Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solubility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92

Simulated Waste Testing Of Glycolate Impacts On The 2H-Evaporator System

Glycolic acid is being studied as a total or partial replacement for formic acid in the Defense Waste Processing Facility (DWPF) feed preparation process. After implementation, the recycle stream from DWPF back to the high-level waste tank farm will contain soluble sodium glycolate. Most of the potential impacts of glycolate in the tank farm were addressed via a literature review, but several outstanding issues remained. This report documents the non-radioactive simulant tests impacts of glycolate on storage and evaporation of Savannah River Site high-level waste. The testing for which non-radioactive simulants could be used involved the following: the partitioning of glycolate into the evaporator condensate, the impacts of glycolate on metal solubility, and the impacts of glycolate on the formation and dissolution of sodium aluminosilicate scale within the evaporator. The following are among the conclusions from this work: Evaporator condensate did not contain appreciable amounts of glycolate anion. Of all tests, the highest glycolate concentration in the evaporator condensate was 0.38 mg/L. A significant portion of the tests had glycolate concentration in the condensate at less than the limit of quantification (0.1 mg/L). At ambient conditions, evaporator testing did not show significant effects of glycolate on the soluble components in the evaporator concentrates. Testing with sodalite solids and silicon containing solutions did not show significant effects of glycolate on sodium aluminosilicate formation or dissolution.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Results of stainless steel canister corrosion studies and environmental sample investigations

This progress report describes work being done at Sandia National Laboratories (SNL) to assess the localized corrosion performance of container/cask materials used in the interim storage of used nuclear fuel. The work involves both characterization of the potential physical and chemical environment on the surface of the storage canisters and how it might evolve through time, and testing to evaluate performance of the canister materials under anticipated storage conditions. To evaluate the potential environment on the surface of the canisters, SNL is working with the Electric Power Research Institute (EPRI) to collect and analyze dust samples from the surface of in-service SNF storage canisters. In FY 13, SNL analyzed samples from the Calvert Cliffs Independent Spent Fuel Storage Installation (ISFSI); here, results are presented for samples collected from two additional near-marine ISFSI sites, Hope Creek NJ, and Diablo Canyon CA. The Hope Creek site is located on the shores of the Delaware River within the tidal zone; the water is brackish and wave action is normally minor. The Diablo Canyon site is located on a rocky Pacific Ocean shoreline with breaking waves. Two types of samples were collected: SaltSmart™ samples, which leach the soluble salts from a known surface area of the canister, and dry pad samples, which collected a surface salt and dust using a swipe method with a mildly abrasive ScotchBrite™ pad. The dry samples were used to characterize the mineralogy and texture of the soluble and insoluble components in the dust via microanalytical techniques, including mapping X-ray Fluorescence spectroscopy and Scanning Electron Microscopy. For both Hope Creek and Diablo Canyon canisters, dust loadings were much higher on the flat upper surfaces of the canisters than on the vertical sides. Maximum dust sizes collected at both sites were slightly larger than 20 μm, but Phragmites grass seeds ~1 mm in size, were observed on the tops of the Hope Creek canisters. At both sites, the surface dust could be divided into fractions generated by manufacturing processes and by natural processes. The fraction from manufacturing processes consisted of variably-oxidized angular and spherical particles of stainless steel and iron, generated by machining and welding/cutting processes, respectively. Dust from natural sources consisted largely of detrital quartz and aluminosilicates (feldspars and clays) at both sites. At Hope Creek, soluble salts were dominated by sulfates and nitrates, mostly of calcium. Chloride was a trace component and the only chloride mineral observed by SEM was NaCl. Chloride surface loads measured by the Saltsmart™ sensors were very low, less than 60 mg m –2 on the canister top, and less than 10 mg m –2 on the canister sides. At Diablo Canyon, sea-salt aggregates of NaCl and Mg-SO 4 , with minor K and Ca, were abundant in the dust, in some cases dominating the observed dust assemblage. Measured Saltsmart™ chloride surface loads were very low (<5 mg m –2 ); however, high canister surface temperatures damaged the Saltsmart™ sensors, and, in view of the SEM observations of abundant sea-salts on the package surfaces, the measured surface loads may not be valid. Moreover, the more heavily-loaded canister tops at Diablo Canyon were not sampled with the Saltsmart™ sensors. The observed low surface loads do not preclude chloride-induced stress corrosion cracking (CISCC) at either site, because (1) the measured data may not be valid for the Diablo Canyon canisters; (2) the surface coverage was not complete (for instance, the 45º offset between the outlet and inlet vents means that near-inlet areas, likely to have heavier dust and salt loads, were not sampled); and (3) CISCC has been experimentally been observed at salt loads as low as 5-8 mg/m 2 . Experimental efforts at SNL to assess corrosion of interim storage canister materials include three tasks in FY14. First, a full-diameter canister mockup, made using materials and techniques identical to those used to make interim storage canisters, was designed and ordered from Ranor Inc., a cask vendor for Areva/TN. The mockup will be delivered prior to the end of FY14, and will be used for evaluating weld residual stresses and degrees of sensitization for typical interim storage canister welds. Following weld characterization, the mockup will be sectioned and provided to participating organizations for corrosion testing purposes. A test plan is being developed for these efforts. In a second task, experimental work was carried out to evaluate crevice corrosion of 304SS in the presence of limited reactants, as would be present on a dustcovered storage canister. This work tests the theory that limited salt loads will limit corrosion penetration over time, and is a continuation of work carried out in FY13. Laser confocal microscopy was utilized to assess the volume and depth of corrosion pits formed during the crevice corrosion tests. Results indicate that for the duration of the current experiments (100 days), no stifling of corrosion occurred due to limitations in the amount of reactants present at three different salt loadings. Finally, work has been carried out this year perfecting an instrument for depositing sea-salts onto metal surfaces for atmospheric corrosion testing purposes. The system uses an X-Y plotter system with a commercial airbrush, and deposition is monitored with a quartz crystal microbalance. The system is capable of depositing very even salt loadings, even at very low total deposition rates.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Analysis of Dust Samples Collected from an Unused Spent Nuclear Fuel Interim Storage Container at Hope Creek, Delaware

In July, 2014, the Electric Power Research Institute and industry partners sampled dust on the surface of an unused canister that had been stored in an overpack at the Hope Creek Nuclear Generating Station for approximately one year. The foreign material exclusion (FME) cover that had been on the top of the canister during storage, and a second recently-removed FME cover, were also sampled. This report summarizes the results of analyses of dust samples collected from the unused Hope Creek canister and the FME covers. Both wet and dry samples of the dust/salts were collected, using SaltSmart(TM) sensors and Scotch-Brite(TM) abrasive pads, respectively. The SaltSmart(TM) samples were leached and the leachate analyzed chemically to determine the composition and surface load per unit area of soluble salts present on the canister surface. The dry pad samples were analyzed by X-ray fluorescence and by scanning electron microscopy to determine dust texture and mineralogy; and by leaching and chemical analysis to deter mine soluble salt compositions. The analyses showed that the dominant particles on the canister surface were stainless steel particles, generated during manufacturing of the canister. Sparse environmentally - derived silicates and aluminosilicates were also present. Salt phases were sparse, and consisted of mostly of sulfates with rare nitrates and chlorides. On the FME covers, the dusts were mostly silicates/aluminosilicates; the soluble salts were consistent with those on the canister surface, and were dominantly sulfates. It should be noted that the FME covers were w ashed by rain prior to sampling, which had an unknown effect of the measured salt loads and compositions. Sulfate salts dominated the assemblages on the canister and FME surfaces, and included Ca-SO 4 , but also Na-SO 4 , K-SO 4 , and Na-Al-SO 4 . It is likely that these salts were formed by particle - gas conversion reactions, either prior to, or after, deposition. These reactions involve reaction of carbonate, chloride, or nitrate salts with at mospheric SO 2 , sulfuric acid, or a mmonium sulfate to form sulfate minerals. The Na-Al-SO 4 phase is unusual, and may have formed by reaction of Na-Al containing phases in aluminum smelter emissions with SO 2 , also present in smelter emissions. An aluminum smelter is located in Camden, NJ, 40 miles NE of the Hope Creek Site.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The CPA Equation of State and an Activity Coefficient Model for Accurate Molar Enthalpy Calculations of Mixtures with Carbon Dioxide and Water/Brine

Thermodynamic property calculations of mixtures containing carbon dioxide (CO 2 ) and water, including brines, are essential in theoretical models of many natural and industrial processes. The properties of greatest practical interest are density, solubility, and enthalpy. Many models for density and solubility calculations have been presented in the literature, but there exists only one study, by Spycher and Pruess, that has compared theoretical molar enthalpy predictions with experimental data. In this report, we recommend two different models for enthalpy calculations: the CPA equation of state by Li and Firoozabadi, and the CO 2 activity coefficient model by Duan and Sun. We show that the CPA equation of state, which has been demonstrated to provide good agreement with density and solubility data, also accurately calculates molar enthalpies of pure CO 2 , pure water, and both CO 2 -rich and aqueous (H 2 O-rich) mixtures of the two species. It is applicable to a wider range of conditions than the Spycher and Pruess model. In aqueous sodium chloride (NaCl) mixtures, we show that Duan and Sun’s model yields accurate results for the partial molar enthalpy of CO 2 . It can be combined with another model for the brine enthalpy to calculate the molar enthalpy of H 2 O-CO 2 -NaCl mixtures. We conclude by explaining how the CPA equation of state may be modified to further improve agreement with experiments. This generalized CPA is the basis of our future work on this topic.

02 PETROLEUM↗

Discovering the desirable alleles contributing to the lignocellulosic biomass traits in saccharum germplasm collections for energy cane improvement

Phenotyping Methods: The accessions (which includes 21 taxa and 1,177 accessions) in the World Collection of Sugarcane and Related Grasses (WCSRG) was evaluated for the following traits: arenchyma, internode length and diameter, pubescence, pith, Brix, stalk number and fiber. A core of 300 accessions that included each species in the World Collection was selected by using the Maximization Strategy in MStrat software. Results: The core had a higher diversity rating than random selections of 300 accessions. The Shannon–Weaver Diversity Index scores of the core and whole collection were similar indicating that the majority of the diversity was captured by the core collection. The ranges and medians between the core and WCSRG were similar; only two of the trait medians were not significant at P = 0.05 using the non-parametric Wilcoxon method and the coincidence rate (CR % = 96.2) was high (>80) indicating that extreme values were retained. Thus, the phenotypic diversity of these traits in the WCSRG was well represented by the core collection. Associations Methods: Genotypic and phenotypic data were collected for 1002 accessions of the WCSRG including 209 SSR markers. Association analysis was performed using both General Linear (GLM) and Maximum Likelihood (MLM) models. Different core collections with 300 accessions each were selected based on genotypic, phenotypic and combined data based on the Maximization Strategy in MStrat software. Results: A major portion of the genotyping involving SNPs is being conducted by Dr. Jianping Wang of the University of Florida under the DOE award DE-FG 02-11ER 65214 and the genotypic and phenotypic associations will be reported separately next year. In the current, study forty one and seventeen markers were found to be associated with traits using the GLM and MLM methods respectively including associations with arenchyma, internode length and diameter, pubescence, pith, and Sugar Cane Yellow Leaf Virus. The data indicates that each of the cores and the World Collection are similar to each other genotypically and phenotypically, but the core that was selected using only genotypic data was significantly different phenotypically. This indicates that there is not enough association between the genotypic and phenotypic diversity as to select using only genotypic diversity and get the full phenotypic diversity. Core Collection: Creation and Phenotyping Methods: To evaluate this germplasm for breeding purposes, a representative diversity panel selected from the WCSRG of approximately 300 accessions was planted at Canal Point, FL in three replications. These accessions were measured for stalk height and stalk number multiple times throughout the growing season and Brix and fresh biomass during harvest in 2013 and, stalk height, stalk number, stalk diameter, internode length, Brix and fresh and dry biomass was determined in the ratoon crop harvest in 2014. Results: In correlations of multiple measurements, there were higher correlations for early measurements of stalk number and stalk height with harvest traits like Brix and fresh weight. Hybrids had higher fresh mass and Brix while Saccharum spontaneum had higher stalk number and dry mass. The heritability of hybrid mass traits was lower in the ratoon crop. According to the principal component analysis, the diversity panel was divided into two groups. One group had accessions with high stalk number and high dry biomass like S. spontaneum and the other groups contained accessions with higher Brix and fresh biomass like S. officinarum. Mass traits correlated with each other as expected but hybrids had lower correlations between fresh and dry mass. Stalk number and the mass traits correlated with each other except in S. spontaneum and hybrids in the first ratoon. There were 110 accessions not significantly different in Brix from the commercial sugarcane checks including 10 S. spontaneum accessions. There were 27 dry and 6 fresh mass accessions significantly higher than the commercial sugarcane checks. Core Collection: Fiber analysis Methods: A biomass sample was taken from each accession then shredded and dried. Fiber analysis was then performed on each sample. The acetyl groups, acid insoluble lignin, acid soluble lignin, arabinan, glucan, holocellulose, total lignin, structural ash, and xylan were quantified on a % fiber basis and nonstructural ash on a % total basis. Results: There were significant, but not large differences between species for holocellulose, lignin, acetyl, acid soluble lignin, nonstructural ash, and glucan. For each trait, S. spontaneum had significantly more holocellulose, glucan, lignin, and nonstructural ash and less acetyl and acid soluble lignin than the other species. In all populations, glucan and was positively correlated with holocellulose were positively correlated and glucan and and holocellulose were negatively correlated with lignin. In hybrids, internode length correlated positively with holocellulose and nonstructural ash and negatively with lignin. The heritability estimates for each of the fiber component traits is low indicating that environment is an important factor in fiber composition. Principal component analysis indicated that a large amount of diversity exists within each of the species.

09 BIOMASS FUELS↗

Development of Modified Pag (Polyalkylene Glycol) High VI High Fuel Efficient Lubricant for LDV Applications

Engine oils play a critical role in friction reduction. Improvements in engine oil technology steadily improved fuel economy as the industry moved through ILSAC GF-1 to GF-5 specifications. These improvements were influenced by changes in base oil chemistry, development of new friction modifiers and their treat levels, and the total additive package consisting of various other components. However, the improvements are incremental and further fuel consumption reduction opportunities are becoming more challenging. Polyalkylene glycol (PAG) based engine oils are being explored as a step forward for significant fuel consumption reduction. Although PAG fluids are used in many industrial applications, its application as an engine oil has been explored in a limited way. The objective of this project is to deep dive in exploring the applicability of PAG technology in engine oil, understanding the benefits, and limitations, elucidating the mechanism(s) for friction benefits, if any, and finally recommending how to address any limitations. The project was designed in four steps, starting with selection of lubricant technology, followed by friction and wear evaluations in laboratory bench tests which are relatively simple and inexpensive and also served as a screener for further evaluation. Selected formulations were chosen for more complex engine component level tests i.e., motored valvetrain friction and wear, piston ring friction using a motored single cylinder, and motored engine tests. A couple of formulations were further selected based on component level tests for engine dyno tests i.e., Sequence VID (ASTM D6709) for fuel economy, Sequence IVA (ASTM D6891) for valvetrain wear, and Sequence VG (ASTM D6593) for sludge and varnish protection. These are some of the industry standard tests required for qualifying engine oils. Out of these tests, a single PAG oil was selected for chassis roll dynamometer tests for fuel economy and emission measurements using FTP (Federal Test Procedure) metro/highway cycles. Five different PAG chemistries were selected by varying the starting alcohol, the oxide monomers (ethylene oxide, propylene oxide, or butylene oxide), capped or uncapped, homopolymer or random copolymer. All formulations contained a proprietary additive package and one which contained additional antiwear and friction modifier additives. Laboratory bench tests (Pin-on-Disk, High Frequency Reciprocating Rig (HFRR), Block-on-Ring, Mini-Traction Machine (MTM) identified formulations having friction, wear, and load carrying characteristics similar to or better than baseline GF-5 SAE 5W-20 oil. Motored valvetrain and motored piston ring friction tests showed nearly 50% friction reduction for some of the PAG formulations compared to GF-5 SAE 5W-20 oil. Motored engine tests showed up to 15% friction benefit over GF-5 SAE 5W-20 oil. It was observed that friction benefits are more related to PAG base oil chemistry than their lower viscosity compared to GF-5 SAE 5W-20 oil. Analysis of wear surfaces from laboratory bench tests and bucket tappets from motored valvetrain tests confirmed the presence of PAG molecules. The adsorption of these polar molecules is believed to be reason for friction reduction. However, the wear surfaces also had thin tribo-film derived from additive components. The tribo-film consisting of phosphates, sulfides, and molybdenum disulfide (when molybdenum additive was present) were observed for both GF-5 SAE 5W-20 and PAG fluids. However, when using PAG fluids, motored valvetrain tests showed high initial wear, which is believed to be due to delay in protective tribo-film formation. After the initial wear, the wear rate of PAG fluids was comparable to GF-5 SAE 5W-20 oil. The PAG oil containing additional antiwear and friction reducing additives showed low initial wear as expected. However, when this oil was evaluated in Sequence IVA test, it showed initially low wear comparable to GF-5 oil but wear accelerated with oil aging indicating rapid deterioration of additive components. ASTM Sequence VG test showed good sludge protection capability but failed to meet varnish rating for GF-5 requirement. Chassis roll dynamometer tests with PAG oil 15-1 showed about 1% fuel economy benefit over GF-5 SAE 5W-20 oil in EPA city cycles only and when the oil was slightly aged (500 miles). No fuel economy benefits could be observed in combined EPA metro/highway cycles. Also, no fuel economy benefit could be observed with continued (500- 10000 miles) oil aging. However, the emission level was comparable to the reference oil and was within EPA limits. Analysis of the PAG oil following tests showed low iron content although additive components were significantly degraded. The results indicate that PAG fluids have significant friction reduction potential but there are challenges with wear and varnish protection capabilities. These limitations are primarily because the selected additive components were chosen to provide a fluid with no metal content that forms little or no sulphated ash. Significant development work is needed to identify additive components compatible with PAG chemistry including their solubility in PAG oil. Miscibility of PAG fluids with mineral base oil is another challenge for oil change service. There is PAG chemistry (oil soluble PAG, OSP) which is soluble in mineral oils but the formulation explored in this investigation did not show significant friction reduction in motored engine tests. Again, highlighting the need for additive development for specific PAG chemistry. The thermal oxidation behavior of these oils has not been explored in this investigation and needs attention.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Bio-energy Alliance High-Tonnage Bio-energy Crop Production and Conversion into Conventional Fuels

Maintaining a predictable and sustainable supply of feedstock for bioenergy conversion is a major goal to facilitate the efficient transition to cellulosic biofuels. Our work provides insight into the complex interactions among agronomic, edaphic, and climatic factors that affect the sustainability of bioenergy crop yields. Our results provide science-based agronomic response measures that document how to better manage bioenergy sorghum production from planting to harvest. We show that harvest aids provide no significant benefit as a means to decrease harvest moisture or improve bioenergy yields. Our efforts to identify optimal seeding rates under varied edaphic and climatological conditions reinforce previous findings that sorghum is a resilient plant that can efficiently adapt to changing population pressures by decreasing or increasing the numbers of additional shoots or tillers – where optimal seeding rates for high biomass photoperiod sensitive sorghum is 60,000 to 70,000 seeds per acre and 100,000 to 120,000 seeds per acre for sweet varieties. Our varietal adaptability trials revealed that high biomass photoperiod sensitive energy sorghum consistently outperforms conventional photoperiod insensitive sweet sorghum and high biomass forage sorghum as the preferred bioenergy sorghum type, with combined theoretical yields of both cellulosic and fermentable water-soluble sugars producing an average yield of 1,035 gallons of EtOH per acre. Our nitrogen trials reveal that sweet sorghums produce ample amounts of water-soluble sugars with minimal increases in nitrogen inputs, and that excess nitrogen can affect minor increases in biomass yields and cellulosic sugars but decrease bioenergy quality by decreasing water-soluble sugar concentrations and increasing ash content, specifically when plant tissue nitrogen concentrations exceed 0.6 %, dry weight basis. Finally, through our growth and re-growth trials, we show that single-cut high biomass sorghum bioenergy yields significantly exceed those of multiple-cut high biomass sorghum systems. Our agronomic yield and quality data will be uploaded to the Bioenergy KDF Website before the end of February 2013, with a date for public access to be determined pending peer-reviewed publication of our findings.

09 BIOMASS FUELS↗

Dissolution of Fluoride Salts in Hanford Tank Waste

The Direct Feed High-Level Waste (DFHLW) strategy seeks to bypass the Hanford Waste Treatment and Immobilization Plant Pretreatment Facility while retaining some processing functions to maximize waste feed loading and minimize high-level waste (HLW) waste volume. The DFHLW flowsheet needs leaching, washing, and solids concentration operations either in new or existing tanks. The effectiveness and efficiency of sludge washing has a substantial impact on DST space, mission duration, and the evaporation and low-activity waste (LAW) treatment operations required by these large wash-water additions. One target species requiring washing is fluoride. The HLW glass composition limits for fluorine drive operations to dissolve fluoride-bearing salts into the LAW fraction and thereby maximize waste loading in HLW glass. The fluoride in many high-level wastes at Hanford is predominantly in the form of fluoride-salt precipitates: villiaumite (NaF), kogarkoite (Na 3 FSO 4 ), and natrophosphate (Na 7 F(PO 4 ) 2 ·19H 2 O). Fluoride produces melter off-gas that creates corrosion risk in the off-gas system piping, while the sulfate and phosphate in the fluoride double salts kogarkoite and natrophosphate can be detrimental to glass waste loading. Fluoride salts are sparingly soluble, with solubilities ranging from approximately 40 to 130 kg per kL of pure water, and the dissolution kinetics of the three fluoride salts are not well known. Unexpected delays in a tank dissolution process could be encountered as a result of the lack of information about dissolution rates. In addition, if the double salts show transient non-stoichiometric dissolution of fluoride versus phosphate or sulfate, unexpectedly high concentrations of one of these other constituents could be produced. Washington River Protection Solutions authorized Pacific Northwest National Laboratory to collect the available data for fluoride salt dissolution rate, provide a scoping estimate of dissolution time if possible, and identify gaps in the understanding and predictive capability for estimating dissolution time. Open literature and Hanford reports were reviewed to document, understand, and (where possible) evaluate limitations on fluoride salt equilibria and dissolution kinetics, including both mass transport and surface reaction rate. Scoping estimates of dissolution time were made for mass-transfer-controlled dissolution of spherical particles of fluoride salts suspended in liquid. This is not the only potential governing mechanism; dissolution could be substantially slower if the surface reaction rate (the rate of release of ions from the surface) is the controlling mechanism. When the minimum amount of water for complete dissolution is used and the slip velocity between the liquid and suspended particles is less than or equal to the terminal settling velocity, the estimated mass-transfer rates allow 0.1 mm particles of fluoride salt to dissolve in minutes at 25 °C in water containing no other dissolved salts. Much larger solids, such as the 6-mm chunks that have been seen in heels, could take a few hours to more than a week to dissolve. The actual dissolution times will depend strongly on the actual slip velocity, the extent of particle suspension, constraint by surface reaction rates, the ratio of solvent to solid, and the presence of common ions that shift the solubility equilibria to restrict dissolution of fluoride salts.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Report on the effect of dopants on FLASH sintering of enhanced UO 2

Large grained UO 2 can be achieved through the addition of dopants such as, Cr, Al, Nb and Mg. The enhanced microstructure can enable slower fission gas release that reduces pressure build up in the fuel rods and better mechanical properties that can alter the pellet cracking behavior and, therefore, limit accident prone pellet cladding loading. UO 2 fuel is sintered through conventional sintering methods that require high temperatures and long sintering times. Field assisted sintering techniques like flash sintering use current and voltage to enable sintering of ceramics at low temperatures and short times. Flash sintering has been demonstrated for sintering UO 2 to high densities. In this work, this technique has been applied to Cr-doped UO 2 to assess the feasibility of the technique for grain enhancement. Doped UO 2 samples below and above the solubility limit of Cr into UO 2 have been assessed. The results show that grain enhancement was not possible in either case and this was attributed to the low temperatures and sintering times that make flash sintering attractive. For the Cr-doped sample below or near the solubility of Cr, it is postulated that the temperatures were not high enough to actually dissolve it into solution in the UO 2 lattice. For the Cr-doped sample above the solubility limit of Cr, secondary phases were identified via SEM and EDS, as expected. Follow up work should be carried out to assess if flash sintering can produce grain enlargement for UO 2 feedstocks with dopants already in solid solution such as UO 2 produced via sol-gel or modified direct denitration method.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fundamental Studies of Tritium Diffusivity in Irradiation Defective Lithium Aluminate and Lithium Zirconates Pellets Used in TPBAR

Due to its excellent irradiation behavior at elevated temperatures, lithium aluminate (LiAlO 2 ) is used in the form of annular ceramic pellets enriched with the 6Li isotope in tritium producing burnable absorber rod (TPBAR). To simulate the nuclear characteristics and produce tritium (T), TPBAR is irradiated by a neutron flux in a pressurized water reactor (PWR). The T diffuses through the pellets and is captured by the metal getter where it chemically reacts and leads to formation of metal hydride. The transport of T in radiation damaged pellets that contain defects and impurities is not clearly understood due to the lack of fundamental studies of T solubility and diffusivity. The other candidate material possessing a similar physical and chemical properties and can be potentially useful as a tritium breading blanket in the future is Lithium Zirconates (Li 2 ZrO 3 ). In FY2017, we investigated the diffusion and solubility properties in irradiation defective LiAlO 2 and Li 2 ZrO 3 crystals with different level of tritium concentration. In FY2018 we continued to explore the diffusivity and solubility properties extensively in those candidate materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

129 I, 99 Tc, And U Distribution Coefficients of Subsurface Sediments Collected from the Proposed Site of the Environmental Management Disposal Facility

Performance Assessment calculations were completed in 2020 to evaluate the Environmental Management Disposal Facility (EMDF), a proposed new low-level radioactive waste (LLW) disposal facility on the U.S. Department of Energy’s Oak Ridge Reservation (ORR). Among the large number of input parameters needed for such calculations, are distribution coefficients (K d values; radionuclide concentration solid:liquid ratio) that provide a measure of the tendency of radionuclides to bind to sediments. The objective of this study was to measure K d values of three radionuclides that may pose a disproportionately large amount of risk, U, 129 I and 99 Tc. The average I K d value for the 14 geological materials recovered from the proposed EMDF site was 37.8 mL/g and ranged from -1.8 to 140.9 mL/g. These values were consistent, but somewhat larger than previous measurements made with ORR sediments and were about an order of magnitude greater than those used in previous EMDF PA calculations. The median Tc K d value was 365.7 mL/g, much greater than previously reported using ORR geological materials. Five of the 14 tested geological materials sorbed large quantities of Tc, suggesting that the weakly sorbing Tc(VII) species had been reduced to the sparingly soluble Tc(IV) species. The five strongly sorbing sediments had apparent Tc solubility values of approximately <10 -8 mol/L. The median U K d value was 5,726 mL/g. All of the tested geological materials had large K d values, ranging from 625 to >10,208 mL/g. Among the sediment samples that exhibited strong U binding, the apparent solubility value was approximately <10 -9 mol/L. Based on sediment properties and general ORR geological considerations, it was proposed that much of the I and Tc retention could be attributed to the site materials exhibiting low pH (average pH = 4.94), low redox status, and/or the elevated levels of iron oxides, manganese oxides, and natural organic matter. Similarly, the extremely high U binding measured in these sediments may also be attributed to the low conditions of carbonates, which can complex and therefore solubilize uranyl in these tests due to the low pH, and also the relatively high concentrations of iron and organic coatings on these samples. An implication of this study is that the areas of the EMDF subsurface environment may have natural properties for attenuating I, Tc, and U movement, and potentially other radionuclides, thereby possibly reducing risk posed by burial of LLW at this site. This document is a revision of SRNL-STI-2021-00404, Revision 0 that includes new data describing U K d values and new I and Tc K d values for four Nolichucky sediments. These new results were integrated into the data presented in the original document.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Defining the Minimal Set of Microbial Genes Required for Valorization of Lignin Biomass (Final Report)

Project Goals: Lignin is the second most abundant biopolymer on earth and represents a critically underutilized biomass resource for hydrocarbon feedstocks. Despite substantial effort, there is still no efficient process to convert lignin to useable carbon-based platform chemicals and materials. The goal of this project is identify a minimal set of microbial enzymes necessary for lignin breakdown and sufficient for the synthesis of valuable chemical intermediates from lignin isolated as a byproduct of lignocellulosic ethanol production. These genes will be then used to engineer functional whole cell biocatalysts for tunable lignin metabolism. To date, although a number of enzymes have been associated with lignin degradation, most have been tested in isolation (as individual enzymes) and on drastically different substrates -- often dyes that are not related to lignin. In contrast, lignin utilization in nature likely occurs by microbial consortia with multiple enzymes acting synergistically. We propose to examine two separate stages of lignin breakdown carried out by the microbes that do it best: (1) early breakdown of native polymeric lignin into soluble fragments by a set of sequenced wood-rotting fungal species, and (2) downstream metabolism of these soluble lignin fragments to useful chemical intermediates by a panel of sequenced soil saprophytes. Our approach involves testing sets of genes that will be assayed combinatorially in the context of a heterologous expression host. The resulting engineered strains will be systematically assayed using soluble lignin fragments, synthetic defined polymeric lignin, and finally lignin directly sourced from lignocellulosic processing streams. In addition to resulting in a functional whole cell biocatalyst for lignin utilization, we anticipate that this approach will allow us to address key unanswered questions about lignin metabolism in nature, including: (1) Why does the Trametes versicolor genome contain 25 different class II peroxidases? (2) What is the role of laccases in lignin metabolism? Why do some aggressive lignin degraders have many laccases (e.g. >7 in T. versicolor) while others have none (e.g. P. chrysosporium)? (3) How is peroxide provided in a controlled manner to drive peroxidase activity without causing the enzyme inhibition that is so often observed in vitro? (4) What strategies do microbial lignin degraders use to avoid the problem of repolymerization during active lignin degradation? and (5) Can microbial lignin metabolism be diverted for high level production of defined aromatics? A final critical question is whether combining key minimal sets of enzymes from a wide range of organisms will result in engineered strains capable of highly efficient, streamlined pathways for lignin utilization that can be tuned for a specific carbon output. This effort will leverage DOE investments in microbial genome sequencing, and secure a critical channel for lignin biomass utilization that will also help to render lignocellulosic a viable feedstock for the production of renewable liquid biofuels.

59 BASIC BIOLOGICAL SCIENCES↗

Physical, Chemical, and Mineralogical Characterizations of MSWI Ash Product and Recommendations for Downstream Processing

The primary objectives of this project are to (1) systematically characterize MSWI ash, and (2) based on characterization findings, design preliminary flowsheets for downstream processing. To achieve these objectives, a total of ten tasks were completed, including sample collection, physical separation tests, liberation tests, synthetic MSWI ash preparation, elemental composition analysis, sequential chemical extraction, mineralogical characterization, pozzolanic activity characterization, thermal stability characterization, processing flowsheet design, TEA and T2M, and project performance reporting. Many useful findings and conclusions were obtained from the exhaustive efforts of this project from several different aspects, including: a) Valuable Metals in MSWI Ash: MSWI ash contains a diverse array of valuable metals. Based on potential recoverable values, the most valuable metals present in MSWI ash include Fe, Ti, Mn, Cu, Zn, V, Co, Ni, Sr, Sn, Ag, Mo, and Sc. Some of these metals have been identified as critical minerals by DOE and DOI, suggesting that MSWI is a promising feedstock for critical mineral recovery. Noticeable graphical and seasonable variations in the valuable metal content of MSWI ash were observed. Nevertheless, it was challenging to discern any clear, definitive patterns for conclusions from those observations. Compared with bottom ash, fly ash contains more volatile metals, such as Zn and Sn, but less nonvolatile metals, such as Fe, Mn, Cu, Zn, Co, and Ni. Mineralogical analyses showed that MSWI ash contains a substantial amount of calcium minerals, such as portlandite, lime, gypsum, and calcite. In addition, it was found that different types of valuable metals often exist in the same particles. b) Physical Separation of MSWI Ash: Both dry sieving and wet sieving were performed on MSWI ash. A notable disparity in the size distribution of the same material was observed when using the two different sieving methods. The disparity is due to the agglomeration of small particles. For the valuable metals investigated, no significant enrichment in a specific size fraction was observed, suggesting that it is challenging to preconcentrate the valuable metals through size fractionation. Due to the presence of ferromagnetic materials, such as Fe, most of the materials reported to the magnetic products obtained by dry magnetic separation. However, the enrichment effect is minimal due to the existence of particle agglomerates. Density separation at a cut-off density of 2.7 SG or higher led to noticeable enrichment of selected valuable metals, particularly Ti. The unburned carbon present in MSWI ash was effectively removed by flotation using diesel as the collector. A novel reagent scheme, Na2S plus cationic collectors, that can efficiently beneficiate nonferrous metals plus Co was developed. c) Liberation Tests: The particle size of MSWI ash was effectively reduced by grinding, and as a result, the encapsulated valuable metal particles (if any) were liberated to a certain degree. However, particle size reductions did not noticeably enhance the beneficiation performance using the physical separation methods, primarily due to the inefficiency of these methods in processing fine particles and/or a possibility that insufficient liberation is not a limiting factor for achieving satisfactory physical separation performance. Valuable metals were classified into water leachable, ion-exchangeable, acid soluble, reducible, oxidable, and insoluble forms. It was found that the distributions in the different categories, i.e., the occurrence modes of the valuable metals, were not affected by the particle size. d) Leaching Characteristics of Metals from MSWI Ash: Most of the valuable metals were extracted from the fly ash samples when using 1 M HCl or HNO3 as the lixiviant. The leaching reaction is a very fast process, which can reach equilibrium within the first 5 min. The releasing of Co, Ni and Ag are sensitive to leaching temperature, a higher recovery value could be obtained when using relatively higher leaching temperatures. The leachability of the valuable metals present in MSWI bottom ash is relatively lower than that of fly ash. Leaching recoveries increased with elevations in the acid concentration. Relatively high leaching recoveries were obtained for REEs, Mn, Co, Ni, Cu, and Zn using 1 M HCl or HNO3 as the lixiviant. Elevations in the reaction temperature noticeably increased the leachability of the valuable metals, whereas the leachability was barely influenced by oxidizing and reducing agents. Similar to fly ash, leaching valuable metals from bottom ash is a rapid process, with most of the leaching reaction completed within the first 5 minutes. e) Combusted iPhones: The original structure of iPhones was remained after treating at 400 ºC and 600 ºC, while after being treated at 800℃, the screen bent, and the back cover of iPhone melted. Increasing the combustion temperature to 1000℃, the screen scattered, and most of the components turned into ashes. Combustion enhanced the leachability of REEs, while the leachability of the other valuable metals, except for Zn, was barely affected. Most of the REEs present in the original iPhones occurred as oxidizable forms. With elevations in the combustion temperature up to 600 ºC, the oxidizable REEs were transformed to acid soluble forms. However, further elevations in temperature resulted in decreases in the acid soluble fraction and corresponding increases in the reducible and oxidizable forms. Additionally, combustion temperature also significantly altered the occurrence modes of other metals present in the iPhones. f) Synthetic MSWI Ash: It was found that in the absence of hydrogen peroxide, all the elements except for Si were leached to certain degrees. It is noteworthy that approximately 80% of Zn was leached with 1.2 M HCl. When hydrogen peroxide was added to the reaction system, noticeable increases in the leaching recovery of Fe, Mn, Co, Ni, and Cu were observed. The leaching recovery of Al and Si was barely affected by adding hydrogen peroxide. These results suggested that the majority of Zn in the synthetic MSWI ash existed as metal oxide, a portion of Fe, Mn, Co, Ni, and Cu existed as metal oxide, and Al and Si are associated with glasses which are difficult to leach. Additionally, the remaining Fe, Mn, Co, Ni, and Cu in the metallic form were efficiently oxidized in the presence of hydrogen peroxide. g) Pozzolanic Activity and Thermal Stability of MSWI Ash: MSWI fly ash has higher pozzolanic activity compared to the bottom ash sample, which indicates that the fly ash sample consumed more portlandite because of its smaller particle size as reactivity fundamentally relates to reaction surface area. However, after the recovery of valuable elements, the pozzolanic activity of both the valuable elements fraction and the less valuable elements-rich products decreased significantly, which means that the valuable elements recovery lowers the Ca(OH)2 consumption, thus leading to the low activity of SCM. h) Flowsheet Design for Metal Recovery from MSWI Ash: Based on the results of the comprehensive physical separation and acid leaching tests, circuits that enable the beneficiation of the valuable metals were developed. In these circuits, the valuable metals are recovered into nonferrous, ferrous, and other valuable metal concentrates, which are processed separately in the acid leaching step. The subsequent separation and purification steps are simplified due to the physical beneficiation step. In addition, the overall recovery cost is reduced since physical beneficiation is much cheaper compared with chemical processing. Using different technologies, such as selective precipitation and solvent extraction, a comprehensive hydrometallurgical circuit was designed, and compounds of Cu, Zn, Mn, Co, and Ni with a purity close to or even higher than 95% were successfully generated.

36 MATERIALS SCIENCE↗

Studies of Helium Behavior in Uranium Hexafluoride

Several issues have arisen from experimental observations and/or theoretical postulation related to the behavior of helium in uranium hexafluoride (UF 6 ) matrices and how it may impact the ability to use this noble gas to quantify the fill date of the cylinder. A series of experiments was conducted to address several such issues, and the results and implications are reported here. Two issues relate to bias in the helium measurement due to ambient air from extraneous sources such as atmospheric air or from potential holdup in a large, activated alumina chemical trap. These issues are really a question of differential retention of helium versus three other inert gas isotopes (representative of other noble gases found in air) used as a calibration for air in leakage. Discernable bias was not detected in either case. Another issue had to do with helium potentially brought into the cylinder by a liquid UF 6 fill and subsequently released as the material solidifies and/or during storage. The solubility of helium in liquid UF 6 was measured to investigate this theory. The experiment quantified the potential magnitude of the initial helium contribution if present. The final issue was that of retention of helium in solid UF 6 . Investigation of this theory necessitated quantifying both the solubility and the diffusivity of helium in UF 6 . In one experiment, the solubility was measured at cryogenic temperature, allowing quantification of helium in solid UF 6 such as would be found in a cold trap. In a second experiment, transport of helium into and through a macroscopic plug of solid UF 6 was examined. The transport was very slight although apparently detectible. Effectively, only an upper limit to the transport could be determined, but that limit implied that helium holdup in solid UF 6 is a real possibility.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Sodium Compatibility of Advanced Materials

This report gives a description of ongoing activities in the design, fabrication, construction, and planned testing of advanced structural materials in a forced convection sodium flow loop. The work is the Argonne National Laboratory (ANL) portion of the effort on the work project entitled, "Sodium Compatibility of Advanced Fast Reactor Materials," with Oak Ridge National Laboratory (ORNL) as the technical lead and is a part of Advanced Structural Materials Program for the Advanced Fuel Cycle Initiative (AFCI) Reactor Campaign. The objective of this project is to develop information on sodium corrosion compatibility of advanced materials being considered for sodium reactor applications. This report is the third deliverable from ANL in FY09 (M3505050704) under the work package “Sodium Compatibility of Advanced Fast Reactor Materials.” An earlier report examined the thermodynamic and kinetic factors involved in the purity of liquid sodium coolant for sodium reactor applications. Available information was presented on solubility of several metallic and nonmetallic elements along with a discussion of the possible mechanisms for the accumulation of impurities in sodium. That report concluded that the solubility of many metals in sodium is low (<1 part per million) in the temperature range of interest in sodium reactors and such trace amounts would not impact the mechanical integrity of structural materials and components. The earlier report also analyzed the solubility and transport mechanisms of nonmetallic elements such as oxygen, nitrogen, carbon, and hydrogen in laboratory sodium loops and in reactor systems such as Experimental Breeder Reactor-II (EBR-II), Fast Flux Test Facility (FFTF), and Clinch River Breeder Reactor (CRBR). Among the nonmetallic elements discussed, oxygen is deemed controllable and its concentration in sodium can be maintained in sodium for long reactor life by using cold-trap method. It was concluded that among the cold-trap and getter-trap methods, the use of cold trap is sufficient to achieve oxygen concentration of the order of 1 part per million. Under these oxygen conditions in sodium, the corrosion performance of structural materials such as austenitic stainless steels and ferritic steels will be acceptable at a maximum core outlet sodium temperature of ≈550°C. In the current sodium compatibility studies, the oxygen concentration in sodium will be controlled and maintained at ≈1 ppm by controlling the cold trap temperature. Among the nonmetallic elements in sodium, carbon was assessed to have the most influence on structural materials since carbon, as an impurity, is not amenable to control and maintenance by any of the simple purification methods. The dynamic equilibrium value for carbon in sodium systems is dependent on several factors, details of which were discussed in the earlier report. Furthermore, the transport of carbon in the primary and secondary loops of the reactor system and its effect on the carburization-decarburization behavior of structural components was addressed. Based on this assessment, the current sodium compatibility studies will examine the role of carbon concentration in sodium on the carburization-decarburization of advanced structural materials at temperatures up to 650°C. Carbon will be added to the sodium by exposure of carbon-filled iron tubes, which over time will enable carbon to diffuse through iron and dissolve into sodium. The method enables addition of dissolved carbon (without carbon particulates) in sodium that is of interest for materials compatibility evaluation. The removal of carbon from the sodium will be accomplished by exposing carbon-gettering alloys such as refractory metals that have a high partitioning coefficient for carbon and also precipitate carbides, thereby decreasing the carbon concentration in sodium.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

129 I, 99 Tc, and U Distribution Coefficients of Subsurface Sediments Collected from the Proposed Site of the Environmental Management Disposal Facility

Performance Assessment calculations were completed in 2020 to evaluate the Environmental Management Disposal Facility (EMDF), a proposed new low-level radioactive waste (LLW) disposal facility on the U.S. Department of Energy’s Oak Ridge Reservation (ORR). Among the large number of input parameters needed for such calculations, are distribution coefficients (K d values; radionuclide concentration solid: liquid ratio) that provide a measure of the tendency of radionuclides to bind to sediments. The objective of this study was to measure K d values of three radionuclides that may pose a disproportionately large amount of risk, U, iodine-129 ( 129 I) and technetium-99 ( 99 Tc). The average 129 I K d value for the 14 geological materials recovered from the proposed EMDF site was 37.8 mL/g and ranged from 0.45 to 140.9 mL/g. These values were consistent, but somewhat larger than previous measurements made with ORR sediments and were about an order of magnitude greater than those used in previous EMDF PA calculations. The median 99 Tc K d value was 365.7 mL/g, much greater than previously reported using ORR geological materials. Five of the 14 tested geological materials sorbed large quantities of 99 Tc, suggesting that the weakly sorbing 99 Tc(VII) species had been reduced to the sparingly soluble 99 Tc(IV) species. The five strongly sorbing sediments had apparent 99 Tc solubility values of approximately <10 -8 mol/L. The median U K d value was 5,726 mL/g. All of the tested geological materials had large K d values, ranging from 625 to >10,208 mL/g. Among the sediment samples that exhibited strong U binding, the apparent solubility value was approximately <10 -9 mol/L. Based on sediment properties and general ORR geological considerations, it was proposed that much of the 129 I and 99 Tc retention could be attributed to the site materials exhibiting low pH (average pH = 4.94), and/or the elevated levels of iron oxides, manganese oxides, and natural organic matter. Similarly, the extremely high U binding measured in these sediments may also be attributed to the low conditions of carbonates, which can complex and therefore solubilize uranyl in these tests due to the low pH, and also the relatively high concentrations of iron and organic coatings on these samples. An implication of this study is that the areas of the EMDF subsurface environment may have natural properties for attenuating 129 I, 99 Tc, and U movement, and potentially other radionuclides, thereby possibly reducing risk posed by burial of LLW at this site.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Testing of High S Matrix Glasses to Expand DFHLW Glass Compositional Ranges (Rev.1)

Gaps in glass composition-property data for direct-feed high-level waste (DFHLW) have recently been identified. One such gap is the region of high sulfur solubility since previous, pretreated, high-level wastes contained very little sulfur. Filling this data gap will significantly broaden the range of process flowsheet options including minimal washing and will allow for optimized waste loading in DFHLW glasses. This report summarizes the data collected during the characterization of the DFHLW High S Glass Matrix (HS24). A glass matrix of 50 glass compositions was developed to evenly cover the DFHLW composition region for high sulfur glass. Matrix glasses were designed to expand the composition region outside the current component concentration and property limits so as to reduce uncertainties at the limits. The 50 matrix glasses were fabricated and tested for properties important to the success of DFHLW vitrification including: compositions, canister centerline cooling (CCC) crystallinity and isothermal crystallinity, density, viscosity, electrical conductivity (EC), product consistency test (PCT) response, toxicity, and sulfate solubility. Melter materials corrosion testing is reported elsewhere. These glasses were intentionally designed to have high SO 3 solubilities (0.7 to 2.2 SO 3 wt%) in compositional regions that had not been previously explored. Forty-eight glasses showed the measured SO 3 content retained >80% of the target SO 3 and the densities of all the glasses ranged from 2.49 g·cm -3 to 2.74 g·cm -3 . While the model predicted nepheline formation in 5 glasses, one of the tested 50 CCC glasses formed nepheline, and 35 glasses formed Cr-containing phases such as spinels and eskolaite. Only five glasses were amorphous after CCC treatment where 44 glasses with detectable crystals contained =10 wt% crystals and only one glass had > 10 wt% crystals. None of the glasses exceeded the allowable T 2% for spinel crystal formation at 950 ºC (i.e., no glasses had >2 wt% spinel at 950 ºC) during isothermal crystal fraction tests where 10 glasses showed no crystalline phases at or below 950 ºC. All the glasses (except one which failed being slightly lower than the target) satisfied the SO 3 constraint while 98 glasses did not meet the viscosity constraints and 4 failed the EC constraints. Six quenched (Q) and six CCC glasses failed the Defense Waste Processing Facility (DWPF) Environmental Assessment (EA) glass PCT threshold and 3 Q and 4 CCC failed the PCT design constraint. One glass exceeded the WTP delisting limits for Cr via EPA Method 1311 (i.e., Toxicity Characteristic Leaching Procedure, TCLP). It should be emphasized that some of these glasses were specifically designed to approach or even exceed certain property constraints, as filling data gaps in these regions will provide the greatest benefit for future model development by improving accuracy and reducing uncertainties. These insights will ultimately support the development of more robust glass formulation strategies, enabling higher waste loading, reducing operational risks, and expanding the processing envelope.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Fluorinated Glyme Solvents to Extend Lithium-Sulfur Battery Life (Final Technical Report, Unlimited)

This project investigated a number of partially fluorinated glymes (PFGs) as electrolyte cosolvents to improve the performance of lithium-sulfur (Li-S) batteries. A major issue in Li-S cells is the electrochemical reaction of sulfur in the cathode to form lithium polysulfides (LPS) that dissolve in the electrolyte. Those LPS are electrochemically and chemically reactive at the lithium anode, resulting in lithium sulfide deposition on the anode and also electrochemical reaction at both the anode and cathode, leading to a “polysulfide shuttle” and reduced coulombic efficiency (CE) and self-discharge of the cell. PFGs reduce the solubility of LPS while maintaining good solubility of lithium salts such as LiTFSI. By adjusting the amount of PFG as cosolvent in the electrolyte, we showed that the solubility of LPS in the electrolyte can be tuned. (It is not desirable to completely eliminate LPS in the electrolyte, as they facilitate electrochemical reaction of the electrically insulating S 8 and Li 2 S within the cathode by shuttling charge between them and the conductive carbon.) Another issue in Li-S cells is degradation of the Li anode over many cycles of stripping (discharge) and plating (charge). We showed that PFGs have a beneficial effect on the physical morphology of the Li anode, SEI formation, and the CE of a Li-Li cell. Among the many PFGs tested, we found the best performance from PFGs designated PFG2 and PFG5, and these two PFGs were thoroughly studied. A systematic coin-cell study of electrolyte solvents of 90:10, 80:20, or 70:30 DME:PFG (DME = 1,2-dimethoxyethane) revealed some systematic trends: a higher percentage of PFG solvent led to substantially longer cycle life, but at the same time reduced specific capacity (mAh/g(S)) and cell capacity at higher rates. These studies used LiFSI as the electrolyte salt, as it was found to extend cycle life compared to LiTFSI. Finally, the addition of a small amount of 1,3-dioxolane (DOL) to the electrolyte was found to be beneficial. The overall optimal electrolyte solution was found to be 0.6 M LiFSI + 0.5 M LiNO 3 in 75:5:20 DME/DOL/PFG (either PFG2 or PFG5).

25 ENERGY STORAGE↗