Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Feedback Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92

Fabrication and test of a variable conductance heat pipe

A variable conductance heat pipe (VCHP) with feedback control was fabricated with a reservoir-condenser volume ratio of 10 and an axially grooved action section. Tests of the heat transport capability were greater than or equal to the analytical predictions for the no gas case. When gas was added, the pipe performance degraded by 18% at zero tilt as was expected. The placement of the reservoir heater and the test fixture cooling fins are believed to have caused a superheated vapor condition in the reservoir. Erroneously high reservoir temperature indications resulted from this condition. The observed temperature gradients in the reservoir lend support to this theory. The net result was higher than predicted reservoir temperatures. Also, significant increases in minimum heat load resulted for controller set point temperatures higher than 0 C. At 30 C, control within the tolerance band was maintained, but high reservoir heater power was required. Analyses showed that control is not possible for reasonably low reservoir heater power. This is supported by the observation of a significant reservoir heat leak through the condenser.

Lehtinen, A. M.↗

AAA gunnermodel based on observer theory

The Luenberger observer theory is used to develop a predictive model of a gunner's tracking response in antiaircraft artillery systems. This model is composed of an observer, a feedback controller and a remnant element. An important feature of the model is that the structure is simple, hence a computer simulation requires only a short execution time. A parameter identification program based on the least squares curve fitting method and the Gauss Newton gradient algorithm is developed to determine the parameter values of the gunner model. Thus, a systematic procedure exists for identifying model parameters for a given antiaircraft tracking task. Model predictions of tracking errors are compared with human tracking data obtained from manned simulation experiments. Model predictions are in excellent agreement with the empirical data for several flyby and maneuvering target trajectories.

Kou, R. S.↗

LSA Large Area Silicon Sheet Task Continuous Liquid Feed Czochralski Growth

A process for the continuous growth of crystals by the Czochralski method, suitable for producing single silicon crystals for use in solar cells was studied. Continuous growth is the growth of 100 Kg of single silicon crystals, 10 cm in diameter, from one container. A furnace with continuous liquid replenishment of the growth crucible, accomplished by a melt-down system and a liquid transfer mechanism, with associated automatic feedback controls was developed. Elements of the transfer system were further developed and tested during actual transfer runs. Considerable simplification of the heating element of the transfer tube was achieved. Accuracy and reliability of the temperature sensor, which is part of the power input control system for the transfer tube, was improved. Electrical and thermal effectiveness were increased while assembly of the transfer tube system was further simplified.

Fiegl, G.↗

LSA Large Area Silicon Sheet Task. Continuous Liquid Feed Czochralski Growth

The design and development of equipment and processes to demonstrate continuous growth of crystals by the Czochralski method suitable for producing single silicon crystals for use in solar cells is presented. The growth of at least 150 kg of mono silicon crystal, 150 mm in diameter is continuous from one growth container. A furnace with continuous liquid replenishment of the growth crucible, accomplished by a meltdown system with a continuous solid silicon feed mechanism and a liquid transfer system, with associated automatic feedback controls is discussed. Due to the silicon monoxide build up in the furnace and its retarding effect on crystal growth the furnace conversion for operation in the low pressure range is described. Development of systems for continuous solid recharging of the meltdown chamber for various forms of poly silicon is described.

Fiegl, G.↗

Application of singular perturbation techniques /SPT/ and continuation methods for on-line aircraft trajectory optimization

The singular perturbation theory (SPT) approximation of optimal feedback control laws is presented and methods for on-line application of these approximations are discussed. It is demonstrated that SPT control laws break down when the current state is near the terminal target state. The use of continuation methods to improve the accuracy of the SPT approximation and to obtain global solutions of two-point boundary value problems is also discussed. As an illustration, consideration is given to the minimum-time control of a supersonic aircraft for a three-dimensional intercept problem.

Washburn, R. B.↗

An approximation for inverse Laplace transforms

Programmable calculator runs simple finite-series approximation for Laplace transform inversions. Utilizing family of orthonormal functions, approximation is used for wide range of transforms, including those encountered in feedback control problems. Method works well as long as F(t) decays to zero as it approaches infinity and so is appliable to most physical systems.

Lear, W. M.↗

A pilot modeling technique for handling-qualities research

A brief survey of the more dominant analysis techniques used in closed-loop handling-qualities research is presented. These techniques are shown to rely on so-called classical and modern analytical models of the human pilot which have their foundation in the analysis and design principles of feedback control. The optimal control model of the human pilot is discussed in some detail and a novel approach to the a priori selection of pertinent model parameters is discussed. Frequency domain and tracking performance data from 10 pilot-in-the-loop simulation experiments involving 3 different tasks are used to demonstrate the parameter selection technique. Finally, the utility of this modeling approach in handling-qualities research is discussed.

Hess, R. A.↗

Flashlamp Driver for Quasi-CW Laser Pumping

Circuit maintains constant high-current level through lamp while lighted and a low simmer current through lamp while not lighted. Lamp current is switched between these two modes by transistor; transistor is therefore called current-mode switch. Stable light pulses are emitted from flashlamp when monostable multivibrator goes high, in part because unsaturated transistor switch has negative feedback control that keeps lamp current constant.

Logan, K. E.↗

Sensor/actuator failure detection for turbofan engines

A procedure for sensor/actuator failure detection using a generalized likelihood ratio (GLR) test is described. The GLR concept can provide a reliable evaluation of failure occurence when associated with a feedback control design which does not require sensor outputs to provide data estimates. A GLR detector was developed and tested.

Behbehani, K.↗

UAH/NASA Workshop on The Uses of a Tethered Satellite System

Potential applications of the system are categorized into four areas: geological applications, atmospheric applications, electrodynamics and plasma studies, and technology applications. The multiple-use tethered system with feedback control, will be capable of supporting a payload or satellite suspended from the Shuttle cargo bay, at distances up to 100 kilometers from the Shuttle. Experiments proposed include: geomagnetic mapping, lower atmospheric measurements, ionospheric interactions with large space structures, solar wind transport, and magnetohydrodynamic measurements.

Wu, S. T.↗

Dynamic profile of a prototype pivoted proof-mass actuator

A prototype of a linear inertial reaction actuation (damper) device employing a flexure-pivoted reaction (proof) mass is discussed. The mass is driven by an electromechanic motor using a dc electromagnetic field and an ac electromagnetic drive. During the damping process, the actuator dissipates structural kinetic energy as heat through electromagnetic damping. A model of the inertial, stiffness and damping properties is presented along with the characteristic differential equations describing the coupled response of the actuator and structure. The equations, employing the dynamic coefficients, are oriented in the form of a feedback control network in which distributed sensors are used to dictate actuator response leading to a specified amount of structural excitation or damping.

Miller, D. W.↗

Experimental and analytical studies of advanced air cushion landing systems

Several concepts are developed for air cushion landing systems (ACLS) which have the potential for improving performance characteristics (roll stiffness, heave damping, and trunk flutter), and reducing fabrication cost and complexity. After an initial screening, the following five concepts were evaluated in detail: damped trunk, filled trunk, compartmented trunk, segmented trunk, and roll feedback control. The evaluation was based on tests performed on scale models. An ACLS dynamic simulation developed earlier is updated so that it can be used to predict the performance of full-scale ACLS incorporating these refinements. The simulation was validated through scale-model tests. A full-scale ACLS based on the segmented trunk concept was fabricated and installed on the NASA ACLS test vehicle, where it is used to support advanced system development. A geometrically-scaled model (one third full scale) of the NASA test vehicle was fabricated and tested. This model, evaluated by means of a series of static and dynamic tests, is used to investigate scaling relationships between reduced and full-scale models. The analytical model developed earlier is applied to simulate both the one third scale and the full scale response.

Lee, E. G. S.↗

Influence of maneuverability on helicopter combat effectiveness

A computational procedure employing a stochastic learning method in conjunction with dynamic simulation of helicopter flight and weapon system operation was used to derive helicopter maneuvering strategies. The derived strategies maximize either survival or kill probability and are in the form of a feedback control based upon threat visual or warning system cues. Maneuverability parameters implicit in the strategy development include maximum longitudinal acceleration and deceleration, maximum sustained and transient load factor turn rate at forward speed, and maximum pedal turn rate and lateral acceleration at hover. Results are presented in terms of probability of skill for all combat initial conditions for two threat categories.

Falco, M.↗

Development of a helicopter rotor/propulsion system dynamics analysis

A time-domain analysis of coupled engine/drive train/rotor dynamics of a twin-engine, single main rotor helicopter model has been performed. The analysis incorporates an existing helicopter model with nonlinear simulations of a helicopter turboshaft engine and its fuel controller. System dynamic behavior is studied using the resulting simulation which included representations for the two engines and their fuel controllers, drive system, main rotor, tail rotor, and aircraft rigid body motions. Time histories of engine and rotor RPM response to pilot control inputs are studied for a baseline rotor and propulsion system model. Sensitivity of rotor RPM droop to fuel controller gain changes and collective input feed-forward gain changes are studied. Torque-load-sharing between the two engines is investigated by making changes in the fuel controller feedback paths. A linear engine model is derived from the nonlinear engine simulation and used in the coupled system analysis. This four-state linear engine model is then reduced to a three-state model. The effect of this simplification on coupled system behavior is shown.

Warmbrodt, W.↗

Passive Magnetic Bearing

Magnetic bearing for limited rotation devices requires no feedback control system to sense and correct shaft position. Passive Magnetic Torsion Bearing requires no power supply and has no rubbing parts. Torsion wire restrains against axial instability. Magnetic flux geometry chosen to assure lateral stability with radial restoring force that maintains alignment.

Studer, P. A.↗

Phase Modulation Stops Levitated Sample Rotation

Rotation of sample in acoustic levitator prevented by relatively simple phase-modulation scheme. Technique differs from older methods; no feedback control or observation of sample required, nor necessary to carefully tune or detune two oscillators to precise frequency differences from resonance.

Barmatz, M. B.↗

The linear regulator problem for parabolic systems

An approximation framework is presented for computation (in finite imensional spaces) of Riccati operators that can be guaranteed to converge to the Riccati operator in feedback controls for abstract evolution systems in a Hilbert space. It is shown how these results may be used in the linear optimal regulator problem for a large class of parabolic systems.

Banks, H. T.↗

A closed-loop principal component analysis of a tetrahedral truss

A tetrahedral truss, representative of a fairly broad class of large space structures, is considered. A method, measuring the dynamical importance of each elastic mode when the structure is under feedback control, is presented. The main conclusion is that the closed-loop importance of each vibration mode depends on the robustness requirements. Also, there appears to be a conflict between precise control of a given node of the structure and stability margin, these two requirements leading to contradictory classifications of the modes by order of importance.

Jonckheere, E. A.↗