate (TBP; ε = 8.9, μ = 3.4 cP), both with T{sub b} > 280 °C. Neither TBP nor its low viscosity mixtures with SF achieve the electrical conductivities needed to yield high I{sub sp}. Most ILs used in SF/IL mixtures tested were based on the 1-ethyl-3-methylimidazolium (EMI) or 1,3-dimethylimidazolium (DMI) cations, including EMI-BF{sub 4}, EMI-N(CN){sub 2}, and DMI-N(CN){sub 2}. These combinations reach high conductivities, some approaching 3 S/m, but have limited propulsive performance because evaporation of ions directly from the electrified meniscus produces undesirable mixed beams of drops and ions. Exceptional characteristics are found in mixtures of SF with ethylammonium nitrate (EAN), where the small EA{sup +} cation is strongly bound to the solvent, greatly delaying ion evaporation from the meniscus. Evidence on the formation of nano-jets with diameters as small as 1 nm is seen. Although unprecedented, this finding agrees with what would be expected if ion evaporation were suppressed. SF/EAN mixtures thus provide the best available sources to produce the smallest possible nanodrops, minimally polluted by ions.
This report presents a comprehensive model for advanced membrane-based absorber components accounting for three separate fluid streams, one of them providing internal cooling, with complex flow patterns. The model was implemented with various liquid desiccants and their properties (including LiCl, CaCl 2 , and [emim][OMS] ionic liquid [IL]). The model has been validated using data from two laboratory prototype absorbers, one with CaCl 2 as the working fluid and one with an IL as the working fluid. Entropy analysis was further carried out to verify the model and understand effect of internal cooling on the entropy variation of three fluid streams. The developed model and codes are expected to enable detailed configuration optimization and provide in-depth understanding of three-fluid heat and mass exchanger (HMX) performance. The paper also describes parametric studies of the HMX components in utilizing the latent heat removed in space cooling to heat water and numerically explores the unique benefit of its application in a semi-open absorption heat pump water heater. The results show that a single three-fluid HMX has the potential to achieve simultaneous dehumidification and water heating efficiently at cost effectiveness, particularly in hot and humid climates.
Pore size is a crucial factor impacting gas separation in porous separation materials, but how to control the pore size to optimize the separation performance remains a challenge. Here, we propose a design of graphene/ionic liquid composites with tunable slit pore sizes, where cations and anions of ionic liquids are intercalated between graphene layers. By varying the sizes of the ions, we show from first-principles density functional theory calculations that the accessible pore size can be tuned from 3.4 to 6.0 Å. Grand canonical Monte Carlo simulations of gas sorption find that the composite materials possess high CO 2 uptake at room temperature and 1 bar (up to ~8.5 mmol/g). Further simulations of the sorption of gas mixtures reveal that high CO 2 /N 2 and CO 2 /CH 4 adsorption selectivities can be obtained when the accessible pore size is <5 Å. This work suggests a new strategy to achieve tunable pore sizes via the graphene/IL composites for highly selective CO 2 /N 2 and CO 2 /CH 4 adsorption.
Abstract Portable electronic devices are predominantly powered by lithium ion batteries in which the electrolyte is a liquid or gel of lithium salts dissolved in molecular solvents. There have been many attempts to replace the flammable liquid component of the electrolyte by alternative alkali metal transporting media, such as superionic crystals, alkali‐conducting glassy solids, ionic liquids, salt‐in‐molecular plastic crystal solvent, and salt‐in‐ionic plastic crystal solvents. Except for the first two of the above, which have their own problems, all the above have the disadvantage that the alkali cation is the least mobile of the ionic species due to its high charge/radius ratio. Here, some new, silylsulfate‐based are introduced. Members of the class of lithium ion conductor in which the alkali ion is the only cationic species present, and the salt itself is a plastic crystal, a solid in which the anion centers of mass are ordered, but the anion orientations are disordered and dynamic (best example NaCB 9 H 10 , see text). It is shown that depending on the nature of the anion, the conductivity may be within a factor of two of the standard liquid carbonate electrolyte. The soft, spreadable electrolyte, impregnated in Celgard separators, supports truly reversible Li insertion into the LiCoO 2 cathode.
Molecular species with electron affinities (EAs) larger than that of the chlorine atom (3.6131 eV) are superhalogens. The corresponding negative ions, namely, superhalogen anions, are intrinsically very stable with high electron binding energies (EBEs), and widely exist as building blocks of bulk materials and ionic liquids. The most common superhalogen anions proposed and confirmed to date are either ionic salts or compact inorganic species. Herein we report a new class of superhalogen species, a series of tetracoordinated organoboron anions [BL4]– (L = phenyl (1), 4-fluorophenyl (2), 1-imidazolyl (3), L4 = H(pyrazolyl)3 (4)) with bulky organic ligands covalently bound to the central B atom. Negative ion photoelectron spectroscopy (NIPES) reveals all of these anions possessing EBEs higher than that of Cl- with the adiabatic / vertical detachment energy (ADE / VDE) of 4.44/4.8 (1), 4.78/5.2 (2), 5.08/5.4 (3), and 4.59/4.9 eV (4), respectively. First-principles calculations confirmed high EBEs of [BL4]– and predicted that these anions are thermodynamically stable against fragmentation. The unraveled superhalogen nature of these species provides a molecular basis to explain the wide-range applications of tetraphenylborate (TPB) (1) and trispyrazolylborate (Tp) (4) in many areas spanning from industrial waste treatment to soft material synthesis and organometallic chemistry
The present disclosure relates to a composition that includes a fluoropolymer, a polymerized ionic liquid block copolymer (PILBC), and a catalyst, where the fluoropolymer is configured to affect ionic mobility, and the PILBC is configured to affect a property of the catalyst. In some embodiments of the present disclosure, the property may include at least one of oxygen transport and/or an active site functionality of the catalyst.
The partitioning of trace elements between ionic crystals and the melt has been correlated with lattice energy of the host. The solid-liquid partition coefficient has been expressed in terms of the difference in relative ionic radius of the trace element and the homogeneous and heterogeneous strain of the host lattice. Predictions based on this model appear to be in general agreement with data for alkali nitrates and for rare-earth elements in natural garnet phenocrysts.
Paper-based batteries represent a new frontier in battery technology. However, low-flexibility and poor ionic conductivity of solid electrolytes have been major impediments in achieving practical mechanically flexible batteries. This work discuss new highly ionic conductive polymer gel electrolytes for paper-based battery applications. In this paper, we present a poly(vinylidene fluoride-hexafluoropropylene) (PVDH-HFP) porous membrane electrolyte enhanced with lithium bis(trifluoromethane sulphone)imide (LiTFSI) and lithium aluminum titanium phosphate (LATP), with an ionic conductivity of 2.1 × 10{sup −3} S cm{sup −1}. Combining ceramic (LATP) with the gel structure of PVDF-HFP and LiTFSI ionic liquid harnesses benefits of ceramic and gel electrolytes in providing flexible electrolytes with a high ionic conductivity. In a flexibility test experiment, bending the polymer electrolyte at 90° for 20 times resulted in 14% decrease in ionic conductivity. Efforts to further improving the flexibility of the presented electrolyte are ongoing. Using this electrolyte, full-cell batteries with lithium titanium oxide (LTO) and lithium cobalt oxide (LCO) electrodes and (i) standard metallic current collectors and (ii) paper-based current collectors were fabricated and tested. The achieved specific capacities were (i) 123 mAh g{sup −1} for standard metallic current collectors and (ii) 99.5 mAh g{sup −1} for paper-based current collectors. Thus, the presented electrolyte has potential to become a viable candidate in paper-based and flexible battery applications. Fabrication methods, experimental procedures, and test results for the polymer gel electrolyte and batteries are presented and discussed.
A polarity swing-assisted regeneration (PSAR) process is disclosed for improving the efficiency of releasing gases chemically bound to switchable ionic liquids. Regeneration of the SWIL involves addition of a quantity of non-polar organic compound as an anti-solvent to destabilize the SWIL, which aids in release of the chemically bound gas. The PSAR decreases gas loading of a SWIL at a given temperature and increases the rate of gas release compared to heating in the absence of anti-solvent.
Ionogels, pseudo-solid-state electrolytes consisting of an ionic liquid electrolyte confined in a mesoporous inorganic matrix, have attracted interest recently due to their high ionic conductivity and physicochemical stability. These traits, coupled with their inherent solution processability, make them a viable solid electrolyte for solid-state battery systems. Despite the promising properties of ionogels, there have been very few investigations of the electrode–ionogel interface. In the present study, X-ray photoelectron spectroscopy, Raman spectroscopy, and electrochemical measurements were utilized to probe the surface reactions occurring at the electrode–ionogel interface for several electrode materials. Our results indicate that the sol acidity initiates breakdown of the organic constituents of the sol and reduction of the transition metals present in the electrode materials. This chemical attack forms an organic surface layer and affects the electrode composition, both of which can impede Li+ access. By modifying the silica sol–gel reaction via a two-step acid–base catalysis, these interfacial reactions can be avoided. Results are shown for a LiCoO 2 electrode in which a high Li-ion capacity and stable cycling were achieved.
Advancing beyond current lithium-ion technology is necessary in order to enable energy storage devices for electric airplanes. Electrolyte stability is a key limiting factor, yet the design of improved electrolytes remains a formidable challenge. Molecular dynamics (MD) simulations are a powerful tool for studying electrolytes, since they can be used to evaluate structural, thermodynamic, and transport properties, and can provide molecular-level detail often inaccessible to experimental techniques. Our computational materials groups at the NASA Ames Research Center has developed models and methods to accurately simulate both liquid and polymer electrolytes.We report the results from atomistic MD simulations of several electrolyte materials, with lithium salts dissolved in ionic liquids, dimethoxyethane (DME), and polyethylene oxide (PEO). For improved accuracy, we employ polarizable models, where each atom is given an environment-dependent atomic dipole. The simulations accurately predict bulk transport properties, including viscosity, diffusion, and ionic conductivity, in quantitative agreement with available experimental data. Moreover, the simulations provide important insights into the solvation structure of the lithium ions.We also report the results from coarse-grained MD simulations of polyanion electrolytes. In order to more efficiently capture the longer length- and time-scales of these systems, we employ a generic bead-spring model. These simulations provide important insight into how the polymer chain architecture and ionic interaction strengths affect the ionic aggregation behavior and cation dynamics. Despite the simplicity of the model, the simulations yield qualitative agreement with experimental data for similar systems.
Abstract While 3D printing of rechargeable batteries has received immense interest in advancing the next generation of 3D energy storage devices, challenges with the 3D printing of electrolytes still remain. Additional processing steps such as solvent evaporation were required for earlier studies of electrolyte fabrication, which hindered the simultaneous production of electrode and electrolyte in an all‐3D‐printed battery. Here, a novel method is demonstrated to fabricate hybrid solid‐state electrolytes using an elevated‐temperature direct ink writing technique without any additional processing steps. The hybrid solid‐state electrolyte consists of solid poly(vinylidene fluoride‐hexafluoropropylene) matrices and a Li + ‐conducting ionic‐liquid electrolyte. The ink is modified by adding nanosized ceramic fillers to achieve the desired rheological properties. The ionic conductivity of the inks is 0.78 × 10 −3 S cm −1 . Interestingly, a continuous, thin, and dense layer is discovered to form between the porous electrolyte layer and the electrode, which effectively reduces the interfacial resistance of the solid‐state battery. Compared to the traditional methods of solid‐state battery assembly, the directly printed electrolyte helps to achieve higher capacities and a better rate performance. The direct fabrication of electrolyte from printable inks at an elevated temperature will shed new light on the design of all‐3D‐printed batteries for next‐generation electronic devices.
In this paper, atomic force microscopy (AFM) force-distance measurements are used to investigate the layered ion structure of Ionic Liquids (ILs) at the mica surface. The effects of various tip properties on the measured force profiles are examined and reveal that the measured ion position is independent of tip properties, while the tip radius affects the forces required to break through the ion layers as well as the adhesion force. Force data is collected for different ILs and directly compared with interfacial ion density profiles predicted by molecular dynamics. Through this comparison it is concluded that AFM force measurements are sensitive to the position of the ion with the larger volume and mass, suggesting that ion selectivity in force-distance measurements are related to excluded volume effects and not to electrostatic or chemical interactions between ions and AFM tip. Finally, the comparison also revealed that at distances greater than 1 nm the system maintains overall electroneutrality between the AFM tip and sample, while at smaller distances other forces (e.g., van der waals interactions) dominate and electroneutrality is no longer maintained.
The wide spread use of hazardous and expensive solvents for the liquid-liquid extraction (LLE) of critical metals has been a growing source of waste in the metal refinement industry. We have developed and characterized room temperature liquid hydrophobic binary mixtures based on common pharmaceutical and food grade compounds as sustainable, cost effective alternatives to both ionic liquids and conventional solvents. Additionally, we introduce liquid mixtures with Proton Sponge® (1,8-bis(dimethylamino)naphthalene), one of the strongest known organic bases. These mixtures have been applied to the LLE of indium(III) ions from hydrochloric acid solutions, displaying an extraction efficiency greater than 99% in some systems. Here, a systematic approach to identifying the underlying mechanism of extraction, in particular relating to the charge, solubility, and complexation of the indium species in the organic phase has been developed.
Combining broadband impedance spectroscopy, differential scanning calorimetry, and nuclear magnetic resonance we analyzed charge and mass transport in two polymerized ionic liquids and one of their monomeric precursors. In order to establish a general procedure for extracting single-particle diffusivity from their conductivity spectra, we critically assessed several approaches previously employed to describe the onset of diffusive charge dynamics and of the electrode polarization in ion conducting materials. Based on the analysis of the permittivity spectra, we demonstrate that the conductivity relaxation process provides information on ion diffusion and the magnitude of cross-correlation effects between ionic motions. A new approach is introduced which is able to estimate ionic diffusivities from the characteristic times of conductivity relaxation and ion concentration without any adjustable parameters. Furthermore, this opens the venue for a deeper understanding of charge transport in concentrated and diluted electrolyte solutions.
We analyze conductivity of polymerized ionic liquids with focus on fundamental limitations hindering faster charge transport in polymer electrolytes. We emphasize that to achieve the required ionic conductivity ~10 -3 S/cm in dry polymer electrolytes, a decoupling of ion transport from segmental dynamics is required. We demonstrate that two competing mechanisms control decoupling of ion transport: electrostatic interactions that dominates for small ions such Li, and elastic force that dominates for large ions. Our experimental results indeed confirm significant contribution of the elastic force to the energy barrier controlling transport of large ions. We also emphasize importance of ion-ion correlations that strongly affect charge transport (conductivity) even at the same ion diffusivity. Our analysis suggests that these correlations suppress ion conductivity in polymer electrolytes by about ten times. At the end, we formulate some ideas on design of polymer electrolytes with high ion conductivity.
physical conformation changes when exposed to an external stimulus, such as a change in temperature. Such materials have a permanent shape, but can be reshaped above a critical temperature and fixed into a temporary shape when cooled under stress to below the critical temperature. When reheated above the critical temperature (Tc, also sometimes called the triggering or switching temperature), the materials revert to the permanent shape. The current innovation involves a chemically treated (sulfonated, carboxylated, phosphonated, or other polar function group), high-temperature, semicrystalline thermoplastic poly(ether ether ketone) (Tg .140 C, Tm = 340 C) mix containing organometallic complexes (Zn++, Li+, or other metal, ammonium, or phosphonium salts), or high-temperature ionic liquids (e.g. hexafluorosilicate salt with 1-propyl-3- methyl imidazolium, Tm = 210 C) to form a network where dipolar or ionic interactions between the polymer and the low-molecular-weight or inorganic compound forms a complex that provides a physical crosslink. Hereafter, these compounds will be referred to as "additives". The polymer is semicrystalline, and the high-melt-point crystals provide a temporary crosslink that acts as a permanent crosslink just so long as the melting temperature is not exceeded. In this example case, the melting point is .340 C, and the shape memory critical temperature is between 150 and 250 C. PEEK is an engineering thermoplastic with a high Young fs modulus, nominally 3.6 GPa. An important aspect of the invention is the control of the PEEK functionalization (in this example, the sulfonation degree), and the thermal properties (i.e. melting point) of the additive, which determines the switching temperature. Because the compound is thermoplastic, it can be formed into the "permanent" shape by conventional plastics processing operations. In addition, the compound may be covalently cross - linked after forming the permanent shape by S-PEEK by applying ionizing radiation ( radiation, neutrons), or by chemical crosslinking to form a covalent permanent network. With respect to other shape memory polymers, this invention is novel in that it describes the use of a thermoplastic composition that can be thermally molded or solution-cast into complex "permanent" shapes, and then reheated or redissolved and recast from solution to prepare another shape. It is also unique in that the shape memory behavior is provided by a non-polymer additive.