Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Particle Size Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92

Size-Resolved Particle Number and Volume Emission Factors for On-Road Gasoline and Diesel Motor Vehicles

Average particle number concentrations and size distributions from {approx}61,000 light-duty (LD) vehicles and {approx}2500 medium-duty (MD) and heavy-duty (HD) trucks were measured during the summer of 2006 in a San Francisco Bay area traffic tunnel. One of the traffic bores contained only LD vehicles, and the other contained mixed traffic, allowing pollutants to be apportioned between LD vehicles and diesel trucks. Particle number emission factors (particle diameter D{sub p} > 3 nm) were found to be (3.9 {+-} 1.4) x 10{sup 14} and (3.3 {+-} 1.3) x 10{sup 15} kg{sup -1} fuel burned for LD vehicles and diesel trucks, respectively. Size distribution measurements showed that diesel trucks emitted at least an order of magnitude more particles for all measured sizes (10 < D{sub p} < 290 nm) per unit mass of fuel burned. The relative importance of LD vehicles as a source of particles increased as D{sub p} decreased. Comparing the results from this study to previous measurements at the same site showed that particle number emission factors have decreased for both LD vehicles and diesel trucks since 1997. Integrating size distributions with a volume weighting showed that diesel trucks emitted 28 {+-} 11 times more particles by volume than LD vehicles, consistent with the diesel/gasoline emission factor ratio for PM{sub 2.5} mass measured using gravimetric analysis of Teflon filters, reported in a companion paper.

54 ENVIRONMENTAL SCIENCES↗

Optical property investigations of polystyrene capped Ca{sub 2}P{sub 2}O{sub 7}:Dy{sup 3+} persistent phosphor

Highlights: • Synthesis of polymer capped pyrophosphate phosphors by citrate gel method. • Radiative lifetime is calculated from parameters of Judd-Ofelt theory and ICP-AES. • Reaction mechanism is discussed leading to high photoluminescence efficiency. • PL emission spectrum reveals broad band emission suitable for solid state lighting. - Abstract: By virtue of enhanced photosensivity, good optical response and better thermal stability, organic–inorganic hybrid materials are contemplated as one of the alternatives for designing advanced optoelectronic devices and innovative photonic applications. A novel inorganic organic hybrid Ca{sub 2}P{sub 2}O{sub 7}:Dy{sup 3+} phosphor has been fabricated by Pechini method. The optical property of synthesized phosphor is successfully altered by the in corporation of polystyrene sulfonic acid as capping agent in the colloidal solution. The phase purity and the average particle size of the prepared phosphor were calculated from X-ray diffraction (XRD) employing Debye Scherrer method. The morphological and chemical investigations were carried out through scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) analysis. The radiative transitions are explained on the basis of Judd-Ofelt theory and on the basis of derived parameters, the radiative lifetime of persistent hybrid Ca{sub 2}P{sub 2}O{sub 7}:Dy{sup 3+} phosphor is calculated as 5.33 ms. This paper explores the mechanism leading to high photoluminescence efficiency using organic capping additives. The photoluminescence (PL) graphs reveal broad band emission at 482 nm (blue) and 573 nm (yellow) corresponding to {sup 4}F{sub 9/2}-{sup 6}H{sub 15/2} and {sup 4}F{sub 9/2}-{sup 6}H{sub 13/2} transitions of Dy{sup 3+}, respectively. The Commission International De I-Eclairage (CIE) chromaticity co-ordinates were calculated from emission spectra and the values (x, y) were approaching to standard value of white emission. The synthesized pyrophosphate phosphors can thereby account in multiple potential applications including white light emitting diodes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Photocatalytic activity of SnO{sub 2} nanoparticles in methylene blue degradation

Highlights: • Nanosized SnO{sub 2} photocatalysts were prepared with a precipitation method. • SnO{sub 2} nanoparticles displayed high photocatalytic activities for the MB degradation. • OH radicals are the main active species in photocatalysis on the SnO{sub 2} nanoparticles. - Abstract: Nanosized SnO{sub 2} photocatalysts were prepared with a precipitation method and were characterized by performing transmission electron microscopy (TEM), powder X-ray diffraction (XRD), and X-ray absorption spectroscopy (XAS). The powder XRD results revealed that the SnO{sub 2} nanoparticles have a typical tetragonal rutile (cassiterite) structure and the average crystallite size was found to be approximately 4.5 nm by using the Debye–Scherrer equation. The prepared SnO{sub 2} nanoparticles consist of agglomerated particles with a mean diameter of around 4–5 nm according to the analysis of TEM images. The XAS data confirmed that the prepared samples have cassiterite structures with tin oxidation state of +4. The prepared SnO{sub 2} nanoparticles were found to exhibit approximately 3.8 times higher activity than bulk SnO{sub 2} in the photodegradation of methylene blue. On the basis of a trapping experiment, we developed a possible mechanism for the photodegradation on SnO{sub 2} nanoparticles.

36 MATERIALS SCIENCE↗

Structural and optical characterization of Cr{sub 2}O{sub 3} nanostructures: Evaluation of its dielectric properties

The structural, optical and dielectric properties of as-grown Cr{sub 2}O{sub 3} nanostructures are demonstrated in this paper. Powder X-ray diffractometry analysis confirmed the rhombohedral structure of the material with lattice parameter, a = b = 4.953 Å; c = 13.578 Å, and average crystallize size (62.40 ± 21.3) nm. FE-SEM image illustrated the mixture of different shapes (disk, particle and rod) of as-grown nanostructures whereas; EDS spectrum confirmed the elemental purity of the material. FTIR spectroscopy, revealed the characteristic peaks of Cr–O bond stretching vibrations. Energy band gap (3.2 eV) of the nanostructures has been determined using the results of UV-VIS-NIR spectrophotometer. The dielectric properties of the material were checked in the wide frequency region (100Hz-30 MHz). In the low frequency region, the matrix of the dielectric behaves like source as well as sink of electrical energy within the relaxation time. Low value of dielectric loss exhibits that the materials posses good optical quality with lesser defects. The ac conductivity of the material in the high frequency region was found according to frequency power law. The physical-mechanism and the theoretical-interpretation of dielectric-properties of Cr{sub 2}O{sub 3} nanostructures attest the potential candidature of the material as an efficient dielectric medium.

36 MATERIALS SCIENCE↗

Carbon distribution in bainitic steel subjected to deformation

Analysis of the formation and evolution of carbide phase in medium carbon steel with a bainitic structure during compressive deformation was performed by means of transmission electron diffraction microscopy. Qualitative transformations in carbide phase medium size particles, their density and volume concentration depended on the degree of deformation.

36 MATERIALS SCIENCE↗

Neutronic Evaluation of a Liquid Salt–Cooled Reactor Assembly

This study presents a thorough parametric neutronic analysis of a plate-based tristructual isotropic (TRISO) fuel particle bearing liquid salt–cooled reactor assembly. The analyses presented investigated the effects of altering fuel enrichment, packing fraction, plate region thicknesses, assembly structure thicknesses, assembly size, numbers of plates per assembly, use of burnable poison materials, replacement of assembly and plate carbon material with silicon carbide, and use of uranium nitride fuel kernels. The effects or trends observed included reactivity behavior, discharge burnup, cycle length, and other key design parameters such as moderator temperature coefficients, coolant density coefficients, control blade worth, and impacts upon power peaking (i.e., power and flux distributions).

Nuclear Science & Technology↗

LoCuSS: CALIBRATING MASS-OBSERVABLE SCALING RELATIONS FOR CLUSTER COSMOLOGY WITH SUBARU WEAK-LENSING OBSERVATIONS

We present a joint weak-lensing/X-ray study of galaxy cluster mass-observable scaling relations motivated by the critical importance of accurate calibration of mass proxies for future X-ray missions, including eROSITA. We use a sample of 12 clusters at z {approx_equal} 0.2 that we have observed with Subaru and XMM-Newton to construct relationships between the weak-lensing mass (M) and three X-ray observables, gas temperature (T), gas mass (M{sub gas}), and quasi-integrated gas pressure (Y{sub X}), at overdensities of {Delta} = 2500, 1000, and 500 with respect to the critical density. We find that M{sub gas} at {Delta} {<=} 1000 appears to be the most promising mass proxy of the three because it has the lowest intrinsic scatter in mass at a fixed observable, {sigma}{sub ln{sub M}} {approx_equal} 0.1, independent of the cluster dynamical state. The scatter in mass at fixed T and Y{sub X} is a factor of {approx}2-3 larger than at fixed M{sub gas}, which are indicative of the structural segregation that we find in the M-T and M-Y{sub X} relationships. Undisturbed clusters are found to be {approx}40% and {approx}20% more massive than disturbed clusters at fixed T and Y{sub X}, respectively, at {approx}2{sigma} significance. In particular, A 1914-a well-known merging cluster-significantly increases the scatter and lowers the normalization of the relation for disturbed clusters. We also investigated the covariance between the intrinsic scatter in M-M{sub gas} and M-T relations, finding that they are positively correlated. This contradicts the adaptive mesh refinement simulations that motivated the idea that Y{sub X} may be a low-scatter mass proxy, and agrees with more recent smoothed particle hydrodynamic simulations based on the Millennium Simulation. We also propose a method to identify a robust mass proxy based on principal component analysis. The statistical precision of our results is limited by the small sample size and the presence of the extreme merging cluster in our sample. We therefore look forward to studying a larger, more complete sample in the future.

79 ASTRONOMY AND ASTROPHYSICS↗

Effect of Ascorbic Acid Additions on the Mechanism Underlying the Growth of Nanostructured PbSe Films via Hydrochemical Deposition

The effect of ascorbic acid additions on the growth mechanism of thin PbSe films produced by hydrochemical deposition has been studied by atomic force microscopy (AFM). A fractal analysis of AFM images of the lead selenide films has shown that their formation follows the “cluster–particle” aggregation mechanism. The fractal dimension assessed by the box-counting method is 2.26 at an average grain size of ~150 nm. From the transmission spectra of the films grown at deposition times from 20 to 120 min, we have evaluated their optical band gap, which has been shown to decrease from 0.595 to 0.53 eV with increasing deposition time. These values are attributable to the manifestation of quantum size effects in the grown PbSe films.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Integrated Waste Treatment Unit (IWTU) Input Coal Analyses and Off-Gass Filter (OGF) Content Analyses

A full engineering scale Fluidized Bed Steam Reformer (FBSR) system is being used at the Idaho Nuclear Technology and Engineering Center (INTEC) to stabilize acidic Low Activity Waste (LAW) known as Sodium Bearing Waste (SBW). The INTEC facility, known as the Integrated Waste Treatment Unit (IWTU), underwent an Operational Readiness Review (ORR) and a Technology Readiness Assessment (TRA) in March 2014. The IWTU began non-radioactive simulant processing in late 2014 and by January, 2015 ; the IWTU had processed 62,000 gallons of simulant. The facility is currently in a planned outage for inspection of the equipment and will resume processing simulated waste feed before commencing to process 900,000 gallons of radioactive SBW. The SBW acidic waste will be made into a granular FBSR product (carbonate based) for disposal in the Waste Isolation Pilot Plant (WIPP). In the FBSR process calcined coal is used to create a CO2 fugacity to force the waste species to convert to carbonate species. The quality of the coal, which is a feed input, is important because the reactivity, moisture, and volatiles (C,H,N,O, and S) in the coal impact the reactions and control of the mineralizing process in the primary steam reforming vessel, the Denitration and Mineralizing Reformer (DMR). Too much moisture in the coal can require that additional coal be used. However since moisture in the coal is only a small fraction of the moisture from the fluidizing steam this can be self-correcting. If the coal reactivity or heating value is too low then the coal feed-rate needs to be adjusted to achieve the desired heat generation. Too little coal and autothermal heat generation in the DMR cannot be sustained and/or the carbon dioxide fugacity will be too low to create the desired carbonate mineral species. Too much coal and excess S and hydroxide species can form. Excess sulfur from coal that (1) is too rich in sulfur or (2) from overfeeding coal can promote wall scale and contribute to corrosion in process piping and materials, in excessive off-gas absorbent loading, and in undesired process emissions. The ash content of the coal is important as the ash adds to the DMR and other vessel products which affect the final waste product mass and composition. The amount and composition of the ash also affects the reaction kinetics. Thus ash content and composition contributes to the mass balance. In addition, sodium, potassium, calcium, sulfur, and maybe silica and alumina in the ash may contribute to wall-scale formation. Sodium, potassium, and alumina in the ash will be overwhelmed by the sodium, potassium, and alumina from the feed but the impact from the other ash components needs to be quantified. A maximum coal particle size is specified so the feed system does not plug and a minimum particle size is specified to prevent excess elutriation from the DMR to the Process Gas Filter (PGF). A vendor specification was used to procure the calcined coal for IWTU processing. While the vendor supplied a composite analysis for the 22 tons of coal (Appendix A), this study compares independent analyses of the coal performed at the Savannah River National Laboratory (SRNL) and at the National Energy Technology Laboratory (NETL). Three supersacks a were sampled at three different heights within the sack in order to determine within bag variability and between bag variability of the coal. These analyses were also compared to the vendor’s composite analyses and to the coal specification. These analyses were also compared to historic data on Bestac coal analyses that had been performed at Hazen Research Inc. (HRI) between 2004-2011.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Flyby- and rendezvous-type comet missions from the standpoint of large-particle dust experiments

The measurement by cometary flyby and rendezvous missions of the dust particles emitted from a cometary nucleus and believed to be the major source of the interplanetary dust is considered. The impact rate per unit area of particles in a given size range on a spacecraft dust sensor is calculated in terms of the distance between comet and probe and the particle emission rate and velocity. It is concluded that large-particle (greater than 100-micron) dust analysis experiments cannot be conducted on flyby missions to short-period comets since the required miss distance is orders of magnitude smaller than the targeting error, while for a rendezvous mission much greater miss distances are possible due to the longer period of cometary contact. The problem of designing dust sensors to operate at the subkilometer per second intercept velocities of a rendezvous mission is also noted.

Sekanina, Z.↗

Improved consolidation of silicon carbide

Alpha silicon carbide powder was consolidated by both dry and wet methods. Dry pressing in a double acting steel die yielded sintered test bars with an average flexural strength of 235.6 MPa with a critical flaw size of approximately 100 micro m. An aqueous slurry pressing technique produced sintered test bars with an average flexural strength of 440.8 MPa with a critical flaw size of approximately 25 micro m. Image analysis revealed a reduction in both pore area and pore size distribution in the slurry pressed sintered test bars. The improvements in the slurry pressed material properties are discussed in terms of reduced agglomeration and improved particle packing during consolidation.

Freedman, M. R.↗

Improved consolidation of silicon carbide

Alpha silicon carbide powder was consolidated by both dry and wet methods. Dry pressing in a double acting steel die yielded sintered test bars with an average flexural strength of 235.6 MPa with a critical flaw size of approximately 100 micro m. An aqueous slurry pressing technique produced sintered test bars with an average flexural strength of 440.8 MPa with a critical flaw size of approximately 25 micro m. Image analysis revealed a reduction in both pore area and pore size distribution in the slurry pressed sintered test bars. The improvements in the slurry pressed material properties are discussed in terms of reduced agglomeration and improved particle packing during consolidation.

Freedman, M. R.↗

Micron-sized particle impacts detected near Uranus by the Voyager 2 plasma wave instrument

The characteristics and distribution of the small particles detected by the plasma-wave and radio-astronomy instruments during the Voyager 2 encounter with Uranus in January 1986 are examined. The nature of the observational data and the analysis techniques employed are discussed, and the results are presented in graphs. Particles of rms mass about 2.6 ng and radii of a few microns were found in an impact region of thickness 3840 km, with a maximum number density of 1600/cu m about 280 km from the equatorial plane, shortly after Voyager 2 crossed the plane of the Uranian rings. The possible origin of the particles in the rings or in small satellites outside the rings is considered.

Gurnett, D. A.↗

Uranian ring photometry - Results from Voyager 2

The rings of Uranus are characterized on the basis of an analysis of seven images obtained with a clear filter by Voyager 2 during its encounter with Uranus in January 1986. The data are presented graphically and compared with the predictions of theoretical models with different particle size distributions. Parameters determined include average particle Bond albedo 0.014 + or - 0.004, fractional area of the main rings in dust-size particles 0.002 or less, and average dust-particle size 1.0 + or - 0.3 microns for a Hansen-Hovenier (1974) distribution and a power-law distribution of spherical particles with spectral index 2.5 + or - 0.5.

Ockert, Maureen E.↗

Microgravity bubble migration in rotating flows

The NASA KC-135 microgravity-environment aircraft was used to gather experimental data on the migration of bubbles in rotating liquid fields under reduced gravity conditions. The data thus obtained were compared to those of an analysis for the prediction of fluid particle trajectories in the presence of both gravitational and rotational fields at the limit of quasi-steady creeping flow. Reasonable agreement with experimental results was achieved, despite the large size of the bubbles, their close proximity to a bounding surface over significant portions of their migration time, and their rather nonspherical geometry.

Ruggles, J. S.↗

The status of measurement technologies concerning micrometer and submicrometer space articulate matter capture, recovery, velocity and trajectory

The return of a pristine sample from a comet would lead to greater understanding of cometary structures, as well as offering insights into exobiology. The paper presented at the Discovery Program Workshop outlined a set of measurements for what was identified as a SOCCER-like interplanetary mission. Several experiments comprised the total instrumentation. This paper presents a summary of CCSR with an overview of three of the four major instruments. Details of the major dust dynamics experiment including trajectory are given in this paper. The instrument proposed here offers the opportunity for the return of cometary dust particles gathered in situ. The capture process has been employed aboard the space shuttle with successful results in returning samples to Earth for laboratory analysis. In addition, the sensors will measure the charge, mass, velocity, and size of cometary dust grains during the encounter. This data will help our understanding of dusty plasmas.

Alexander, W. M.↗

Radio Occultation Investigation of the Rings of Saturn and Uranus

The proposed work addresses two main objectives: (1) to pursue the development of the random diffraction screen model for analytical/computational characterization of the extinction and near-forward scattering by ring models that include particle crowding, uniform clustering, and clustering along preferred orientations (anisotropy). The characterization is crucial for proper interpretation of past (Voyager) and future (Cassini) ring, occultation observations in terms of physical ring properties, and is needed to address outstanding puzzles in the interpretation of the Voyager radio occultation data sets; (2) to continue the development of spectral analysis techniques to identify and characterize the power scattered by all features of Saturn's rings that can be resolved in the Voyager radio occultation observations, and to use the results to constrain the maximum particle size and its abundance. Characterization of the variability of surface mass density among the main ring, features and within individual features is important for constraining the ring mass and is relevant to investigations of ring dynamics and origin. We completed the developed of the stochastic geometry (random screen) model for the interaction of electromagnetic waves with of planetary ring models; used the model to relate the oblique optical depth and the angular spectrum of the near forward scattered signal to statistical averages of the stochastic geometry of the randomly blocked area. WE developed analytical results based on the assumption of Poisson statistics for particle positions, and investigated the dependence of the oblique optical depth and angular spectrum on the fractional area blocked, vertical ring profile, and incidence angle when the volume fraction is small. Demonstrated agreement with the classical radiative transfer predictions for oblique incidence. Also developed simulation procedures to generate statistical realizations of random screens corresponding to uniformly packed ring models, and used the results to characterize dependence of the extinction and near-forward scattering on ring thickness, packing fraction, and the ring opening angle.

Marouf, Essam A.↗

Influence of Measurement Uncertainties on Fractional Solubility of Iron in Mineral Aerosols over the Oceans

The atmospheric supply of mineral dust iron (Fe) plays a crucial role in the Earths biogeochemical cycle and is of specific importance as a micronutrient in the marine environment. Observations show several orders of magnitude variability in the fractional solubility of Fe in mineral dust aerosols, making it hard to assess the role of mineral dust for the global ocean biogeochemical Fe cycle. In this study we compare the operational solubility of mineral dust aerosol Fe associated with the flow-through leaching protocol to the results of the global 3-D chemical transport model GEOS-Chem. According to the protocol, aerosol Fe is defined as soluble by first deionized water leaching of mineral dust through a 0.45 m pore size membrane followed by acidification and storage of the leachate over a long period of time prior to analysis. To estimate the uncertainty in soluble Fe results introduced by the flow-through leaching protocol, we prescribe an average 50 (range of 30 to 70) fractional solubility to sub-0.45 m sized mineral dust particles that may inadvertently pass the filter and end up in the acidified (at pH1.7) leachate for a couple of month period. In the model, the fractional solubility of Fe is either explicitly calculated using a complex mineral aerosol Fe dissolution module, or prescribed to be 1 and 4. Calculations show that the fractional solubility of Fe derived through the flow-through leaching is higher compared to the model results. The largest differences (40) are predicted to occur farther away from the dust source regions, over the areas where sub-0.45 m sized mineral dust particles contribute a larger fraction of the total mineral dust mass. This study suggests that different methods used in soluble Fe measurements and inconsistences in the operational definition of filterable Fe in marine environment and soluble Fe in atmospheric aerosols are likely to contribute to the wide range of fractional solubility of aerosol Fe reported in the literature.

Soluble Iron↗