Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Shear Layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Inner Core Rotation from Geomagnetic Westward Drift and a Stationary Spherical Vortex in Earth's Core

The idea that geomagnetic westward drift indicates convective leveling of the planetary momentum gradient within Earth's core is pursued in search of a differentially rotating mean state, upon which various oscillations and secular effects might be superimposed. The desired state conforms to roughly spherical boundary conditions, minimizes dissipative interference with convective cooling in the bulk of the core, yet may aide core cooling by depositing heat in the uppermost core and lower mantle. The variational calculus of stationary dissipation applied to a spherical vortex within the core yields an interesting differential rotation profile akin to spherical Couette flow bounded by thin Hartmann layers. Four boundary conditions are required. To concentrate shear induced dissipation near the core-mantle boundary, these are taken to be: (i) no-slip at the core-mantle interface; (ii) geomagnetically estimated bulk westward flow at the base of the core-mantle boundary layer; (iii) no-slip at the inner-outer core interface; and, to describe magnetic locking of the inner core to the deep outer core, (iv) hydrodynamically stress-free at the inner-outer core boundary. By boldly assuming the axial core angular momentum anomaly to be zero, the super-rotation of the inner core is calculated to be at most 1.5 degrees per year.

Voorhies, C. V.↗
DOE OSTI2021

Exfoliation of surfactant swollen layered MWW zeolites into two-dimensional zeolite nanosheets using telechelic liquid polybutadiene

We report two-dimensional (2D) zeolites have the potential to enhance mass transport by reducing diffusion lengths and thus find applications in catalysis and separation. High aspect ratio 2D zeolite nanosheets are required for fabrication of thin, high-flux zeolite membranes. Preparation of 2D zeolite nanosheets can be achieved by exfoliation of layered zeolite precursors, which usually requires multiple steps including swelling with cationic surfactants, exfoliation by applying a mechanical force such as shearing or sonication, purification and removal of the surfactants. The exfoliation of surfactant swollen layered zeolite precursors has been studied using molten polystyrene and telechelic liquid polybutadiene, but still requires extensive shearing force. Recently, a novel one-step exfoliation method has been developed for nonswollen MWW zeolite precursors using tetrabutylammonium hydroxide (TBAOH) solution. In this work, we study the exfoliation of surfactant swollen MWW layered precursors (with and without aluminum) in commercially available liquid hydroxyl-terminated polybutadiene (HTPB) with the aim to provide fundamental understanding of the interaction between the liquid polybutadiene and the surfactant swollen layered zeolite precursors. It was found that surfactant swollen ITQ-1, (ITQ-1(S)), a pure silica layered precursor with MWW framework after being swollen with a cationic surfactant, can be exfoliated in liquid HTPB at room temperature without applying any additional shearing force. The aluminum containing surfactant swollen MWW precursors can be also exfoliated in HTPB at room temperature, but require additional shearing forces. The exfoliation process was monitored using rheology experiments and studied by tuning the composition of the zeolite precursors. The interaction between the layered zeolite precursor and the hydroxyl group of the liquid polybutadiene allows the polymer to intercalate the precursor and exfoliate it into nanosheets. The presence of framework aluminum and the nature of the organic structure directing agents (OSDAs) are key parameters affecting the exfoliation process. Framework Al is unfavorable for the exfoliation possibly due to the surface charges introduced by the aluminum. Bulky OSDA, trimethyladamantammonium (TMAda + ), in the interlayer spacing may facilitate the exfoliation.

2D nanosheets↗
NASA NTRS2000

An Assessment of Five Modeling Approaches for Thermo-Mechanical Stress Analysis of Laminated Composite Panels

A study is made of the effects of variation in the lamination and geometric parameters, and boundary conditions of multi-layered composite panels on the accuracy of the detailed response characteristics obtained by five different modeling approaches. The modeling approaches considered include four two-dimensional models, each with five parameters to characterize the deformation in the thickness direction, and a predictor-corrector approach with twelve displacement parameters. The two-dimensional models are first-order shear deformation theory, third-order theory; a theory based on trigonometric variation of the transverse shear stresses through the thickness, and a discrete layer theory. The combination of the following four key elements distinguishes the present study from previous studies reported in the literature: (1) the standard of comparison is taken to be the solutions obtained by using three-dimensional continuum models for each of the individual layers; (2) both mechanical and thermal loadings are considered; (3) boundary conditions other than simply supported edges are considered; and (4) quantities compared include detailed through-the-thickness distributions of transverse shear and transverse normal stresses. Based on the numerical studies conducted, the predictor-corrector approach appears to be the most effective technique for obtaining accurate transverse stresses, and for thermal loading, none of the two-dimensional models is adequate for calculating transverse normal stresses, even when used in conjunction with three-dimensional equilibrium equations.

Noor, A. K.↗
NASA NTRS1991

Laser interferometer/Preston tube skin-friction comparison in shock/boundary-layer interaction

An evaluation is conducted of the accuracy of the 'Preston tube' surface pitot-pressure skin friction measurement method relative to the already proven laser interferometer skin-friction meter in a swept shock wave/turbulent boundary-layer interaction. The Preston tube was used to estimate the total shear-stress distribution in a fin-generated swept shock-wave/turbulent boundary-layer interaction. The Keener-Hopkins calibration method using the isentropic relation to calculate the Preston-tube Mach number produces the best results.

Kim, K.-S.↗
DOE OSTI2023

Analysis of real-fluid thermodynamic effects on turbulent statistics in transcritical channel flows

Wall-bounded turbulence at high-pressure transcritical conditions with intense density fluctuations are encountered in many technical applications. In this study, we analyze the turbulent energy transport in transcritical channel flows specifically focusing on dissipation rate, turbulent kinetic energy budgets, heat fluxes, and momentum-fluctuation statistics; results from this analysis are used to guide the development of turbulent scaling laws. Furthermore, we find that the dissipation rate of turbulent kinetic energy is dominated by the enstrophy in the logarithmic layer, and the fluctuating viscosity results in the reduced tilting of the vortical structures and the attenuation of streamwise vorticity in the near-wall layer; the fluctuating viscosity attenuates the dissipation rate by reducing the shear strain and the enstrophy production. Local equilibrium of the turbulent kinetic energy exists in the logarithmic layer. We show that the real-fluid thermodynamic effects significantly change the turbulent heat flux correlated with the sweep and the ejection events; the density changes alter the turbulent transport and result in noticeable magnitudes of density-fluctuation-related momentum-fluctuation statistics. From these results, scaling laws for the turbulent length scales and turbulent kinetic energy budgets are proposed, thereby contributing to improvement of the wall models in large-eddy simulations and Reynolds-averaged Navier-Stokes (RANS) simulations.

42 ENGINEERING↗
NASA NTRS2015

Flexible Micropost Arrays for Shear Stress Measurement

Increased fuel costs, heightened environmental protection requirements, and noise abatement continue to place drag reduction at the forefront of aerospace research priorities. Unfortunately, shortfalls still exist in the fundamental understanding of boundary-layer airflow over aerodynamic surfaces, especially regarding drag arising from skin friction. For example, there is insufficient availability of instrumentation to adequately characterize complex flows with strong pressure gradients, heat transfer, wall mass flux, three-dimensionality, separation, shock waves, and transient phenomena. One example is the acoustic liner efficacy on aircraft engine nacelle walls. Active measurement of shear stress in boundary layer airflow would enable a better understanding of how aircraft structure and flight dynamics affect skin friction. Current shear stress measurement techniques suffer from reliability, complexity, and airflow disruption, thereby compromising resultant shear stress data. The state-of-the-art for shear stress sensing uses indirect or direct measurement techniques. Indirect measurements (e.g., hot-wire, heat flux gages, oil interferometry, laser Doppler anemometry, small scale pressure drag surfaces, i.e., fences) require intricate knowledge of the studied flow, restrictive instrument arrangements, large surface areas, flow disruption, or seeding material; with smaller, higher bandwidth probes under development. Direct measurements involve strain displacement of a sensor element and require no prior knowledge of the flow. Unfortunately, conventional "floating" recessed components for direct measurements are mm to cm in size. Whispering gallery mode devices and Fiber Bragg Gratings are examples of recent additions to this type of sensor with much smaller (m) sensor components. Direct detection techniques are often single point measurements and difficult to calibrate and implement in wind tunnel experiments. In addition, the wiring, packaging, and installation of delicate micro-electromechanical devices impede the use of most direct shear sensors. Similarly, the cavity required for sensing element displacement is sensitive to particulate obstruction. This work was focused on developing a shear stress sensor for use in subsonic wind tunnel test facilities applicable to an array of test configurations. The non-displacement shear sensors described here have minimal packaging requirements resulting in minimal or no disturbance of boundary layer flow. Compared to previous concepts, device installation could be simple with reduced cost and down-time. The novelty lies in the creation of low profile (nanoscale to 100 μm) micropost arrays that stay within the viscous sub-layer of the airflow. Aerodynamic forces, which are related to the surface shear stress, cause post deflection and optical property changes. Ultimately, a reliable, accurate shear stress sensor that does not disrupt the airflow has the potential to provide high value data for flow physics researchers, aerodynamicists, and aircraft manufacturers leading to greater flight efficiency arising from more in-depth knowledge on how aircraft design impacts near surface properties.

Wohl, Christopher J.↗
NASA NTRS1994

Physical and Tribological Characteristics of Ion-Implanted Diamond Films

Unidirectional sliding friction experiments were conducted with a natural, polished diamond pin in contact with both as-deposited and carbon-ion-implanted diamond films in ultrahigh vacuum. Diamond films were deposited on silicon, silicon carbide, and silicon nitride by microwave-plasma-assisted chemical vapor deposition. The as-deposited diamond films were impacted with carbon ions at an accelerating energy of 60 keV and a current density of 50 micron A/cm(exp 2) for approximately 6 min, resulting in a dose of 1.2 x 10(exp 17) carbon ions/cm(exp 2). The results indicate that the carbon ion implantation produced a thin surface layer of amorphous, nondiamond carbon. The nondiamond carbon greatly decreased both friction and wear of the diamond films. The coefficients of friction for the carbon-ion-implanted, fine-grain diamond films were less than 0.1, factors of 20 to 30 lower than those for the as-deposited, fine-grain diamond films. The coefficients of friction for the carbon-ion-implanted, coarse-grain diamond films were approximately 0.35, a factor of five lower than those for the as-deposited, coarse-grain diamond films. The wear rates for the carbon-ion-implanted, diamond films were on the order of 10(exp -6) mm(exp 3)/Nm, factors of 30 to 80 lower than that for the as-deposited diamond films, regardless of grain size. The friction of the carbon-ion-implanted diamond films was greatly reduced because the amorphous, nondiamond carbon, which had a low shear strength, was restricted to the surface layers (less than 0.1 micron thick) and because the underlying diamond materials retained their high hardness. In conclusion, the carbon-ion-implanted, fine-grain diamond films can be used effectively as wear resistant, self-lubricating coatings for ceramics, such as silicon nitride and silicon carbide, in ultrahigh vacuum.

Miyoshi, K.↗
NASA NTRS1981

Experimental data and model for the turbulent boundary layer on a convex, curved surface

Experiments were performed to determine how boundary layer turbulence is affected by strong convex curvature. The data gathered on the behavior of the Reynolds stress suggested the formulation of a simple turbulence model. Data were taken on two separate facilities. Both rigs had flow from a flat surface, over a convex surface with 90 deg of turning and then onto a flat recovery surface. The geometry was adjusted so that, for both rigs, the pressure gradient along the test surface was zero. Two experiments were performed at delta/R approximately 0.10, and one at weaker curvature with delta/R approximately 0.05. Results show that after a sudden introduction of curvature the shear stress in the outer part of the boundary layer is sharply diminished and is even slightly negative near the edge. The wall shear also drops off quickly downstream. When the surface suddenly becomes flat again, the wall shear and shear stress profiles recover very slowly towards flat wall conditions. A simple turbulence model, which was based on the theory that the Prandtl mixing length in the outer layer should scale on the velocity gradient layer, was shown to account for the slow recovery.

Gillis, J. C.↗
NASA NTRS1979

Evaluation of the time dependent surface shear stress in turbulent flows

The time dependent surface shear stress has been evaluated using surface heat transfer measurements. For fully developed turbulent pipe and open channel water flows, and incompressible and compressible turbulent boundary layer air flows the measurements indicate the absolute magnitude of the surface shear stress fluctuations will be greater than two times the mean values. The root-mean-square shear stress fluctuations were of the order of 0.2 to 0.4 times the mean surface shear values. Due to these large surface shear stress fluctuations and the nonlinear relation between heat transfer and shear stress, a special technique has been developed to evaluate the measurements. It was found that the non-linear averaging errors for a hot film-surface shear stress gauge in a fully developed pipe flow was of the order of 10 percent at low velocities. A hot wire-surface shear stress gauge was employed for measurements of turbulent boundary layers in air.

Sandborn, V. A.↗
NASA NTRS1984

A new turbulence closure model for boundary layer flows with strong adverse pressure gradients and separation

A new turbulence closure model designed specifically to treat two-dimensional, turbulent boundary layers with strong adverse pressure gradients and attendant separation, is presented. The influence of history effects are modeled by using an ordinary differential equation (ODE) derived from the turbulence kinetic-energy equation, to describe the streamwise development of the maximum Reynolds shear stress in conjunction with an assumed eddy-viscosity distribution which has as its velocity scale the maximum Reynolds shear stress. In the outer part of the boundary layer, the eddy viscosity is treated as a free parameter which is adjusted in order to satisfy the ODE for the maximum shear stress. Because of this, the model s not simply an eddy-viscosity model, but contains features of a Reynolds-stress model. Comparisons with experiments are presented which clearly show the proposed model to be superior to the Cebeci-Smith model in treating strongly retarded and separated flows. In contrast to two-equation, eddy-viscosity models, it requires only slightly more computational effort than simple models like the Cebeci-Smith model.

Johnson, D. A.↗
NASA NTRS1994

Orbital velocities induced by surface waves

During the third intensive observational period of the Surface Wave Dynamics Experiment (SWADE), an aircraft-based experiment was conducted on 5 March 1991 by deploying slow-fall airborne expendable current profilers (AXCPs) and airborne expendable bathythermographs (AXBTs) during a scanning radar altimeter (SRA) flight on the NASA NP-3A research aircraft. As the Gulf Stream (GS) moved into the SWADE domain in late February, maximum upper-layer currents of 1.98 m/s were observed in the core of the baroclinic jet where the vertical current shears were O(10(exp -2)/s). The SRA concurrently measured the sea surface topography, which was transformed into two-dimensional directional wave spectra at 5-6-km intervals along the flight tracks. The wave spectra indicated a local wave field with wavelengths of 40-60 m propagating southward between 120 deg and 180 deg, and a northward-moving swell field from 300 deg to 70 deg associated with significant wave heights of 2-4 m. As the AXCP descended through the upper ocean, the profiler sensed orbital velocity amplitudes of 0.2-0.5 m/s due to low-frequency surface waves. These orbital velocities were isolated by fitting the observed current profiles to the three-layer model based on a monochromatic surface wave, including the steady and current shear terms within each layer. The depth-integrated differences between the observed and modeled velocity profiles were typically less than 3 cm/s. For 17 of the 21 AXCP drop sites, the rms orbital velocity amplitudes, estimated by integrating the wave spectra over direction and frequency, were correlated at a level of 0.61 with those derived from the current profiles. The direction of wave propagation inferred from the AXCP-derived orbital velocities was in the same direction observed by the SRA. These mean wave directions were highly correlated (0.87) and differed only by about 5 deg.

Shay, Lynn K.↗
DOE OSTI2022

Dynamical criticality of spin-shear coupling in van der Waals antiferromagnets

Abstract The interplay between a multitude of electronic, spin, and lattice degrees of freedom underlies the complex phase diagrams of quantum materials. Layer stacking in van der Waals (vdW) heterostructures is responsible for exotic electronic and magnetic properties, which inspires stacking control of two-dimensional magnetism. Beyond the interplay between stacking order and interlayer magnetism, we discover a spin-shear coupling mechanism in which a subtle shear of the atomic layers can have a profound effect on the intralayer magnetic order in a family of vdW antiferromagnets. Using time-resolved X-ray diffraction and optical linear dichroism measurements, interlayer shear is identified as the primary structural degree of freedom that couples with magnetic order. The recovery times of both shear and magnetic order upon optical excitation diverge at the magnetic ordering temperature with the same critical exponent. The time-dependent Ginzburg-Landau theory shows that this concurrent critical slowing down arises from a linear coupling of the interlayer shear to the magnetic order, which is dictated by the broken mirror symmetry intrinsic to the monoclinic stacking. Our results highlight the importance of interlayer shear in ultrafast control of magnetic order via spin-mechanical coupling.

36 MATERIALS SCIENCE↗
NASA NTRS1995

Magnetic reconnection in the presence of sheared flow and density asymmetry: Applications to the Earth's magnetopause

Classical models of magnetic reconnection consist of a small diffusion region bounded by two symmetric slow shocks, across which the plasma is accelerated. Asymmetries often present in space plasmas are sheared plasma flow and dissimilar plasma densities on the two sides of current sheets. In this paper, we investigate magnetic reconnection in the presence of a shear flow and an asymmetric density across the current sheet using two-dimensional magnetohydrodynamic (MHD) simulations. The results demonstrate that magnetic reconnection can occur only for a plasma flow velocity (in the frame of the X line) which is below the Alfven speed in each inflow region. This limits the velocity of the X line to a certain range for a given flow shear and provides an upper limit to the total velocity shear at which reconnection ceases to operate. Depending on the direction of the flow in the adjacent inflow region, the effects from the sheared flow and from the density asymmetry will compete with or enhance each other in respect to the magnitude and location of the currents which bound the outflow regions. The results are applied to the dayside and flank regions of the magnetosphere. For the dayside region where the magnetosheath flow is slow, the magnetic field transition region is thin and the accelerated flow is earthward of the sharp current layer (magnetopause). At the flanks tailward of the X line, shear flow and density asymmetry effects compete making the magnetic field transition layer broad with the high-speed flow contained within the transition region which explains corresponding observations. At the flanks sunward of the X line, shear flow and density asymmetry effects enhance each other and lead to a strong current sheet on the magnetosheath side of the accelerated flow. The total volume affected by magnetic reconnection is much larger than the steady state region. A large bulge region precedes the steady state region. Qualitatively, the bulge and the steady state region have similar signatures and both can explain observations. We provide criteria in order to distinguish between the bulge and the steady state region in observations.

La Belle-Hamer, A. L.↗
DOE OSTI2023

Additively manufactured polymer composites for heat exchanger applications: evaluation of critical thermophysical properties

Polymeric heat exchangers (PHXs) have been used in applications involving weight restrictions, chemical compatibility, and fouling issues. Additive manufacturing (AM) or 3D printing provide new solutions to previously inaccessible combinations of properties and geometries. There are some advancements in the PHXs by AM; however, the process and the properties of materials still need further investigation to improve the overall performance. In this study, additively manufactured polyethylene terephthalate glycol (PETG) composites reinforced with graphite and pitch-based carbon fibers were evaluated for their potential application as PHXs. The thermal conductivity, volumetric heat capacity, coefficient of thermal expansion, creep behavior, and long-term performance were studied in detail. Our results reveal that the composites have an anisotropic thermal conductivity. The thermal conductivity along the printing direction is higher than the layer building direction due to the shear-induced alignment of the fillers. The printed composites achieve good thermal stability with 80% lower CTE at room temperature than neat PETG. Creep tests suggest the creep and creep recovery were highly temperature-dependent, and the deformation can be recovered when the temperature is below glass transition. These results suggest additive manufactured composites be potentially used for heat exchanger applications at low temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Two phase transitions driven by surface electron doping in WTe 2

WTe 2 is a multifunctional quantum material exhibiting numerous emergent phases in which tuning of the carrier density plays an important role. In this work, we demonstrate two nonmonotonic changes in the electronic structure of WTe 2 upon in situ electron doping. The first phase transition is interpreted in terms of a shear displacement of the top WTe 2 layer, which realizes a local crystal structure not normally found in bulk WTe 2 . The second phase transition is associated with stronger interactions between the dopant atoms and the host, both through hybridization and electric field. These results demonstrate that electron doping can drive structural and electronics changes in bulk WTe 2 with implications for realizing nontrivial band-structure changes in heterointerfaces and devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Elasticity of davemaoite as a primary contributor to lower-mantle heterogeneities

Geophysical detection of subducted mid–ocean ridge basalt (MORB) in the lower mantle is hindered by uncertainties in the elasticity of Fe,Al,Mg,Ti–bearing davemaoite, a key MORB component. Using Brillouin spectroscopy and x-ray diffraction, we determined the elasticity of a Ca 0.906(1) Fe 2+ 0.027(1) Fe 3+ 0.042(1) Mg 0.033(1) Al 0.072(1) Ti 0.020(1) Si 0.912(1) O 3 davemaoite up to 113 gigapascals and 2294 K. Here, we found that it exhibited a shear wave velocity 10 to 20% slower than end-member davemaoite, making it the slowest phase among major lower-mantle minerals. Our models show that MORB, containing 20 to 25 volume percent davemaoite, potentially contributes to large low-shear-velocity provinces (LLSVPs), whereas a cumulate layer enriched in davemaoite crystallized from basal magma ocean may comprise ultralow-velocity zones (ULVZs). Davemaoite’s ability to host incompatible and heat-producing elements possibly links LLSVPs and ULVZs to mantle plume initiation and geochemical signatures of ocean island basalts.

Zhou, Wen-Yi [Texas A & M Univ., College Station, ↗
NASA NTRS1974

Impact of combustion products from Space Shuttle launches on ambient air quality

The present work describes some multilayer diffusion models and a computer program for these models developed to predict the impact of ground clouds formed during Space Shuttle launches on ambient air quality. The diffusion models are based on the Gaussian plume equation for an instantaneous volume source. Cloud growth is estimated on the basis of measurable meteorological parameters: standard deviation of the wind azimuth angle, standard deviation of wind elevation angle, vertical wind-speed shear, vertical wind-direction shear, and depth of the surface mixing layer. Calculations using these models indicate that Space Shuttle launches under a variety of meteorological regimes at Kennedy Space Center and Vandenberg AFB are unlikely to endanger the exposure standards for HCl; similar results have been obtained for CO and Al2O3. However, the possibility that precipitation scavenging of the ground cloud might result in an acidic rain that could damage vegetation has not been investigated.

Dumbauld, R. K.↗