Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELASTIC PROPERTY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92

Tip-induced deformation of a phospholipid bilayer: Theoretical perspective of sum frequency generation imaging

The paper addresses theory of Sum Frequency Generation imaging of an atomic force microscopy tip-induced deformation of a bilayer phospholipid membrane deposited over a pore: known as a nano-drum system. Image modeling employed nonlinearities of the normal modes specific to hydrocarbon terminal methyls, which are distributed about the deformed surfaces of inner and outer leaflets. The deformed profiles are according to the solutions of shape equation for Canham-Helfrich Hamiltonian accounting properties of four membranes, which differ in elasticity and adhesion. The results indicate that in continuous deformed surfaces, the difference in the curvature of the outer and inner leaflets dominates in the imaged nonlinearity. This is different comparing to the results for a perfect bilayer spherical cap system (the subject of previous study), where nonlinear image response is dominated by the mismatch of the inner and outer leaflets’ surface areas (as projected to the image plane) at the edge of perfectly spherical structure. The results of theoretical studies, here, demonstrate that Sum Frequency Generation imaging in continuous and deformed bilayer surfaces are helpful to address curvature locally and anticipate mechanical properties of membrane. The articles discuss applicability and practical limitations of the approach. Combination of Atomic Force Microscopy and Sum Frequency Generation imaging under controlled tip-induced deformation provides a good opportunity to probe and test membranes physical properties with rigor of adopted theory.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Predicting Elastic Constants of Refractory Complex Concentrated Alloys Using Machine Learning Approach

Refractory complex concentrated alloys (RCCAs) have drawn increasing attention recently owing to their balanced mechanical properties, including excellent creep resistance, ductility, and oxidation resistance. The mechanical and thermal properties of RCCAs are directly linked with the elastic constants. However, it is time consuming and expensive to obtain the elastic constants of RCCAs with conventional trial-and-error experiments. The elastic constants of RCCAs are predicted using a combination of density functional theory simulation data and machine learning (ML) algorithms in this study. The elastic constants of several RCCAs are predicted using the random forest regressor, gradient boosting regressor (GBR), and XGBoost regression models. Based on performance metrics R-squared, mean average error and root mean square error, the GBR model was found to be most promising in predicting the elastic constant of RCCAs among the three ML models. Additionally, GBR model accuracy was verified using the other four RHEAs dataset which was never seen by the GBR model, and reasonable agreements between ML prediction and available results were found. The present findings show that the GBR model can be used to predict the elastic constant of new RHEAs more accurately without performing any expensive computational and experimental work.

36 MATERIALS SCIENCE↗

Ab initio property predictions of quinary solid solutions using small binary cells

The Set of Small Ordered Structures (SSOS) approach is an ab initio technique for modelling random solid solutions in which many small structures are averaged so that their correlation functions match those of a desired composition. SSOS has been shown to be effective in reducing the cost of density functional theory calculations relative to other well-known techniques such as cluster expansions and special quasirandom structures for modelling solid solutions. Here in this work, we demonstrate that SSOS’s can be constructed using cells with only a subset of elements while still accurately modelling multi-component systems. Specifically, we show that small binary cells can effectively model two quinary high entropy alloys – NbTaTiHfZr and MoNbTaVW – accurately capturing properties such as formation energy, lattice parameters, elastic constants, and root-mean-square atomic displacements. Overall, this insight is useful for those looking to construct databases of such small structures for predicting the properties of multi-component solid solutions, as it greatly decreases the number of structures that needs to be considered.

36 MATERIALS SCIENCE↗

Temperature dependence of mechanical and thermal expansion properties of T300/5208 graphite/epoxy

The 116-394 K temperature range elastic constants, ultimate strengths and thermal expansion behavior of T300/5208 graphite/epoxy laminates of various different lay-up types have been determined. It is noted that most properties exhibit nearly linear temperature dependencies, although the transverse modulus and axial thermal expansion vary nonlinearly with temperature, and change in value by an order of magnitude over the present temperature range.

Hyer, M. W.↗

Filtered pulsed cathodic arc deposition of fullerene-like carbon and carbon nitride films

Carbon and carbon nitride films (CN{sub x}, 0 ≤ x ≤ 0.26) were deposited by filtered pulsed cathodic arc and were investigated using transmission electron microscopy and X-ray photoelectron spectroscopy. A “fullerene-like” (FL) structure of ordered graphitic planes, similar to that of magnetron sputtered FL-CN{sub x} films, was observed in films deposited at 175 °C and above, with N{sub 2} pressures of 0 and 0.5 mTorr. Higher substrate temperatures and significant nitrogen incorporation are required to produce similar FL structure by sputtering, which may, at least in part, be explained by the high ion charge states and ion energies characteristic of arc deposition. A gradual transition from majority sp{sup 3}-hybridized films to sp{sup 2} films was observed with increasing substrate temperature. High elastic recovery, an attractive characteristic mechanical property of FL-CN{sub x} films, is evident in arc-deposited films both with and without nitrogen content, and both with and without FL structure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Temperature-dependent elastic constants of thorium dioxide probed using time-domain Brillouin scattering

Herein we report the adiabatic elastic constants of single-crystal thorium dioxide over a temperature range of 77–350 K. Time-domain Brillouin scattering, an all-optical, non-contact picosecond ultrasonic technique, is used to generate and detect coherent acoustic phonons that propagate in the bulk perpendicular to the surface of the crystal. These coherent acoustic lattice vibrations have been monitored in two hydrothermally grown single-crystal thorium dioxide samples along the (100) and (311) crystallographic directions. The three independent elastic constants of the cubic crystal (C 11 , C 12 , and C 44 ) are determined from the measured bulk acoustic velocities. The longitudinal wave along the (100) orientation provided a direct measurement of C 11 . Measurement of C 44 and C 12 was achieved by enhancing the intensity of quasi-shear mode in a (311) oriented crystal by adjusting the polarization angle relative to the crystal axes. We find the magnitude of softening of the three elastic constants to be ~2.5% over the measured temperature range. Good agreement is found between the measured elastic constants with previously reported values at room temperature, and between the measured temperature-dependent bulk modulus with calculated values. We find that semi-empirical models capturing lattice anharmonicity adequately reproduce the observed trend. We also determine the acoustic Grüneisen anharmonicity parameter from the experimentally derived temperature-dependent bulk modulus and previously reported temperature-dependent values of volumetric thermal expansion coefficient and heat capacity. This work presents measurements of the temperature-dependent elasticity in single-crystal thorium dioxide at cryogenic temperature and provides a basis for testing ab initio theoretical models and evaluating the impact of anharmonicity on thermophysical properties.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Molecular dynamics studies of fundamental bulk properties of palladium hydrides for hydrogen storage

Solid-state hydrogen storage materials undergo complex phase transformations whose behavior are collectively determined by thermodynamic (e.g., Gibbs free energy), mechanical (e.g., lattice and elastic constants), and mass transport (e.g., diffusivity) properties. These properties depend on the reaction conditions and evolve continuously during (de)hydrogenation. Thus, they are difficult to measure in experiments. Because of this, past progress to improve solid-state hydrogen storage materials has been prolonged. Using PdH x as a representative example for interstitial metal hydride, we have recently applied molecular dynamics simulations to quantify hydrogen diffusion in the entire reaction space of temperature and composition. In this paper, we have further applied molecular dynamics simulations to obtain well-converged expressions for lattice constants, Gibbs free energies, and elastic constants of PdH x at various stages of the reaction. Finally, our studies confirm significant dependence of elastic constants on temperature and composition. Specifically, a new dynamic effect of hydrogen diffusion on elastic constants is discovered and discussed.

08 HYDROGEN↗

Design optimization for Richtmyer–Meshkov instability suppression at shock-compressed material interfaces

We report the Richtmyer–Meshkov instability (RMI) is a phenomenon that occurs at the interface of two substances of different densities due to an impulsive acceleration, such as a shock wave passing through this interface. Under these conditions, the instability can be seen as interface perturbations begin to grow into narrow jets or spikes of one substance that propagate into the other. In some cases, this interface may involve an elastic–plastic material, which can play a significant role in the development and behavior of the RMI. The ability to effectively control RMI jetting and spike growth is one major limiting factor in technological challenges, such as inertial confinement fusion, that involve using high-pressure shock waves to implode a fuel target. The propagation of RMI growth can lead to increased asymmetry in this implosion process and significantly reduce the obtained energy yield. We use hydrodynamics simulations of impactor shock-compression experiments and methods based in design optimization to suppress RMI spike growth by altering the geometry and other properties of a shock-compressed elastic–plastic material target that shares an interface with atmospheric air. These hydrodynamics simulations use an arbitrary Lagrangian–Eulerian method with a high-order finite element approach. Our results demonstrate that RMI suppression can be achieved by intentionally creating a separate upstream interface instability to counteract the growth of long narrow RMI spikes at an interface with initial perturbations.

36 MATERIALS SCIENCE↗

Temperature dependencies of the elastic moduli and thermal expansion coefficient of an equiatomic, single-phase CoCrFeMnNi high-entropy alloy

The equiatomic CoCrFeMnNi alloy is now regarded as a model face-centered cubic single-phase high-entropy alloy. Consequently, determination of its intrinsic properties such as the temperature dependencies of elastic moduli and thermal expansion coefficient are important to improve understanding of this new class of material. Lastly, these temperature dependencies were measured over a large temperature range (200–1270 K) in this study.

36 MATERIALS SCIENCE↗

Diesel Fuel Property Effects on In-Cylinder Liquid Penetration Length: Impact on Smoke Emissions and Equivalence Ratio Estimates at the Flame Lift-Off Length

Here in this study, elastic scattering was employed to investigate diesel fuel property effects on the liquid length (i.e., the maximum extent of in-cylinder liquid-phase fuel penetration) using select research fuels: an ultralow-sulfur #2 diesel emissions-certification fuel (CF) and four of the Coordinating Research Council (CRC) Fuels for Advanced Combustion Engines (FACE) diesel fuels (F1, F2, F6, and F8). The experiments were performed in a single-cylinder heavy-duty optical compression-ignition engine under time-varying, noncombusting conditions to minimize the influence of chemical heat release on the liquid-length measurement. The FACE diesel fuel and CF liquid lengths under combusting conditions were also predicted using Siebers’ scaling law and pressure data from previous work using the same fuels at similar in-cylinder conditions. The objective was to observe if the liquid length under noncombusting or combusting conditions provides additional insights into the relationships among the main fuel properties (i.e., cetane number (CN), the 90 vol % distillation recovery temperature (T90), and aromatic content) and smoke emissions. Results suggest that liquid-length values are best correlated to fuel distillation characteristics measured with ASTM D2887 (simulated distillation method). This work also studied the relationship between liquid length and lift-off length, H (i.e., distance from the fuel-injector orifice exit to the position where the standing premixed autoignition zone stabilizes during mixing-controlled combustion). Two possible cases were identified based on the relative magnitudes of liquid length under combusting conditions (Lc) and H. The low-CN fuels are representative of the first case, L c < H, in which the fuel is always fully vaporized at H. The high-CN fuels are mostly representative of the second case, L c ≥ H, in which there is still liquid fuel at H. Lc ≥ H would suggest higher smoke emissions, but there is not enough evidence in this work to support a compounding effect of a longer liquid length on top of the aromatic-content effect on smoke emissions for fuels with similar CN, supporting previous findings in the literature that lift-off length plays a more important role than liquid-length on diesel combustion. At the same time, the experimental results suggest a decrease in the fuel-jet spreading angle, i.e., a decrease in the entrainment rate into the jet at and downstream of H, under combusting conditions, that is not accounted for in the model used to predict the values of $\phi$(H). Lastly, as a result, L c may be of interest for accurate predictions of $\phi$(H), especially for combustion strategies designed to lower in-cylinder soot by operating near or below the nonsooting $\phi$(H)-value (i.e., $\phi$(H) ≈ 2).

02 PETROLEUM↗

Density-functional theory for plutonium

We review here developments in the theoretical description and understanding of plutonium in terms of a metal with itinerant (band) 5f electrons. Within this picture most facets of this remarkable and anomalous material are accurately described by first-principle, parameter-free, density-functional-theory (DFT) calculations. We show that the model explains plutonium’s phase stability, elasticity, lattice vibrations, electronic structure, alloy properties, and magnetism. Fluctuations are addressed by means of constrained DFT calculations and new light is shed on the anomalous properties of δ plutonium, including explaining its negative thermal expansion. Effects of alloying and point defects in plutonium are also addressed. It is further emphasized that strong electron correlations, originating from a large intra-atomic Coulomb repulsion (~4 eV) of the 5f electrons, that has often been assumed for plutonium in the literature, is inconsistent with the experimental phase diagram of plutonium.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Cyclic nanoindentation studies on CrN thin films prepared by RF sputtering on Zr-based metallic glass

Cyclic nanoindentation tests were carried out to study the influence of the chromium nitride thin films on the mechanical properties of Zr-based metallic glass. Chromium nitride thin coatings have been deposited on Zr{sub 50}Cu{sub 40}Al{sub 10} metallic glass substrate by RF sputtering. The deposition process was done at room temperature under nitrogen reactive gas using a metallic chromium target. The CrN films have a thickness of 300 nm. Several cyclic nanoindentation measurements were conducted on CrN films and Zr{sub 50}Cu{sub 40}Al{sub 10} metallic glass substrate samples at various loading rate values. We have found that the coated metallic glass sample shows high mechanical properties such as hardness and reduced elastic modulus. Cyclic nanoindentation results show a hardening behaviour for these CrN coatings. Moreover, the CrN coated on Zr-based metallic glass was found to have a high value of resistance to crack propagation, as being analysed through the SEM pictures of the residual Vickers indentation impressions.

36 MATERIALS SCIENCE↗

Effect of Methyl Groups on Formation of Ordered or Layered Graphitic Materials from Aromatic Molecules

Abstract Developing functionally complex carbon materials from small aromatic molecules requires an understanding of how the chemistry and structure of its constituent molecules evolve and crosslink, to achieve a tailorable set of functional properties. Here, molecular dynamics (MD) simulations are used to isolate the effect of methyl groups on condensation reactions during the oxidative process and evaluate the impact on elastic modulus by considering three monodisperse pyrene‐based systems with increasing methyl group fraction. A parameter to quantify the reaction progression is designed by computing the number of new covalent bonds formed. Utilizing the previously developed MD framework, it is found that increasing methylation leads to an almost doubling of bond formation, a larger fraction of the new bonds oriented in the direction of tensile stress, and a higher basal plane alignment of the precursor molecules along the direction of tensile stress, resulting in enhanced tensile modulus. Additionally, via experiments, it is demonstrated that precursors with a higher fraction of methyl groups result in a higher alignment of molecules. Moreover, increased methylation results in the lower spread of single molecule alignment which may lead to smaller variations in tensile modulus and more consistent properties in carbon materials derived from methyl‐rich precursors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

On the validity of using the Debye model to quantitatively correlate the shear modulus with vibrational properties in cubic metals

The relationship between the shear modulus and the flexibility volume has been examined using molecular dynamics simulations in fifteen cubic metallic elements over a range of temperatures. Here we have observed a universal correlation, and identified the applicability range in which this correlation is quantitatively consistent with the prediction based on the Debye model. Deviation is observed for high modulus metals, and its origin is discussed in terms of the Debye assumptions regarding the vibrational mean squared displacement and the phonon density of states.

36 MATERIALS SCIENCE↗

Characterization of diamond-like nanocomposite thin films grown by plasma enhanced chemical vapor deposition

Diamond-like nanocomposite (DLN) thin films, comprising the networks of a-C:H and a-Si:O were deposited on pyrex glass or silicon substrate using gas precursors (e.g., hexamethyldisilane, hexamethyldisiloxane, hexamethyldisilazane, or their different combinations) mixed with argon gas, by plasma enhanced chemical vapor deposition technique. Surface morphology of DLN films was analyzed by atomic force microscopy. High-resolution transmission electron microscopic result shows that the films contain nanoparticles within the amorphous structure. Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, and x-ray photoelectron spectroscopy (XPS) were used to determine the structural change within the DLN films. The hardness and friction coefficient of the films were measured by nanoindentation and scratch test techniques, respectively. FTIR and XPS studies show the presence of C-C, C-H, Si-C, and Si-H bonds in the a-C:H and a-Si:O networks. Using Raman spectroscopy, we also found that the hardness of the DLN films varies with the intensity ratio I{sub D}/I{sub G}. Finally, we observed that the DLN films has a better performance compared to DLC, when it comes to properties like high hardness, high modulus of elasticity, low surface roughness and low friction coefficient. These characteristics are the critical components in microelectromechanical systems (MEMS) and emerging nanoelectromechanical systems (NEMS).

36 MATERIALS SCIENCE↗

Modeling of wave processes in blocky media with porous and fluid-saturated interlayers

The wave processes in blocky media are analyzed by applying different mathematical models, wherein the elastic blocks interact with each other via pliant interlayers with the complex mechanical properties. Four versions of constitutive equations are considered. In the first version, an elastic interaction between the blocks is simulated within the framework of linear elasticity theory, and the model of elastic–plastic interlayers is constructed to take into account the appearance of irreversible deformation of interlayers at short time intervals. In the second one, the effects of viscoelastic shear in the interblock interlayers are taken into the consideration using the Poynting–Thomson rheological scheme. In the third option, the model of an elastic porous material is used in the interlayers, where the pores collapse if an abrupt compressive stress is applied. In the fourth case, the model of a fluid-saturated material with open pores is examined based on Biot's equations. The collapse of pores is modeled by the generalized rheological approach, wherein the mechanical properties of a material are simulated using four rheological elements. Three of them are the traditional elastic, viscous and plastic elements, the fourth element is the so-called rigid contact, which is used to describe the behavior of materials with the different resistance to tension and compression. It was shown that the thermodynamically consistent model is provided, which means that the energy balance equation is fulfilled for an entire blocky structure, where the kinetic and potential energy of the system is the sum of the kinetic and potential energies of the blocks and interlayers. Under numerical implementation of the interlayers models, the dissipationless finite difference Ivanov's method was used. The splitting method by spatial variables in the combination with the Godunov gap decay scheme was applied in the blocks. As a result, robust and stable computational algorithms are built and tested. Using MPI technology, the parallel software was designed for the modeling of wave processes in 2D setting. The numerical results are presented, discussed and future studies are outlined. - Highlights: • We model the propagation of waves in a blocky medium with compliant interlayers. • Models of porous and fluid saturated interlayers are proposed using Biot's approach. • A parallel computational algorithm is developed for supercomputers of cluster type. • Problems of instant rotation of central and boundary blocks are solved numerically. • Wave motions are compared in the cases of elastic and fluid-saturated interlayers.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Experimental Analysis and Numerical Simulation of Tensile Behaviour of TiNi Shape Memory Alloy Fibres Reinforced Epoxy Matrix Composite at High Temperatures

The shape memory alloys (SMA) possess both sensing and actuating functions due to their shape memory effect, pseudo-elasticity, high damping capability and other remarkable properties. Combining the SMA with other materials can create intelligent or smart composites. The epoxy resin composites filled with TiNi alloys fibres were fabricated and their mechanical properties have been investigated. In this study, stress/strain relationships for a composite with embedded shape memory materials (SMA) fibres are presented. The paper illustrates influence of the SMA fibres upon changes in mechanical behaviour of a composite plate with the SMA components, firstly and secondly, the actuating ability and reliability of shape memory alloy hybrid composites.

36 MATERIALS SCIENCE↗

Overcoming geometric limitations in metallic glasses through stretch blow molding

Bulk metallic glasses (BMGs) exhibit remarkable mechanical properties, such as high strength and elasticity, which is often paired with fracture toughness. Their supercooled liquid region gives rise to plastic-like processing and suggests parts and shapes that can otherwise not be obtained for crystalline metals. However, current processing techniques only allow for limited options in terms of geometry, thicknesses uniformity, and shape complexity. Here we introduce a new processing technique, “stretch blow molding,” to expand the range of possible parts and increase the available geometries that can be fabricated with BMGs. Additionally, a model is derived that allows for the quantification and prediction of stretch blow molding and provides insight into its potential use and limitations. We demonstrate that with stretch blow molding overall strains exceeding 2000% are achievable, compared to the previously reported ~150% of blow molding. With the ability to stretch blow mold shapes that were previously unachievable with any other metal fabrication technique in a fast and economical manner, and the superb properties of BMGs, we look forward to a broad commercial adaptation of this technique.

36 MATERIALS SCIENCE↗