Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “calculation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92

The reduced detailed configuration accounting (RDCA) model for the NLTE plasma special calculations

The purpose of this work is to continue development of a model to provide a fast and accurate in-line NLTE capability for calculating plasma spectral properties in large-scale radiation-transport hydrodynamic simulations. A method has recently been developed to transform the large detailed atomic models into very small models that can be used for fast in-line calculations. The reduced model is more accurate than the average-atom models conventionally used in such simulations. In the present work, spectra calculated with the reduced model are compared to the original detailed model and the average-atom model. The spectra of iron and gold plasmas under various plasma conditions are compared.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Patient-Specific Monte Carlo Dose Calculations for High-Dose-Rate Endorectal Brachytherapy With Shielded Intracavitary Applicator

Purpose: An integrated software platform was developed to perform a patient-specific dosimetric study on high-dose-rate {sup 192}Ir endorectal brachytherapy. Monte Carlo techniques were used to examine the perturbation effects of an eight-channel intracavitary applicator with shielding and a liquid-inflatable balloon. Such effects are ignored in conventional treatment planning systems that assume water-equivalent geometries. Methods and Materials: A total of 40 Task Group 43-based rectal patient plans were calculated using the PTRAN{sub C}T Monte Carlo photon transport code. The silicone applicator, tungsten or lead shielding, contrast solution-filled balloon, and patient anatomy were included in the simulations. The dose to water and dose to medium were scored separately. The effects of heterogeneities and uncertainties in source positioning were examined. A superposition calculation method using pregenerated Monte Carlo dose distributions about the shielded applicator in water was developed and validated for efficient treatment planning purposes. Results: On average, metal shielding decreases the mean dose to the contralateral normal tissues by 24% and reduces the target volume covered by the prescribed dose from 97% to 94%. Tissue heterogeneities contribute to dose differences of <1% relative to the prescribed dose. The differences in the dose volume indices between dose to water and dose to medium-based calculations were <1% for soft tissues, <2% for bone marrow, and >20% for cortical bone. A longitudinal shift of {+-}2.5 mm and a rotational shift of {+-}15{sup o} in applicator insertion reduced the target volume receiving the prescribed dose by {<=}4%. Conclusion: The shielded applicator improved dose conformity and normal tissue sparing; however, Task Group 43-based treatment planning might compromise target coverage by not accounting for shielding.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Craniocaudal Safety Margin Calculation Based on Interfractional Changes in Tumor Motion in Lung SBRT Assessed With an EPID in Cine Mode

Purpose: To evaluate setup error and interfractional changes in tumor motion magnitude using an electric portal imaging device in cine mode (EPID cine) during the course of stereotactic body radiation therapy (SBRT) for non-small-cell lung cancer (NSCLC) and to calculate margins to compensate for these variations. Materials and Methods: Subjects were 28 patients with Stage I NSCLC who underwent SBRT. Respiratory-correlated four-dimensional computed tomography (4D-CT) at simulation was binned into 10 respiratory phases, which provided average intensity projection CT data sets (AIP). On 4D-CT, peak-to-peak motion of the tumor (M-4DCT) in the craniocaudal direction was assessed and the tumor center (mean tumor position [MTP]) of the AIP (MTP-4DCT) was determined. At treatment, the tumor on cone beam CT was registered to that on AIP for patient setup. During three sessions of irradiation, peak-to-peak motion of the tumor (M-cine) and the mean tumor position (MTP-cine) were obtained using EPID cine and in-house software. Based on changes in tumor motion magnitude ( Increment M) and patient setup error ( Increment MTP), defined as differences between M-4DCT and M-cine and between MTP-4DCT and MTP-cine, a margin to compensate for these variations was calculated with Stroom's formula. Results: The means ({+-}standard deviation: SD) of M-4DCT and M-cine were 3.1 ({+-}3.4) and 4.0 ({+-}3.6) mm, respectively. The means ({+-}SD) of Increment M and Increment MTP were 0.9 ({+-}1.3) and 0.2 ({+-}2.4) mm, respectively. Internal target volume-planning target volume (ITV-PTV) margins to compensate for Increment M, Increment MTP, and both combined were 3.7, 5.2, and 6.4 mm, respectively. Conclusion: EPID cine is a useful modality for assessing interfractional variations of tumor motion. The ITV-PTV margins to compensate for these variations can be calculated.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

{sup 32}P Brachytherapy Conformal Source Model RIC-100 for High-Dose-Rate Treatment of Superficial Disease: Monte Carlo Calculations, Diode Measurements, and Clinical Implementation

Purpose: A novel {sup 32}P brachytherapy source has been in use at our institution intraoperatively for temporary radiation therapy of the spinal dura and other localized tumors. We describe the dosimetry and clinical implementation of the source. Methods and Materials: Dosimetric evaluation for the source was done with a complete set of MCNP5 Monte Carlo calculations preceding clinical implementation. In addition, the depth dose curve and dose rate were measured by use of an electron field diode to verify the Monte Carlo calculations. Calibration procedures using the diode in a custom-designed phantom to provide an absolute dose calibration and to check dose uniformity across the source area for each source before treatment were established. Results: Good agreement was established between the Monte Carlo calculations and diode measurements. Quality assurance measurements results are provided for about 100 sources used to date. Clinical source calibrations were usually within 10% of manufacturer specifications. Procedures for safe handling of the source are described. Discussion: Clinical considerations for using the source are discussed.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

The Electronic, Elastic, and Structural Properties of Ti-Pd Intermetallics and Associated Hydrides from First-Principles Calculations

Using an ab initio density functional approach, we report on the ground-state phase stabilities, enthalpies of formation, electronic, and elastic properties of the Ti-Pd alloy system. The calculated enthalpies of formation are in excellent agreement with available calorimetric data. We found a linear dependence between the calculated enthalpies of formation of several intermetallic structures and the Pd-concentration, indicating that each of these compounds has a very limited composition range. The elastic constants for many of these Ti-Pd intermetallics were calculated and analyzed. The B2 TiPd phase is found to be mechanically unstable with respect to the transformation into the monoclinic B19 structure. A series of hydrides, Ti2PdHx (x=1, 1.5, 2, 3, 4), have been investigated in terms of electronic structure, enthalpies of hydrogen absorption, and site preference of H atoms. Our results illustrate the physical mechanism for hydrogen absorption in term of the charge transfer, and explain why TiPd2 does not form a stable hydride.

08 HYDROGEN↗

Iterative diagonalization in augmented plane wave based methods in electronic structure calculations

Due to the increased computer power and advanced algorithms, quantum mechanical calculations based on Density Functional Theory are more and more widely used to solve real materials science problems. In this context large nonlinear generalized eigenvalue problems must be solved repeatedly to calculate the electronic ground state of a solid or molecule. Due to the nonlinear nature of this problem, an iterative solution of the eigenvalue problem can be more efficient provided it does not disturb the convergence of the self-consistent-field problem. The blocked Davidson method is one of the widely used and efficient schemes for that purpose, but its performance depends critically on the preconditioning, i.e. the procedure to improve the search space for an accurate solution. For more diagonally dominated problems, which appear typically for plane wave based pseudopotential calculations, the inverse of the diagonal of (H - ES) is used. However, for the more efficient 'augmented plane wave + local-orbitals' basis set this preconditioning is not sufficient due to large off-diagonal terms caused by the local orbitals. We propose a new preconditioner based on the inverse of (H - {lambda}S) and demonstrate its efficiency for real applications using both, a sequential and a parallel implementation of this algorithm into our WIEN2k code.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

On optimizing Jacobi–Davidson method for calculating eigenvalues in low dimensional structures using eight band k · p model

The paper presents two ways of improving the Jacobi–Davidson method for calculating the eigenvalues and eigenvectors described by eight-band k · p model for quantum dots and other low dimensional structures. First, the method is extended by the application of time reversal symmetry operator. This extension allows efficient calculations of the twofold degeneracy present in the multiband k · p model and other interior eigenvalues. Second, the preconditioner for the indefinite matrix which comes from the discretization of the eight band k · p Hamiltonian is presented. The construction of this preconditioner is based on physical considerations about energy band structure in the k · p model. On the basis of two real examples, it is shown that the preconditioner can significantly shorten the time needed to calculate the interior eigenvalues, despite the fact that the memory usage of the preconditioner and Hamiltionian is comparable. Finally, some technical details for implementing the eight band k · p Hamiltonian and the eigensolver are provided.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Calculating Failure Probabilities for TRISO-coated Fuel Particles using an Integral Formulation

The fundamental design for a gas-cooled reactor relies on the safe behavior of the coated particle fuel. The coating layers surrounding the fuel kernels in these spherical particles, termed the TRISO coating, act as a pressure vessel that retains fission products. The quality of the fuel reflects the number of particle failures that occur during reactor operation, where failed particles become a source for fission products that can then diffuse through the fuel element matrix. The failure probability for any batch of particles, which has traditionally been calculated using the Monte Carlo method, depends on statistical variations in design parameters and on variations in the strengths of coating layers among particles in the batch. An alternative approach to calculating failure probabilities is developed herein that uses direct numerical integration of a failure probability integral. Because this is a multiple integral where the statistically varying parameters become integration variables, a fast numerical integration approach is also developed. In sample cases analyzed involving multiple failure mechanisms, results from the integration methods agree closely with Monte Carlo results. Additionally, the fast integration approach, particularly, is shown to significantly improve efficiency of failure probability calculations. These integration methods have been implemented in the PARFUME fuel performance code along with the Monte Carlo method, where each serves to verify accuracy of the others.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Study on impact of Cr and Mo on diffusion of H in 2.25Cr1Mo steel using first-principle calculations

Chrome-molybdenum steel (2.25Cr1Mo steel) is one of the main materials of a steam generator (SG) in high-temperature reactor-pebblebed modules (HTR-PM). It is essential to analyze the source term of tritium in this material, because the behavior of tritium in a SG is important for performing source term analysis in normal and accident conditions. In this article, the diffusion behavior of H atom in 2.25Cr1Mo steel was calculated to estimate the diffusivity of tritium using first-principles density functional theory. To develop and simplify the model of hydrogen diffusion in 2.25Cr1Mo steel, the impact of Cr and Mo on the diffusion of hydrogen in bcc-Fe were first calculated, all the possible diffusion paths were considered, and the minimum energy path was obtained. The diffusion activation energy and pre-exponential factor of the diffusion coefficient were obtained from Vienna Ab initio Simulation Package combined with the climbing image-nudged elastic band method. Here the results indicate that the minimum energy path for the impurity H atom is from one tetrahedral interstitial site to an adjacent tetrahedral interstitial site. The function of the diffusion coefficient of H in 2.25Cr1Mo steel with temperature T can be expressed as D = 1.486 X 10 -7 x ($\frac{-16.350kJ/mol}{RT}$) (M2/s). The diffusion coefficient of our calculation and some of the previous experiments have an excellent quantitative agreement, which indicates the reliability of our crystalline model and the practicability of the present theoretical approach. More importantly, the computational results in this work can be treated as a good screening method to collect reasonable experimental data, which will provide a good reference for tritium source term evaluation in the SG of the HTR-PM.

36 MATERIALS SCIENCE↗

Creating an Advanced Sensor Network to calculate real-time, mass-weighted flue gas composition and air heater leakage of a coal-fired utility boiler under dynamic operating conditions

Utilization of renewable energy sources to minimize the environmental impact of energy production has changed the way utility boilers operate, requiring frequent load cycling between full load and partial loads as low as 30%. Dynamic operation of coal-fired utility boilers significantly reduces boiler efficiency when compared to steady state at full load. Data-driven plant optimization has shown success with coal-fired utility boilers under dynamic operating conditions. The purpose of this work was to create an Advanced Sensor Network (ASN) to provide more extensive real-time data to inform dynamic plant optimization of Net Unit Heat Rate (NUHR). The ASN consists of gas sampling grids in the convective pass of the boiler and downstream of the air heater. These sampling grids allow for quantification of spatial variation of flue gas within the boiler and calculation of mass-weighted composition of flue gas through the combination of composition, velocity, and temperature measurements. The comparison of O 2 between the inlet and outlet of the air heater is used to calculate air leakage in real time. Flue gas composition and air heater leakage are both important factors in boiler efficiency and NUHR. Further, the results of this work support the value of mass-weighted averages for determining flue gas composition accurately. The measurements from the ASN show increased composition stratification during dynamic operation, with an average standard deviation 38% higher than observed during steady-state operation. Air heater leakage was also observed to increase from 2.8% to 5.1% following a load change. Prior to the installation of the ASN, these data would not have been available for dynamic control. These real-time data will be leveraged to calculate and optimize for NUHR during dynamic operation in future work.

42 ENGINEERING↗

Line coupling and line mixing effects on calculated widths of symmetric-top molecules with the k-degeneracy: A theoretical study of N 2 -, O 2 -, and air-broadened lines of CH 3 I

Calculations of the N 2 -, O 2 -, and air-broadened widths, together with their temperature dependence exponents have been made for transitions of CH 3 I in the ν 5 and ν 6 bands. The calculations are based on a semi-classical line shape formalism developed by the current authors through modifying and refining the Robert-Bonamy formalism. In recent years, we have applied this formalism for linear molecules, symmetric-top molecules with inversion symmetry, and asymmetric-top molecules. For symmetric-top molecules with the k degeneracy such as CH 3 I, the formalism has a new feature. In this case, one should consider each of the CH 3 I transitions labeled by k i or f ≠ 0 as a doublet. Then, one needs to consider the effects of the line mixing process between these two components. Furthermore, comparisons of our theoretical predictions with some data available demonstrate a very reasonable agreement. Finally, we propose new experiments at higher perturber pressures that would enable one to check the theoretically calculated relaxation matrices and to extend the analysis to the inter-doublet mixing effects.

74 ATOMIC AND MOLECULAR PHYSICS↗

Low-compressibility and hard material carbon nitride imide C{sub 2}N{sub 2}(NH): First principles calculations

First principles calculations are performed to investigate the structural, mechanical, and electronic properties of C{sub 2}N{sub 2}(NH). Our calculated lattice parameters are in good agreement with the experimental data and previous theoretical values. Orthorhombic C{sub 2}N{sub 2}(NH) phase is found to be mechanically stable at an ambient pressure. Based on the calculated bulk modulus and shear modulus of polycrystalline aggregate, C{sub 2}N{sub 2}(NH) can be regarded as a potential candidate of ultra-incompressible and hard material. Furthermore, the elastic anisotropy and Debye temperatures are also discussed by investigating the elastic constants and moduli. Density of states and electronic localization function analysis show that the strong C-N covalent bond in CN{sub 4} tetrahedron is the main driving force for the high bulk and shear moduli as well as small Poisson's ratio of C{sub 2}N{sub 2}(NH). -- Graphical abstract: Contours of electronic localization function (ELF) of C{sub 2}N{sub 2}(NH) on the: (0 0 1) plane (a), (1 0 0) plane (b), an ELF of Si{sub 2}N{sub 2}(NH) on the: (0 0 1) plane (c) and (1 0 0) plane (d). Display Omitted Research highlights: The structural, mechanical, and electronic properties of C{sub 2}N{sub 2}(NH) have been studied. C{sub 2}N{sub 2}(NH) is a potential low compressible and hard material. Both C{sub 2}N{sub 2}(NH) and Si{sub 2}N{sub 2}(NH) are found to have insulating feature with large band gaps. The strong covalent C-N bonding in CN{sub 4} tetrahedrons play a key role in the incompressibility and hardness of C{sub 2}N{sub 2}(NH). The chemical bonding in these two solids is a complex mixture of covalent and ionic characters.

36 MATERIALS SCIENCE↗

Structure of AgI-doped Ge-In-S glasses: Experiment, reverse Monte Carlo modelling, and density functional calculations

We report an investigation of the structure and vibrational modes of Ge-In-S-AgI bulk glasses using X-ray diffraction, EXAFS spectroscopy, Reverse Monte-Carlo (RMC) modelling, Raman spectroscopy, and density functional theoretical (DFT) calculations. The combination of these techniques made it possible to elucidate the short- and medium-range structural order of these glasses. Data interpretation revealed that the AgI-free glass structure is composed of a network where GeS{sub 4/2} tetrahedra are linked with trigonal InS{sub 3/2} units; S{sub 3/2}Ge-GeS{sub 3/2} ethane-like species linked with InS{sub 4/2}{sup -} tetrahedra form sub-structures which are dispersed in the network structure. The addition of AgI into the Ge-In-S glassy matrix causes appreciable structural changes, enriching the Indium species with Iodine terminal atoms. The existence of trigonal species InS{sub 2/2}I and tetrahedral units InS{sub 3/2}I{sup -} and InS{sub 2/2}I{sub 2}{sup -} is compatible with the EXAFS and RMC analysis. Their vibrational properties (harmonic frequencies and Raman activities) calculated by DFT are in very good agreement with the experimental values determined by Raman spectroscopy. - Graphical abstract: Experiment (XRD, EXAFS, RMC, Raman scattering) and density functional calculations are employed to study the structure of AgI-doped Ge-In-S glasses. The role of mixed structural units as illustrated in the figure is elucidated. Highlights: Black-Right-Pointing-Pointer Doping Ge-In-S glasses with AgI causes significant changes in glass structure. Black-Right-Pointing-Pointer Experiment and DFT are combined to elucidate short- and medium-range structural order. Black-Right-Pointing-Pointer Indium atoms form both (InS{sub 4/2}){sup -} tetrahedra and InS{sub 3/2} planar triangles. Black-Right-Pointing-Pointer (InS{sub 4/2}){sup -} tetrahedra bond to (S{sub 3/2}Ge-GeS{sub 3/2}){sup 2+} ethane-like units forming neutral sub-structures. Black-Right-Pointing-Pointer Mixed chalcohalide species (InS{sub 3/2}I){sup -} offer vulnerable sites for the uptake of Ag{sup +}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Study of structural, elastic, electronic and optical properties of seven SrZrO{sub 3} phases: First-principles calculations

On the plane-wave ultrasoft pseudopotential technique based on the first-principles density functional theory (DFT), we calculated the structural, elastic, electronic and optical properties of the seven different phases of SrZrO{sub 3}. The obtained ground-state properties are in good agreement with previous experiments and calculations, which indicate that the most stable phase is orthorhombic Pnma structure. Seven phases of SrZrO{sub 3} are mechanically stable with cubic, tetragonal and orthorhombic structures. The mechanical and thermodynamic properties have been obtained by using the Voigt-Reuss-Hill approach and Debye-Grueneisen model. The electronic structures and optical properties are obtained and compared with the available experimental and theoretical data. - Graphical abstract: Energy versus volume of seven phases SrZrO{sub 3} shows the Pnma phase has the minimum ground-state energy. Highlights: Black-Right-Pointing-Pointer We calculated the physical and chemical properties of seven SrZrO{sub 3} polymorphs. Black-Right-Pointing-Pointer The order of stability is Pnma>Imma>Cmcm>I4/mcm>P4/mbm>P4mm>Pm3-bar m. Black-Right-Pointing-Pointer The most stable phase is orthorhombic Pnma structure. Black-Right-Pointing-Pointer Seven phases of SrZrO{sub 3} are mechanically stable. Black-Right-Pointing-Pointer The relationship between n and {rho}{sub m} is n=1+0.18{rho}{sub m}.

36 MATERIALS SCIENCE↗

Thermoelectric and thermodynamic properties of half-Heulser alloy YPdSb from first principles calculations

The structural, electronic, thermoelectric and thermodynamic properties of ternary half-Heusler compound YPdSb are investigated using the first principle calculations. It is found that YPdSb is an indirect semiconductor. The calculated band gap is 0.161 eV with spin-orbital coupling including and 0.235 eV without spin-orbital coupling including, respectively. The electronic transport properties are obtained via Boltzman transport theory. The predicted Seebeck coefficient is 240 {mu}V/K and the thermoelectric performance can be optimized by n-type doping at room temperature. Moreover, the lattice dynamical results regarding the phonon dispersion curves, phonon density of states and thermodynamic properties are reported. Thermodynamics (heat capacity and Debye temperature) as well as mean phonon free path and the thermal conductivity in a temperature range of 0-300 K are determined. - Graphical Abstract: (a) The dependence of the Seebeck coefficient on chemical potential at 300 K. (b) The dependence of the thermopower factor on chemical potential at 300 K. Highlights: Black-Right-Pointing-Pointer The Seebeck coefficient and the thermopower factor are calculated. Black-Right-Pointing-Pointer The lattice dynamics and thermodynamic properties are obtained.

36 MATERIALS SCIENCE↗

New quinternary selenides: Syntheses, characterizations, and electronic structure calculations

Five quinternary selenides, Sr₂.₆₃Y₀.₃₇Ge₀.₆₃Sb₂.₃₇Se₈ (I), Sr₂.₆₃La₀.₃₇Ge₀.₆₃Sb₂.₃₇Se₈ (II), Sr₂.₇₁La₀.₂₉Sn₀.₇₇Bi₂.₂₃Se₈ (III), Ba₂.₆₇ La₀.₃₃ Sn₀.₆₇Sb₂.₃₃Se₈ (IV), and Ba₂.₆₇ La₀.₃₃Sn₀.₆₇Bi₂.₃₃Se₈ (V), were synthesized by solid-state reaction in fused silica tubes. These compounds are isostructural and crystallize in the Sr₃GeSb₂Se₈ structural-type, which belongs to the orthorhombic space group Pnma (no. 62). Three structural units, 1 ∞ [MSe₃], 1 ∞ [M₄Se₁₀] (M=Tt, Pn) and M´ (M´=groups II and III element), comprise the entire one-dimensional structure, separated by M´. Measurements of electronic resistivity and diffused reflectance suggest that IV and V have semiconducting properties. Electronic structure calculations confirm the site preferences of Sr/La element discovered by crystal structure refinement. - Graphical abstract: Quinternary selenides Ae₂.₆₇M₀.₃₃Tt₀.₆₇Pn₂.₃₃Se₈ (Ae, M, Tt, Pn=Sr/Ba, Y/La, Ge/Sn, Sb/Bi) were synthesized and their site preferences were characterized by single-crystal X-ray diffraction and electronic structure calculation. Highlights: • Five new quinternary selenides were synthesized and characterized. • Structural units, 1 ∞ [MSe₃] and 1 ∞ [M₄Se₁₀] (M=Tt, Pn), construct the one-dimensional structure. • Calculations of electronic structure confirm site preference of Sr/La sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NbF{sub 5} and TaF{sub 5}: Assignment of {sup 19}F NMR resonances and chemical bond analysis from GIPAW calculations

The {sup 19}F isotropic chemical shifts (δ{sub iso}) of two isomorphic compounds, NbF{sub 5} and TaF{sub 5}, which involve six nonequivalent fluorine sites, have been experimentally determined from the reconstruction of 1D {sup 19}F MAS NMR spectra. In parallel, the corresponding {sup 19}F chemical shielding tensors have been calculated using the GIPAW method for both experimental and DFT-optimized structures. Furthermore, the [M{sub 4}F{sub 20}] units of NbF{sub 5} and TaF{sub 5} being held together by van der Waals interactions, the relevance of Grimme corrections to the DFT optimization processes has been evaluated. However, the semi-empirical dispersion correction term introduced by such a method does not show any significant improvement. Nonetheless, a complete and convincing assignment of the {sup 19}F NMR lines of NbF{sub 5} and TaF{sub 5} is obtained, ensured by the linearity between experimental {sup 19}F δ{sub iso} values and calculated {sup 19}F isotropic chemical shielding σ{sub iso} values. The effects of the geometry optimizations have been carefully analyzed, confirming among other matters, the inaccuracy of the experimental structure of NbF{sub 5}. The relationships between the fluorine chemical shifts, the nature of the fluorine atoms (bridging or terminal), the position of the terminal ones (opposite or perpendicular to the bridging ones), the fluorine charges, the ionicity and the length of the M–F bonds have been established. Additionally, for three of the {sup 19}F NMR lines of NbF{sub 5}, distorted multiplets, arising from {sup 1}J-coupling and residual dipolar coupling between the {sup 19}F and {sup 93}Nb nuclei, were simulated yielding to values of {sup 93}Nb–{sup 19}F {sup 1}J-coupling for the corresponding fluorine sites. - Graphical abstract: The complete assignment of the {sup 19}F NMR lines of NbF{sub 5} and TaF{sub 5} allow establishing relationships between the {sup 19}F δ{sub iso} values, the nature of the fluorine atoms (bridging or terminal), the position of the terminal ones (opposite or perpendicular to the bridging ones), the fluorine charges, the ionicity and the length of the M–F bonds. Display Omitted - Highlights: • The {sup 19}F δ{sub iso} values of NbF{sub 5} and TaF{sub 5} have been determined. • The {sup 19}F chemical shielding tensors have been calculated using the GIPAW method. • A confident assignment of the {sup 19}F NMR lines of NbF{sub 5} and TaF{sub 5} is obtained. • The relationships between the {sup 19}Fδ{sub iso} values and the M–F bonds features are established.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis, structure, and electronic structure calculation of a new centrosymmetric borate Pb{sub 2}O[BO{sub 2}(OH)] based on anion-centered OPb{sub 4} tetrahedra

The synthesis, structure, and characterization of a new centrosymmetric borate Pb{sub 2}O[BO{sub 2}(OH)] based on anion-centered OPb{sub 4} tetrahedra are reported. Pb{sub 2}O[BO{sub 2}(OH)] crystallizes in monoclinic space group C2/m with a=12.725(7) Å, b=5.698(3) Å, c=7.344(4) Å, β=116.277(6)°. The electronic band structure and density of states of Pb{sub 2}O[BO{sub 2}(OH)] have been calculated via the density functional theory (DFT). Electron density difference calculation indicates that lone-pair electrons of Pb{sup 2+} cation should be stereoactive. - Graphical abstract: An indirect gap compound of Pb{sub 2}O[BO{sub 2}(OH)] with 2D inorganic layers motif based on OPb{sub 4} tetrahedra has been synthesized and full characterized by crystallographic, IR, TG, UV–vis-NIR Diffuse Reflectance, and theoretical calculations. Display Omitted - Highlights: • A centrosymmetric borate Pb{sub 2}O[BO{sub 2}(OH)] was synthesized and characterized. • The crystalstructure, electronic band and density states was analyzed. • The lone-pair electrons of Pb{sup 2+} were proved to be stereoactive.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗