Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ENGINE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Advanced engine study for mixed-mode orbit-transfer vehicles

Engine design, performance, weight and envelope data were established for three mixed-mode orbit-transfer vehicle engine candidates. Engine concepts evaluated are the tripropellant, dual-expander and plug cluster. Oxygen, RP-1 and hydrogen are the propellants considered for use in these engines. Theoretical performance and propellant properties were established for bipropellant and tripropellant mixes of these propellants. RP-1, hydrogen and oxygen were evaluated as coolants and the maximum attainable chamber pressures were determined for each engine concept within the constraints of the propellant properties and the low cycle thermal fatigue (300 cycles) requirement. The baseline engine design and component operating characteristics are determined at a thrust level of 88,964N (20,000 lbs) and a thrust split of 0.5. The parametric data is generated over ranges of thrust and thrust split of 66.7 to 400kN (15 to 90 klb) and 0.4 to 0.8, respectively.

Mellish, J. A.↗
NASA NTRS1979

Investigation of wing shielding effects on CTOL engine noise

A full scale engine wing shielding investigation was conducted at the Lewis Research Center using a 97,900-N (22,000 lb) thrust turbofan engine and a simulated wing section sized around a conventional-take-off type four-engine narrow body airplane. Sound data were obtained for the wing placed at seven positions in a plane parallel to the engine axis, and were compared to data obtained without the wing at both take off and approach power. In addition, the engine was operated with and without extensive acoustic treatment, including a sonic inlet in order to evaluate wing shielding effectiveness with a highly suppressed engine. The wing shielding effectiveness was also calibrated using a 3.8 cm diam air nozzle as a second source. Results indicated that even though about 10 dB broad band shielding was achieved, the equivalent flyover noise reduction was less than 3.0 EPNdB for most configurations.

Bloomer, H. E.↗
NASA NTRS1978

Design of a preprototype Stirling Laboratory Research Engine

A description is given for the design and fabrication of a first generation, preprototype Stirling Laboratory Research Engine. The engine represents the first step in providing a research tool to be used to support the development of a broad range of analytical modeling and experimental efforts, and to evaluate new approaches to the design of components for Stirling engines. The test engine is a horizontally-opposed, two-piston, single-acting machine with a dual crankshaft drive mechanism. The preprototype engine is rated at 10 kW and was designed for maximum modularity. The long term objective of the project is to provide a proven design of a standardized test engine, which can be commercially produced, for national research on Stirling cycle machines.

Hoehn, F. W.↗
NASA NTRS1979

Investigation of wing shielding effects on CTOL engine noise

A full scale engine wing shielding investigation was conducted at the Lewis Research Center using a 97,900-N (22,000 lb) thrust turbofan engine and a simulated wing section sized around a conventional-take-off type four-engine narrow body airplane. Sound data were obtained for the wing placed at seven positions in a plane parallel to the engine axis, and were compared to data obtained without the wing at both take off and approach power. In addition the engine was operated with and without extensive acoustic treatment including a sonic inlet in order to evaluate wing shielding effectiveness with a highly suppressed engine. The wing shielding effectiveness was also calibrated using a 3.8 cm diam air nozzle as a sound source. Results indicated that even though about 10 dB broad band shielding was achieved, the equivalent flyover noise reduction was less than 3.0 EPNdB for most configurations.

Bloomer, H. E.↗
NASA NTRS1979

A review of Curtiss-Wright rotary engine developments with respect to general aviation potential

Aviation related rotary (Wankel-type) engine tests, possible growth directions and relevant developments at Curtiss-Wright have been reviewed. Automotive rotary engines including stratified charge are described and flight test results of rotary aircraft engines are presented. The current 300 HP engine prototype shows basic durability and competitive performance potential. Recent parallel developments have separately confirmed the geometric advantages of the rotary engine for direct injected unthrottled stratified charge. Specific fuel consumption equal to or better than pre- or swirl-chamber diesels, low emission and multi-fuel capability have been shown by rig tests of similar rotary engine.

Jones, C.↗
NASA NTRS1979

Brayton engines for dispersed solar power

This paper describes the procedures being used to characterize and to analyze Brayton cycle gas turbines for application in dispersed solar electrical power plants whose cost of electricity is economically viable. Three Brayton engine types are under consideration - atmospheric (an open cycle engine), subatmospheric (also an open cycle engine) and the closed cycle engine. This analysis will be utilized to identify and select suitable candidates from existing engine configurations for near-term system demonstrations and to define optimum configurations for production in the 1990 era. Engine designs are being targeted to a system specific capital cost goal of 1000 dollars per design kilowatt, a value believed to make the cost of solar generated electricity competitive.

Ashe, T. L.↗
NASA NTRS1979

Plug cluster engine concept for in-space missions

The development of a suitable orbital transfer vehicle (OTV) engine is discussed. The OTV's dimensions are limited by those of the Space Shuttle payload bay on which it will be carried. An approach to utilize the available diameter to achieve high area ratio and thus high engine performance, is presented. Unconventional nozzles, such as clusters of small thrusters around a large diameter contoured plug, are investigated to arrive at engine designs which feature lower chamber pressures, with attendant lower heat flux, lower wall temperature, longer fatigue life, and less critical turbomachinery. Attention is also given to plug nozzle technology, high area ratio module- and scarfed bell- Plug Cluster Engine (PCE) concepts, as well as PCE performance, weight, and assessment. A conceptual design of a PCE formed from a cluster of high area ratio, scarfed, bell nozzles proved to be competitive with bell and spike nozzle engines. PCE advantages cited include increased payload length due to shorter engine length, ability to increase or decrease the number of modules and thereby the thrust, and low cost due to utilization of off-the-shelf technology.

Obrien, C. J.↗
NASA NTRS1979

Dynamics and control of Stirling engines in a 15 kWe solar electric generation concept

This paper discusses the application of kinematic and free piston Stirling engines in a 15 kWe dish-electric approach for solar thermal electric generation. Initially, the principle of operation of Stirling engines in solar thermal electric generation is discussed. Then, under certain simplifying assumptions, mathematical models describing the dynamic operation of the kinematic and free piston Stirling engines are developed. It is found that the engine dynamics may be approximated by second order models. Control mechanisms for both types of Stirling engines are discussed. An approach based on the modulation of the working fluid mean pressure is presented. It is concluded that this approach offers a fast and effective means of control. The free piston Stirling engine, being a thermally driven mechanical oscillator, presents unique control requirements. These are discussed in this paper.

Das, R. L.↗
NASA NTRS1977

Start up system for hydrogen generator used with an internal combustion engine

A hydrogen generator provides hydrogen rich product gases which are mixed with the fuel being supplied to an internal combustion engine for the purpose of enabling a very lean mixture of that fuel to be used, whereby nitrous oxides emitted by the engine are minimized. The hydrogen generator contains a catalyst which must be heated to a pre-determined temperature before it can react properly. To simplify the process of heating up the catalyst at start-up time, either some of the energy produced by the engine such as engine exhaust gas, or electrical energy produced by the engine, or the engine exhaust gas may be used to heat up air which is then used to heat the catalyst.

Houseman, J.↗
NASA NTRS1979

Orbital Transfer Vehicle (OTV) engine study. Phase A: Extension

An orbital transfer vehicle OTV engine study program was undertaken to provide additional expander and staged combustion cycle data in the design definition of the OTV engine. The proposed program effort optimizes the expander cycle engine concept (consistent with identified OTV engine requirements), investigates the feasibility of kitting the staged combustion cycle engine to provide extended low thrust operation, and conducts in-depth analysis of development risk, crew safety, and reliability for both cycles. Additional tasks to establish the cost of a 10K thrust expander cycle engine and to render support of OTV systems study contractors are reported.

Sobin, A. J.↗
NASA NTRS1977

Quiet Clean Short-haul Experimental Engine (QCSEE) main reduction gears test program

Sets of under the wing (UTW) engine reduction gears and sets of over the wing (OTW) engine reduction gears were fabricated for rig testing and subsequent installation in engines. The UTW engine reduction gears which have a ratio of 2.465:1 and a design rating of 9712 kW at 3157 rpm fan speed were operated at up to 105% speed at 60% torque and 100% speed at 125% torque. The OTW engine reduction gears which have a ratio of 2.062:1 and a design rating of 12,615 kW at 3861 rpm fan speed were operated at up to 95% speed at 50% torque and 80% speed at 109% torque. Satisfactory operation was demonstrated at powers up to 12,172 kW, mechanical efficiency up to 99.1% UTW, and a maximum gear pitch line velocity of 112 m/s (22,300 fpm) with a corresponding star gear spherical roller bearing DN of 850,00 OTW. Oil and star gear bearing temperatures, oil churning, heat rejection, and vibratory characteristics were acceptable for engine installation.

Misel, O. W.↗
NASA NTRS1980

Overview of a stirling engine test project

Tests were conducted on three Stirling engines ranging in size from 1.33 to 53 horsepower (1 to 40 kW). The tests were directed toward developing alternative, backup component concepts to improve engine efficiency and performance or to reduce costs. Some of the activities included investigating attractive concepts and materials for cooler-regenerator units, installing a jet impingement device on a Stirling engine to determine its potential for improved engine performance, and presenting performance maps for initial characterization of Stirling engines. The experiment results of the tests are presented along with predictions of results of future tests to be conducted on the Stirling engines.

Slaby, J. G.↗
NASA NTRS1980

Orbital Transfer Vehicle (OTV) engine study phase A, extension

The current Phase A-Extension of the OTV engine study program seeks to provide additional expander and staged combustion cycle data that will lead to design definition of the OTV engine. The proposed program effort will optimize the expander cycle engine concept (consistent with identified OTV engine requirements), investigate the feasibility of kitting the stage combustion cycle engine to provide extended low thrust operation, and conduct in-depth analysis of development risk, crew safety, and reliability for both cycles. Additional task will address costing of a 10k thrust expander cycle engine and support of OTV systems study contractors.

Sobin, A. J.↗
NASA NTRS1978

Performance deterioration based on existing (historical) data; JT9D jet engine diagnostics program

The results of the collection and analysis of historical data pertaining to the deterioration of JT9D engine performance are presented. The results of analyses of prerepair and postrepair engine test stand performance data from a number of airlines to establish the individual as well as average losses in engine performance with respect to service use are included. Analysis of the changes in mechanical condition of parts, obtained by inspection of used gas-path parts of varying age, allowed preliminary assessments of component performance deterioration levels and identification of the causitive factors. These component performance estimates, refined by data from special engine back-to-back testing related to module performance restoration, permitted the development of preliminary models of engine component/module performance deterioration with respect to usage. The preliminary assessment of the causes of module performance deterioration and the trends with usage are explained, along with the role each module plays in overall engine performance deterioration. Preliminary recommendations with respect to operating and maintenance practices which could be adopted to control the level of performance deterioration are presented. The needs for additional component sensitivity testing as well as outstanding issues are discussed.

Sallee, G. P.↗
NASA NTRS1980

AiResearch QCGAT engine, airplane, and nacelle design features

The quiet, clean, general aviation turbofan engine and nacelle system was designed and tested. The engine utilized the core of the AiResearch model TFE731-3 engine and incorporated several unique noise- and emissions-reduction features. Components that were successfully adapted to this core include the fan, gearbox, combustor, low-pressure turbine, and associated structure. A highly versatile workhorse nacelle incorporating interchangeable acoustic and hardwall duct liners, showed that large-engine attenuation technology could be applied to small propulsion engines. The application of the mixer compound nozzle demonstrated both performance and noise advantages on the engine. Major performance, emissions, and noise goals were demonstrated.

Heldenbrand, R. W.↗
NASA NTRS1980

New opportunities for future, small, General-Aviation Turbine Engines (GATE)

The results of four independent contracted studies to explore the opportunities for future small turbine engines are summarized in a composite overview. Candidate advanced technologies are screened, various cycles and staging arrangements are parametrically evaluated, and optimum conceptual engines are identified for a range of 300 to 600 horsepower applications. Engine improvements of 20 percent in specific fuel consumption and 40 percent in engine cost were forecast using high risk technologies that could be technically demonstrated by 1988. The ensuing economic benefits are in the neighborhood of 20 to 30 percent for twin-engine aircraft currently powered by piston engines.

Strack, W. C.↗
NASA NTRS1980

CF6 jet engine performance improvement: New fan

As part of the NASA sponsored engine component improvement program, and fan package was developed to reduce fuel consumption in current CF6 turbofan aircraft engine. The new fan package consist of an improved fan blade, reduced fan tip clearance due to a fan case stiffener, and a smooth fan casing tip shroud. CF6 engine performance and acoustic tests demonstrated the predicted 1.8% improvement in cruise sfc without an increase in engine noise. Power management thrust/fan speed characteristics were defined. Mechanical and structural integrity was demonstrated in model fan rotor photoelastic stress tests, full-size fan blade bench fatigue tests, and CF6 engine bird ingestion, crosswind, and cyclic endurance tests. The fan was certified in the CF6-500c2/E2 engines and is in commerical service on the Boeing 747-200, Douglas DC-10-30, and Atrbus industrie A300B aircraft.

Fasching, W. A.↗
NASA NTRS1980

Orbital Transfer Vehicle (OTV) engine study. Phase A: Extension

The current Phase A-Extension of the OTV engine study program aims to provide additional expander and staged combustion cycle data that will lead to design definition of the OTV engine. The proposed program effort seeks to optimize the expander cycle engine concept (consistent with identified OTV engine requirements), investigate the feasibility of kitting the staged combustion cycle engine to provide extended thrust operation, and conduct in-depth analysis of development risk, crew safety, and reliability for both cycles. Additional tasks address the costing of a 10/K thrust expander cycle engine and support of OTV systems study contractors.

Sobin, A. J.↗