SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This report examines the development and use of coal plastic composite materials for piping applications. Foam materials were developed at bench scale and evaluated according to ASTM specifications. Techno-economic analyses are also reported.
Achieving efficient learning for AI systems was identified as a major challenge in the DOE's recently released, AI for Science , report. The human brain is capable of efficient and low-powered learning. It is likely that implementing brain-like principles will lead to more efficient AI systems. In this LDRD, I aim to contribute to this goal by creating a foundation for implementing and studying a brain phenomenon termed short term plasticity (STP) in spiking artificial neural networks within Sandia. First, data collected by the Allen Institute for Brain Science (AIBS) was analyzed to see if STP could be classified into types using the data collected. Although the data was inadequate at the time, AIBS has updated their database and created models that could be utilized in the future. Second, I began creating a software package to assess the ability of a Boltzmann machine utilizing STP to sample from national security data.
RDX shear banding nucleates without other defects present and is important for both mechanical properties and for mechano-chemical effects. Above ~1.0 km/s particle velocity, the shear band mechanism ceases to occur. It is not replaced by a phase transformation or other plastic event. Shear band initial sites over-nucleate and lower the VM tress drastically. This results in a fully reversible, high pressure mechanism that suppresses the formation of shear bands.
This document demonstrates a calibration of the Preston-Tonks-Wallace (PTW) model of plastic deformation that fairly accurately reproduces the flow stress of half-hard copper across strain rates varying by a factor of more than ten billion. The experiments included are quasistatic compression at low rates, Split Hopkinson Pressure Bar (SHPB) compression at intermediate rates, and arrested Richtmyer-Meshkov instability (RMI) growth at high strain rates. The temperatures vary from liquid nitrogen (77 K) to around 500 K. The largest true strains obtained are approximately 0.5. It would be interesting to compare the results to copper deformation data at higher pressures and higher strains.
This study developed machine learning models using a dataset consisting of 963 entries with 24 variables both numerical and categorical to predict H2 production of plastic waste and biomass gasification. The models were utilized to optimize feedstock and process conditions through genetic algorithm to maximize hydrogen production.
This report summarizes the results of physics-based, crystal plasticity simulations for the long-term stress relaxation behavior of Alloy 709. The purpose of the study was to provide insight into five key questions related to long-term behavior in high temperatures materials which are difficult or impossible to answer experimentally: (1) is there a threshold stress for long-term relaxation? (2) is there strain threshold for relaxation damage, below which significant damage does not accumulate? (3) does damage continue to accumulate as the material relaxes or will damage accumulation plateau under some loading conditions? (4) does stress relaxation loading inevitably lead to failure? and (5) which, if any, engineering models for relaxation damage accumulation reasonably match the simulation results? The report summarizes the numerical simulations used to address these five questions and provides at least partial answers to each question.
This project developed distributed fiber sensors for plastics gasification reactor for clean hydrogen production. These sensors can be directly inserted into gasification reactors to perform real-time, in-situ hydrogen and temperature profile measurements with 5-cm spatial resolution across the entire reactor chamber. Our research team will use this new sensor capability to study how feedstock mixtures, feedstock preparations, and air/steam flows impact feedstock consumption, hydrogen production, and harmful chemical production emissions.
Micro- and nano-plastics (MNPs) pose a significant hazard to both environmental and human health due to their complex interfacial interactions with their surroundings, however there is a lack of techniques available to study the composition of MNPs at their surface. To fill this gap, representative MNPs were coated with matrix that enabled detection via matrix-assisted laser desorption ionization mass spectrometry (MALDI), a technique that has been shown to be surface specific but had not been applied to MNPs previously. Three different coating techniques were tested; evaporation and condensation, drop-casting, and mixed nebulization. Mixed nebulization provided the best balance of results, which was a strong MALDI signal in combination with even coating on the MNP surface from MNPs ≥20 µm. This work provides a new technique for the measurement of MNP surface composition that will help advance the field and enable more thorough studies of the chemical transformations that MNPs undergo in the environment.
As part of the Cyclotron Road program, ReSource Chemical Corp. sought to investigate the conversion of inedible biomass and CO₂ to FDCA. FDCA is a performance monomer widely viewed as a green replacement for the petroleum-derived monomer PTA, which is produced at approximately 60 Mt per year with over 100 Mt of annual GHG emissions. The major polyester made from PTA, called PET, is a >$\$$100B industry with applications in bottling, food packaging, and fibers. The FDCA analogue of PET, called PEF, had superior gas barrier, mechanical, and thermal properties that enable increased shelf life of perishable goods while using less plastic.
The intracerebroventricular (icv) injection of amyloid peptides (Aβ) models Alzheimer’s disease (AD) in mice, as typified by the onset within 15 days of deficits of memory and of hippocampal long-term potentiation (LTP) that are prevented by the blockade of adenosine A2A receptors (A2AR). Since A2AR overfunction is sufficient to trigger memory deficits, we tested if A2AR were upregulated in hippocampal synapses before the onset of memory deficits to support the hypothesis that A2AR overfunction could be a trigger of AD. Six to eight days after Aβ-icv injection, mice displayed no alterations of hippocampal dependent memory; however, they presented an increased excitability of hippocampal synapses, a slight increase in LTP magnitude in Schaffer fiber-CA1 pyramid synapses and an increased density of A2AR in hippocampal synapses. A2AR blockade with SCH58261 (50 nM) normalized excitability and LTP in hippocampal slices from mice sacrificed 7–8 days after Aβ-icv injection. Fifteen days after Aβ-icv injection, mice displayed evident deficits of hippocampal-dependent memory deterioration, with reduced hippocampal CA1 LTP but no hyperexcitability and a sustained increase in synaptic A2AR, which blockade restored LTP magnitude. This shows that the upregulation of synaptic A2AR precedes the onset of deterioration of memory and of hippocampal synaptic plasticity, supporting the hypothesis that the overfunction of synaptic A2AR could be a trigger of memory deterioration in AD.
Genetic incorporation of noncanonical amino acids (ncAAs) has become a powerful tool to enhance existing functions or introduce new ones into proteins through expanded chemistry. This technology relies on the process of nonsense suppression, which is made possible by directing aminoacyl-tRNA synthetases (aaRSs) to attach an ncAA onto a cognate suppressor tRNA. However, different mechanisms govern aaRS specificity toward its natural amino acid (AA) substrate and hinder the engineering of aaRSs for applications beyond the incorporation of a single l-α-AA. Directed evolution of aaRSs therefore faces two interlinked challenges: the removal of the affinity for cognate AA and improvement of ncAA acylation. Here we review aspects of AA recognition that directly influence the feasibility and success of aaRS engineering toward d- and β-AAs incorporation into proteins in vivo. Emerging directed evolution methods are described and evaluated on the basis of aaRS active site plasticity and its inherent constraints.
Additive manufacturing techniques enable a wide range of possibilities for novel radiation detectors spanning simple to highly complex geometries, multi-material composites, and metamaterials that are either impossible or cost prohibitive to produce using conventional methods. The present work identifies a set of promising formulations of photocurable scintillator resins capable of neutron-gamma pulse shape discrimination (PSD) to support the additive manufacturing of fast neutron detectors. The development of these resins utilizes a step-by-step, trial-and-error approach to identify different monomer and cross-linker combinations that meet the requirements for 3D printing followed by a 2-level factorial parameter study to optimize the radiation detection performance, including light yield, PSD, optical clarity, and hardness. The formulations resulted in hard, clear, PSD-capable plastic scintillators that were cured solid within 10 s using 405 nm light. The best-performing scintillator produced a light yield 83% of EJ-276 and a PSD figure of merit equaling 1.28 at 450–550 keVee.
Here, the microstructure of plastic bonded explosives (PBXs) is known to influence behavior during mechanical deformation, but characterizing the microstructure can be challenging. For example, the explosive crystals and binder in formulations such as PBX 9501 do not have sufficient X-ray contrast to obtain three-dimensional data by in situ, absorption contrast imaging. To address this difficulty, we have formulated a series of PBXs using octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) crystals and low-density binder systems. The binders were hydroxyl-terminated polybutadiene (HTPB) or glycidyl azide polymer (GAP) cured with a commercial blend of acrylic monomers/oligomers. The binder density is approximately half of the HMX, allowing for excellent contrast using in situ X-ray computed tomography (CT) imaging. The samples were imaged during unaxial compression using micro-scale CT in an interrupted in situ modality. The rigidity of the binder was observed to significantly influence fracture, crystal-binder delamination, and flow. Additionally, 2D slices from the segmented 3D images were meshed for finite element simulation of the mesoscale response. At low stiffness, the binder and crystal do not delaminate and the crystals move with the material flow; at high stiffness, marked delamination is noted between the crystals and the binder, leading to very different mechanical properties. Initial model results exhibit qualitatively similar delamination.
For decades, plants have been the subject of genetic engineering to synthesize novel, value-added compounds. Polyhydroxyalkanoates (PHAs), a large class of biodegradable biopolymers naturally synthesized in eubacteria, are among the novel products that have been introduced to make use of plant acetyl-CoA metabolic pathways. It was hoped that renewable PHA production would help address environmental issues associated with the accumulation of nondegradable plastic wastes. However, after three decades of effort synthesizing PHAs, and in particular the simplest form polyhydroxybutyrate (PHB), and seeking to improve their production in plants, it has proven very difficult to reach a commercially profitable rate in a normally growing plant. This seems to be due to the growth defects associated with PHA production and accumulation in plant cells. Here, we review major breakthroughs that have been made in plant-based PHA synthesis using traditional genetic engineering approaches and discuss challenges that have been encountered. Then, from the point of view of plant synthetic biology, we provide perspectives on reprograming plant acetyl-CoA pathways for PHA production, with the goal of maximizing PHA yield while minimizing growth inhibition. Specifically, we suggest genetic elements that can be considered in genetic circuit design, approaches for nuclear genome and plastome modification, and the use of multiomics and mathematical modeling in understanding and restructuring plant metabolic pathways.
Here, we describe direct measurements of ozone concentration achievable in small enclosed containers (plastic storage boxes) for use as improvised decontamination systems for small articles such as disposable PPE (N95 masks, nitrile gloves, etc.), clothing, mail and small packages, food, and other miscellaneous articles. The emphasis is on the reliable and sustained generation of ozone gas concentrations of sufficient concentration and duration to create an effective virucidal environment to achieve more than 95% to 99% viral inactivation, based upon the data already published in the peer-review literature on this topic. The suggestion that ozone be used to inactivate virus is certainly not a new idea. Our objective in this report is to make clear that the necessary levels of ozone can be improvised using simple, easy-to-use, inexpensive, and widely available supplies, and that there is every theoretical and experimental reason to believe that this approach is as highly effective in viral inactivation by ozone as are the far more expensive, complex, cumbersome, and less available equivalent ozone (and other) disinfectant systems that have themselves become unavailable during times of pandemic crisis. Using multiple types of readily available commercial ozone generators, concentration in the tested improvised enclosure is tracked over time to assess ozone charging and decay rates, and the ozone quenching effects of items placed in the box. Generator performance is compared against published ozone dosage values for virucidal and antimicrobial activity. Bubbler and box-fan-type ozone generators were found to be effective at achieving and maintaining target concentrations of 10ppm ozone or higher, whereas automotive cigarette lighter and universal serial bus type plug in “air freshener” ozone generators could not achieve the target concentrations in these experiments. Calculations and practical guidelines for assembly and effective use of an ozone box for improvised decontamination are offered. The majority of this report is directed toward the scientific justification and rationale for this approach. The end of the document summarizes the findings and offers simplified designs for the construction and use of ozone boxes as an improvised method of disinfection.
Structures made from a combination of aluminum alloy (AA) and carbon fiber-reinforced plastic (CFRP) are susceptible to galvanic corrosion of the AA in harsh atmospheric conditions, such as might exist for closure panels in automotive applications. It is important to understand the galvanic corrosion behavior of these materials under laboratory conditions as that might allow prediction of performance in real environments. This work tested specially designed AA6×××-CFRP coupons, including AA6111 and AA6022, connected to CFRP made from two different carbon fiber fabrics (twill and random) with the aim of understanding the corrosion behaviors in a laboratory cyclic exposure chamber and during on-road exposure. The extent of corrosion was assessed by galvanic current measurements, optical profilometry, cross-sectional area analysis, and microscopic analysis. Based on the results, it was determined that the corrosion susceptibilities and morphologies observed in CFRP/AA couples tested in an environmental chamber for 12 weeks were in correspondence with those of the coupons subjected to on-road testing for 1 y in Columbus, OH.
This study focuses on the performance of the elastic–viscous–plastic (EVP) dynamical solver within the sea ice model, CICE v6.5.1. The study has been conducted in two steps. First, the standard EVP solver was extracted from CICE for experiments with refactored versions, which are used for performance testing. Second, one refactored version was integrated and tested in the full CICE model to demonstrate that the new algorithms do not significantly impact the physical results. The study reveals two dominant bottlenecks, namely (1) the number of Message Parsing Interface (MPI) and Open Multi-Processing (OpenMP) synchronization points required for halo exchanges during each time step combined with the irregular domain of active sea ice points and (2) the lack of single-instruction, multiple-data (SIMD) code generation. The standard EVP solver has been refactored based on two generic patterns. The first pattern exposes how general finite differences on masked multi-dimensional arrays can be expressed in order to produce significantly better code generation by changing the memory access pattern from random access to direct access. The second pattern takes an alternative approach to handle static grid properties. The measured single-core performance improvement is more than a factor of 5 compared to the standard implementation. The refactored implementation of strong scales on the Intel® Xeon® Scalable Processors series node until the available bandwidth of the node is used. For the Intel® Xeon® CPU Max series, there is sufficient bandwidth to allow the strong scaling to continue for all the cores on the node, resulting in a single-node improvement factor of 35 over the standard implementation. This study also demonstrates improved performance on GPU processors.
Profile coating has been successfully applied to produce elliptical Kirkpatrick-Baez (KB) mirrors using both cylindrical and flat Si substrates. Previously, focusing widths of 70 nm with 15-keV monochromatic and 80 nm with white beam were achieved using a flat Si substrate. Now, precision elliptical KB mirrors with sub-nm figure errors are produced with both Au and Pt coatings on flat substrates. Recent studies of bare Si-, Au-, and Pt-coated KB mirrors under prolonged synchrotron X-ray radiation and low-temperature vacuum annealing will be discussed in terms of film stress relaxation and Si plastic deformation.