Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “distributed processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92

Solidification of SRPPF Aqueous Recovery Liquid: Process Disruptions

Savannah River National Laboratory has identified a magnesium oxysulfate grout formulation to solidify the liquid effluent from the Savannah River Plutonium Processing Facility (SRPPF) Aqueous Recovery System (ARS). The formulation uses reactive, light burnt MgO, anhydrous MgSO 4 , and dead burnt MgO and provides good mixability, similar density to the original Portland Cement-based mix, and a leachate pH of 9.39, within the assumed Waste Isolation Pilot Plant (WIPP) brine pH range. The formulation will solidify the effluent using a solid first, lost paddle design, within a 55-gallon drum. A series of seven different process disruptions, or irregular processing during the expected ARS liquid effluent solidification process, were completed to assess the severity of the impact of the process disruption and how the formulation behaves under these conditions. Seven process disruptions were investigated including: No Mixing, Partial Mixing, Compacted/Stratified, Sealed, Overfilled, Underfilled, and Undermixed. The impact on solidification, leachate pH, Er (a Pu/Am surrogate) distribution, and density of the resulting grout were established. Overall, four of the process disruptions, No Mixing, Partial Mixing, Compacted/Stratified, and Overfilled, resulted in basic, unabsorbed liquid that would require additional solidification to be acceptable for WIPP. Most solids generated in this testing met the expected WIPP leachate pH requirements. Solids from the Compacted/Stratified process disruption test, however, produced a leachate pH slightly above the assumed range in the WIPP performance assessment. The distribution of Er for most of the tests was relatively consistent. The No Mixing process disruption test, however, resulted in non-homogeneous Er distribution, indicating that radioactive material would not be evenly distributed throughout this solid’s matrix. The Overfilled test is the only mix with a density slightly below the acceptable value. The Sealed and Overmixed tests produced a solid closest to the standard mix with no unabsorbed liquid, expected leachate pH levels, consistent Er concentrations, and expected density, indicating these process disruptions do not have a negative impact on the final grout form. Based on the other process disruptions, it is critical to have premixed dry materials and a well-defined mixing process to produce a solid, homogeneous magnesium oxysulfate cement, with no unabsorbed liquid. These process disruption tests show that the lack of adequate mixing is fundamental to creating an improperly solidified material that may require remediation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Experimental sloshing pressure impacts in ensemble domain: Transient and stationary statistical characteristics

The present paper focuses on the analysis of impact pressure registrations from repeated model scale sloshing experiments under harmonic rotational excitation. A series of more than 100 experiments, each one encompassing more than 100 impact events, has been conducted seeking the highest feasible repeatability. Different excitation periods, that cover the main features of the impact dynamics, have been considered in a preliminary screening, describing the main features of the impact dynamics. Since, even under a nominally deterministic excitation, the pressure at each impact is characterized by a high variability, a statistical approach is used treating the impact pressure as a stochastic process. For one selected excitation period, the statistical analysis focuses on the ensemble distribution of the maximum pressure during each impact event. Particular attention is given to the evolution of such distributions, in order to detect the variations in the statistical characteristics of the process. This is achieved by, first, identifying the presence and the length of the transient phase and, second, by characterizing the process at stationary state. The statistics of impact pressure for different peaks are discussed mostly in the ensemble domain. Linking the latter with the time domain analysis is made by checking that the problem can be considered “practically ergodic.” The “practical ergodicity” of the process is dealt with by checking to what extent steady state ensemble statistical information can be obtained from a single long run experiment. Statistical checks for correlation and independence of maximum impact pressures are also carried out to test the hypothesis of independent identically distributed random variables. The method of analysis presented in this paper through the considered example case is general in nature and is considered to be highly portable. In particular, it is considered to allow for a more thorough understanding of non-deterministic events such as those considered herein, by looking at them from a sound statistical perspective. The thorough description of the whole experimental setup makes the presented data suitable for comparison purposes and for validation of theoretical/numerical approaches.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Challenges for the CMS computing model in the first year

CMS is in the process of commissioning a complex detector and a globally distributed computing infrastructure simultaneously. This represents a unique challenge. Even at the beginning there is not sufficient analysis or organized processing resources at CERN alone. In this presentation we discuss the unique computing challenges CMS expects to face during the first year of running and how they influence the baseline computing model decisions. During the early accelerator commissioning periods, CMS will attempt to collect as many events as possible when the beam is on in order to provide adequate early commissioning data. Some of these plans involve overdriving the Tier-0 infrastructure during data collection with recovery when the beam is off. In addition to the larger number of triggered events, there will be pressure in the first year to collect and analyze more complete data formats as the summarized formats mature. The large event formats impact the required storage, bandwidth, and processing capacity across all the computing centers. While the understanding of the detector and the event selections is being improved, there will likely be a larger number of reconstruction passes and skims performed by both central operations and individual users. We discuss how these additional stresses impact the allocation of resources and the changes from the baseline computing model.

99 GENERAL AND MISCELLANEOUS↗

Power law and exponential ejecta size distributions from the dynamic fragmentation of shock-loaded Cu and Sn metals under melt conditions

Large scale molecular dynamics (MD) simulations are performed to study and to model the ejecta production from the dynamic fragmentation of shock-loaded metals under melt conditions. A generic 3D crystal in contact with vacuum containing about 10{sup 8} atoms and with a sinusoidal free surface roughness is shock loaded so as to undergo a solid-liquid phase change on shock. The reflection of the shock wave at the interface metal/vacuum gives rise to the ejection of 2D jets/sheets of atoms (Richtmyer-Meshkov instabilities in the continuum limit), which develop and break up, forming ejecta (fragments) of different volumes (or mass). The fragmentation process is investigated by analyzing the evolution of the resulting volume distribution of the ejecta as a function of time. Two metals are studied (Cu and Sn) and the amplitude of the roughness is varied. The simulations show that the associated distributions exhibit a generic behavior with the sum of two distinct terms of varying weight, following the expansion rate of the jets: in the small size limit, the distribution obeys a power law dependence with an exponent equal to 1.15 ± 0.08; and in the large size limit, it obeys an exponential form. These two components are interpreted, with the help of additional simple simulations, as the signature of two different basic mechanisms of fragmentation. The power law dependence results from the fragmentation of a 2D network of ligaments arranged following a fractal (scale free) geometry and generated when the sheets of liquid metal expand and tear. The exponential distribution results from a 1D Poisson fragmentation process of the largest ligaments previously generated. Unlike the power law distribution, it is governed by a characteristic length scale, which may be provided by energy balance principle.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Observations of particle number size distributions and new particle formation in six Indian locations

Atmospheric new particle formation (NPF) is a crucial process driving aerosol number concentrations in the atmosphere; it can significantly impact the evolution of atmospheric aerosol and cloud processes. This study analyses at least 1 year of asynchronous particle number size distributions from six different locations in India. We also analyze the frequency of NPF and its contribution to cloud condensation nuclei (CCN) concentrations. We found that the NPF frequency has a considerable seasonal variability. At the measurement sites analyzed in this study, NPF frequently occurs in March–May (pre-monsoon, about 21% of the days) and is the least common in October–November (post-monsoon, about 7% of the days). Considering the NPF events in all locations, the particle formation rate (J SDS ) varied by more than 2 orders of magnitude (0.001–0.6 cm –3 s –1 ) and the growth rate between the smallest detectable size and 25nm (GR SDS-25nm ) by about 3 orders of magnitude (0.2–17.2nm h –1 ). We found that J SDS was higher by nearly 1 order of magnitude during NPF events in urban areas than mountain sites. GR SDS did not show a systematic difference. Our results showed that NPF events could significantly modulate the shape of particle number size distributions and CCN concentrations in India. The contribution of a given NPF event to CCN concentrations was the highest in urban locations (4.3 × 10 3 cm –3 per event and 1.2 × 10 3 cm –3 per event for 50 and 100nm, respectively) as compared to mountain background sites (2.7 × 10 3 cm –3 per event and 1.0 × 10 3 cm –3 per event, respectively). We emphasize that the physical and chemical pathways responsible for NPF and factors that control its contribution to CCN production require in situ field observations using recent advances in aerosol and its precursor gaseous measurement techniques.

54 ENVIRONMENTAL SCIENCES↗

Development of a Stochastic Infiltration Model for PPA Implementation - 19293

Performance Assessment models often require inputs representing specific hydrologic processes and properties such as infiltration, water content, groundwater flow rate, streamflow, and sediment flux. This paper details the development of a process-level infiltration model and its use in a Probabilistic Performance Assessment (PPA) model for the West Valley Site in western New York. Additionally, this paper demonstrates a method for obtaining distributions of the long-term average hydrologic processes and properties for a PA model. For this PPA, an infiltration model was developed using HELP (Hydrologic Evaluation of Landfill Performance) to evaluate the rates of infiltration, percolation, and drainage through several site soil and proposed decommissioning cover systems, as well as the volumetric water contents of each of the unsaturated layers in a modeled soil column. A particular challenge of probabilistic modeling over long periods of time is scaling parameters appropriately so that outcomes are not grossly over- or underestimated. For these models, distributions of climatic parameters such as average precipitation rate, temperature, wind speed, humidity, and solar radiation were scaled to 1000-year averages and were used to force steady-state models that predict 1000-year average infiltration rates, drainage rates, and water contents. For the HELP model, distributions were developed for the physical and hydrologic properties of each material in a given soil column or cover system, and these properties were allowed to vary stochastically along with climatic inputs. The HELP model was run 5000 times for each of seven different soil and cover systems representing various existing and proposed conditions (i.e. native soil, backfill, existing covers, and a proposed close-in-place cover). The results of the HELP model provide ranges of 1000-year average infiltration rates, drainage rates, and water contents through and within the various layers of each of the different soil and cover conditions. The model outcomes also demonstrate the effectiveness of a proposed close-in-place cover, which essentially eliminates infiltration during its operational lifetime. Following model simulation, a sensitivity analysis was performed to establish the relative importance of each stochastic input with respect to each output. The outcomes of the model simulations and the sensitivity analysis were implemented into a system-level GoldSim model via a novel sensitivity-informed nearest neighbor approach. These infiltration rates, drainage rates, and water contents are used to parameterize mixing cells within the GoldSim Contaminant Transport module, which is the primary system-level model used in the PPA. The infiltration rates are also used as boundary conditions for a stochastic groundwater flow model that is also utilized in the PPA, but not discussed in this paper. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Phenomenology of the Z boson plus jet process at NNLO

Here, we present a detailed phenomenological study of Z-boson production in association with a jet through next-to-next-to-leading order (NNLO) in perturbative QCD. Fiducial cross sections and differential distributions for both 8 TeV and 13 TeV LHC collisions are presented. We study the impact of different parton distribution functions (PDFs) on predictions for the Z + jet process. Upon inclusion of the NNLO corrections, the residual scale uncertainty is reduced such that both the total rate and the transverse momentum distributions can be used to discriminate between various PDF sets.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Wettability Effects on Primary Drainage Mechanisms and NAPL Distribution: A Pore-Scale Study

The pore-scale processes governing water drainage behavior in porous media have implications for geoscience multiphase scenarios including carbon capture and storage, contaminant site remediation, oil recovery, and vadose zone processes. However, few studies report directly observed pore-scale water drainage phenomena in 3-D soils. This knowledge gap limits our ability to verify assumptions underlying existing models and develop optimal solutions. As such, this paper utilizes synchrotron X-ray microtomography to present an experimental pore-scale examination of nonaqueous phase liquid (NAPL)/water distribution along a primary drainage front as dense NAPL was injected upward into water wetting (WW) and intermediate wetting (IW) sand-packed columns. Pore-network structures were extracted from imaged data sets and mapped onto segmented NAPL/water data sets which allowed quantitative examinations of wettability impacts on (a) the extent to which NAPL fills individual pore bodies and (b) relationships between pore size and the phase occupying the pore, with both considered as a function of distance (and capillary pressure) relative to the NAPL front. These results revealed that several hypotheses treating IW sand similarly to WW sands are simplistic. IW systems exhibited a sequence of pore filling that deviated from traditional capillary pressure-based model predictions: NAPL invades smaller pores, while larger, adjacent pores are bypassed leaving multipore residual water ganglia. NAPL pore saturations were close to 1 and did not change with capillary pressure in IW systems. Overall, the results illustrate how a relatively small change in operative contact angle alters NAPL distribution during water drainage, with important implications for geoscience multiphase flow scenarios.

58 GEOSCIENCES↗

New method for analysis of X-ray computed tomography scans of TRISO fuel forms

X-ray computed tomography (XCT) is a powerful characterization tool that has been used for examination of both tristructural-isotropic (TRISO) coated particles and fuel forms. Rapid, nondestructive imaging of complete specimens by XCT provides significant characterization advantages in both speed and comprehensiveness over traditional materialographic methods. This paper discusses a method that has been developed to analyze XCT images of pebble fuel forms containing ~18,000 TRISO particles each. The XCT images are three-dimensional with contrast based on relative x-ray transparency. In the case of TRISO fuel forms, XCT image intensity distinguishes between the high-density kernel, the medium-density SiC, and the low-density matrix and carbon layers. Image analysis software has been developed to process XCT data sets to extract spatial distribution information, including particle nearest-neighbor distances, local packing fraction, and fuel-free zone thickness in TRISO fuel forms. Finally, although this type of high-resolution XCT analysis is likely not feasible as a quality control measurement for commercial TRISO fuel, it is highly useful in generating feedback for the development of fuel form fabrication processes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Analysis of Mass Distribution of Fission Fragment in Superheavy Mass Region

Recently our FLNR theoretical group completes a calculation model to treat all reaction processes in heavy and superheavy mass region, which is so called 'Unified model'. Using a lot of available experimental data, we verify the validity of our model and establish a reliable model to describe the whole reaction process. As examples of the application of our model, we discuss two cases that are quasi-fission process and deep inelastic collision. We show the calculation results of the mass distribution of fission fragments in the reaction {sup 36}S+{sup 236}U. Also, we discuss the possibility for the production of new heavy neutron-rich nuclei in the low-energy multi-neutron transfer process.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Chiral-odd TMDs in Drell-Yan processes

We calculate the Boer-Mulders function of the pion by applying the MIT bag model, and compare the result with that from the spectator model. We then study the azimuthal asymmetries contributed by the chiral-odd transverse momentum distributions in pion-nucleon Drell-Yan process at COMPASS and in proton-proton Drell-Yan process at RHIC, J-PARC, E906 and NICA.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Simulation of reflooding on two parallel heated channel by TRACE

In case of Loss-Of-Coolant accident (LOCA) in a Boiling Water Reactor (BWR), heat generated in the nuclear fuel is not adequately removed because of the decrease of the coolant mass flow rate in the reactor core. This fact leads to an increase of the fuel temperature that can cause damage to the core and leakage of the radioactive fission products. In order to reflood the core and to discontinue the increase of temperature, an Emergency Core Cooling System (ECCS) delivers water under this kind of conditions. This study is an investigation of how the power distribution between two channels can affect the process of reflooding when the emergency water is injected from the top of the channels. The peak cladding temperature (PCT) on LOCA transient for different axial level is determined as well. A thermal-hydraulic system code TRACE has been used. A TRACE model of the two heated channels has been developed, and three hypothetical cases with different power distributions have been studied. Later, a comparison between a simulated and experimental data has been shown as well.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Methods and Experiences for Developing Abstractions for Data-intensive, Scientific Applications

Developing software for scientific applications that require the integration of diverse types of computing, instruments, and data present challenges that are distinct from commercial software. These applications require scale, and the need to integrate various programming and computational models with evolving and heterogeneous infrastructure. Pervasive and effective abstractions for distributed infrastructures are thus critical; however, the process of developing abstractions for scientific applications and infrastructures is not well understood. While theory-based approaches for system development are suited for well-defined, closed environments, they have severe limitations for designing abstractions for scientific systems and applications. The design science research (DSR) method provides the basis for designing practical systems that can handle real-world complexities at all levels. In contrast to theory-centric approaches, DSR emphasizes both practical relevance and knowledge creation by building and rigorously evaluating all artifacts. In this work, we show how DSR provides a well-defined framework for developing abstractions and middleware systems for distributed systems. Specifically, we address the critical problem of distributed resource management on heterogeneous infrastructure over a dynamic range of scales, a challenge that currently limits many scientific applications. We use the pilot-abstraction, a widely used resource management abstraction for high-performance, high throughput, big data, and streaming applications, as a case study for evaluating the DSR activities. For this purpose, we analyze the research process and artifacts produced during the design and evaluation of the pilot-abstraction. We find DSR provides a concise framework for iteratively designing and evaluating systems. Finally, we capture our experiences and formulate different lessons learned.

97 MATHEMATICS AND COMPUTING↗

An analytical phytoplankton model and its application in the tidal freshwater James River

Here, this study constructs an analytical model to understand the phytoplankton dynamics in a one-dimensional system by integrating physical and biological processes. We present an analytical solution of phytoplankton distribution along the longitudinal direction of a tidal river. The solution has two components: water age and accumulative growth. The water age represents the overall effect of physical transport due to advection, while the accumulative growth represents the accumulation of phytoplankton biomass due to biological processes during the transport. In addition, an alternative solution with nonlinear reaction term is given to account for the feedback mechanism of nonlinear processes that affect phytoplankton growth rate. The nonlinear reaction term can be also used to approximate the effect of physical mixing on phytoplankton distribution. The analytical solutions can be further used to predict the temporal variation and spatial distribution of phytoplankton along the tidal river. They also serve as a mathematical tool to unite different field phytoplankton observations. We applied the model in the Tidal Freshwater Region (TFR) of James River under different dynamic conditions and the model results match well with the observations, which validates the theory on different time scales. Furthermore, an analysis is conducted for the Local Chlorophyll-a Maximum (LCM) in the TFR. It shows that the condition for LCM is biologically controlled, but its location is regulated by river flow and river geomorphology.

54 ENVIRONMENTAL SCIENCES↗

Data-driven nonlocal model for fragmentation in the crushing of solids

A technique is proposed for reproducing particle size distributions in three-dimensional simulations of the crushing and comminution of solid materials. The method is designed to produce realistic distributions over a wide range of loading conditions, especially for small fragments. In contrast to most existing methods, the new model does not explicitly treat the small-scale process of fracture. Instead, it uses measured fragment distributions from laboratory tests as the basic material property that is incorporated into the algorithm, providing a data-driven approach. The algorithm is implemented within a nonlocal peridynamic solver, which simulates the underlying continuum mechanics and contact interactions between fragments after they are formed. Finally, the technique is illustrated in reproducing fragmentation data from drop weight testing on sandstone samples.

58 GEOSCIENCES↗

Image-Based Fracture Surface Defect Characterization Methods for Additively Manufactured Ti-6Al-4V Tested in Fatigue

Abstract Fatigue initiation in additively manufactured samples/parts often occurs at processed-induced defects such as lack-of-fusion (LoF), keyhole, or other morphological/microstructural defects that have unique characteristics and measurable qualities. Attempts at identifying and minimizing such defects have utilized optimized processing conditions along with in situ and ex situ characterization that includes metallography and/or X-ray computed tomography (XCT). This paper highlights the benefits of using fracture surface analyses to detect and quantify defects that may not be detected by metallography/XCT due to sectioning and resolution limits. In addition to using manual quantification of fatigue initiating LoF and keyhole defects on fracture surfaces, image-based machine learning using convolutional neural networks such as U-Net were also used to automate the process. Statistical analyses were used to identify the extreme cases of defects that initiated and accelerated fatigue and to model the distribution of defect size and shape characteristics to distinguish the type of defect. Initial results show agreement between trained machine learning models and ground truth data in defect segmentation, and the distributions of defect characteristics are distinguishable to particular process-induced defect types.

Materials Science↗

Computation of Ion Charge State Distributions After Inner-Shell Ionization In Ne, Ar And Kr Atoms Using Monte Carlo Simulation

Atomic reorganization starts by filling the initially inner-shell vacancy by a radiative transition (x-ray) or by a non-radiative transition (Auger and Coster-Kronig processes). New vacancies created during this atomic reorganization may in turn be filled by further radiative and non-radiative transitions until all vacancies reach the outermost occupied shells. The production of inner-shell vacancy in an atom and the de-excitation decays through radiative and non-radiative transitions may result in a change of the atomic potential; this change leads to the emission of an additional electron in the continuum (electron shake-off processes). In the present work, the ion charge state distributions (CSD) and mean atomic charge ions produced from inner-shell vacancy de-excitation decay are calculated for neutral Ne, Ar and Kr atoms. The calculations are carried out using Monte Carlo (MC) technique to simulate the cascade development after primary vacancy production. The radiative and non-radiative transitions for each vacancy are calculated in the simulation. In addition, the change of transition energies and transition rates due to multi vacancies produced in the atomic configurations through the cascade development are considered in the present work. It is found that considering the electron shake--off process and closing of non-allowed non-radiative channels improves the results of both charge state distributions (CSD) and average charge state. To check the validity of the present calculations, the results obtained are compared with available theoretical and experimental data. The present results are found to agree well with the available theoretical and experimental values.

36 MATERIALS SCIENCE↗