Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Matrix models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92

Combined bending and thermal fatigue of high-temperature metal-matrix composites - Computational simulation

The nonlinear behavior of a high-temperature metal-matrix composite (HT-MMC) was simulated by using the metal matrix composite analyzer (METCAN) computer code. The simulation started with the fabrication process, proceeded to thermomechanical cyclic loading, and ended with the application of a monotonic load. Classical laminate theory and composite micromechanics and macromechanics are used in METCAN, along with a multifactor interaction model for the constituents behavior. The simulation of the stress-strain behavior from the macromechanical and the micromechanical points of view, as well as the initiation and final failure of the constituents and the plies in the composite, were examined in detail. It was shown that, when the fibers and the matrix were perfectly bonded, the fracture started in the matrix and then propagated with increasing load to the fibers. After the fibers fractured, the composite lost its capacity to carry additional load and fractured.

Gotsis, Pascal K.↗

Acoustic Surveys of a Scaled-Model CESTOL Transport Aircraft in Static and Forward Speed Conditions

An 11% scale-model of a Cruise-Efficient Short Take-off and Landing (CESTOL) scalemodel test was recently completed. The test was conducted in the AEDC National Full-Scale Aerodynamic Complex (NFAC) 40- by 80-Foot Wind Tunnel at NASA Ames Research Center. The model included two over-wing pod-mounted turbine propulsion simulators (TPS). The hybrid blended wing-body used a circulation control wing (CCW) with leadingand trailing-edge blowing. The bulk of the test matrix included three forward velocities (40 kts, 60 kts, and 100kts), angle-of-attack variation between -5 and 25 , and CCW mass flow variation. Seven strut-mounted microphones outboard of the left wing provided source directivity. A phased microphone array was mounted outboard of the right wing for source location. The goal of this paper is to provide a preliminary look at the acoustic data acquired during the Advanced Model for Extreme Lift and Improved Aeroacoustics (AMELIA) test for 0 angle-of-attack and 0 sideslip conditions. Data presented provides a good overview of the test conditions and the signal-to-noise quality of the data. TPS height variation showed a difference of 2 dB to 3 dB due to wing shielding. Variation of slot mass flow showed increases of 12 dB to 26 dB above the airframe noise and the TPS increased the overall levels an additional 5 dB to 10 dB.

Burnside, Nathan↗

Progressive Damage Failure Analysis of a Multi-Stringer Post-Buckled Panel

Validation of a progressive damage finite element analysis model using the CompDam material model was performed on a large multi-stringer panel subjected to compressive loading. The panel had a Teflon insert embedded between the skin panel and stiffener to cause an ultimate failure mode of stiffener separation. The compressive loading of the panel caused the skin between the stiffeners to locally buckle before any damage began to occur. The post-buckled behavior of the panel was the driving mechanism to the onset of damage and the damage growth that led to skin-stiffener separation. An integrated global-local modeling approach was used to validate several aspects the overall behavior of the panel from start to failure. The global region captured the pre-buckled stiffness of the test panel within 10% and the buckling load of the skin panel at the critical location within 2%. The skin’s five half-wave buckled mode shape was accurately predicted by the model. The integrated local model captured the load corresponding to the onset of damage within 5% of the average test data. Comparisons are made for key aspects of the damage morphology, such as a growth pattern that included a significant matrix split in the first ply of the skin and a migration of the delamination from the skin-stiffener interface to the skin’sply1-ply2 interface. The ultimate failure mode was shown to be an unstable growth of delamination damage under the stiffeners which led to a peak load of the analysis that was approximately 5% above the average peak load of the testing. The validated global-local modeling approach used on the multi-stringer post-buckled panel with a Teflon insert used a methodology and lessons learned using smaller specimens applied to a subcomponent that captured several aspects of a modern aircraft design.

Jason Action↗

Dynamics of a spinning space station with a counterweight connected by multiple cables.

A unique and relatively simple approach is presented for obtaining the linearized equations of motion. A conservative system consisting of two rigid bodies connected by any number of massless cables with linear axial stiffness is assumed. The cable forces and torques are expanded in a Taylor series about the equilibrium values of the system coordinates which results in a cable stiffness matrix. The method of obtaining the equilibrium values of the coordinates is discussed and results are presented. The range of validity of the linear model is determined by comparing results with a digital simulation of the nonlinear system.

Nixon, D. D.↗

K-LL Auger transition probabilities for elements with low and intermediate atomic numbers

Radiationless K-LL transition probabilities have been calculated nonrelativistically in j-j coupling and in intermediate coupling, without and with configuration interaction, for elements with atomic numbers from 13 to 47. The system is treated as a coupled two-hole configuration. The single-particle radial wave functions required in the calculation of radial matrix elements, and in the calculation of mixing coefficients in the intermediate-coupling scheme, were obtained from Green's atomic independent-particle model. Comparison with previous theoretical work and with experimental data is made. The effects of intermediate coupling, configuration interaction, and relativity are noted.

Chen, M. H.↗

Effect of molecular anisotropy on the intensity and degree of polarization of light scattered from model atmospheres

Computations of the intensity, flux, degree of polarization, and the positions of neutral points are presented for models of the terrestrial gaseous and hazy atmospheres by incorporating the molecular anisotropy due to air in the Rayleigh scattering optical thickness and phase matrix. Molecular anisotropy causes significant changes in the intensity, flux and the degree of polarization of the scattered light. The positions of neutral points do not change significantly. When the Rayleigh scattering optical thickness is kept constant and the molecular anisotropy factor is included only in the Rayleigh phase matrix, the flux does not change and the intensity and positions of neutron points change by a small amount. The changes in the degree of polarization are still significant.

Bahethi, O. P.↗

Validity of approximate methods in molecular scattering - Thermal HCl-He collisions

Accurate close coupling scattering calculations are presented for thermal energy HCl-He collisions. The interaction potential is obtained from the Gordon-Kim electron gas model, adjusted to have the correct long-range multipole form. A variety of phenomenological cross sections are computed from the close coupling S matrix, and these are compared with results from several commonly employed approximate methods. In particular, it is found that the total integral, total differential, and gas kinetic cross sections are accurately predicted by the central field approximation which retains just the spherical average of the interaction. Integral inelastic cross sections are represented quite accurately by the coupled states approximation of McGuire and Kouri, but only qualitatively by the effective potential method of Rabitz.

Green, S.↗

Creep and rupture of an ODS alloy with high stress rupture ductility

The creep and stress rupture properties of an oxide (Y2O3) dispersion strengthened nickel-base alloy, which also is strengthened by gamma-prime precipitates, was studied at 760 and 1093 C. At both temperatures, the alloy YDNiCrAl exhibits unusually high stress rupture ductility as measured by both elongation and reduction in area. Failure was transgranular, and different modes of failure were observed including crystallographic fracture at intermediate temperatures and tearing or necking almost to a chisel point at higher temperatures. While the rupture ductility was high, the creep strength of the alloy was low relative to conventional gamma prime strengthened superalloys in the intermediate temperature range and to ODS alloys in the higher temperature range. These findings are discussed with respect to the alloy composition; the strengthening oxide phases, which are inhomogeneously dispersed; the grain morphology, which is coarse and elongated and exhibits many included grains; and the second phase inclusion particles occurring at grain boundaries and in the matrix. The creep properties, in particular the high stress dependencies and high creep activation energies measured, are discussed with respect to the resisting stress model of creep in particle strengthened alloys.

Mcalarney, M. E.↗

Developments in the design, analysis, and fabrication of advanced technology transmission elements

Over the last decade, the presently reported proprietary development program for the reduction of helicopter drive system weight and cost and the enhancement of reliability and survivability has produced high speed roller bearings, resin-matrix composite rotor shafts and transmission housings, gear/bearing/shaft system integrations, photoelastic investigation methods for gear tooth strength, and the automatic generation of complex FEM models for gear/shaft systems. After describing the design features and performance capabilities of the hardware developed, attention is given to the prospective benefits to be derived from application of these technologies, with emphasis on the relationship between helicopter drive system performance and cost.

Drago, R. J.↗

A revised version of the transfer matrix method to analyze one-dimensional structures

A new and general method to analyze both free and forced vibration characteristics of one-dimensional structures is discussed in this paper. This scheme links for the first time the classical transfer matrix method with the recently developed integrating matrix technique to integrate systems of differential equations. Two alternative approaches to the problem are presented. The first is based upon the lumped parameter model to account for the inertia properties of the structure. The second releases that constraint allowing a more precise description of the physical system. The free vibration of a straight uniform beam under different support conditions is analyzed to test the accuracy of the two models. Finally some results for the free vibration of a 12th order system representing a curved, rotating beam prove that the present method is conveniently extended to more complicated structural dynamics problems.

Nitzsche, F.↗

Constituent Properties and Interrelationships

The requirements and recommendations of constituent properties and relationships are: (1) goals/requirement statement; (2) better operational definition of toughness; (3) assess limitations of current micromechanics models/procedures; (4) explicity assess currently known resin toughening mechanisms and determine their relative importance to matrix resins; (5) method to define the interphase region in situ; (6) assess thermodynamic compatibility of any new resin with the fiber; and (7) model polymer systems.

Source record↗

Precision pointing of scientific instruments on space station: The LFGGREC perspective

An application of Lyapunov function-gradient-generated robustness-enhancing control (LFGGREC) is explored. The attention is directed to a reduced-complexity representation of the pointing problem presented by the system composed of the Space Infrared Telescope Facility gimbaled to a space station configuration. Uncertainties include disturbance forces applied in the crew compartment area and control moments applied to adjacent scientific payloads (modeled as disturbance moments). Also included are uncertainties in gimbal friction and in the structural component of the system, as reflected in the inertia matrix, the damping matrix, and the stiffness matrix, and the effect of the ignored vibrational dynamics of the structure. The emphasis is on the adaptation of LFGGREC to this particular configuration and on the robustness analysis.

Blackwell, C. C.↗

An improved error assessment for the GEM-T1 gravitational model

Several tests were designed to determine the correct error variances for the GEM-T1 gravitational solution which was derived exclusively from satellite tracking data. The basic method employs both wholly independent and dependent subset data solutions and produces a full field coefficient by coefficient estimate of the model uncertainties. The GEM-T1 errors were further analyzed using a method based upon eigenvalue-eigenvector analysis which calibrates the entire covariance matrix. Dependent satellite and independent altimetric and surface gravity data sets, as well as independent satellite deep resonance information, confirm essentially the same error assessment.

Lerch, F. J.↗

A technique to calibrate polarimetric radar images using only image parameters and trihedral corner reflectors

The technique described uses the radar return from natural targets and at least one trihedral corner reflector to calibrate compressed polarimetric radar data for relative amplitude, relative phase, absolute amplitude, and system crosstalk. The crosstalk method is based on the theoretical result that, for natural targets with azimuthal symmetry, the copolarized and cross-polarized components of the scattering matrix are uncorrelated. This method does not require any external calibration targets to be deployed. Since compressed data are used, it is necessary to model the transmitting and receiving systems as reciprocal. The method is used to estimate the crosstalk parameters of the NASA/JPL aircraft for different types of terrain and for two frequencies. For the C-band systems the crosstalk is less than -20 dB for all ranges in the images. The crosstalk of the L-band system is a function of range, however, and may be as poor as -10 dB in the near range, leading to a noticeable distortion of the polarization signatures.

Van Zyl, Jakob J.↗

Transonic adaptive flutter suppression using approximate unsteady time domain aerodynamics

A digital adaptive controller is applied to the active flutter suppression problem of a wing under time varying flight conditions in subsonic and transonic flow. Linear quadratic controller gain at each time step is obtained using an iterative Riccati solver. The digital adaptive optimal controller is robust with respect to the unknown external loads. Flutter and divergence instabilities are simultaneously suppressed using a trailing-edge control surface and displacement sensing. A new transonic unsteady aerodynamic approximation methodology is developed which enables one to carry out the rapid calculation required for transonic aeroservoelastic applications. This approximation is based on a combination of unsteady subsonic aerodynamics combined with a transonic correction procedure. Aeroservoelastic transient time response is obtained using Roger's approximation, state transition matrices and an iterative time marching algorithm. The aeroservoelastic system in the time domain is modeled using a deterministic ARMA model together with a parameter estimator. Transonic flutter boundaries of a wing structure are computed, in the time domain, using an estimated aeroelastic system matrix and are in good agreement with experimental data for the low transonic Mach number range.

Pak, Chan-Gi↗

A second-order structural identification procedure via state space-based system identification

A theory is presented for transforming the system theory-based realization models into the corresponding physical coordinate-based structural models. The theory has been implemented into a computational procedure and applied to several example problems. The results show that the present transformation theory yields an objective model basis possessing a unique set of structural parameters from an infinite set of equivalent system realization models. For proportionally damped systems, the transformation directly and systematically yields the normal modes and modal damping. When non-proportional damping is present, the relative magnitude and phase of the damped model shapes are separately characterized, and a corrective transformation is then employed to capture the undamped normal modes and non-diagonal modal damping matrix.

Alvin, K. F.↗

A parameter estimation algorithm for spatial sine testing - Theory and evaluation

This paper presents the theory and an evaluation of a spatial sine testing parameter estimation algorithm that uses directly the measured forced mode of vibration and the measured force vector. The parameter estimation algorithm uses an ARMA model and a recursive QR algorithm is applied for data reduction. In this first evaluation, the algorithm has been applied to a frequency response matrix (which is a particular set of forced mode of vibration) using a sliding frequency window. The objective of the sliding frequency window is to execute the analysis simultaneously with the data acquisition. Since the pole values and the modal density are obtained from this analysis during the acquisition, the analysis information can be used to help determine the forcing vectors during the experimental data acquisition.

Rost, R. W.↗

Polarization effects and multipolarization SAR

Imaging radar polarimeters are usually implemented using a Synthetic Aperture Radar (SAR) approach to give a high resolution image in two dimensions: range and azimuth. For each pixel in the image a polarimetric SAR gives sufficient information to characterize the polarimetric scattering properties of the imaged area (or target) as seen by the radar. Using a polarimetric SAR system as opposed to a single-polarization SAR system provides significantly more information about the target scattering mechanisms and allows better discrimination between different types of surfaces. In these notes a brief overview of SAR polarimetry is offered. The notes are intended as a text to accompany a lecture on SAR polarimetry as part of an AGARD-NATO course. Covered in the notes are the following: the polarization properties of electromagnetic waves; the concepts of radar scattering and measuring radar backscatter with a SAR; polarization synthesis; scattering matrix, Stokes matrix, and covariance matrix representations of polarimetric SAR data; polarization signature plots; design and calibration of polarimetric SAR systems; polarization filtering for target detection; fitting a simple model to polarimetric SAR measurements of naturally occurring features; and supervised classification of polarimetric SAR data.

Freeman, Anthony↗