Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Finite Volume”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Diffusion length measurement in bulk and epitaxially grown III-V semiconductors using charge collection microscopy

Diffusion lengths and surface recombination velocities were measured in GaAs diodes and InP finished solar cells. The basic technique used was charge collection microscopy, also known as electron beam induced current (EBIC). The normalized currents and distances from the pn junction were read directly from the calibrated curves obtained while using the line-scan mode in an SEM. These values were then equated to integral and infinite series expressions resulting from the solution of the diffusion equation with both extended-generation and point-generation functions. This expands previous work by examining both thin and thick samples. The surface recombination velocity was either treated as an unknown in a system of two equations or measured directly using low e(-) beam accelerating voltages. These techniques give accurate results by accounting for the effects of surface recombination and the finite size of the generation volume.

Leon, R. P.↗
NASA NTRS2002

Investigation of Venus Surface Properties

Strong localized radar echoes have been observed at decimeter wavelengths from the highlands of Venus since the earliest radar maps were obtained over 30 years ago. These echoes are some five to ten times stronger than those from the presumably basaltic rocks seen at lower altitudes elsewhere on Venus. Observations of thermal emission from the visible disk of Venus at wavelengths corresponding to those used in the radar mapping confirm that the regions of high reflectivity also exhibit low emissivity, as expected from considerations of detailed thermodynamic balance. Two possibilities have been put forward to explain this unexpected aspect of the Venus highlands: 1) surface materials of high effective dielectric constant, probably associated with finite electrical conductivity, and 2) volume scattering associated with multiple scattering from a layer of very-low-loss material containing voids and extending down a few hundred wavelengths beneath the surface. Analogs to these two mechanisms are found elsewhere in the solar system, and each is capable of explaining the basic observations. as of the early 1990's. In 1993, however, it became possible to carry out a bistatic observation of the anomalous highland regions using the Magellan spacecraft, then in orbit about Venus. In this experiment the on-board telemetry transmitter was aimed at the planet's surface with its linear S-band polarization vector oriented at 45 deg to the spacecraft-Venus-Earth scattering plane. The pointing of the transmitting antenna was adjusted so that the spacecraft-to-illuminated-surface incidence angle equalled the Earth-to-Venus-surface incidence angle. In this way, the experiment emphasized the specular scattering component. A full Stokes-Vector analysis of the reflected signal as received on Earth was carried out as the illuminated region scanned across the highland regions of Venus. From the observed position angle of the echo, it was possible to calculate the Fresnel reflectivity of a number of regions on Venus, including the high-altitude Maxwell Montes, and to show unequivocally that the complex dielectric constant of that anomalous area was 100 +/- 50i, as compared to 4.0 (real) for the typical lowland area. Thus this experiment was able to rule out definitively an hypothesis of volume scattering as the explanation for the anomalous scattering in the Venus highlands.

Ford, Peter G.↗
NASA NTRS1987

Component mode synthesis and large deflection vibration of complex structures. Volume 2: Single-mode large deflection vibrations of beams and plates using finite element method

A finite element method is presented for the large amplitude vibrations of complex structures that can be modelled with beam and rectangular plate elements subjected to harmonic excitation. Both inplane deformation and inertia are considered in the formulation. Derivation of the harmonic force and nonlinear stiffness matrices for a beam and a rectangular plate element are presented. Solution procedures and convergence characteristics of the finite element method are described. Nonlinear response to uniform and concentrated harmonic loadings and improved nonlinear free vibration results are presented for beams and rectangular plates of various boundary conditions.

Mei, Chuh↗
NASA NTRS1987

Component mode synthesis and large deflection vibration of complex structures. Volume 3: Multiple-mode nonlinear free and forced vibrations of beams using finite element method

Multiple-mode nonlinear forced vibration of a beam was analyzed by the finite element method. Inplane (longitudinal) displacement and inertia (IDI) are considered in the formulation. By combining the finite element method and nonlinear theory, more realistic models of structural response are obtained more easily and faster.

Mei, Chuh↗
NASA NTRS1989

Space Shuttle Main Engine structural analysis and data reduction/evaluation. Volume 1: Aft Skirt analysis

Using the ANSYS finite element program, a global model of the aft skirt and a detailed nonlinear model of the failure region was made. The analysis confirmed the area of failure in both STA-2B and STA-3 tests as the forging heat affected zone (HAZ) at the aft ring centerline. The highest hoop strain in the HAZ occurs in this area. However, the analysis does not predict failure as defined by ultimate elongation of the material equal to 3.5 percent total strain. The analysis correlates well with the strain gage data from both the Wyle influence test of the original design aft sjirt and the STA-3 test of the redesigned aft skirt. it is suggested that the sensitivity of the failure area material strength and stress/strain state to material properties and therefore to small manufacturing or processing variables is the most likely cause of failure below the expected material ultimate properties.

Berry, David M.↗
NASA NTRS1991

Wideband finite difference time domain implementation of surface impedance boundary conditions for good conductors

Surface impedance boundary conditions are employed to reduce the solution volume during the analysis of scattering from lossy dielectric objects. In a finite difference solution, they also can be utilized to avoid using small cells, made necessary by shorter wavelengths in conducting media, throughout the solution volume. A 1-D implementation for a surface impedance boundary condition for good conductors in the Finite Difference Time Domain (FDTD) technique.

Beggs, John H.↗
NASA NTRS1991

Wideband finite difference time domain implementation of surface impedance boundary conditions for good conductors

Surface impedance boundary conditions are used to reduce the solution volume during the analysis of scattering from lossy dielectric objects. In a finite difference solution, they also can be used to avoid using small cells, made necessary by shorter wavelengths in conducting media, throughout the solution volume. A one dimensional implementation is presented for a surface impedance boundary condition for good conductors in the Finite Difference Time Domain (FDTD) technique. In order to illustrate the FDTD surface impedance boundary condition, a planar air-lossy dielectric interface is considered.

Beggs, John H.↗
DOE OSTI2024

In situ effective pumping speed measurements as a tool for non-evaporable getter activation and saturation monitoring

We have developed method of in situ effective pumping speed measurements based on injecting finite gas pulse into a vacuum volume and subsequent recording of pressure response using a Residual Gas Analyzer (RGA). The pressure burst caused by injected gas pulse falls exponentially in time and the exponential coefficient of such pressure decay is proportional to total effective pumping speed of all vacuum pumps acting on vacuum chamber volume. The effective pumping speed can be extracted from the dependence of injected gas species pressure vs time recorded by an RGA. Non-Evaporable Getters (NEGs) are widely used in multiple ultra and extremely high vacuum devices and applications during the last several decades. Areas of NEG applications were recently expanded into vacuum devices with relatively high-pressure levels (up to 10 -7 Torr) by the invention of high capacity ZAO NEG which can be operated at elevated temperatures. The intrinsic property of all NEG-based vacuum pumps is the reduction of their pumping speed, called “NEG saturation”, after an extended period of operation. Typical time interval for such process can span from about a month and up to a few years depending on NEG type, vacuum level of NEG pump operation, and residual gas content. After that, the NEG pump will require a re-activation cycle to restore its pumping speed close to the initial value. For many applications it is difficult to realize what is the current pumping speed of NEG pump is and when the pump should be re-activated. A method for in situ effective pumping speed measurements developed in this study can be used as a tool for NEG-based pump activation and saturation monitoring. Application of such an approach to monitor pumping status of NEG pumps was utilized and will be continually used at Extended EBIS which was recently developed and commissioned for Relativistic Heavy Ion Collider (RHIC) and future Electron Ion Collider (EIC). The results obtained during commissioning are presented and discussed.

43 PARTICLE ACCELERATORS↗
DOE OSTI2020

Recovering Gardner restacking with purely diffusive operations

The maximum particle kinetic energy that can be extracted from an initial six-dimensional phase space distribution motivates the concept of free or available energy. The free energy depends on the allowed operations that can be performed. A key concept underlying the theoretical treatment of plasmas is the Gardner free energy, where the exchange of the contents of equal phase volumes is allowed. Further, a second free energy concept is the diffusive free energy, in which the contents of volumes are instead averaged. For any finite discretization of phase space, the diffusive free energy is known to be less than the Gardner free energy. However, despite the apparent fundamental differences between these free energies, it is demonstrated here that the Gardner free energy may be recovered from the continuous limit of the diffusive free energy, leading to the surprise that macroscopic phase-space conservation can be achieved by ostensibly entropy-producing microscopic operations.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

High Resolution Polar Kerr Effect Studies of CsV 3 Sb 5 : Tests for Time-Reversal Symmetry Breaking below the Charge-Order Transition

We report high resolution polar Kerr effect measurements on CsV 3 Sb 5 single crystals in search for signatures of spontaneous time reversal symmetry breaking below the charge order transition at T * = 94 K. Utilizing two different versions of zero-area loop Sagnac interferometers operating at 1550 nm wavelength, each with the fundamental attribute that without a time reversal symmetry breaking sample at its path, the interferometer is perfectly reciprocal, we find no observable Kerr effect to within the noise floor limit of the apparatus at 30 nanoradians. Simultaneous coherent reflection ratio measurements confirm the sharpness of the charge order transition in the same optical volume as the Kerr measurements. At finite magnetic field we observe a sharp onset of a diamagnetic shift in the Kerr signal at T *, which persists down to the lowest temperature without change in trend. Since 1550 nm is an energy that was shown to capture all features of the optical properties of the material that interact with the charge order transition, we are led to conclude that it is highly unlikely that time reversal symmetry is broken in the charge ordered state in CsV 3 Sb 5 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1988

Liquid sprays and flow studies in the direct-injection diesel engine under motored conditions

A two dimensional, implicit finite difference method of the control volume variety, a two equation model of turbulence, and a discrete droplet model were used to study the flow field, turbulence levels, fuel penetration, vaporization, and mixing in diesel engine environments. The model was also used to study the effects of engine speed, injection angle, spray cone angle, droplet distribution, and intake swirl angle on the flow field, spray penetration and vaporization, and turbulence in motored two-stroke diesel engines. It is shown that there are optimum conditions for injection, which depend on droplet distribution, swirl, spray cone angle, and injection angle. The optimum conditions result in good spray penetration and vaporization and in good fuel mixing. The calculation presented clearly indicates that internal combustion engine models can be used to assess, at least qualitatively, the effects of injection characteristics and engine operating conditions on the flow field and on the spray penetration and vaporization in diesel engines.

Nguyen, Hung Lee↗
NASA NTRS1991

Finite difference time domain implementation of surface impedance boundary conditions

Surface impedance boundary conditions are employed to reduce the solution volume during the analysis of scattering from lossy dielectric objects. In a finite difference solution, they also can be utilized to avoid using small cells, made necessary by shorter wavelengths in conducting media throughout the solution volume. The standard approach is to approximate the surface impedance over a very small bandwidth by its value at the center frequency, and then use that result in the boundary condition. Two implementations of the surface impedance boundary condition are presented. One implementation is a constant surface impedance boundary condition and the other is a dispersive surface impedance boundary condition that is applicable over a very large frequency bandwidth and over a large range of conductivities. Frequency domain results are presented in one dimension for two conductivity values and are compared with exact results. Scattering width results from an infinite square cylinder are presented as a 2-D demonstration. Extensions to 3-D should be straightforward.

Beggs, John H.↗
NASA NTRS1991

Finite difference time domain implementation of surface impedance boundary conditions

Surface impedance boundary conditions are employed to reduce the solution volume during the analysis of scattering from lossy dielectric objects. In the finite difference solution, they also can be utilized to avoid using small cells, made necessary by shorter wavelengths in conducting media throughout the solution volume. The standard approach is to approximate the surface impedance over a very small bandwidth by its value at the center frequency, and then use that result in the boundary condition. Here, two implementations of the surface impedance boundary condition are presented. One implementation is a constant surface impedance boundary condition and the other is a dispersive surface impedance boundary condition that is applicable over a very large frequency bandwidth and over a large range of conductivities. Frequency domain results are presented in one dimension for two conductivity values and are compared with exact results. Scattering width results from an infinite square cylinder are presented as a two dimensional demonstration. Extensions to three dimensions should be straightforward.

Beggs, John H.↗
NASA NTRS1989

Phase transformation kinetics in finite inhomogeneously nucleated systems

Phase transformation kinetics that occur by a nucleation and growth process are investigated. A simple discrete space and time model is used for the dynamics and analytical results are obtained for the volume fraction of the material transformed for both finite systems and a special example of an inhomogeneously nucleated system. The theory is developed for two cases, initial nucleation, and continuous nucleation. The results are compared with simulations of the model.

Weinberg, Michael↗
NASA NTRS1987

Surface flaw reliability analysis of ceramic components with the SCARE finite element postprocessor program

The SCARE (Structural Ceramics Analysis and Reliability Evaluation) computer program on statistical fast fracture reliability analysis with quadratic elements for volume distributed imperfections is enhanced to include the use of linear finite elements and the capability of designing against concurrent surface flaw induced ceramic component failure. The SCARE code is presently coupled as a postprocessor to the MSC/NASTRAN general purpose, finite element analysis program. The improved version now includes the Weibull and Batdorf statistical failure theories for both surface and volume flaw based reliability analysis. The program uses the two-parameter Weibull fracture strength cumulative failure probability distribution model with the principle of independent action for poly-axial stress states, and Batdorf's shear-sensitive as well as shear-insensitive statistical theories. The shear-sensitive surface crack configurations include the Griffith crack and Griffith notch geometries, using the total critical coplanar strain energy release rate criterion to predict mixed-mode fracture. Weibull material parameters based on both surface and volume flaw induced fracture can also be calculated from modulus of rupture bar tests, using the least squares method with known specimen geometry and grouped fracture data. The statistical fast fracture theories for surface flaw induced failure, along with selected input and output formats and options, are summarized. An example problem to demonstrate various features of the program is included.

Gyekenyesi, John P.↗