Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FABRICATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Fabrication and Sub-Assembly of Electrostatically Actuated Silicon Nitride Microshutter Arrays

We have developed a new microshutter array (MSA) subassembly. The MSA and a silicon substrate are flip-bonded together. The MSA has a new back side fabrication process to actuate the microshutters electrostatically, and the new silicon substrate has light shields. The microshutters with a pixel size of 100 x 200 sq micrometers are fabricated on silicon with thin silicon nitride membranes. The microshutters rotate 90 deg on torsion bars. The selected microshutters are actuated, held, and addressed electrostatically by applying voltages on the electrodes the front and back sides of the microshutters. The substrate has the light shield to block lights around the microshutters. Also, electrical connections are made from the MSA to a controller board via the substrate.

microshutter array (MSA) sub-assembly↗
NASA NTRS2018

Systems and Methods for Designing and Fabricating Support Structures for Overhang Geometries of Parts in Additive Manufacturing

Systems and methods are provided for designing and fabricating contact-free support structures for overhang geometries of parts fabricated using electron beam additive manufacturing. One or more layers of un-melted metallic powder are disposed in an elongate gap between an upper horizontal surface of the support structure and a lower surface of the overhang geometry. The powder conducts heat from the overhang geometry to the support structure. The support structure acts as a heat sink to enhance heat transfer and reduce the temperature and severe thermal gradients due to poor thermal conductivity of metallic powders underneath the overhang. Because the support structure is minimally or not connected to the part, the support structure can be removed with minimal or no post-processing step.

Chou, Yuag-Shan↗
NASA NTRS2018

Design, Fabrication, and Critical Current Testing of No-Insulation Superconducting Rotor Coils for NASA's 1.4 MW High-Efficiency Megawatt Motor

NASA Glenn Research Center is developing a 1.4 MW high-efficiency electric machine for future electrified aircraft to reduce energy consumption, emissions, and noise. This wound-field, synchronous machine employs a self-cooled, superconducting rotor to achieve excellent specific power and efficiency. This paper discusses the design and fabrication of the no-insulation high temperature superconducting (HTS) rotor coils and compares them to conventionally insulated HTS coils. Two sub-scale test coils with epoxy on only one axial face were fabricated. Critical current testing of the coils at 77 K and self field was conducted to study the influence of thermal cycling on their critical current and n-value. After two or four aggressive thermal cycles between 77 K and about 278 K (5 degree C), the critical current and n-value were nearly unchanged, indicating very little to no degradation.

electric aircraft propulsion↗
NASA NTRS2018

Building a Plastics Fabrication Laboratory on the ISS: FabLab, MANTIS, Refabricator, CRISSP, ERASMUS, and MAMBA

The objective of NASA's In Space Manufacturing program is to develop manufacturing technologies and processes necessary to provide "on-demand, sustainable operations for exploration missions." Using the ISS as a test bed, in 2014, NASA installed and successfully tested a 3D printer for in-space operations, demonstrating the 3D printing process as well as sending digital files for printing from earth to the printer. The success of this technology demonstration has shown that on-orbit manufacturing technologies can be used to limit the earth reliance for cis-lunar missions. Because of this success, numerous opportunities have been provided by NASA to further in-space manufacturing by focusing on the development of highly autonomous manufacturing systems, recycling technologies, and robotics with the ultimate goal of building a fabrication laboratory now within reach. From technologies developed for ISS activities and demonstration missions, Tethers Unlimited, Inc. (TUI) is building a Plastics Manufacturing Laboratory capable of fabricating parts on-demand and as-needed while recycling waste plastics with minimal human interaction required. Parts will be manufactured through additive manufacturing. Precision machining will ensure manufactured parts are in tolerance with the end-use requirements. Recycling waste plastics will enable both waste from the crew and waste from processing to be re-processed into something new. In addition, these manufacturing and recycling technologies are supported by part verification/validation technique and robotic servicing, minimizing human interaction with the system and eventually enabling unmanned off-world manufacturing.

Muhlbauer, Rachel↗
NASA NTRS2018

NASA's In-Space Manufacturing Project: Toward a Multimaterial Fabrication Laboratory for the International Space Station

uman space exploration to date has been limited to low Earth orbit and the moon. The International Space Station (ISS) provides a unique opportunity for NASA to partner with private industry for development and demonstration of the technologies needed to support exploration initiatives. One challenge that is critical to sustainable and safer exploration is the ability to manufacture and recycle materials in space. This paper provides an overview of NASA's in-space manufacturing (ISM) project, its past and current activities, and how technologies under development will ultimately culminate in a multimaterial fabrication laboratory ("ISM FabLab") to be deployed on the International Space Station in the early 2020s. ISM is a critical capability for the long endurance missions NASA seeks to undertake in the coming decades. An unanticipated failure that can be adapted for in low earth orbit, through a resupply launch or a return to earth, may instead result in a loss of mission while in transit to Mars. To have a suite of functional ISM capabilities that are compatible with NASA's exploration timeline, ISM must be equipped with the resources necessary to develop these technologies and deploy them for testing prior to the scheduled de-orbit of ISS in 2024. The paper provides a broad overview of ISM projects activities culminating with the Fabrication Laboratory for ISS. The FabLab will move NASA and private industry significantly closer to changing historical paradigms for human spaceflight where all materials used in space are launched from earth. While the current ISM FabLab will be tested on ISS, future systems are eventually intended for use in a deep space habitat or transit vehicle. The work of commercial companies funded under NASA's Small Business Innovative Research Program (SBIR) is also discussed, as these activities, from development of recyclable packaging for ISS to additive manufacturing capabilities for metals and electronics, could also potentially be infused into FabLab exploration capabilities as well.

Prater, Tracie↗
NASA NTRS2018

Design, Fabrication, and Critical Current Testing of No-Insulation Superconducting Rotor Coils for NASA's High-Efficiency Megawatt Motor

NASA Glenn Research Center is developing a 1.4~MW high-efficiency electric machine for future electrified aircraft to reduce energy consumption, emissions, and noise. This wound-field, synchronous machine employs a self-cooled, superconducting rotor to achieve excellent specific power and efficiency. This paper discusses the fabrication of the no-insulation high temperature superconducting (HTS) coils and presents the lessons learned. The process is compared to the fabrication of conventionally insulated HTS coils. Testing of the coils' critical current at liquid nitrogen temperature is also presented. The influence of thermal cycling on the critical current and n-value is studied.

Scheidler, Justin J.↗
NASA NTRS2018

Polymer Matrix Composites Fabrication and Testing

This project involves two separate processes for fabricating carbon fiber composite parts using Hexcel’s RTM6 resin system and Kaneka’s IR-6070 toughened resin system to impregnate carbon fiber tow and weave. These two resins were chosen to model microcracking in parts using RTM6 compared to parts using IR-6070. Plies of the composites were made by painting resin onto 8 harness satin weave or impregnating IM7 12k tow in a prepregging machine. Plies were consolidated using an out-of-autoclave oven or a heat press. Fabrication of the composite parts were conducted with the end goal of sending the composites to be tested and modeled for microcracking. The data will be used for computer modeling in the future.

Miller, Sandi↗
NASA NTRS2019

Lessons Learned in Fabrication of a High-Specific-Torque Concentric Magnetic Gear

Magnetic gearing is being investigated at NASA as a replacement to conventional mechanical gearing in aerospace applications. Some key benefits of magnetic gears over mechanical gearing are torque transmission without mechanical contact, decreased transmission noise, less frequent maintenance, and lack of lubrication. In order to take advantage of these benefits in aerospace applications, magnetic gearing must be shown to provide high enough specific torque (torque per unit mass). Prototype 2 (PT-2), developed to maximize specific torque, and fabricated at NASA Glenn Research Center, has shown promising specific torque comparable to low torque mechanical gears. This work will briefly review the electromagnetic and structural design of PT-2, provide detailed information on fabrication and assembly, examine build errors, walk through rebuild efforts to improve operation, and conclude with remarks on build difficulties and opportunities for improvement in future prototypes.

Electrified Vertical Take Off and Landing↗
NASA NTRS2019

Fabrication and Performance of NiCuCoFeMn High Entropy Alloy Nanopastes for Brazing Inconel 718

Overview: High entropy alloys (HEAs) are a class of metallic alloys consisting of 5 plus elemental components and have four core effects - 1. High mixing entropy - 2. Sluggish diffusion kinetics - 3. High lattice distortion - 4. Cocktail effect; Boron-free, silicon-free brazing materials for nickel superalloys to avoid brittle intermetallic and eutectic phase formation; Size-dependent melting point depression can eliminate the need for boron, silicon and other melting point depressants; A Ni-Mn-Fe-Co-Cu HEA with low solidus and liquidus temperatures (1080 °C and 1150 °C) was developed; Low solidus and liquidus temperatures of the HEA combined with the nanoscale melting point depression in this study; Bulk HEA fabricated by induction melting of elemental powders; HEA nanoparticles (NPs) fabricated by ball milling of the HEA micropowder; Inconel 718 was laser brazed in air using the HEA and bulk and NP performances are compared.

Bridges, Denzel↗
NASA NTRS2018

High-Efficiency Flexible Multilevel Photon Sieves by Single-Step Laser-Based Fabrication and Optical Analysis

Over the past several decades, the need for high-resolution, high-efficiency, lightweight, high contrast focusing optics has continued to increase due to their applications in fields such as astronomy, spectroscopy, free-space optical communications, defense, and remote sensing. In recent years, photon sieve planar diffractive optics have been developed on flexible, lightweight polyimide substrates. However, transmission efficiencies have continuously been very low (~1-4%), thus impeding the widespread use of photon sieves in practical applications. Here, we present a flexible, lightweight, N = 4 level phase photon sieve with over 25% transmission efficiency; nearly triple that of any other photon sieve reported thus far. In this study, the photon sieve was fabricated via a novel pulsed laser ablation method using an ultraviolet source, and the total time to fabricate a ~3 sq cm sample was tens of seconds. Theoretical analysis of the photon sieve was carried out via the FDTD method, and was in very good agreement with experimental results. We also calculated via FDTD modeling the behavior of higher step (N = 8, 16, 32) photon sieves for further enhanced efficiencies, and show a fundamental limit on photon sieve efficiency of 70% in the limit of increasing step number. This multilevel photon sieve represents a new step in high-resolution diffractive optics, moving towards efficiencies suitable for widespread applications.

Julian, Matthew N.↗
NASA NTRS2019

Air Mobility Data & Reasoning Fabric

Introduce mobility challenge, how air mobility can address the mobility challenge, then how an Air Mobility Data & Reasoning Fabric can enable the envisioned future air mobility. Poses the question of what is an effective role for NASA in enabling an Air Mobility Data & Reasoning Fabric.

Van Dalsem, William R.↗
NASA NTRSDate not supplied

Metal Fused Filament Fabrication of Titanium Alloy for In Space Manufacturing

NASA is developing materials and processes for the in-space manufacturing of many items for the International Space Station (ISS) and future exploration platforms. These new manufacturing processes will require the further development of current 3D printing processes to achieve high-performance metal parts within the power and space constraints of the ISS. Manufacturing Ti-6Al-4V alloy parts with 3D printing using a metal fused filament fabrication (MF3) process is an alternative process to the Direct Metal Laser Sintering (DMLS) of the metal powders additive manufacturing process. Our initial work fabricating Ti-6Al-4V parts from Ti-6Al-4V powder-binder feedstock and processed with the MF3 process has resulted in 95-97% sintered densities. The current development work of optimized sintered properties investigates the effects of variation in sintering time, temperature, and vacuum on the sintered properties of Ti-6Al-4V MF3 printed tensile bars. Sintered properties such as density, hardness, and tensile properties were characterized followed by microstructural and chemical (O/C/N) analysis to understand the role of sintering process on the ensuing material properties. Future development of the MF3 process will also involve investigation of the effects of micro-milling the Ti-64Al-4V powder to nanometer particle sizes and the investigation of laser sintering of the 3D printed devices. This new micro-milling technique will have broad application to other areas that require particle size reduction of hard metallic materials, such as Nuclear Thermal Propulsion and other NASA technologies. Laser sintering in lieu of high temperature thermal sintering should allow for significant power reduction and improved processing speeds.

sintering, alloys, 3D printing↗
NASA NTRS1996

Design, Fabrication and Testing of 30-cm Dia. Dished Carbon-Carbon Ion Engine Grids

Two sets of 30-cm dia. dished carbon-carbon ion engine grid sets were fabricated, assembled and tested. The carbon-carbon grid blanks were fabricated from unidirectional prepreg tape, having a very high fiber volume fraction of 57 percent and resulting in the strongest quasi-isotropic carbon-carbon material known to the authors. The flexural modulus of the panel material was measured at 275 MPa, corresponding to 80 percent of the value of molybdenum.

ion↗
NASA NTRS2017

Fabrication of coronagraph masks and laboratory scale star-shade masks: characteristics, defects and performance

NASA WFIRST mission has planned to include a coronagraph instrument to find and characterize exoplanets. Masks are needed to suppress the host star light to better than 10-8 – 10-9 level contrast over a broad bandwidth to enable the coronagraph mission objectives. Such masks for high contrast coronagraphic imaging require various fabrication technologies to meet a wide range of specifications, including precise shapes, micron scale island features, ultra-low reflectivity regions, uniformity, wave front quality, etc. We present the technologies employed at JPL to produce these pupil plane and image plane coronagraph masks, and lab-scale external occulter masks, highlighting accomplishments from the high contrast imaging testbed (HCIT) at JPL and from the high contrast imaging lab (HCIL) at Princeton University. Inherent systematic and random errors in fabrication and their impact on coronagraph performance are discussed with model predictions and measurements.

Casey Wilson, Robert↗
NASA NTRS2019

Fabrication of Phononic Filter Structures for Far-IR/sub-mm Detector Applications

A photon noise limited sub-mm/far-IR cold telescope in space will require detectors with noise equivalent power (NEP) less than 1x10-19W/Hz1/2for imaging applications and at least an order of magnitude lower for spectroscopic studies. The detector NEP can be reduced by lowering the operation temperature and improving the thermal isolation between the bolometer and a heat bath. We report on the fabrication of membrane isolated transition edge sensor bolometers incorporating compact (<50 μm) thermal isolation beams based on phononic filters. Phononic filters are created by etching quasi-periodic nanoscale structures into supporting thermo-mechanical beams. The cross-sectional dimensions of the etched features are less than the thermal wavelength at the operating temperature, enabling coherent phonon transport to take place in one dimension. The phonon stop-band can be tuned by adjusting the scale of the quasi-periodic structures. Cascading multiple filter stages can increase bandwidth and provide improved thermal isolation similar to the function of a multi-stage electrical filter. We describe the fabrication of AlMn based transition edge sensor bolometers on silicon and silicon nitride membranes isolated by one-and two-dimensional phononic filters. The phononic filters are patterned through electron beam lithography and isolated with deep reactive ion etching.

Phononic↗
NASA NTRSDate not supplied

Fabrication of monocrystalline silicon x-ray mirrors

Progress within the fi eld of x-ray astronomy depends on astronomical x-ray observations of ever-increasing quality and speed. Fast and high-resolution x-ray observations over a broad spectral range promise amazing new discoveries. These observations, however, require a spaceborne x-ray telescope of unprecedented imaging power. Of the numerous technological concerns associated with the design and construction of such a telescope, the x-ray focusing optics present a particularly complex and arduous set of challenges. An x-ray optical assembly comprises many thousands of x-ray mirrors, a most critical element. Our group at NASA Goddard Space Flight Center (GSFC) pursues the development of an x-ray mirror manufacturing process capable of meeting the stringent quality, production time, and cost requirements of the next-generation of x-ray telescopes. The manufacturing process employs monocrystalline silicon: a lightweight, stiff, thermally conductive, and readily available material which is free of internal stress; it is a nearly ideal material for a thin mirror substrate. The process involves various traditional optical fabrication techniques adapted to x-ray mirror geometry. Presently, our process is capable of fabricating sub-arcsecond half-power diameter (HPD) resolution mirror pairs (primary and secondary) at a mirror thickness of 0.5 mm and of virtually any x-ray optical design (e.g. Wolter-I, Wolter-Schwarzschild, etc.). The mirror substrate surface quality is comparable to, and sometimes exceeding, that of the mirrors on the Chandra X-ray Observatory. This paper describes the various manufacturing steps involved in the production of x-ray mirror substrates and a present status report.

Raul E. Riveros↗
NASA NTRS2019

Highly Absorptive Pupil Mask Fabricated with Black Silicon

Many of NASA’s direct imaging of exoplanet missions and projects require fabricated coronagraph masks to control scattering and diffraction of light. The designed, patterned mask intended for the coronagraphic testbeds are highly absorptive in the visible range on non-metallic regions. In this work, we employed the cryogenic etching process to fabricate black silicon (BSi) to achieve a high aspect ratio (HAR) structures with higher etch rate than conventional reactive ion etching (REI). Recent bidirectional reflectance distribution function (BRDF) measurements of uniformly etched BSi on silicon wafer show highly diffusive BSi with a specular reflective component in the orders of seven magnitudes lower than the total hemispherical reflectance when the polarized or non-polarized incident beam is used.

black-silicon↗
NASA NTRSDate not supplied

Toward the fabrication of a 5 μm resolution Wolter microscope for the National Ignition Facility

Advancements in computer-controlled polishing, metrology, and replication have led to a x-ray mirror fabrication process that is capable of producing high-resolution Wolter microscopes. The mirror is a nickel-cobalt replicated full-shell mirror that was electroformed from a finely figured and polished mandrel. This mandrel was designed and fabricated for a 8 m source-to-detector distance microscope, with 10× magnification. A computer controlled polishing process corrected the low-frequency mandrel figure to < 2.0 nm RMS error. The mandrel design was optimized to reduce shell distortions that occur mainly < 20 mm from the shell ends. This design, in combination with improved replication tooling design and refined bath parameters informed by a detailed COMSOL model, have led to reductions in replication errors in the mirror shell. X-ray tests performed on a pair of mirror shells replicated from the mandrel have demonstrated < 10 μm FWHM source plane imaging resolution. Here we discuss the development process, highlight results from metrology and x-ray testing, and define a path for achieving 5 μm FWHM resolution.

Grazing Incidence, Wolter Microscope, X-ray Optics↗