Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLOW MODELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Evaluation of a Commercial Surface Vorticity Flow Solver for the Modeling of Propeller-Wing Interaction

A commercially available surface vorticity flow solver’s ability to model propeller-wing interaction effects was evaluated. First, a study was conducted to determine solution sensitivity to simulation parameters. Then, a deflected slipstream experiment was replicated with an actuator disk and wing model. Comparison with experimental data showed that predictions of lift and longitudinal force coefficients matched well at low flap deflections, but experienced offsets in magnitude with increasing flap deflection. Predictions of pitching moment differed significantly from experimental data largely due to the simple actuator disk model being insufficient for capturing the effects of non-zero flow incidence and non-uniform inflow.

Fei, Xiaofan↗
NASA NTRS1991

Overview of aerothermodynamic loads definition study

The objective of the Aerothermodynamic Loads Definition Study is to develop methods of accurately predicting the operating environment in advanced Earth-to-Orbit (ETO) propulsion systems, such as the Space Shuttle Main Engine (SSME) powerhead. Development of time averaged and time dependent three dimensional viscous computer codes as well as experimental verification and engine diagnostic testing are considered to be essential in achieving that objective. Time-averaged, nonsteady, and transient operating loads must all be well defined in order to accurately predict powerhead life. Described here is work in unsteady heat flow analysis, improved modeling of preburner flow, turbulence modeling for turbomachinery, computation of three dimensional flow with heat transfer, and unsteady viscous multi-blade row turbine analysis.

Gaugler, Raymond E.↗
NASA NTRS1991

Second-order closure models for supersonic turbulent flows

Recent work on the development of a second-order closure model for high-speed compressible flows is reviewed. This turbulent closure is based on the solution of modeled transport equations for the Favre-averaged Reynolds stress tensor and the solenoidal part of the turbulent dissipation rate. A new model for the compressible dissipation is used along with traditional gradient transport models for the Reynolds heat flux and mass flux terms. Consistent with simple asymptotic analyses, the deviatoric part of the remaining higher-order correlations in the Reynolds stress transport equations are modeled by a variable density extension of the newest incompressible models. The resulting second-order closure model is tested in a variety of compressible turbulent flows which include the decay of isotropic turbulence, homogeneous shear flow, the supersonic mixing layer, and the supersonic flat-plate turbulent boundary layer. Comparisons between the model predictions and the results of physical and numerical experiments are quite encouraging.

Speziale, Charles G.↗
NASA NTRS1993

Two-dimensional CFD modeling of wave rotor flow dynamics

A two-dimensional Navier-Stokes solver developed for detailed study of wave rotor flow dynamics is described. The CFD model is helping characterize important loss mechanisms within the wave rotor. The wave rotor stationary ports and the moving rotor passages are resolved on multiple computational grid blocks. The finite-volume form of the thin-layer Navier-Stokes equations with laminar viscosity are integrated in time using a four-stage Runge-Kutta scheme. The Roe approximate Riemann solution scheme or the computationally less expensive Advection Upstream Splitting Method (AUSM) flux-splitting scheme are used to effect upwind-differencing of the inviscid flux terms, using cell interface primitive variables set by MUSCL-type interpolation. The diffusion terms are central-differenced. The solver is validated using a steady shock/laminar boundary layer interaction problem and an unsteady, inviscid wave rotor passage gradual opening problem. A model inlet port/passage charging problem is simulated and key features of the unsteady wave rotor flow field are identified. Lastly, the medium pressure inlet port and high pressure outlet port portion of the NASA Lewis Research Center experimental divider cycle is simulated and computed results are compared with experimental measurements. The model accurately predicts the wave timing within the rotor passage and the distribution of flow variables in the stationary inlet port region.

Welch, Gerard E.↗
NASA NTRS1994

Two-dimensional CFD modeling of wave rotor flow dynamics

A two-dimensional Navier-Stokes solver developed for detailed study of wave rotor flow dynamics is described. The CFD model is helping characterize important loss mechanisms within the wave rotor. The wave rotor stationary ports and the moving rotor passages are resolved on multiple computational grid blocks. The finite-volume form of the thin-layer Navier-Stokes equations with laminar viscosity are integrated in time using a four-stage Runge-Kutta scheme. Roe's approximate Riemann solution scheme or the computationally less expensive advection upstream splitting method (AUSM) flux-splitting scheme is used to effect upwind-differencing of the inviscid flux terms, using cell interface primitive variables set by MUSCL-type interpolation. The diffusion terms are central-differenced. The solver is validated using a steady shock/laminar boundary layer interaction problem and an unsteady, inviscid wave rotor passage gradual opening problem. A model inlet port/passage charging problem is simulated and key features of the unsteady wave rotor flow field are identified. Lastly, the medium pressure inlet port and high pressure outlet port portion of the NASA Lewis Research Center experimental divider cycle is simulated and computed results are compared with experimental measurements. The model accurately predicts the wave timing within the rotor passages and the distribution of flow variables in the stationary inlet port region.

Welch, Gerard E.↗
DOE OSTI2023

ENSO-Induced Teleconnection: Process-Oriented Diagnostics to Assess Rossby Wave Sources and Ambient Flow Properties in Climate Models

Climate model fidelity in representing ENSO-induced teleconnection is assessed with process-oriented diagnostics that examine a chain of processes, from equatorial Pacific precipitation to the midlatitude circulation pattern over the Pacific–North American regions. Such processes are rarely addressed during model development. Using an upper-tropospheric divergent level, local vorticity gradient of the ambient zonal flow (∂ 2 U¯/∂y 2 ) and a restoring force for Rossby waves (β * ) are estimated, the equivalent barotropic vorticity equation is solved, and an anomalous Rossby wave source (RWS') quantified. The analysis is applied to AMIP5 and AMIP6 simulations. For a realistic circulation response representation, the hypothesis that models accurately represent the strength and location of RWS', and spatial variations in β * is tested. Compared to AMIP5, in AMIP6 there are clear improvements in representing RWS' and β * . To validate the hypothesis, the analysis identifies two metrics: spatially coherent RWS' in the subtropical North Pacific, and longitudes of negative β * over the western-central North Pacific. By projecting these metrics in two and three-dimensional views, improvements or degradations in model versions are apparent. If a model’s fidelity in representing ∂ 2 U¯/∂y 2 and RWS' are compromised, then radiated Rossby waves are reflected more equatorward, resulting in zonally elongated circulation anomalies over the central North Pacific. Thus, during climate model development, applying this analysis frequently will keep a regular check on the fidelity of the modeled response to anomalous El Niño convection in conjunction with changing model ambient flow dependencies. As a result, this analysis is intended to form a process-oriented diagnostics package, a community contribution to the NOAA Model Diagnostics Task Force.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1990

Control-oriented modeling of combustion and flow processes in liquid propellant rocket engines

This paper presents a control-oriented model of the flow, reaction, and transport processes in liquid propellant rocket combustion chambers, based on the multicomponent conservation laws of gas dynamics. This model provides a framework for the inclusion of detailed chemical kinetic relations, viscous and other dissipative effects, a variety of actuators and sensors, as well as process and measurement disturbances. In addition to its potential usefulness to the designer in understanding the dynamical complexity of the system and the sources of model uncertainty, the model provides a rigorous basis for control system design. An appraisal of current and feasible actuators and sensors, and their mathematical representation are included.

Bentsman, Joseph↗
NASA NTRS2016

Application of a Full Reynolds Stress Model to High Lift Flows

A recently developed second-moment Reynolds stress model was applied to two challenging high-lift flows: (1) transonic flow over the ONERA M6 wing, and (2) subsonic flow over the DLR-F11 wing-body configuration from the second AIAA High Lift Prediction Workshop. In this study, the Reynolds stress model results were contrasted with those obtained from one- and two{equation turbulence models, and were found to be competitive in terms of the prediction of shock location and separation. For an ONERA M6 case, results from multiple codes, grids, and models were compared, with the Reynolds stress model tending to yield a slightly smaller shock-induced separation bubble near the wing tip than the simpler models, but all models were fairly close to the limited experimental surface pressure data. For a series of high-lift DLR{F11 cases, the range of results was more limited, but there was indication that the Reynolds stress model yielded less-separated results than the one-equation model near maximum lift. These less-separated results were similar to results from the one-equation model with a quadratic constitutive relation. Additional computations need to be performed before a more definitive assessment of the Reynolds stress model can be made.

Lee-Rausch, E. M.↗
NASA NTRS1982

Surface tension driven flow in glass melts and model fluids

Surface tension driven flow has been investigated analytically and experimentally using an apparatus where a free column of molten glass or model fluids was supported at its top and bottom faces by solid surfaces. The glass used in the experiments was sodium diborate, and the model fluids were silicone oils. In both the model fluid and glass melt experiments, conclusive evidence was obtained to prove that the observed flow was driven primarily by surface tension forces. The experimental observations are in qualitative agreement with predictions from the theoretical model.

Mcneil, T. J.↗
NASA NTRS1998

Flow Simulation in Secondary Flow Passages of a Rocket Engine Turbopump

This paper presents application of a Generalized Fluid System Simulation Program (GFSSP) to model fluid flow in a very complex secondary flow circuit of a rocket engine turbopump, SIMPLEX. SIMPLEX was a low cost turbopump designed, manufactured and tested to demonstrate the ability to reduce the overall cost and design cycle time of turbomachinery. GFSSP is a general purpose computer program for analyzing flowrate, pressure, temperature and concentration distribution in a complex flow network. The program employs a finite volume formulation of mass, momentum and energy conservation equations in conjunction with thermodynamic equation of state of a real fluid. The secondary flow passages modeled include flow between the impeller shroud and housing, impeller back face and housing, flow through labyrinth seal and bearing, return line flow to inducer and flow adjacent to front and back face of the turbine. Axial load on the bearing are calculated from the predicted pressure on all axial faces of the rotor. The predicted pressure and temperature distributions compared well with the test data.

Schallhorn, Paul↗
DOE OSTI2026

Audible Noise Modeling of Hydrogen Release Sonic Hazards in Rail Maintenance Facilities

This study implemented validated literature models to predict audible noise due to pressurized gaseous hydrogen releases through a thermally-activated pressure relief device (TPRD) and attached vent stack. A literature survey discovered limited hydrogen-specific noise prediction models validated by experiments. However, empirical noise prediction models for air flowing through pipes and valves were identified. These empirical models were used to predict noise levels and compared against hydrogen noise data reported in two studies: one experimental study of noise from hydrogen leaking through a pipe and another which modeled hydrogen flowing through a solenoid valve during a fuel cell vehicle refueling. The valve flow model was then applied to predict noise for hydrogen releases through a TPRD. Results show that hydrogen releases through a TPRD can produce harmful noise levels varying from 134 to 150 dB. However, further model validation and additional experimental data are needed to improve prediction confidence and accuracy.

08 HYDROGEN↗
NASA NTRSDate not supplied

Wall-modeled LES of Turbulent Flow Over a Two-dimensional Gaussian Bump

We perform wall-modeled large eddy simulations (WMLES) of turbulent flow over a nominally two-dimensional Gaussian-shaped bump geometry to assess its performance in the accelerating and separation regions of the flow. The flow conditions are based on high-fidelity numerical simulation of Uzun & Malik (AIAA Journal 2022). The oncoming flow Mach number is 0.2, with the bump length-based Reynolds number (ReL) of 2 million. In our previous study, while WMLES with the constant coefficient Vreman subgrid scale model and equilibrium wall model performed satisfactorily at lower ReL = 1 million, it failed to predict flow separation at the higher Re, contrary to the experimental observations. We investigate the sensitivity of WMLES to different subgrid scale models, wall models, and grid resolution and topology on flow separation by comparing with available data.

Computational Fluid Dynamics↗
DOE OSTI2023

SPH modeling of biomass granular flow: Theoretical implementation and experimental validation

The commercialization of biomass-derived energy is impeded by flowability challenges arising from the feeding and handling of granular biomass materials in full-scale biorefineries. To overcome these obstacles, a robust and accurate model to simulate the flow of granular biomass is indispensable. However, conventional mesh-based numerical codes are limited by inherent mesh distortion in simulating large deformation that commonly occurs in granular biomass handling. Here, in this study, we propose a graphics processing unit (GPU)-accelerated meshless Smoothed Particle Hydrodynamics (SPH) code to model the flow of granular biomass materials. A modified void ratio-based mass conversation, a hybrid particle-to-particle/surface frictional boundary treatment, and a hypoplastic constitutive model are implemented. Four numerical examples, an elastic block sliding on inclined planes, sand column collapse, Angle of Repose, and axial compression tests for pine chips, were simulated using the developed SPH code. The results demonstrate good agreement between numerical predictions and analytical and experimental data for all four examples, validating the SPH code and increasing confidence that it can be applied to simulate more complex granular biomass handling processes, such as hopper feeding or auger conveyance.

09 BIOMASS FUELS↗
NASA NTRS1991

A near-wall two-equation model for compressible turbulent flows

A near-wall two-equation turbulence model of the K - epsilon type is developed for the description of high-speed compressible flows. The Favre-averaged equations of motion are solved in conjunction with modeled transport equations for the turbulent kinetic energy and solenoidal dissipation wherein a variable density extension of the asymptotically consistent near-wall model of So and co-workers is supplemented with new dilatational models. The resulting compressible two-equation model is tested in the supersonic flat plate boundary layer - with an adiabatic wall and with wall cooling - for Mach numbers as large as 10. Direct comparisons of the predictions of the new model with raw experimental data and with results from the K - omega model indicate that it performs well for a wide range of Mach numbers. The surprising finding is that the Morkovin hypothesis, where turbulent dilatational terms are neglected, works well at high Mach numbers, provided that the near wall model is asymptotically consistent. Instances where the model predictions deviate from the experiments appear to be attributable to the assumption of constant turbulent Prandtl number - a deficiency that will be addressed in a future paper.

Zhang, H. S.↗
NASA NTRS1992

End-to-end modelling of He II flow systems

A practical computer code has been developed which uses the accepted two-fluid model to simulate He II flow in complicated systems. The full set of equations are used, retaining the coupling between the pressure, temperature and velocity fields. This permits modeling He II flow over the full range of conditions, from strongly or weakly driven flow through large pipes, narrow channels and porous media. The system may include most of the components used in modern superfluid flow systems: non-ideal thermomechanical pumps, tapered sections, constrictions, lines with heated side walls and heat exchangers. The model is validated by comparison with published experimental data. It is applied to a complex system to show some of the non-intuitive feedback effects that can occur. This code is ready to be used as a design tool for practical applications of He II. It can also be used for the design of He II experiments and as a tool for comparison of experimental data with the standard two-fluid model.

Mord, A. J.↗
DOE OSTI2021

Mixing Cell Model: A One-Dimensional Numerical Model for Assessment of Water Flow and Contaminant Transport in the Unsaturated Zone

This report describes the Mixing Cell Model code, a one dimensional model for water flow and solute transport in the unsaturated zone under steady state or transient flow conditions. The model is based on the principles and assumptions underlying mixing-cell model formulations. The unsaturated zone is discretized into a series of independent mixing cells. Each cell may have unique hydrologic, lithologic, and sorptive properties. Ordinary differential equations describe the material (water and solute) balance within each cell. Water-flow equations are derived from the continuity equation, assuming that unit gradient conditions exist at all times in each cell. Pressure gradients are considered implicitly through model discretization. Unsaturated hydraulic conductivity and moisture contents are determined by the material specific moisture-characteristic curves. Solute-transport processes include explicit treatment of advective processes, first order chain decay, and linear sorption reactions. Dispersion is addressed through implicit and explicit dispersion. Implicit dispersion is an inherent feature of all mixing-cell models and originates from the formulation of the problem in terms of mass balance around fully mixed volume elements. Expressions are provided that relate implicit dispersion to the physical dispersion of the system. Two FORTRAN codes were developed to solve the water flow and solute-transport equations: (1) the Mixing Cell Model for Flow (MCMF) solves transient water-flow problems and (2) the Mixing Cell Model for Transport (MCMT) solves the solute-transport problem. The transient water-flow problem is typically solved first by estimating the water flux through each cell in the model domain as a function of time using the MCMF code. These data are stored in either ASCII or binary files that are later read by the solute transport code (MCMT). Code output includes solute pore water concentrations, water and solute inventories in each cell and at each specified output time, and water and solute fluxes through each cell and specified output time. Computer run times for coupled transient water flow and solute transport were typically several seconds on a 2 GHz Intel Pentium IV desktop computer. The model was benchmarked against analytical solutions and finite element approximations to the partial differential equations (PDE) describing unsaturated flow and transport. Differences between the maximum solute flux estimated by the mixing cell model and the PDE models were typically less than two percent. This revision includes an option for a fixed concentration lower boundary condition for diffusive fluxes for versions 020321 and later.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1983

Evaporation and combustion of sprays

A description is provided of recent spray evaporation and combustion models, taking into account turbulent two- and three-dimensional spray processes found in furnaces, gas turbine combustors, and internal combustion engines. Within the class of spray models of interest, two major categories are distinguished, including locally homogeneous flow (LHF) models and separated flow (SF) models. SF models are of the greatest practical importance, but LHF models have distinct advantages in some cases. Attention is also given to recent progress on modeling interactions between drops and the flow in both dilute and dense sprays, involving sprays having low and high liquid volume fractions, respectively.

Faeth, G. M.↗
NASA NTRS1992

A near-wall two-equation model for compressible turbulent flows

A near-wall two-equation turbulence model of the k-epsilon type is developed for the description of high-speed compressible flows. The Favre-averaged equations of motion are solved in conjunction with modeled transport equations for the turbulent kinetic energy and solenoidal dissipation wherein a variable density extension of the asymptotically consistent near-wall model of So and co-workers is supplemented with new dilatational models. The resulting compressible two-equation model is tested in the supersonic flat plate boundary layer - with an adiabatic wall and with wall cooling - for Mach numbers as large as 10. Direct comparisons of the predictions of the new model with raw experimental data and with results from the K-omega model indicate that it performs well for a wide range of Mach numbers. The surprising finding is that the Morkovin hypothesis, where turbulent dilatational terms are neglected, works well at high Mach numbers, provided that the near wall model is asymptotically consistent. Instances where the model predictions deviate from the experiments appear to be attributable to the assumption of constant turbulent Prandtl number - a deficiency that will be addressed in a future paper.

Zhang, H. S.↗