Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

The performance of additively manufactured Haynes 282 in supercritical CO 2

The use of supercritical carbon dioxide (sCO 2 ) as a working fluid is garnering interest in next generation power production systems due to the possibility of increased operational efficiencies and lower associated costs. Its implementation requires alloys with excellent high temperature strength and corrosion resistance, which makes Haynes 282® (H282) a suitable candidate. With increasing adoption of additive manufacturing (AM) in the energy industry, there is a need to investigate long-term sCO2 exposure on AM produced materials. Additively manufactured H282 (AM-H282) samples built using laser powder bed fusion in two different orientations were analyzed through imaging, gravimetric analysis, and room-temperature tensile testing before and after 1000-h exposure to CO 2 at 750 °C and 20 MPa. Performed imaging included observation of the sample surfaces and of the material bulk (cross sections) through means of Scanning Electron Microscopy (SEM) and optical microscopy. In comparison to wrought H282, it was found that the exposed material exhibited a similar Cr 2 O 3 oxide protective layer about 2 μm in thickness with additional top-surface TiO 2 oxide and carbon-rich precipitates. It was also similarly observed that internal oxidation was present but limited to a depth of 20 μm, and a 1–3 μm γ’ denuded region appeared to surround all internal and surface oxidation. Thermal aging effects were noted with the precipitation of needle-like structures in the γ/γ’ matrix and a coarsening of the γ’ precipitates from 28 nm to 73 nm. Mass measurements analyzing oxide precipitation revealed a larger increase compared to wrought, representing an approximate 20% difference. Tensile testing results showed similar behavior to wrought with a slight increase in yield strength and a large reduction in elongation in the exposed samples.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Volumetric energy density impact on mechanical properties of additively manufactured 718 Ni alloy

The 718 Ni-based superalloy has gained enormous attention in the additive manufacturing community for its great weldability, allowing for complex geometries to be formed, and its superb mechanical strength. Here we explore the influence of a wide range of major build parameters on microstructures and mechanical properties of 718 Ni alloys. Volumetric energy density appears to be one of the major parameters that captures the relationship between energy input and measured mechanical properties and microstructures of the alloys. A threshold energy density was identified below which the properties of the additively manufactured specimen degrade substantially. Finally, the influence of energy density on the quality of the built specimen simulated using Flow3D AM correlates well with the experimental results.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Analysis of orientation-dependent deformation mechanisms in additively manufactured Zr using in-situ micromechanical testing: Twinning and orientation gradient

Here, orientation-dependent plasticity in zirconium (Zr)-alloy, which is produced through ultrasonic additive manufacturing (UAM) with subsequent hot-isostatic pressing (HIP), was analyzed by recording electron backscattered diffraction (EBSD) data during in-situ micromechanical testing. Three (0001) plane orientations of a hexagonal close-packed (HCP) structure were analyzed parallel to (1) the rolling direction [X||tensile direction (TD)], (2) the build direction [Z], and (3) the transverse direction [Y]. The analysis revealed that the grains with ~<0001>||TD show twin-dominant plasticity with three variants from {10 $\overline{1}$ 2}<$\overline{1}$ 011>; minor slipping with ($10\overline{1}$ 1)[$\overline{2}$ 113], and ($11\overline{2}$ 2)[$\overline{1} \overline{1}$ 23] pyramidal slip has also been observed. However, grains with orientation ~<0001>⊥TD are mainly sensitive to dislocations assisted plasticity-leading to orientation gradients formation. Furthermore, the neck formation was identified as originating from higher populated micro-crack locations and their association with localized plasticity at defect points in the UAM material. These results demonstrate that minimization of impurities to enable grain growth across prior foil interfaces makes HIP an effective methodology for producing Zr plate, with deformation characteristics expected for conventionally manufactured Zr.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Alloying effects on the microstructure and properties of laser additively manufactured tungsten materials

A large body of literature within the additive manufacturing (AM) community has focused on successfully creating stable tungsten (W) microstructures due to significant interest in their application for extreme environments. However, cracking and additional embrittling features at grain boundaries have resulted in poorly performing materials, stymying the application of AM as a manufacturing technique for W. Several alloying strategies, such as ceramic particles and ductile elements, have emerged with the promise to eliminate cracking while simultaneously enhancing stability against recrystallization. Here, in this work, we provide new insights regarding the defects and microstructural features that result from the introduction of ZrC for grain refinement and NiFe as a ductile reinforcement phase – in addition to the resulting thermophysical and mechanical properties. ZrC is shown to promote microstructural stability with increased hardness due to the formation of ZrO 2 dispersoids. Conversely, NiFe forms into micron-scale FCC phase regions within a BCC W matrix, producing enhanced toughness relative to pure AM W. A combination of these effects is realized in the WNiFe + ZrC system and demonstrates that complex chemical environments coupled with the tuning of AM microstructures provides an effective pathway for enabling laser AM W materials with enhanced stability and performance.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Influence of microstructure and temperature on impact toughness of H13 steel produced by binder jet additive manufacturing

Binder Jet Additive Manufacturing (BJAM) is a promising manufacturing pathway to produce H13 steel dies and tooling with complex geometries for applications in high pressure aluminum die casting, hot stamping, and injection molding. While fully dense H13 coupons produced using BJAM have been subjected to detailed microstructure characterization, properties which are critical and relevant to the aforementioned applications, such as impact toughness, have not been reported. Here, this work evaluated the influence of microstructural characteristics and test temperature on the impact toughness of H13 produced by BJAM. Coupons were produced from three different powder size distributions (PSDs), with nominal powder size ranges of −22 μm, 10-32 μm, and 15-53 μm. Coupons were printed, sintered, hot isostatically pressed (HIPed), and heat treated by quenching and tempering. After HIPing, the measured porosities of the different PSDs were all less than 0.015 vol%. The −22 μm PSD BJAM material exhibited the best impact toughness of all three PSDs across the entire test temperature range from 25 to 400 °C, and also exhibited an ambient temperature impact toughness of 10.9 J at a hardness of 46 HRC, equivalent to minimum threshold requirements for premium grade H13. However, all three BJAM PSDs exhibited moderately lower impact toughness than premium grade wrought H13 from RT to 400 °C. We attribute this in part due to the very large prior-austenite grain (PAG) sizes near 400 μm and segregation from former liquid channels leading to greater amounts of carbide precipitation on PAG boundaries. Technical pathways for optimizing processing and chemistry of BJAM H13 to further improve impact toughness are discussed.

Binder jet additive manufacturing↗
DOE OSTI2023

Towards the applications of mechanophore incorporated feedstocks for additive manufacturing

The ability to additively-manufacture mechanically responsive molecules, known as mechanophores (MPs), that are incorporated into polymer feedstocks provides opportunities for self-healing, real-time damage detection, and improvements in quality assurance and control capabilities to several industries (wind energy technology, building and construction, etc.) who are adopting additive manufacturing (AM). However, before the applications are realized and industrially adopted, further research and development regarding MP-incorporated AM feedstock availability, production scale-up, and processability and printability is needed. Here, the goal of this review is to bridge the gap between the bench top and real world applications of AM of MPs by identifying high impact application spaces and highlighting the challenges that need to be overcome for widespread adoption. The state-of-the-art of AM of MP-incorporated feedstocks is reviewed, followed by a discussion of potential future applications, current challenges, and research areas that work toward commercialization of AM of MP-incorporated feedstocks.

36 MATERIALS SCIENCE↗
DOE OSTI2019

A comprehensive study on the fabrication and characterization of Ti–48Al–2Cr–2Nb preforms manufactured using electron beam melting

This feasibility study examines the additive manufacturing of Ti–48Al–2Cr–2Nb preforms in a quest to make more complex engine components from this promising but hard to machine, brittle material. The preforms are built using the electron beam melting technique; hot isostatic pressing (HIP) was performed as the only post-process. Microstructural characterizations were carried with scanning electron microscopy techniques, X-ray diffraction and X-ray computed tomography while mechanical properties were obtained via tensile testing. We exploited computational thermodynamic modeling (widely known as CALPHAD) approach to investigate the phase stability pertinent to Nb and Cr modified TiAl. Defect-free structures were obtained in the HIPed condition with mechanical behavior comparable to/better than traditionally manufactured counterparts. Equiaxed duplex microstructures were achieved in the as-built condition that were sustained post-HIP. The effect of the build conditions and phase transformation kinetics on the observed microstructures is discussed. Furthermore, the microstructure-mechanical behavior relationship is also discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Characterization of nonlinear ultrasonic waves behavior while interacting with poor interlayer bonds in large-scale additive manufactured materials

Over the past decades, researchers have developed several nonlinear ultrasonic techniques for quality control of materials commonly used in different applications. Owing to the superior sensitivity of nonlinear ultrasound waves to small defects such as micro-cracks, their applicability in different nondestructive testing (NDT) problems has been investigated in numerous studies. These studies utilize frequency domain analysis to detect the generation of higher harmonics because of the formation of defects in the inspected medium. Frequency domain analysis based on the Fourier transform is a significant approach used in linear systems; however, it may not perform adequately on nonlinear systems. Hence, studies on nonlinear dynamics and physics consider analyzing systems' behavior in the phase-space domain. In contrast to the frequency domain analysis, which can result in information loss, analysis in the phase-space domain retains all the information regarding a system's states. Here, we investigate the nonlinearities induced by poor interlayer bonding in polymer-based additive manufactured parts in the phase-space domain. It is convenient to characterize the nonlinearity in the phase-space domain because it provides a geometrical representation of a system's states. Two types of low quality interlayer bond are considered. The first type is simulated artificially while the second type is manufactured by reducing the bond quality during the printing process. The analysis verified that the received ultrasonic signals exhibit classical nonlinear behavior in the phase-space domain while interacting with simulated poor interlayer bonds. In addition, the results showed that the behavior of ultrasonic waves is amplitude-dependent and evolves into models that have not been previously reported. Furthermore, Largest Lyapunov Exponent (LLE) is used to quantify the behavior of nonlinear ultrasonic waves while interacting with poor interlayer bonds. Using LLE, it was observed that the divergence rate of the phase-space trajectories depends on the amplitude of the excitation. This observation quantitatively proves that nonlinear behavior of ultrasound while interacting with poor interlayer bonds can be amplitude-dependent. The results of both simulated and inherent poor interlayer bond cases showed that LLE can be used as a reliable quantitative damage-sensitive feature to detect and potentially characterize weak bonds, which are difficult to detect using conventional approaches. Additionally, the reported results in the phase-space domain provide a basis for proposing a new mathematical model for ultrasonic waves interacting with poor interlayer bonds.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A NEA review on innovative structural materials solutions, including advanced manufacturing processes for nuclear applications based on technology readiness assessment

The Nuclear Energy Agency (NEA) Expert Group on Innovative Structural Materials (EGISM) was established in 2008 under the guidance of the Nuclear Science Committee (NSC). Its objectives are to conduct joint and comparative studies to support the development, selection and characterisation of innovative structural materials that can be implemented in advanced nuclear fuel cycles, under long service lifetime and extreme conditions, such as high temperature, high dose/dose rate and corrosive chemical environments. In this context of growing interest and initiatives, the EGISM initiated at the beginning of 2018 an activity among its members to: Identify, in a non-exhaustive way, the currently existing programs on innovative materials and fabrication processes in NEA member countries and China; Establish a first cartography of the activities that are underway on these topics and identify common subjects and thematic; Propose a Technology Readiness Level scale to estimate the maturity of both innovative materials and fabrication processes; Carry out a reflection on what the enablers are to quickly climb this TRL scale, as well as the obstacles, in order to identify solutions to overcome them. This paper first gives definitions shared between the EGISM members on what are considered as advanced structural materials solutions. Next, some international initiatives for the accelerated development of high performance materials are presented both in non-nuclear and nuclear fields. Then, the methodology adopted for technology readiness assessment is explained. A non-exhaustive synthesis of the projects identified among the EGISM members on innovative structural materials and advanced manufacturing solutions such as additive manufacturing is presented. The TRL level of these projects is evaluated. A focus is also made on some of these projects to illustrate and explain the TRLs chosen as well as highlighting enablers or obstacles identified to climbing up the TRL scale.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Power performance and loads characterization of laboratory-scale cross-flow rotors fabricated using additive manufacturing

Tidal energy conversion is a relatively new application for additive manufacturing (AM), where the focus has been on fabricating axial-flow turbine blades. AM techniques add material precisely where it is needed, creating more complex shapes with less waste. Cross-flow rotor geometry presents an opportunity for AM to improve rotor performance by fabricating features that cannot be created economically via conventional manufacturing. The challenges associated with using AM in cross-flow design include water resistance and degradation over time while retaining a level of quality equivalent to conventionally machined parts. In this work, AM materials were tested by environmentally conditioning samples in a seawater tank for 5 months, followed by performance and phase-resolved load testing of laboratory-scale rotors in a hydraulic flume. We found that while metals like titanium and Inconel have excellent performance in marine environments, achieving the desired geometry and performance is difficult. Thermoplastics degraded in seawater but were easier to form into desired geometries and could exceed the performance of an aluminum control rotor. Warping and surface finish were significant detractors from AM rotor performance. These results suggest that the primary benefits of using AM for cross-flow rotors is to quickly fabricate and test unconventional rotor geometries.

16 TIDAL AND WAVE POWER↗
DOE OSTI2016

A novel method for production of spherical Ti-6Al-4V powder for additive manufacturing

We report a novel method was developed to produce spherical Ti-6Al-4V powder for advanced near-net-shape manufacturing processes including additive manufacturing and powder injection molding. The new process synergistically integrates a few common low-cost processing techniques including granulation, sintering, and de-oxygenation to produce spherical Ti alloy powders without relying on costly melting and atomizing techniques. This new granulation-sintering-deoxygenation (GSD) process can use low-cost source powders such as scrap Ti as the raw material. The spherical Ti-6Al-4V powder produced using this process has controlled particle size distribution and low oxygen content (< 0.15%), which meet the Aerospace Material Specification (AMS-4998) for spherical Ti-6Al-4V powder.

42 ENGINEERING↗
DOE OSTI2017

Solidification and solid-state transformation sciences in metals additive manufacturing

Additive manufacturing (AM) of metals is rapidly emerging as an established manufacturing process for metal components. Unlike traditional metals fabrication processes, metals fabricated via AM undergo localized thermal cycles during fabrication. As a result, AM presents the opportunity to control the liquid-solid phase transformation, i.e. material texture. But, thermal cycling presents challenges from the standpoint of solid-solid phase transformations. We will discuss the opportunities and challenges in metals AM in the context of texture control and associated solid-solid phase transformations in Ti-6Al-4V and Inconel 718.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Additive manufacturing: Toward holistic design

Here, additive manufacturing offers unprecedented opportunities to design complex structures optimized for performance envelopes inaccessible under conventional manufacturing constraints. Additive processes also promote realization of engineered materials with microstructures and properties that are impossible via traditional synthesis techniques. Enthused by these capabilities, optimization design tools have experienced a recent revival. The current capabilities of additive processes and optimization tools are summarized briefly, while an emerging opportunity is discussed to achieve a holistic design paradigm whereby computational tools are integrated with stochastic process and material awareness to enable the concurrent optimization of design topologies, material constructs and fabrication processes.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Influence of hot isostatic pressing on the performance of aluminum alloy fabricated by ultrasonic additive manufacturing

Ultrasonic additive manufacturing (UAM) is a solid-state manufacturing technique employing principles of ultrasonic welding coupled with mechanized tape layering to fabricate fully functional parts. However, UAM-fabricated parts often exhibit a reduction in strength when loaded normal to the welding interfaces (Z-direction). Here, the effect of hot isostatic pressing (HIP) on UAM builds of aluminum alloy was explored. Tensile testing and microstructure characterization were conducted; it was established that HIP eliminated the brittle Z-direction fracture and improved the strength and ductility of the Z-direction specimens. HIP eliminated voids and produced recrystallized structure; however, welding interfaces survived the HIP treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Porosity evolution under increasing tension in wire-arc additively manufactured aluminum using in-situ micro-computed tomography and convolutional neural network

Internal defects such as porosities are often formed in additively manufactured metal components. The pores nucleate, grow, and coalesce to form cracks under loads, leading to eventual catastrophic failure. Here, in this paper, the full-field porosity evolution, including pore growth and coalescence in a wire-arc additively manufactured (WAAM) aluminum alloy cylinder under tension is observed with in-situ X-ray micro-computed tomography (μCT). The pore size distribution, density, and tensile stress are calculated from the volumetric images analyzed by a convolutional neural network (CNN) algorithm, which provides rapid analysis of 12,950 slice images from μCT volumetric images at the reference state and 13 tensile strains. The results show the quantitative evolution of the growth and coalescence of macropores under tension. A strong correlation is found between the local pore volume fraction and the true tensile stress when the tensile strain is larger than 5%.

36 MATERIALS SCIENCE↗
DOE OSTI2022

An additively-manufactured molten salt-to-supercritical carbon di-oxide primary heat exchanger for solar thermal power generation – Design and techno-economic performance

The design and techno-economic performance of a compact additively manufactured (AM) molten salt (MS)-to-supercritical carbon di-oxide (sCO2) primary heat exchanger (PHE) for solar thermal application is described. The PHE design consists of sCO2 flow through an array of microscale pin fins while the MS flows through mm-scale rectangular channels. Constraints imposed by AM using laser powder bed fusion method are considered in the design. Structural and fluid flow simulations are performed to arrive at a viable design of the core and headers. A simplified one-dimensional steady state model for the PHE is developed including the impact of surface roughness from the AM process. A process-based cost model is used to determine the tradeoff between thermofluidic design and manufacturing cost. A parametric study is performed using the thermo-fluidic and cost models to determine the set of geometrical and flow variables that result in high power density and low cost, while restricting the pressure drop on the sCO2 side to less than 2% of line pressure. Flow rates of MS and sCO2 were varied over heat capacity rate ratios ranging from 0.2 to 1. Results indicate that it is possible to design a low-pressure drop AM PHE with an effectiveness of 90% and a power density in excess of 10 MW/m3 (including headers). Fabrication of representative nickel superalloy specimens are shown to demonstrate that low-porosity parts with the requisite dimensional tolerance of PHE core can be generated.

14 SOLAR ENERGY↗
DOE OSTI2024

Stress localization investigation of additively manufactured GRCop-42 thin-wall structure

A full-field crystal plasticity (CP) framework is presented for the GRCop-42 alloy to study microscopic mechanical behavior and local stress heterogeneities. The microstructures of additively manufactured (AM) materials are often unique relative to conventionally processed materials, and the local thermal histories drive these differences during the build process. These thermal histories depend on the process parameters (laser power, scan speed, and scan strategy) and the part geometry. Prior research has shown that the mechanical properties of thin-walled structures can vary significantly with wall thickness due to changes in the thermal boundary conditions during manufacturing. It is, therefore, desirable to perform CP simulations based on the phenomenological constitutive model to predict the local mechanical responses induced by microstructural heterogeneities. This work generates representative microstructures based on experimentally collected grain information (i.e., texture) for grain scale stress analysis, and the material constitutive parameters are calibrated using the experimental mechanical testing data. Here, we specifically investigated the effect of crystallographic texture and grain morphologies on the size-dependent mechanical properties of AM GRCop-42. The selection of appropriate material properties for implementing an effective free surface boundary condition and the influence of adjacent buffer layers are also discussed. Analysis of local field results reveals a strong correlation between stress localization and the initial grain orientation. However, no significant relationship between the misorientation of the individual adjacent grains and the average misorientation is observed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Thermal Barrier Coatings Overview: Design, Manufacturing, and Applications in High-Temperature Industries

Today’s competitive world economy is creating an indispensable demand for increased efficiency of engineering components that operate in harsh environments (i.e., very high-temperature, corrosive, or neutron irradiation environments), for applications in the energy, automotive, aerospace, electronics, and power industries. Increased research is being done on thermal barrier coatings (TBCs) for protecting such components, since the versatility of manufacturing techniques and the scale of deployment result in increased life, economics, performance, and durability. This review focuses on the advances that led to using TBCs for component life extension and, more recently, as an integral part of advanced component design for high-temperature and other types of harsh environments, such as those found in nuclear-related applications. Furthermore, factors that led to state-of-the-art advanced coating-fabrication techniques [e.g., electron-beam physical vapor deposition (EB-PVD), plasma spray deposition, and electrophoretically deposited TBCs, as well as functionally graded material (FGM) manufacturing] have also been emphasized in current coating R&D. This review explores the current state of TBCs, i.e., the latest advances regarding their fabrication and performance, associated challenges, and recommendations for their future use in aerospace, nuclear, high-temperature, or otherwise harsh environments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗