Experimental observation of a large addition to the electron inner radiation belt after a solar flare event.
Electron injection and diffusion into electron inner radiation belt after solar flare, measuring electron fluxes by OGO 3 spectrometer
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Electron injection and diffusion into electron inner radiation belt after solar flare, measuring electron fluxes by OGO 3 spectrometer
Electron traceless pressure and heat flow for weakly ionized electron gas in DC magnetic field assuming electron-neutral collisions dominate
Scanning microscope uses a field-emission tip for the electron source, an electron gun that simultaneously accelerates and focuses electrons from the source, and one auxiliary lens to produce a final probe size at the specimen on the order of angstroms.
Data on the scattering of 1-MeV electrons in aluminum for the case of non-normal incidence, electron-bremsstrahlung cross-sections in thin targets, and the production of bremstrahlung by electron interaction in thick targets, are presented both in tabular and graphic form. These results may interest physicists and radiologists.
IMP 4 satellite measurements of cosmic ray electrons in interplanetary space compared to predictions of electron intensity from interstellar proton-electron collisions
Electron-electron correlation effects in photoabsorption induced double electron ejection process, using many body perturbation theory
Application of electron beam lithography to replace photolithography process in fabrication of integrated circuits is discussed. Procedure for using electron beam lithography equipment is described. Diagram of electron micropattern generator is provided.
Positive-ion and electron densities were measured in the 75 to 110 km altitude range with the aid of two rockets launched from White Sands near sunrise. The solar zenith angles were 91 and 79 deg respectively. The densities were derived from measurements made by an ion collector and from data obtained with a Faraday rotation technique capable of detecting electrons in the D-region. It has been found that in the 80-95 km altitude range, electron detachment from negative ions takes place mainly at zenith angles of less than 91 deg. The source of the high positive-ion density (N(+) approximately 700/cu cm) at an altitude of 75 km just before sunrise is presumed to be scattered Lyman alpha radiation which is ionizing nitric oxide.
The feasibility of using the interaction between a thin, solid, spiraling electron beam of 10 to 20 kV energy and a microwave cavity to generate watts of CW millimeter-wave power was investigated. Experimental results are given for several prototype devices operating at 9.4 GHz and at 94 GHz. Power outputs of 5 W, and electronic efficiencies near 3%, were obtained at X band, and moderate gain was obtained at 94 GHz. The small-signal theory gives a good fit to the X-band data, and the device behavior at 94 GHz is as expected from the given beam characteristics. The performance is limited chiefly by the velocity spread in the spiraling electron beam, and once this can be brought under control, high-power generation of millimeter waves appears quite feasible with this type of device.
Criteria and recommended practices for the design of the spaceborne elements of electronic imaging systems are presented. A spaceborne electronic imaging system is defined as a device that collects energy in some portion of the electromagnetic spectrum with detector(s) whose direct output is an electrical signal that can be processed (using direct transmission or delayed transmission after recording) to form a pictorial image. This definition encompasses both image tube systems and scanning point-detector systems. The intent was to collect the design experience and recommended practice of the several systems possessing the common denominator of acquiring images from space electronically and to maintain the system viewpoint rather than pursuing specialization in devices. The devices may be markedly different physically, but each was designed to provide a particular type of image within particular limitations. Performance parameters which determine the type of system selected for a given mission and which influence the design include: Sensitivity, Resolution, Dynamic range, Spectral response, Frame rate/bandwidth, Optics compatibility, Image motion, Radiation resistance, Size, Weight, Power, and Reliability.
The electron spectrum predicted for the synchronous orbit was simulated to determine the effects that might occur to astroscientists exposed to such irradiation while on a prolonged space station mission in that region. Miniature pigs were exposed to monoenergetic and spectral-fractionated irradiations with 0.5 to 2.1 MeV electrons. Clinical and pathological alterations observed in biopsies were correlated with depth-dose pattern and length of post irradiation period up to one year. With monoenergetic electrons, the lowest dose causing a recognizable lesion was 1450 rad and with increasing dose lesions appeared earlier and were more severe. At the highest dose given, 2650 rad, ulceration extending into the dermis was present by twenty one days and required about four months for complete healing. Spectral-fractionated irradiations, in which the total dose range was essentially comparable to that of the monoenergetic series, resulted in very minimal outer dermis edema at 1790 rad and at no dose employed did necrosis of epidermis or ulceration into dermis occur.
A computer technique for treating the motion of charged and neutral particles and called the phase space time evolution method was developed. This technique employs the computer's bookkeeping capacity to keep track of the time development of a phase space distribution of particles. This method was applied to a study of the penetration of electrons. A 1 MeV beam of electrons normally incident on a semi-infinite slab of aluminum was used. Results of the calculation were compared with Monte Carlo calculations and experimental results. Time-dependent PSTE electron penetration results for the same problem are presented.
Experimental data acquired over the past few years were gathered, and parametric fits made to these data. The following properties of electron transport were represented by simple functions of atomic number and energy: transmitted electron number, transmitted electron spectra, range, backscatter coefficient, angular distribution, energy deposition, bremsstrahlung intensity and energy spectra, and bremsstrahlung angular distribution and photon attenuation. The formulas cover the energy ranges of interest in space shielding problems (0.1 to 10.0 MeV). Procedures for using these formulas in practical situations are suggested.
Vacuum ultraviolet multiplets of C I, C II, and O I were produced by electron impact of CO2. Absolute emission cross sections for these multiplets were measured from threshold to 350 eV. The electrostatically focussed electron gun used in this series of experiments is described in detail. The atomic multiplets which were produced by dissociative excitation of CO2 and the cross sections at 100 eV are given. The dependence of the excitation functions on electron energy shows that these multiplets are produced by electric-dipole-allowed transitions in CO2.
Vacuum ultraviolet multiplets of C I, C II, and O I were produced by electron impact on CO2. Absolute emission cross sections for these multiplets were measured from threshold to 350 eV. The electrostatically focused electron gun used is described in detail. The atomic multiplets which were produced by dissociative excitation of CO2 and the cross sections at 100 eV are presented. The dependence of the excitation functions on electron energy shows that these multiplets are produced by electric-dipole-allowed transitions in CO2.
Two independent methods for measuring the electron intensity in interstellar space are proposed. The positron method involves the production of pions in proton-proton collisions, the decay of the pions into muons, and the subsequent decay of the muons into positrons. Results from detailed calculations of these processes are given in graphical form. The second method involves cosmic electron emitted synchrotron radiation in the interstellar magnetic field. These two methods are also used to analyze the spatial and temporal constancy of cosmic ray electrons in the galaxy.
An investigation was conducted to determine the effects of alloy additions of hafnium, tantalum, tungsten, rhenium, osmium, iridium, and platinum on hardness of molybdenum. Special emphasis was placed on alloy softening in these binary molybdenum alloys. Results showed that alloy softening was produced by those elements having an excess of s+d electrons compared to molybdenum, while those elements having an equal number or fewer s+d electrons that molybdenum failed to produce alloy softening. Alloy softening and alloy hardening can be correlated with the difference in number of s+d electrons of the solute element and molybdenum.
Satellite measurements of field-aligned auroral electron precipitation were analyzed using 16 months of data from the OGO-4 auroral particles experiment. It was observed that the anisotropies are of short time duration and are most likely to occur when particle fluxes are high. Field-aligned 2.3 keV electron precipitation is found in an oval shaped region primarily in the nighttime hours, with a maximum probability at approximately 70 deg invariant latitude near midnight, congruent to and poleward of the auroral optical emissions in these hours. This precipitation was found to be associated with the high latitude boundary of auroral electron precipitation during substorm expansion and is characterized by a harder and more intense energy spectrum than typical isotropic precipitation.