Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MILITARY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92

STOL landing thrust: Reverser jet flowfields

Analysis tools and modeling concepts for jet flow fields encountered upon use of thrust reversers for high performance military aircraft are described. A semi-empirical model of the reverser ground wall jet interaction with the uniform cross flow due to aircraft forward velocity is described. This ground interaction model is used to demonstrate exhaust gas ingestion conditions. The effects of control of exhaust jet vector angle, lateral splay, and moving versus fixed ground simulation are discussed. The Adler/Baron jet-in-cross flow model is used in conjunction with three dimensional panel methods to investigate the upper surface jet induced flow field.

Kotansky, D. R.↗

Compound cycle engine for helicopter application

The Compound Cycle Engine (CCE) is a highly turbocharged, power compounded, ultra-high power density, light-weight diesel engine. The turbomachinery is similar to a moderate pressure ratio, free power turbine engine and the diesel core is high speed and a low compression ratio. This engine is considered a potential candidate for future military light helicopter applications. This executive summary presents cycle thermodynamic (SFC) and engine weight analyses performed to establish general engine operating parameters and configuration. An extensive performance and weight analysis based on a typical two hour helicopter (+30 minute reserve) mission determined final conceptual engine design. With this mission, CCE performance was compared to that of a T-800 class gas turbine engine. The CCE had a 31% lower-fuel consumption and resulted in a 16% reduction in engine plus fuel and fuel tank weight. Design SFC of the CCE is 0.33 lb-HP-HR and installed wet weight is 0.43 lbs/HP. The major technology development areas required for the CCE are identified and briefly discussed.

Castor, Jere G.↗

Preliminary structural design of composite main rotor blades for minimum weight

A methodology is developed to perform minimum weight structural design for composite or metallic main rotor blades subject to aerodynamic performance, material strength, autorotation, and frequency constraints. The constraints and load cases are developed such that the final preliminary rotor design will satisfy U.S. Army military specifications, as well as take advantage of the versatility of composite materials. A minimum weight design is first developed subject to satisfying the aerodynamic performance, strength, and autorotation constraints for all static load cases. The minimum weight design is then dynamically tuned to avoid resonant frequencies occurring at the design rotor speed. With this methodology, three rotor blade designs were developed based on the geometry of the UH-60A Black Hawk titanium-spar rotor blade. The first design is of a single titanium-spar cross section, which is compared with the UH-60A Black Hawk rotor blade. The second and third designs use single and multiple graphite/epoxy-spar cross sections. These are compared with the titanium-spar design to demonstrate weight savings from use of this design methodology in conjunction with advanced composite materials.

Nixon, Mark W.↗

Workshop on Workload and Training, and Examination of their Interactions: Executive summary

The goal of the workshop was to bring together experts in the fields of workload and training and representatives from the Dept. of Defense and industrial organizations who are reponsible for specifying, building, and managing advanced, complex systems. The challenging environments and requirements imposed by military helicopter missions and space station operations were presented as the focus for the panel discussions. The workshop permitted a detailed examination of the theoretical foundations of the fields of training and workload, as well as their practical applications. Furthermore, it created a forum where government, industry, and academic experts were able to examine each other's concepts, values, and goals. The discussions pointed out the necessity for a more efficient and effective flow of information among the groups respresented. The executive summary describes the rationale of the meeting, summarizes the primary points of discussion, and lists the participants and some of their summary comments.

Donchin, Emanuel↗

Optimal flight trajectories in the presence of windshear, 1984-86

Optimal flight trajectories were determined in the presence of windshear and guidance schemes were developed for near optimum flight in a windshear. This is a wind characterized by sharp change in intensity and direction over a relatively small region of space. This problem is important in the takeoff and landing of both civilian airplanes and military airplanes and is key to aircraft saftey. The topics covered in reference to takeoff problems are: equations of motion, problem formulation, algorithms, optimal flight trajectories, advanced guidance schemes, simplified guidance schemes, and piloting strategies.

Miele, A.↗

Network protocols for real-time applications

The Fiber Distributed Data Interface (FDDI) and the SAE AE-9B High Speed Ring Bus (HSRB) are emerging standards for high-performance token ring local area networks. FDDI was designed to be a general-purpose high-performance network. HSRB was designed specifically for military real-time applications. A workshop was conducted at NASA Ames Research Center in January, 1987 to compare and contrast these protocols with respect to their ability to support real-time applications. This report summarizes workshop presentations and includes an independent comparison of the two protocols. A conclusion reached at the workshop was that current protocols for the upper layers of the Open Systems Interconnection (OSI) network model are inadequate for real-time applications.

Johnson, Marjory J.↗

Simulation and analysis of airborne antenna radiation patterns

The objective is to develop an accurate and efficient analytic solution for predicting high frequency radiation patterns of fuselage-mounted airborne antennas. This is an analytic study of airborne antenna patterns using the Uniform Geometrical Theory of Diffraction (UTD). The aircraft is modeled in its most basic form so that the solution is applicable to general-type aircraft. The fuselage is modeled as a perfectly conducting composite ellipsoid; whereas, the wings, stabilizers, nose, fuel tanks, and engines, are simulated as perfectly conducting flat plates that can be attached to the fuselage and/or to each other. The composite-ellipsoid fuselage model is necessary to successfully simulate the wide variety of real world fuselage shapes. Since the antenna is mounted on the fuselage, it has a dominant effect on the resulting radiation pattern so it must be simulated accurately, especially near the antenna. Various radiation patterns are calculated for commercial, private, and military aircraft, and the Space Shuttle Orbiter. The application of this solution to numerous practical airborne antenna problems illustrates its versatility and design capability. In most cases, the solution accuracy is verified by the comparisons between the calculated and measured data.

Kim, J. J.↗

A VHSIC general purpose processor

The very high speed integrated circuit (VHSIC) program offers NASA and its contractors assured availability of military specification embedded computer components and integrated computer aided design/computer aided engineering and software development support that result in low system life costs for data management systems on the space station and the Earth Observatory Satellite. Viewgraphs given review progress in both the Department of Defense VHSIC program and the NASA VHSIC related insertion development of a general purpose processor are presented.

Benz, H. F.↗

A strategy for advancing tilt-rotor technology

Tilt-rotor technology has many features which make it a very promising development in aviation which might have application to a wide variety of transportation and logistics situations. However, aside from military applications and rather specialized industrial applications, little is known regarding the potential of tilt-rotor for commercial transportation and hence it is difficult to plan a development program which would gain support and be likely to produce a stream of significant benefits. The purpose is to attempt to provide some of this information in a manner that would be useful for preparing a strategy for development of tilt-rotor aircraft technology. Specifically, the objectives were: to identify promising paths of development and deployment of tilt-rotor aircraft technology in the air transportation system considering both benefits and disbenefits, and to identify any particular groups that are likely to benefit significantly and propose plans for gaining their support of research and development of this technology. Potential advantages of the tilt-rotor technology in the context of air transportation as a door-to-door system were identified, and then promising paths of development of such tilt-rotor systems were analyzed. These then lead to recommendations for specific studies, information dissemination and development of awareness of the tilt-rotor among specific transport-related groups.

Morlok, Edward K.↗

Micromechanics of compression failures in open hole composite laminates

The high strength-to-weight ratio of composite materials is ideally suited for aerospace applications where they already are used in commercial and military aircraft secondary structures and will soon be used for heavily loaded primary structures. One area impeding the widespread application of composites is their inherent weakness in compressive strength when compared to the tensile properties of the same material. Furthermore, these airframe designs typically contain many bolted or riveted joints, as well as electrical and hydraulic control lines. These applications produce areas of stress concentration, and thus, further complicate the compression failure problem. Open hole compression failures which represent a typical failure mode for composite materials are addressed.

Guynn, E. Gail↗

Air Force electrochemical power research and technology program for space applications

An overview is presented of the existing Air Force electrochemical power, battery, and fuel cell programs for space application. Present thrusts are described along with anticipated technology availability dates. Critical problems to be solved before system applications occur are highlighted. Areas of needed performance improvement of batteries and fuel cells presently used are outlined including target dates for key demonstrations of advanced technology. Anticipated performance and current schedules for present technology programs are reviewed. Programs that support conventional military satellite power systems and special high power applications are reviewed. Battery types include bipolar lead-acid, nickel-cadmium, silver-zinc, nickel-hydrogen, sodium-sulfur, and some candidate advanced couples. Fuel cells for pulsed and transportation power applications are discussed as are some candidate advanced regenerative concepts.

Allen, Douglas↗

All-digital jets are taking off

The functions and advantages of second-generation digital avionics systems are described. These digital systems have increased integration, increased reliability and flexibility, and improved man-machine interface, and they provide increases in the mean time between removal of line-replacable units and fuel savings. Different redundant processors and software are utilized to achieve fault-tolerance performance of flight control systems. The improved landing capabilities, front-panel instruments, sidestick controllers, back-lighted liquid-crystal displays, and fly-by-wire system possible with digital avionics are examined. The applications of digital avionics to military and commercial aircraft are discussed and examples are provided.

Spitzer, C. R.↗

A new meaning to 'flying the desk'

A unique advanced transport flight station design is described. The various systems and displays of the design are described, including: the configuration; switches; tailored logic/artificial intelligence; primary flight controllers; front panel displays; primary flight/navigation display; engine power/status, approach charts, and weather display; the Advisory, Caution, and Warning System/Cockpit Display of Traffic Information display; checklist/functional systems display; head-up display; voice command and response system; Flight Management Computer system; and integrated communications/navigation system. The application of the flight station to military research is briefly discussed.

Sexton, G. A.↗

Requirement analysis of an intelligent, redundant, actuation system

The reliability and fault tolerance requirements of integrated, critical, digital fly-by-wire control systems for advanced military and civil aircraft requires redundant, reconfigurable implementations of the actuation system. An effective way for controlling the actuators and implementing the required fault detection and reconfiguration strategies is by means of dedicated microprocessors. This paper describes a laboratory implementation of a flexible intelligent redundant actuation system capable of demonstrating the concept and analyzing a variety of configurations and technical issues.

De Feo, P.↗

SP-100 missions overview

This paper reviews both general and specific mission applications for an SP-100 nuclear power subsystem sized for the 10-kWe to 1000-kWe power range. Military applications are treated in a general manner. Four civil mission applications are treated in more detail. Market projection and mission performance data as a function of power are shown.

Wallace, Richard A.↗

Avionics electromagnetic interference immunity and environment

Aircraft electromagnetic spectrum and radio frequency (RF) field strengths are charted, profiling the higher levels of electromagnetic voltages encountered by the commercial aircraft wiring. Selected military, urban, and rural electromagnetic field levels are plotted and provide a comparison of radiation amplitudes. Low frequency magnetic fields and electric fields from 400 H(Z) power systems are charted versus frequency and wire separation to indicate induced voltages on adjacent or neighboring circuits. Induced EMI levels and attenuation characteristics of electric, magnetic, RF fields, and transients are plotted and graphed for common types of wire circuits. The significance of wire circuit returns and shielding is emphasized to highlight the techniques that help block the paths of electromagnetic interference and maintain avionic interface signal quality.

Clarke, C. A.↗

Description of an aircraft lightning and simulated nuclear electromagnetic pulse (NEMP) threat based on experimental data

Lightning data obtained by measuring the surface electromagnetic fields on a CV-580 research aircraft during 48 lightning strikes between 1500 and 18,000 feet in central Florida during the summers of 1984 and 1985, and nuclear electromagnetic pulse (NEMP) data obtained by surface electromagnetic field measurements using a 1:74 CV-580 scale model, are presented. From one lightning event, maximum values of 3750 T/s for the time rate of change of the surface magnetic flux density, and 4.7 kA for the peak current, were obtained. From the simulated NEMP test, maximum values of 40,000 T/s for the time rate of change of the surface magnetic flux density, and 90 A/sq m for the total normal current density, were found. The data have application to the development of a military aircraft lightning/NEMP standard.

Rustan, Pedro L., Jr.↗

Liner cooling research at NASA Lewis Research Center

Described are recently completed and current advanced liner research applicable to advanced small gas turbine engines. Research relating to the evolution of fuel efficient small gas turbine engines capable of meeting future commercial and military aviation needs is currently under way at NASA Lewis Research Center. As part of this research, a reverse-flow combustor geometry was maintained while different advanced liner wall cooling techniques were investigated and compared to a baseline combustor. The performance of the combustors featuring counterflow film-cooled (CFFC) panels, transpiration cooled liner walls (TRANS), and compliant metal/ceramic (CMC) walls was obtained over a range of simulated flight conditions of a 16:1 pressure ratio gas turbine engine and fuel/air ratios up to 0.034. All the combustors featured an identical fuel injection system, identical geometric configuration outline, and similar designed internal aerothermodynamics.

Acosta, Waldo A.↗