Results for “Complex solids” — Page 92

NASA NTRS1976

Extraction of quadrature phase information from multiple pulse NMR signals

A multiple pulse sequence (8-pulse sequence) used for high-resolution solid state NMR is analyzed with regard to the information available from each of the four wide sampling windows. It is demonstrated that full quadrature phase information can be obtained using only a single phase detector and that, for the commonly encountered situation where the spectral width is much less than the folding frequency, the signals from the various windows can be combined easily using standard complex Fourier transform software. An improvement in the signal-to-noise ratio equal to the square root of 3 is obtained over either standard single or quadrature phase detection schemes. Procedures for correcting spectral distortions are presented.

Rhim, W.-K.↗

NASA NTRS2017

The Chemistry of Pluto and its Satellites

Pluto's bulk composition and the composition of the surface layers hold clues to the origin and evolution of a number of other Solar System bodies of comparable size in the region beyond Neptune. The July 14, 2015 flyby of the Pluto system with the New Horizons spacecraft afforded the opportunity to corroborate and greatly improve discoveries about the planet and its satellites derived Earth-based studies. It also revealed extraordinary details of the surface and atmosphere of Pluto, as well as the geology and composition of Charon and two smaller satellites. With a mean density of 1.86 g/sq cm, the bulk composition of Pluto is about two-thirds anhydrous solar composition rocky material and one-third volatiles (primarily H2O in liquid and solid states) by mass, the surface is a veneer of ices dominated by N2, with smaller amounts of CH4 and CO, as well as limited exposures of H2O ice (considered to be "bedrock"). N2, CH4, and CO occur as solid solutions at temperature-dependent mutual concentrations, each component being soluble in the others. Frozen C2H6 as a minor component has also been identified. Sublimation and recondensation of N2, CH4, and CO over seasonal (248 y) and Milankovich-type megaseasons (approx. 3 My) result in the redistribution of these ices over time and with latitude control. Solid N2 is found in glaciers originating in higher elevations and flowing at the present time into a basin structure larger than the State of Texas, forming a convecting lens of N2 that overturns on a timescale of order 10 My. The varied colors of Pluto's landscape arise from the energetic processing of the surface ices in processes that break the simple molecules and reassemble complex organic structures consisting of groups of aromatic rings connected by aliphatic chains. When synthesized in the laboratory by UV or electron irradiation of a Pluto mix of ice, this material, called tholin, has colors closely similar to Pluto. The Pluto ice tholin analog contains carboxylic acids, urea, ketones, aldehydes, amines, and some nitriles. The largest satellite, Charon has density 1.70 g/sq cm and it is about 3/5 anhydrous solar composition rock, with the remainder in H2O ice. The surface H2O ice is infused in some way with NH3, probably as a hydrate, distributed nonuniformly, but to some degree related to geological structures. Pluto's atmosphere is N2, CH4, with CO, C2-hydrocarbons, HCN, and other molecules in trace but detectable amounts. The atmosphere supports a complex haze structure with about 20 discrete layers, and suspected clouds. The haze is presumed to be made of aggregates of complex hydrocarbons (tholins) produced by photolysis of the atmospheric gases, and with similar composition to the ice tholins made on the planet's surface. Urea and a suite of carboxylic acids are of interest for prebiotic and biological chemistries.

SOLAR SYSTEMS↗

NASA NTRS2024

Narragansett Bay Water Resources: Using Earth Observations to Identify Trends in Harmful Algal Blooms in Narragansett Bay

Narragansett Bay in Rhode Island is known for its quahog, or hard-shell clam, shellfisheries. However, increased levels in harmful algal blooms (HABs) and high phytoplankton biomass events pose threats to quahog populations, creating conditions that limit quahog growth and reproduction. Quahog shortages, along with public health concerns associated with contamination of shellfish from HAB-produced neurotoxins, have contributed to shellfishery closures. NASA DEVELOP partnered with the Environmental Protection Agency’s National Health and Environmental Effects Research Laboratory and Rhode Island’s Department of Environmental Management to use Earth observations and the partners’ in-situ data to visualize phytoplankton bloom events within the bay. We used Sentinel-3 Ocean and Land Color Instrument (OLCI), Landsat 8 and 9 Operational Land Imager (OLI)data to track several proxies of phytoplankton biomass from June 2016 to October 2023. Multiple sensors and in situ datasets were used to assess the feasibility of monitoring phytoplankton biomass accurately in the relatively small sized Narragansett Bay. We determined that Phytoplankton fluorescence line height was the best parameter to monitor phytoplankton biomass in the bay. Although the relatively small size of the bay and the optical complexity of these nearshore waters can pose a challenge, this assessment showed that Earth observations can be a useful complement to the in-situ monitoring of phytoplankton biomass in Narragansett Bay.

Sentinel-3↗

DOE OSTI2024

Simulation of Particulate Transport for Delivery of Solid Amendments into the Subsurface: FY24 Status Report

For particulate-based amendments to be viable for field-scale remediation at the Hanford Site (e.g., 200 DV-1 Operable Unit), particles need to be delivered a sufficient radial distance from an injection well and retained at concentrations high enough for effective treatment. An accurate description of the particle radius of influence (ROI) is critical for developing an overall remediation strategy. However, field-scale particle simulations are currently limited due to insufficient simulation capabilities and a lack of experimental data to validate and parameterize particle transport models. To help build toward field-scale deployment, this fiscal year (FY) we have (1) developed a pre screening tool to estimate particle transport, (2) implemented particle transport models within PFLOTRAN, and (3) conducted preliminary estimations of particle ROI. While field-scale numerical simulations will ultimately be necessary before remedy design and field implementation, we have developed a pre-screening tool that offers valuable estimations of expected particle injectability and ROI in a 1-D system. The advantage of the tool is that it does not require extensive laboratory experiments and instead makes predictions based solely on routine laboratory measurements. This tool can assist in down-selection and decision-making by identifying which particle amendment systems are worth pursuing in future laboratory experiments, such as 1-D column tests and beyond. With any system, scaling up from the lab to the field presents challenges. Currently, there is no field data available for model calibration or validation. However, the theoretical particle models being developed herein are the best tools available to guide progress toward field deployment. To help bridge this gap and verify model predictions, larger-scale lab experiments are being proposed. To advance simulation capabilities, six particle transport models are being integrated into the reactive transport simulator PFLOTRAN. These include colloid filtration theory (CFT) and five additional particle transport models (M1-M5). Each model, from M1 to M5, progressively incorporates additional particle transport and retention processes. Ultimately, the simplest model capable of accurately describing 1-D column data will be selected and parameterized. During FY24, the CFT and M1 model have been fully implemented within PFLOTRAN. Using an existing 1 D column experiment, the two currently implemented particle transport models (CFT and M1), and associated parameters, were fit to this experiment. While simpler model formulations are helpful for estimations, these formulations could not fully describe particle transport and retention behavior in the previous 1-D column experiment. Thus, additional complexities will need to be considered, which will be accounted for in the M2-M5 model formulations. Additionally, because a viscous, shear thinning fluid was required to keep particles in suspension, considerations for flow will also need to also be accounted for. Therefore, a new immiscible two-phase flow mode is currently being implemented in PFLOTRAN. With some modifications, this new flow module could also support simulation of non-Newtonian liquid amendments, foams, and emulsions. We also estimated the expected ROI of solid amendments using 1-D simulations. The average predicted ROI was approximately 15 ft for micron-sized zero valent iron (mZVI) suspended in xanthan gum (XG). Using the pre screening tool and ROI estimates, additional amendment-delivery laboratory characterization and experiments are proposed. The results from additional experiments can be used to validate and parametrize particulate transport model formulations, which will ultimately provide predictive capabilities for field amendment-delivery systems.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2023

Reversible solid oxide cells: Early performance and microstructural evolution during electrolysis and switched mode operation

Incorporating more renewables into our energy mix will require a diversity of technological solutions. Reversible solid oxide cell systems (RSOCs) operating reversibly between fuel cell and electrolysis modes with high round-trip efficiencies offer one such solution. However, questions remain about the stability of the oxygen and fuel electrodes under reversible operation. Here, in this study, single cells with the configuration Ni-YSZ|YSZ|GDC10|NNO-NDC50|NNO are operated by reversible cycling under potentiostatic conditions. Test conditions are chosen to be representative of average stack conditions that are likely to be encountered during operation of a stack constructed of such cells. The results of reversible cycling over 500 h (21 cycles) are compared with operating the cells under potentiostatic conditions in the electrolysis-only mode (i.e., without cycling). Voltage-current density (DC), AC complex impedance spectroscopy, distribution of relaxation times (DRT) analysis, and scanning electron microscopy (SEM) indicate excellent reversibility and stability of the neodymium nickelate-based oxygen electrodes in both electrolysis and reversible cycling modes. Degradation behavior is attributed to the loss and coarsening of connected Ni particles in the fuel electrode, particularly in the active layer. However, reversible operation mitigates this degradation compared to operation in the electrolysis-only (SOEC-only) mode.

25 ENERGY STORAGE↗

DOE OSTI2026

Radiation Damage Mechanisms in Oxide-Based Solid Electrolytes

Ion implantation is a promising approach to mitigate dendrite formation in metal anode solid-state batteries by modifying the chemical and mechanical properties of oxide-based electrolyte surfaces such as Li 7 La 3 Zr 2 O 12 (LLZO). Yet, the detailed atomistic mechanisms and potentially adverse side effects of ion implantation remain poorly understood. In this study, we used molecular dynamics simulations to elucidate the evolution of radiation-induced damage in LLZO. The results reveal that radiation damage is primarily driven by recoils from heavy ions in the lattice, producing antisite defect clusters whose density decreases as recoil energy increases, a counterintuitive finding that highlights complex cascade fragmentation. Radiation-induced disruption to the crystal sublattice connectivity, especially in the La–O network critical for Li-ion transport, leads to degradation in ionic pathways at low energies, while higher energy cascades can form new conduction pathways via enhanced Zr–O network connectivity. These findings provide a mechanistic foundation for optimizing ion implantation strategies that balance disruption of the lattice for surface modification for dendrite resistance with preservation of essential ionic conductivity.

Defects↗

DOE OSTI2022

Alkene adsorption and cracking on acidic zeolites – A gradual process of understanding

Cracking of light alkenes on solid acids and, in particular on zeolites, is ubiquitous in refineries. Different zeolite framework topologies in the catalysts used provide spatial constraints for reactants and products, leading to discrete reaction routes and varying selectivities. The conversion of alkenes in cracking proceeds either via monomolecular or bimolecular reaction pathways. In both routes, the reacting alkene adsorbs first on Brønsted acid sites forming the initial state (e.g., π-complex, carbenium ion or alkoxide), followed by β-cleavage in the carbenium transition state, generating a smaller alkene and a carbenium ion (monomolecular route) or forming a dimer by alkene addition that cracks subsequently (bimolecular route). The current state of understanding alkene sorption and cracking is critically discussed in this paper and four questions are formulated that may be the central questions from our perspective in further developing new generations of catalysts and processes for alkene conversion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

1 H chemical shift anisotropy: a high sensitivity solid-state NMR dynamics probe for surface studies?

We report dynamics play significant roles in chemistry and biochemistry-molecular motions impact both large- and small-scale chemical reactions in addition to biochemical processes. In many systems, including heterogeneous catalysts, the characterization of dynamics remains a challenge. The most common approaches involve the solid-state NMR measurement of anisotropic interactions, in particular 2 H quadrupolar coupling and 1 H–X dipolar coupling, which generally require isotope enrichment. Due to the high sensitivity of 1 H NMR, 1 H chemical shift anisotropy (CSA) is a particularly enticing, and underexplored, dynamics probe. We carried out 1 H CSA and 1 H– 13 C dipolar coupling measurements in a series of model supported complexes to understand how 1 H CSA can be leveraged to gain dynamic information for heterogeneous catalysts. Mathematical descriptions are given for the dynamic averaging of the CSA tensor, and its dependence on orientation and asymmetry. The variability of the orientation of the tensor in the molecular frame, in addition to its magnitude and asymmetry, negatively impacts attempts to extract quantitative dynamic information. Nevertheless, 1 H CSA measurements can reveal useful qualitative insights into the motions of a particularly dilute site, such as from a surface species.

1H chemical shift anisotropy↗

DOE OSTI2025

Deciphering the local structure of Prussian blue analogue cathodes with Raman spectroscopy for sodium-ion batteries

Iron-based Prussian blue analogues (PBAs) have gained attention as low-cost, relatively higher-potential cathodes for sodium-ion batteries, due to their open 3D-framework structures. However, understanding the local structural changes is critical to unveiling the intercalation pathways and degradation mechanisms. We employ here operando Raman spectroscopy to probe the changes in the cyanide vibrational modes during cycling and degradation after cycling, which are not adequately resolved by X-ray diffraction due to the low structure factor and limited X-ray sensitivity of the cyanide groups. Vibrational spectroscopy has thus proven essential for deciphering these complex materials. Additionally, we implement pre-sodiation strategies to assess the impact of sodium inventory loss by pairing PBAs with a hard carbon anode in a full-cell configuration. Operando galvanostatic electrochemical impedance spectroscopy (EIS) and ex situ X-ray photoelectron spectroscopy (XPS) further elucidate the interface evolution and the role of water molecules in forming the cathode-electrolyte interphase (CEI) and solid-electrolyte interphase (SEI). The insights gained advance the understanding of PBAs and enhance their practical viability.

25 ENERGY STORAGE↗

DOE OSTI2020

High Temperature Erosion In Particle Based CSP Systems

Particle based concentrated solar power plants are increasingly being considered as an alternative to molten salts. Although these particle based systems provide the inherent safety and enhanced lifetime from reduced corrosion compared to molten salt systems, they bring in complexities associated with surface erosion from falling particle impact and sliding motion along the surfaces. Past research on particle related erosion has been limited to high velocity applications and doesn’t necessarily coincide with the operating conditions in CSP systems. In our work, we evaluate characterize the rate of erosion for particles and containment materials at 800ºC. Three different types of erosion resulting from a) impact of solid particles on receiver, particle storage, and heat exchanger walls; b) abrasion erosion from particle sliding motion along walls; and c) attrition erosion as the particles breakdown from particle-to-particle contact and particle-to-wall interactions are evaluated and compared across a varied spectrum of particle and containment material spectrum. From the results, It is noted that temperature plays a key role in the rate of erosion experienced by any material. With the increase in temperature, materials become more ductile and are more readily sheared away from particle impinging or sliding motion. Furthermore, the particles themselves have higher susceptibility to breakdown which also lowers particle thermal absorptance and thus efficiency as heat transfer fluid.

14 SOLAR ENERGY↗

NASA NTRS1992

Forcing function effects on unsteady aerodynamic gust response. II - Low solidity airfoil row response

The paper investigates the fundamental gust modeling assumption on the basis of a series of experiments performed in the Purdue Annular Cascade Research Facility. The unsteady period flow field is generated by rotating flows of perforated plates and airfoil cascades, with the resulting unsteady periodic chordwise pressure response of a downstream low solidity stator row determined by miniature pressure transducers embedded within selected airfoils. When the forcing function exhibited the characteristics of a linear-theory gust, the resulting response on the downstream stator airfoils was in excellent agreement with the linear-theory models. When the forcing function did not exhibit linear-theory gust characteristics, the resulting unsteady aerodynamic response of the downstream stators was much more complex and correlated poorly with the linear-theory gust predictions. It is shown that the forcing function generator significantly affects the resulting gust response, with the complexity of the response characteristics increasing from the perforated-plate to the airfoil-cascade forcing functions.

Henderson, Gregory H.↗

NASA NTRS2000

Mars Exploration 2003 to 2013 - An Integrated Perspective: Time Sequencing the Missions

The science goals for the Mars exploration program, together with the HEDS precursor environmental and technology needs, serve as a solid starting point for re-planning the program in an orderly way. Most recently, the community has recognized the significance of subsurface sampling as a key component in "following the water". Accessing samples from hundreds and even thousands of meters beneath the surface is a challenge that will call for technology development and for one or more demonstration missions. Recent mission failures and concerns about the complexity of the previously planned MSR missions indicate that, before we are ready to undertake sample return and deep sampling, the Mars exploration program needs to include: 1) technology development missions; and 2) basic landing site assessment missions. These precursor missions should demonstrate the capability for reliable & accurate soft landing and in situ propellant production. The precursor missions will need to carry out close-up site observations, ground-penetrating radar mapping from orbit and conduct seismic surveys. Clearly the programs should be planned as a single, continuous exploration effort. A prudent minimum list of missions, including surface rovers with ranges of more than 10 km, can be derived from the numerous goals and requirements; they can be sequenced in an orderly way to ensure that time is available to feed forward the results of the precursor missions. One such sequence of missions is proposed for the decade beginning in 2003.

Briggs, G.↗

NASA NTRS2008

Miniature Mass Spectrometers on Space and Planetary Missions

Space flight mass spectrometers contribute our understanding of the origin and evolution of our solar system and even of life itself. This fundamental role has motivated increasing interest in miniature mass spectrometry for planetary missions. Several remarkable new instruments are en route or under development to investigate the composition of planetary bodies such as Mars and comets. For instance, the Sample Analysis at Mars (SAM) suite on the 2009 Mars Science Laboratory (MSL) mission includes a quadrupole mass spectrometer with a sophisticated gas processing system as well as pyrolysis and chemical derivatization protocols for solid samples. Future missions will require even lighter, lower power, and yet more capable mass spectrometers, particularly to analyze samples in situ on planetary surfaces. We have been developing laser-based mass spectrometers for elemental and organic/molecular analysis of rock, ice, or fine particle samples. These typically use time-of-flight (TOF) mass analyzers, which are readily miniaturized and can detect both atomic species and complex organics that occur in a variety of planetary materials. For example, nonvolatile polycyclic aromatic hydrocarbons and kerogen-like macromolecular carbon are found in some carbonaceous meteorites, which derived from asteroid parent bodies. A single focused laser pulse is able to volatilize and ionize some of these compounds for direct TOF analysis. While this is possible without any sample preparation or contact, sensitivity and quantitative performance can improve significantly with some sample handling. As such we have also been examining robotic mechanisms and protocols to accompany space flight mass spectrometers. In addition, sensors in early development may significantly improve these capabilities, via use of techniques such as switchable polarity, ambient pressure, or resonant ionization; tandem mass spectrometry (TOF or ion trap); and chemical imaging.

Brinckerhoff, William↗

DOE OSTI2020

High Temperature Erosion In Particle Based CSP Systems

Particle based concentrated solar power plants are increasingly being considered as an alternative to molten salts. Although these particle based systems provide the inherent safety and enhanced lifetime from reduced corrosion compared to molten salt systems, they bring in complexities associated with surface erosion from falling particle impact and sliding motion along the surfaces. Past research on particle related erosion has been limited to high velocity applications and doesn’t necessarily coincide with the operating conditions in CSP systems. In our work, we evaluate characterize the rate of erosion for particles and containment materials at 800ºC. Three different types of erosion resulting from a) impact of solid particles on receiver, particle storage, and heat exchanger walls; b) abrasion erosion from particle sliding motion along walls; and c) attrition erosion as the particles breakdown from particle-to-particle contact and particle-to-wall interactions are evaluated and compared across a varied spectrum of particle and containment material spectrum. From the results, It is noted that temperature plays a key role in the rate of erosion experienced by any material. With the increase in temperature, materials become more ductile and are more readily sheared away from particle impinging or sliding motion. Furthermore, the particles themselves have higher susceptibility to breakdown which also lowers particle thermal absorptance and thus efficiency as heat transfer fluid.

14 SOLAR ENERGY↗

NASA NTRS1997

The solid state environment orchestrates embryonic development and tissue remodeling

Cell interactions with extracellular matrix and with other cells play critical roles in morphogenesis during development and in tissue homeostasis and remodeling throughout life. Extracellular matrix is information-rich, not only because it is comprised of multifunctional structural ligands for cell surface adhesion receptors, but also because it contains peptide signaling factors, and proteinases and their inhibitors. The functions of these groups of molecules are extensively interrelated. In this review, three primary cell culture models are described that focus on adhesion receptors and their roles in complex aspects of morphogenesis and remodeling: the regulation of proteinase expression by fibronectin and integrins in synovial fibroblasts; the regulation of osteoblast differentiation and survival by fibronectin, and the regulation of trophoblast differentiation and invasion by integrins, cadherins and immunoglobulin family adhesion receptors.

NASA Discipline Musculoskeletal↗

DOE OSTI2023

Post Irradiation Examination Results of Irradiated Yttrium Hydride

Department of Energy’s (DOE’s) Microreactor program (MRP) aims to provide the fundamental data to enable the development of microreactors. As such, material property data of critical materials for microreactor technologies are researched. Because substoichiometric yttrium dihydride (YHx, where x<2) is considered as a potential solid neutron moderator, its material property data has been combined in the Advanced Moderator Material Handbook which includes thermodynamic and thermophysical properties of YHx with the exception of irradiated material’s properties due to limited PIE. To fill the knowledge gap for the irradiated YHx, specimens and irradiation capsules were prepared at Los Alamos National Laboratory (LANL). Specimens were irradiated in the Advanced Test Reactor (ATR) at Idaho National Laboratory’s (INL’s). post-irradiation examination (PIE) was performed at INL’s Materials and Fuels Complex (MFC). This report compiles the PIE results of irradiated YHx specimens through fiscal years 2022 and 2023 (FY22-23) . The PIE data will directly be incorporated into the newer version of the Advanced Moderator Material Handbook. The main takeaways include that (i) the geometrical stability and mechanical integrity of YHx was intact with couple exceptions after high-temperature irradiations (600-800°C), (ii) hydrogen content variation due to manufacturing or irradiation in YHx caused visible surface discoloration, that is also related to the microstructural changes, (iii) qualitative comparisons of PIE methods implied that H retention was significantly higher at 600°C as compared to 800°C, (iv) thermal properties included signatures correlated with the H loss or re-gain, (v) importance of manufacturing readiness and initial as-manufactured specimens history was emphasized, (vi) the needs of targeted irradiations focusing on temperature and time parameters and very targeted PIE were specified.

08 HYDROGEN↗

DOE OSTI2023

Report on the Incorporation of Post-Irradiation Examination Results of Yttrium Hydride for Advanced Moderator Handbook

Department of Energy’s (DOE’s) Microreactor program (MRP) aims to provide the fundamental data to enable the development of microreactors. As such, material property data of critical materials for microreactor technologies are researched. Because substoichiometric yttrium dihydride (YHx, where x<2) is considered as a potential solid neutron moderator, its material property data has been combined in the Advanced Moderator Material Handbook which includes thermodynamic and thermophysical properties of YHx with the exception of irradiated material’s properties due to limited PIE. To fill the knowledge gap for the irradiated YHx, specimens and irradiation capsules were prepared at Los Alamos National Laboratory (LANL). Specimens were irradiated in the Advanced Test Reactor (ATR) at Idaho National Laboratory’s (INL’s). post-irradiation examination (PIE) was performed at INL’s Materials and Fuels Complex (MFC). This report compiles the PIE results of irradiated YHx specimens through fiscal years 2022 and 2023 (FY22-23) . The PIE data will directly be incorporated into the newer version of the Advanced Moderator Material Handbook. The main takeaways include that (i) the geometrical stability and mechanical integrity of YHx was intact with couple exceptions after high-temperature irradiations (600-800°C), (ii) hydrogen content variation due to manufacturing or irradiation in YHx caused visible surface discoloration, that is also related to the microstructural changes, (iii) qualitative comparisons of PIE methods implied that H retention was significantly higher at 600°C as compared to 800°C, (iv) thermal properties included signatures correlated with the H loss or re-gain, (v) importance of manufacturing readiness and initial as-manufactured specimens history was emphasized, (vi) the needs of targeted irradiations focusing on temperature and time parameters and very targeted PIE were specified.

08 HYDROGEN↗

DOE OSTI2020

Rapid Viscoelastic Deformation Slows Marine Ice Sheet Instability at Pine Island Glacier

The ice sheets of the Amundsen Sea Embayment (ASE) are vulnerable to the marine ice sheet instability (MISI), which could cause irreversible collapse and raise sea levels by over a meter. The uncertain timing and scale of this collapse depend on the complex interaction between ice, ocean, and bedrock dynamics. The mantle beneath the ASE is likely less viscous (~10 18 Pa s) than the Earth's average mantle (~10 21 Pa s). In this paper we show that an effective equilibrium between Pine Island Glacier's retreat and the response of a weak viscoelastic mantle can reduce ice mass lost by almost 30% over 150 years. Other components of solid Earth response—purely elastic deformations and geoid perturbations—provide less stability than the viscoelastic response alone. Uncertainties in mantle rheology, topography, and basal melt affect how much stability we expect, if any. Our study indicates the importance of considering viscoelastic uplift during the rapid retreat associated with MISI.

54 ENVIRONMENTAL SCIENCES↗