Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GET”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

In situ measurements of light extinction of stratospheric aerosols

The extinction coefficient of ambient aerosol particles was measured using a multiple transverse cell (White Cell) with an effective path length of 100 m. Measurements were performed at seven fixed wavelengths in the visible region using a white light source and an interference filter set with 2 nm bandwidth and center wavelengths of 405.5, 450, 500, 550, 600, 650, and 692.5 nm. The total air flow in the system was 16.7 1/min; the volume of the chamber is close to 10 liters. It takes about one minute to fill the chamber with particles homogeneously, but it needs up to five minutes to get the chamber particle-free. Before measuring the aerosol, the transmission of the particle-free air is determined; then the aerosol passes through the chamber for a period of ten minutes; after this the transmission of particle-free ambient air is measured again for eight minutes. All times are subject to change. At present the measurements are done with a frequency of 1 Hz, but an increase of up to 30 Hz is possible. The lower detection limit of the used White Cell is 3.4 by 10(exp -06) per m. This is sufficient for measuring the extinction coefficient during most tropospheric and some stratospheric conditions. It will be necessary to increase the sensitivity by a factor of ten when measurements under the clearest stratospheric conditions take place.

Metzig, Gunthard↗
NASA NTRS1991

The electric field changes and UHF radiations caused by the triggered lightning in Japan

In the rocket triggered lightning experiment of fiscal 1989, researchers observed electromagnetic field changes and UHF electromagnetic radiation accompanying rocket triggered lightning. It was found that no rapid changes corresponding to the return stroke of natural lightning were observed in the electric field changes accompanying rocket triggered lightning. However, continuous currents were present. In the case of rocket triggered lightning to the tower, electromagnetic field changes corresponding to the initiation of triggered lightning showed a bipolar pulse of a relatively large amplitude. In contrast, the rocket triggered lightning to the ground did not have such a bipolar pulse. The UHF radiation accompanying the rocket triggered lightning preceded the waveform portions corresponding to the first changes in electromagnetic fields. The number of isolated pulses in the UHF radiation showed a correlation with the time duration from rocket launching up to triggered lightning. The time interval between consecutive isolated pulses tended to get shorter with the passage of time, just like the stepped leaders of natural lightning.

Kawasaki, Zen-Ichiro↗
NASA NTRS1990

A user interface development tool for space science systems Transportable Applications Environment (TAE) Plus

The Transportable Applications Environment Plus (TAE PLUS), developed at NASA's Goddard Space Flight Center, is a portable What You See Is What You Get (WYSIWYG) user interface development and management system. Its primary objective is to provide an integrated software environment that allows interactive prototyping and development that of user interfaces, as well as management of the user interface within the operational domain. Although TAE Plus is applicable to many types of applications, its focus is supporting user interfaces for space applications. This paper discusses what TAE Plus provides and how the implementation has utilized state-of-the-art technologies within graphic workstations, windowing systems and object-oriented programming languages.

Szczur, Martha R.↗
NASA NTRS1990

Optimization of the alexandrite laser tuning elements for a water vapor lidar

An overview of some of the developments completed on an alexandrite laser for making water vapor DIAL measurements is presented in this paper. A computer control for active stabilization of the two intracavity etalons has been implemented and recently tested in an aircraft environment. Long-term frequency drift (i.e., 2 hours) of less than 0.7 pm has been observed in the laboratory. An alignment technique to get the optimum free spectral range ratio for the two etalons is also developed.

Ponsardin, Patrick↗
NASA NTRS1991

A summary of existing and planned experiment hardware for low-gravity fluids research

NASA's ground-based and space-based low-gravity facilities are summarized, and an overview of selected experiments that have been developed for use in these facilities is presented. A variety of ground-based facilities (drop towers and aircraft) used to conduct low-gravity experiments for in-space experimentation are described. Capabilities that are available to the researcher and future on-orbit fluids facilities are addressed. The payload bay facilities range from the completely self-contained, relatively small get-away-special canisters to the Materials Science Laboratory and to the larger Spacelab facilities that require crew interaction.

Hill, Myron E.↗
NASA NTRS1990

NASA secondary payload plans, policies and requirements

A review is presented of the secondary or piggyback flight opportunities that are presently available along with an overview of NASA's secondary payload plans, policies and requirements. When there is excess capacity on either the Space Shuttle or an expendable launch vehicle (ELV), a logical step is to carry a secondary payload to provide a relatively low-cost launch for small satellites. NASA has already flown more than a dozen piggyback payloads on the Delta rocket. The Small Expendable Deployment system experiment is currently planned as the first of small space experiments launched as a piggyback on an ELV. Some details are provided on various secondary payload flight opportunities aboard the Space Shuttle including the Get-Away Special Canister Program, the complex autonomous payload, the Hitchhiker Program, and the middeck lockers concept. Also described are several secondary payload possibilities utilizing ELVs.

Poniatowski, Karen S.↗
NASA NTRS1990

The role of the low-speed wind tunnel in transition research

The study addresses the present transition research directed to the prediction of transition on the wings of modern transonic aircraft and concentrates on the stability of the types of boundary layers that arise on real swept wings in compressible flow. The need to perform experiments to get better insights into such aspects of transition as receptivity, types of nonlinear interaction, development of irregular chaotic motion, and the final breakdown stage is emphasized. The use of low-speed wind tunnel is discussed, and focus is placed on control, surface quality, and instrumentation.

Gaster, Michael↗
NASA NTRS1990

Vibration and wave propagation characteristics of multisegmented elastic beams

Closed form analytical solutions are derived for the vibration and wave propagation of multisegmented elastic beams. Each segment is modeled as a Timoshenko beam with possible inclusion of material viscosity, elastic foundation and axial forces. Solutions are obtained by using transfer matrix methods. According to these methods formal solutions are first constructed which relate the deflection, slope, moment and shear force of one end of the individual segment to those of the other. By satisfying appropriate continuity conditions at segment junctions, a global 4x4 matrix results which relates the deflection, slope, moment and shear force of one end of the beam to those of the other. If any boundary conditions are subsequently invoked on the ends of the beam one gets the appropriate characteristic equation for the natural frequencies. Furthermore, by invoking appropriate periodicity conditions the dispersion relation for a periodic system is obtained. A variety of numerical examples are included.

Nayfeh, Adnan H.↗
NASA NTRS1991

Cross sections and rate coefficients for inelastic interactions of heavy particles

The existing analytical inelastic cross-sections for direct atom-atom ionizing collisions of Firsov (1959), Fleischmann et al. (1972), and Drawin (1968) are discussed. General analytical expressions for direct ionization cross-sections in atom-atom collisions are derived. The main advantage of the present cross-sections is their generality, simplicity, and overall accuracy, which is acceptable in most applications and is better than the overall accuracy of the cross-sections of Firsov, Fleischmann et al., and Drawin. The atom-atom interaction is considered as a superposition of all the pairwise interactions between the test particle and all the electrons of the outer nl shell of the target atom. Such a picture of atom-atom collision is acceptable at low- and medium-impact energies because then the electrons of the outer shell of the target atom are most likely the ones that get ionized. At high-impact energy, the picture becomes inaccurate because of strong overlapping of the atomic shells.

Kunc, J. A.↗
NASA NTRS1991

The SIR-C/X-SAR synthetic aperture radar system

SIR-C/X-SAR, a three-frequency radar to be flown on the Space Shuttle in September 1993, is described. The SIR-C system is a two-frequency radar operating at 1250 MHz (L-band) and 5300 MHz (C-band), and is designed to get four-polarization radar imagery at multiple surface angles. The X-SAR system is an X-band imaging radar operating at 9600 MHz. The discussion covers the mission concept; system design; hardware; RF electronics; digital electronics; command, timing, and telemetry; and testing.

Jordan, Rolando L.↗
NASA NTRS1990

Dielectric function of InGaAs in the visible

Measurements are reported of the dielectric function of thermodynamically stable In(x)Ga(1-x)As in the composition range 0.3 equal to or less than X = to or less than 0.7. The optically thick samples of InGaAs were made by molecular beam epitaxy (MBE) in the range 0.4 = to or less than X = to or less than 0.7 and by metal-organic chemical vapor deposition (MOCVD) for X = 0.3. The MBE made samples, usually 1 micron thick, were grown on semi-insulating InP and included a strain release structure. The MOCVD sample was grown on GaAs and was 2 microns thick. The dielectric functions were measured by variable angle spectroscopic ellipsometry in the range 1.55 to 4.4 eV. The data was analyzed assuming an optically thick InGaAs material with an oxide layer on top. The thickness of this layer was estimated by comparing the results for the InP lattice matched material, i.e., X = 0.53, with results published in the literature. The top oxide layer mathematically for X = 0.3 and X = 0.53 was removed to get the dielectric function of the bare InGaAs. In addition, the dielectric function of GaAs in vacuum, after a protective arsenic layer was removed. The dielectric functions for X = 0, 0.3, and 0.53 together with the X = 1 result from the literature to evaluate an algorithm for calculating the dielectric function of InGaAs for an arbitrary value of X (0 = to or less than X = to or less than 1) were used. Results of the dielectric function calculated using the algorithm were compared with experimental data.

Alterovitz, S. A.↗
NASA NTRS1992

Software For Allocation Of Tolerances

Collection of computer programs being developed to assist engineers in allocating tolerances to dimensions of components and assemblies. System reflects tolerancing expertise of design and manufacturing engineers; helps engineers maintain comprehensive tolerancing policy and overview that might otherwise get lost when attending to details of design and manufacturing processes. Necessary to allocate tolerances for three main reasons: tolerances allow for variations in dimensions of components as manufactured; assembly of two or more components, dimensions lie between specified limits; and part replaced must fit in place.

Fernandez, Ken↗
NASA NTRS1991

Collision probabilities in the presence of nebular gas drag

We are developing a model to determine what fraction of the planetesimals would have hit a protoplanet on their sunward journey as opposed to having a close approach and passing into an inferior orbit. The model involves direct numerical integration of restricted-three-body orbits using a predictor-corrector integrator. A simple gas drag law with a v(exp 2) dependence was also included in the equations of motion. Runs of 100 to 500 particles were already performed, while some future runs may require several times this number in order to get good impact statistics. All planetesimals start in superior orbits with semi-major axes 5 to 10 R(sub H) from the protoplanets, where R(sub H) is the protoplanet's Hill Sphere radius. The orbit is followed until the planetesimal passed into an inferior orbit at least 10 R(sub H) from the protoplanet. This process typically requires 10(exp 4) to 10(exp 5) orbits.

Kary, David M.↗
NASA NTRS1989

Sparse distributed memory

Sparse distributed memory was proposed be Pentti Kanerva as a realizable architecture that could store large patterns and retrieve them based on partial matches with patterns representing current sensory inputs. This memory exhibits behaviors, both in theory and in experiment, that resemble those previously unapproached by machines - e.g., rapid recognition of faces or odors, discovery of new connections between seemingly unrelated ideas, continuation of a sequence of events when given a cue from the middle, knowing that one doesn't know, or getting stuck with an answer on the tip of one's tongue. These behaviors are now within reach of machines that can be incorporated into the computing systems of robots capable of seeing, talking, and manipulating. Kanerva's theory is a break with the Western rationalistic tradition, allowing a new interpretation of learning and cognition that respects biology and the mysteries of individual human beings.

Denning, Peter J.↗
NASA NTRS1991

Automating a spacecraft electrical power system using expert systems

Since Skylab, Marshall Space Flight Center (MSFC) has recognized the need for large electrical power systems (EPS's) in upcoming Spacecraft. The operation of the spacecraft depends on the EPS. Therefore, it must be efficient, safe, and reliable. In 1978, as a consequence of having to supply a large number of EPS personnel to monitor and control Skylab, the Electrical power Branch of MSFC began the autonomously managed power system (AMPS) project. This project resulted in the assembly of a 25-kW high-voltage dc test facility and provided the means of getting man out of the loop as much as possible. AMPS includes several embedded controllers which allow a significant level of autonomous operation. More recently, the Electrical Division at MSFC has developed the space station module power management and distribution (SSM/PMAD) breadboard to investigate managing and distributing power in the Space Station Freedom habitation and laboratory modules. Again, the requirement for a high level of autonomy for the efficient operation over the lifetime of the station and for the benefits of enhanced safety has been demonstrated. This paper describes the two breadboards and the hierarchical approach to automation which was developed through these projects.

Lollar, L. F.↗
NASA NTRS1991

The propagation characteristics of the plate modes of acoustic emission waves in thin aluminum plates and thin graphite/epoxy composite plates and tubes

Acoustic emission was interpreted as modes of vibration in plates. Classical plate theory was used to predict dispersion curves for the two fundamental modes and to calculate the shapes of flexural waveforms produced by vertical step function loading. There was good agreement between theoretical and experimental results for aluminum. Composite materials required the use of a higher order plate theory (Reissner-Mindlin) to get good agreement with the measured velocities. Four composite plates with different laminate stacking sequences were studied. The dispersion curves were determined from phase spectra of the time dependent waveforms. Plate modes were shown to be useful for determining the direction of source motion. Aluminum plates were loaded by breaking a pencil lead against their surface. By machining slots at angles to the plane of a plate, the direction in which the force acted was varied. Changing the source motion direction produced regular variations in the waveforms. To demonstrate applicability beyond simple plates, waveforms produced by lead breaks on a thin walled composite tube were also shown to be interpretable as plate modes. The tube design was based on the type of struts proposed for Space Station Freedom's trussed structures.

Prosser, William H.↗
NASA NTRS1991

Optimal least-squares finite element method for elliptic problems

An optimal least squares finite element method is proposed for two dimensional and three dimensional elliptic problems and its advantages are discussed over the mixed Galerkin method and the usual least squares finite element method. In the usual least squares finite element method, the second order equation (-Delta x (Delta u) + u = f) is recast as a first order system (-Delta x p + u = f, Delta u - p = 0). The error analysis and numerical experiment show that, in this usual least squares finite element method, the rate of convergence for flux p is one order lower than optimal. In order to get an optimal least squares method, the irrotationality Delta x p = 0 should be included in the first order system.

Jiang, Bo-Nan↗
NASA NTRS1991

Development and application of virtual reality for man/systems integration

While the graphical presentation of computer models signified a quantum leap over presentations limited to text and numbers, it still has the problem of presenting an interface barrier between the human user and the computer model. The user must learn a command language in order to orient themselves in the model. For example, to move left from the current viewpoint of the model, they might be required to type 'LEFT' at a keyboard. This command is fairly intuitive, but if the viewpoint moves far enough that there are no visual cues overlapping with the first view, the user does not know if the viewpoint has moved inches, feet, or miles to the left, or perhaps remained in the same position, but rotated to the left. Until the user becomes quite familiar with the interface language of the computer model presentation, they will be proned to lossing their bearings frequently. Even a highly skilled user will occasionally get lost in the model. A new approach to presenting type type of information is to directly interpret the user's body motions as the input language for determining what view to present. When the user's head turns 45 degrees to the left, the viewpoint should be rotated 45 degrees to the left. Since the head moves through several intermediate angles between the original view and the final one, several intermediate views should be presented, providing the user with a sense of continuity between the original view and the final one. Since the primary way a human physically interacts with their environment should monitor the movements of the user's hands and alter objects in the virtual model in a way consistent with the way an actual object would move when manipulated using the same hand movements. Since this approach to the man-computer interface closely models the same type of interface that humans have with the physical world, this type of interface is often called virtual reality, and the model is referred to as a virtual world. The task of this summer fellowship was to set up a virtual reality system at MSFC and begin applying it to some of the questions which concern scientists and engineers involved in space flight. A brief discussion of this work is presented.

Brown, Marcus↗