Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92

Nanoindentation Studies Of Hard Nanocomposite Ti-B-N Thin Films

Titanium boron nitride (Ti-B-N) films were deposited by reactive magnetron sputtering using single Titanium diboride (TiB{sub 2}) target in different Ar-N{sub 2} gas mixtures. The influence of N{sub 2}:Ar ratio on the microstructure and mechanical properties of the deposited films have been investigated. Atomic force microscopy analysis indicated the grain size decreases with incorporation of nitrogen in the films. Nanoindentation studies have shown the hardness decreases with nitrogen incorporation.

36 MATERIALS SCIENCE↗

Electroplated L1{sub 0} CoPt thick-film permanent magnets

The fabrication and magnetic characterization of 15-μm-thick electroplated L1{sub 0} CoPt hard magnets with good magnetic properties is reported in this paper. Experimental study of the dependence of the magnets' properties on annealing temperature reveals that an intrinsic coercivity H{sub ci} = ∼800 kA/m (10 kOe), squareness >0.8, and energy product of >150 kJ/m{sup 3} are obtained for photolithographically patterned structures (250 μm × 2 mm stripes; 15 μm thickness) electroplated on silicon substrates and annealed in hydrogen forming gas at 700 °C. Scanning electron microscopy is used to inspect the morphology of both the as-deposited and annealed magnetic layers, and X-ray Diffractometer analysis on the magnets annealed at 700 °C confirm a phase transformation to an ordered L1{sub 0} CoPt structure, with a minor phase of hcp Co. These thick films are intended for microsystems/MEMS applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ga lithography in sputtered niobium for superconductive micro and nanowires

This work demonstrates the use of focused ion beam (FIB) implanted Ga as a lithographic mask for plasma etching of Nb films. Using a highly collimated Ga beam of a FIB, Nb is implanted 12 nm deep with a 14 nm thick Ga layer providing etch selectivity better than 15:1 with fluorine based etch chemistry. Implanted square test patterns, both 10 μm by 10 μm and 100 μm by 100 μm, demonstrate that doses above than 7.5 × 10{sup 15 }cm{sup −2} at 30 kV provide adequate mask protection for a 205 nm thick, sputtered Nb film. The resolution of this dry lithographic technique is demonstrated by fabrication of nanowires 75 nm wide by 10 μm long connected to 50 μm wide contact pads. The residual resistance ratio of patterned Nb films was 3. The superconducting transition temperature (T{sub c}) = 7.7 K was measured using a magnetic properties measurement system. This nanoscale, dry lithographic technique was extended to sputtered TiN and Ta here and could be used on other fluorine etched superconductors such as NbN, NbSi, and NbTi.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Multiple-robot drug delivery strategy through coordinated teams of microswimmers

Untethered robotic microswimmers are very promising to significantly improve various types of minimally invasive surgeries by offering high accuracy at extremely small scales. A prime example is drug delivery, for which a large number of microswimmers is required to deliver sufficient dosages to target sites. For this reason, the controllability of groups of microswimmers is essential. In this paper, we demonstrate simultaneous control of multiple geometrically similar but magnetically different microswimmers using a single global rotating magnetic field. By exploiting the differences in their magnetic properties, we triggered different swimming behaviors from the microswimmers by controlling the frequency and the strength of the global field, for example, one swim and the other does not while exposed to the same control input. Our results show that the balance between the applied magnetic torque and the hydrodynamic torque can be exploited for simultaneous control of two microswimmers to swim in opposite directions, with different velocities, and with similar velocities. This work will serve to establish important concepts for future developments of control systems to manipulate multiple magnetically actuated microswimmers and a step towards using swarms of microswimmers as viable workforces for complex operations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Synthesis of cobalt alloy through smelting method and its characterization as prosthesis bone implant

Cobalt-based alloys are widely used as total hip and knee replacements because of their excellent properties, such as corrosion resistance, fatigue strength and biocompatibility. In this work, cobalt alloys with variation of Cr (28.5; 30; 31.5; 33, and 34.5% wt) have been synthesized by smelting method began with the process of compaction, followed by smelting process using Tri Arc Melting Furnace at 200A. Continued by homogenization process at recrystallization temperature (1250° C) for 3 hours to allow the atoms diffuses and transform into γ phase. The next process is rolling process which is accompanied by heating at 1200° C for ± 15 minutes and followed by quenching. This process is repeated until the obtained thickness of ± 1 mm. The evaluated material properties included microstructure, surface morphology, and hardness value. It was shown that microstructure of cobalt alloys with variation of Cr is dominant by γ phase, thus making the entire cobalt alloys have high hardness. It was also shown from the surface morphology of entire cobalt alloys sample indicated the whole process of synthesis that had good solubility were at flat surface area. Hardness value test showed all of cobalt alloys sample had high hardness, just variation of 33% Cr be in the range of ASTMF75, it were 345,24 VHN which is potential to be applied as an implant prosthesis.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Surface plasmon polariton assisted red shift in excitonic emission of semiconductor microflowers

We report on the study of metal nanoparticle-semiconductor hybrid system composed of β-indium sulfide (β-In{sub 2}S{sub 3}) and gold (Au) nanoparticles. β-In{sub 2}S{sub 3} micron sized flower like structures (∼1 μm) and Au nanoparticles (∼10 nm) were synthesized by chemical route. These Au nanoparticles have surface plasmon resonance at ∼ 520 nm. We study the influence of Au surface plasmon polaritons on the radiative properties of the β-In{sub 2}S{sub 3} microflowers. As a result of the coupling between the surface plasmon polaritons and the excitons there is a red shift ∼ 50 nm in emission spectrum of hybrid β-In{sub 2}S{sub 3}-Au system. Such hybrid systems provide scope for a control on the optical properties of semiconductor microstructures, thus rendering them suitable for specific device applications in optoelectronics and photovoltaics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Multirate delivery of multiple therapeutic agents from metal-organic frameworks

The highly porous nature of metal-organic frameworks (MOFs) offers great potential for the delivery of therapeutic agents. Here, we show that highly porous metal-organic frameworks can be used to deliver multiple therapeutic agents—a biologically active gas, an antibiotic drug molecule, and an active metal ion—simultaneously but at different rates. The possibilities offered by delivery of multiple agents with different mechanisms of action and, in particular, variable timescales may allow new therapy approaches. Here, we show that the loaded MOFs are highly active against various strains of bacteria.

36 MATERIALS SCIENCE↗

Fabrication and characterization of photovoltaic devices based on perovskite compounds with TiO{sub 2} nanoparticles

Perovskite-type photovoltaic devices were fabricated by a spin-coating method using a mixture solution. The compact and meso-porous TiO{sub 2} of the solar cells were fabricated from TiO{sub 2} nanoparticles and sol, and the photovoltaic properties and microstructures were characterized. The conversion efficiencies were improved by the combination of TiO{sub 2} nanoparticles and sol. Current density was also improved by increasing numbers of spin-coatings of meso-porous TiO{sub 2}. Thick meso-porous TiO2 layers would assist the construction of perovskite layers and block of the leak current.

36 MATERIALS SCIENCE↗

Low temperature fabrication of perovskite solar cells with TiO{sub 2} nanoparticle layers

TiO{sub 2}/CH{sub 3}NH{sub 3}PbI{sub 3}-based photovoltaic devices were fabricated by a spin-coating method using a mixture solution. TiO{sub 2} require high-temperature processing to achieve suitably high carrier mobility. TiO{sub 2} electron transport layers and TiO{sub 2} scaffold layers for the perovskite were fabricated from TiO{sub 2} nanoparticles with different grain sizes. The photovoltaic properties and microstructures of solar cells were characterized. Nanoparticle sizes of these TiO{sub 2} were 23 nm and 3 nm and the performance of solar cells was improved by combination of two TiO{sub 2} nanoparticles.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Magnetic properties of lithium zinc ferrites synthesized by microwave sintered method

In this paper, a series of polycrystalline ferrite samples were prepared with the composition of Zn{sub 0.1}Li{sub 0.525-x}Ti{sub 0.15}Mg{sub x}Fe{sub 2.225-0.5x}O{sub 4} (LiZn) (x=0, 0.05, 0.10, 0.15 and 0.20) using both microwave sintering (MS) and conventional sintering (CS) technologies, respectively. The sintering time and temperature were 22 hours and 1000°C for the CS process, and 2 hours and 880°C for the MS process. Experiments showed that the MS treated LiZn ferrites exhibited more excellent magnetic properties and denser, more uniform micro-structures comparing with the ones treated by CS method. For the LiZn ferrite (x=0.1) sintered at 880°C using MS, the saturation magnetic induction (Bs) is 242.3 mT, the coercive force (Hc) is 135 A/m, the square ratio (Br/Bs) is 0.87 and the ferromagnetic resonance line-width (Δ H) is 143.2 Oe. These results represented very good properties for an X-band phase shifter material and indicated that the MS method is a potentially important technique for fabricating low temperature co-fired ceramics (LTCC).

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural and magnetic properties of (111) oriented annealed ultrathin Co/Pt multilayers

The effect of annealing on the structural and magnetic properties of Co/Pt multilayers was studied as a function of annealing temperature. The ultrathin layers of Pt and Co were deposited to make [Pt 1nm/Co 1nm]{sub x20} multilayer on Si (100) substrate using MBE technique. The structural, magnetic and electronic properties were recorded using XRD, SQUID and XPS techniques, respectively. M-H loop of as deposited sample shows soft magnetic nature with coercivity value of 350 Oe which increases to 974 Oe in 500°C annealed film. When studied at low temperature (5 K), the coercivity of 592 Oe is obtained in the as deposited sample which increases to 1626 Oe after annealing. In addition, as revealed by X-ray photoelectron spectroscopy, modifications in core level and valance band are observed. The observed changes in magnetic and electronic properties are attributed to structural modifications in correlation with the changes in (111) orientation of the films seen by X-ray diffraction.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Improvement of the titanium implant biological properties by coating with poly (ε-caprolactone)-based hybrid nanocomposites synthesized via sol-gel

When bioactive coatings are applied to medical implants by means of sol-gel dip coating technique, the biological proprieties of the implant surface can be modified to match the properties of the surrounding tissues. In this study organo-inorganic nanocomposites materials were synthesized via sol-gel. They consisted of an inorganic zirconium-based and silica-based matrix, in which a biodegradable polymer (the poly-ε-caprolactone, PCL) was incorporated in different weight percentages. The synthesized materials, in sol phase, were used to dip-coat a substrate of commercially pure titanium grade 4 (CP Ti gr. 4) in order to improve its biological properties. A microstructural analysis of the obtained films was carried out by scanning electron microscopy (SEM) and attenuated total reflectance (ATR) Fourier transform infrared spectroscopy (FT-IR). Biological proprieties of the coated substrates were investigated by means of in vitro tests.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Strong emission of THz radiation from GaAs microstructures on Si

Remarkably strong emission of terahertz radiation from illuminated GaAs microstructures on a Si substrate is reported. The peak-to-peak amplitude of terahertz radiation from the sample is 9 times larger than that of THz radiation from a semi-insulating GaAs wafer. The spectral width of the sample is larger than that of a semi-insulating GaAs wafer; in particular, the spectral amplitude increases at higher frequencies. As a result, the presented GaAs microstructures on a Si substrate can be suitable for practical and efficient THz sources required in various THz applications.

36 MATERIALS SCIENCE↗

Characterization and nondestructive inspection of additively manufactured materials

Additively manufactured (AM) components often exhibit significant discontinuities and indications without a clear understanding of how they might affect the mechanical properties of a part during qualification and service. This uncertainty is unacceptable for the design and manufacturing of most aerospace components. Current research in both mechanical testing and nondestructive evaluation involves developing methods for characterizing and inspecting AM components as the use of such materials continues to rise. Although several AM manufacturing methods have been developed in recent decades, this paper focuses on AM production-ready processes for a direct metal laser sintering (DMLS) powder bed fusion machine and will provide background on Sandia National Laboratories’ research efforts in this area. Tensile bar samples manufactured using the DMLS powder bed fusion method were inspected in this study, and the results of ultrasonic spectroscopy for assessing internal flaws will be presented. A combination of material property evaluation, microstructural characterization, and nondestructive inspection techniques will also be described. Finally, the results obtained from these material evaluation methods assist in determining inspection limits and methods for qualifying AM materials.

36 MATERIALS SCIENCE↗

A data-driven approach to construct a quantitative relationship between microstructural features of fatigue cracks and contact acoustic nonlinearity

This study demonstrates the feasibility of a data-driven approach to construct a quantitative relationship between nonlinear acoustic parameters and microstructural features of contact interfaces. The near-surface nonlinearity is measured using dynamic acousto-elastic testing (DAET) with a surface wave probe, while the microstructural features are extracted from scanning electron microscopy (SEM) images of fatigue cracks. Four aluminum alloy samples, each having a fatigue crack are prepared. Six local nonlinearity parameters are measured at different locations along the crack propagation direction. A total of 40 local measurements are acquired. A principal component analysis (PCA) reveals that all six nonlinearity parameters are correlated and hence can be replaced by one principal component (PC). Fifteen crack micro-geometrical features at each measurement point were extracted from the SEM images. Regression analysis is used to relate the PC of the nonlinearity parameters to the microstructural features at the crack interface. We compare three regression models that take variable selection into account: stepwise multiple linear regression (MLR), stepwise principal component regression (PCR), and least absolute shrinkage and selection operator (LASSO). Despite having different principles, the three predictive models identify two features as the most significant in predicting the interface nonlinearity: the crack aperture (opening) distribution and the distance to the crack tip. The differences between the three models and the physical interpretation of the data-driven predictions are discussed.

36 MATERIALS SCIENCE↗

Micro-strains, local stresses, and coherently diffracting domain size in shock compressed Al(100) single crystals

In situ x-ray diffraction (XRD) measurements and their analysis in Al single crystals shock compressed along the [100]-direction were utilized to examine shock wave induced microstructural heterogeneities. High-resolution XRD line profiles for the 200, 400, and 600 Al peaks were measured in uniaxial strain compression states to either 5.6 or 11.7 GPa and partial stress release to 3.5 or 6.6 GPa, respectively. Broadening of the XRD line profiles was analyzed to determine the magnitude of the longitudinal micro-strain distribution (0.195% and 0.28% full width at half maximum for 3.5 and 6.6 GPa stresses, respectively) and the size of coherently diffracting domains (CDDs) (0.125 and 0.07 μm for 3.5 and 6.6 GPa stresses, respectively). From the longitudinal micro-strain distributions, the distribution of local stress differences (or stress deviators) was obtained in the shocked state. The full width at half maximum of this distribution, a measure of the local stress inhomogeneities, is greater than half of the macroscopic stress difference for both 3.5 and 6.6 GPa peak stresses, suggesting considerable variation in local stress deviators. The CDD sizes determined here are comparable to characteristic length scales for defect-free regions determined from defect density measurements in post-shock recovery experiments. As a result, the present work represents an important step in understanding material microstructure and inhomogeneities in the shock-compressed state.

36 MATERIALS SCIENCE↗

Effect of focused nanosecond laser pulse irradiation on microtribological properties of diamond-like films

We have examined the effect of focused nanosecond laser pulses on the formation and tribological properties of microstructures in the form of a matrix of craters produced in a – C : H : Si : O diamond-like films (DLFs), both undoped and doped with tungsten. The studies are performed by scanning probe microscopy (SPM) using SPM probes of standard design with a tip and probes without a tip (tipless-type probes). A special procedure is developed for assessing the wettability (contact angle) of individual sections of the laser-induced microstructure by the local adhesion force. According to estimates, the material inside the crater becomes softer and more hydrophobic as a result of laser irradiation. This is manifested to the greatest extent in tungsten-doped DLFs, where the crater walls are arranged like terraces formed by ‘nanoflakes’, i.e. grains of the substance. Scanning of microstructures with a tipless probe in the regime of lateral force microscopy demonstrates a decrease in friction in the crater area. (interaction of laser radiation with matter. laser plasma)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗