SEARCH · Engineering Papers

Results for “Air Sampling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,657 records · Page 92

All sources NASA NTRS DOE OSTI

DOE OSTI2015

Influence of Yb{sub 2}O{sub 3} on electrical and microstructural characteristics of CaCu{sub 3}Ti{sub 4}O{sub 12} ceramics

Graphical abstract: Some Yb atoms entered in the lattice of CCTO substituted the Ca sites, the rest of Yb atoms concentrated at grain boundaries decreased the grain size. The dielectric constant was decreased by Yb doping. The dielectric loss of the CCTO could be greatly reduced at low frequency. - Highlights: • Yb atoms may take the place of Ca sites and concentrate at grain boundaries. • Tiny second phase corresponding to Yb may decrease the grain size. • Decrease of the grain size leads to the decrease of dielectric constant. • Yb doping could decrease the dielectric loss of CCTO. - Abstract: This paper focuses on the remarkable effects of Yb{sub 2}O{sub 3} doping on the microstructure and dielectric characteristics of CaCu{sub 3}Ti{sub 4}O{sub 12} (CCTO). Samples were prepared by the solid phase reaction method and sintered in air at 1030 °C for 12 h. X-ray diffraction and X-ray photoelectron spectroscopy studies confirm that the primary phase is CCTO. Some Yb{sup 3+} ions may substitute into the Ca site at the center or zenith sites of the CCTO lattice hexahedron, while the rest of the Yb atoms may concentrate at grain boundaries. The grain size of Yb{sub 2}O{sub 3}-doped CCTO ceramics were examined by scanning electron microscopy and demonstrate sharp grain size reduction with Yb{sub 2}O{sub 3} doping. From dielectric property measurements, the Yb{sub 2}O{sub 3} doping reduces the dielectric constant of CCTO, and the dielectric loss is also reduced.

36 MATERIALS SCIENCE↗

DOE OSTI2018

Low cost and facile fabrication of broadband laser power meter based on reduced graphene oxide film

Highlights: • The reduced graphene oxide film is used to fabricate the low cost laser powermeter. • The photoresponse of the device is explored in the visible to near-infrared range. • The photoresponse of the device is linearly related to the irradiated laser power. • The photoelectric current of the device does not depend on the laser spot size. - Abstract: Here, we have demonstrated a new type of broadband reduced graphene oxide-based laser power meter in simple and low cost method. The broadband photosensitivity of the device is confirmed by photocurrent measurements at different incident laser wavelengths of 405, 532, 635 and 808 nm. It is shown that its photocurrent increases linearly with increasing the power of the laser beam. Also, it is observed that the photocurrent behavior of the device does not depend upon the size of the laser spot. It should be noted that the reduced graphene oxide power meter is the thermal detection device. Therefore, the response of the sample in the vacuum is greatly enhanced in compared to the environmental air. Cooling system can also decrease the time required for the establishment of thermal equilibrium and thus reduce the response time of the power meter. These results open up exciting opportunities for developing broadband photodetectors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2021

The use of a digital micromirror array as a temporal gate and spatial-filtering device for laser-induced breakdown spectroscopy and laser ablation molecular isotopic spectrometry

A digital micromirror array (DMMA) is used in a simple and inexpensive approach for spatially resolved temporal gating of atomic emission detection in laser-induced breakdown spectroscopy (LIBS). Selected mirrors in the array are actuated at a time delayed from the primary laser pulse, permitting optical gating with a response time of 160 ns while using a conventional CCD detector. Detector gating is shown to decrease noise from short-lived spectroscopic background (both continuum and N II from air), improving signal-to-background ratios by 22-times for selected samples and emission lines. The utility of rapid temporal gating is also demonstrated for the optical detection of isotopes using the laser-ablation molecular isotope spectrometry (LAMIS) experiment. Additionally, optical temporal gating and spatial filtering are used to isolate regions of the laser-induced plasma, enhancing signal from molecular emission. The potential of the simple technique for use in field-portable LIBS and LAMIS experiments is explored.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2022

Visualization of defect induced in-gap states in monolayer MoS 2

Atomic-scale intrinsic defects play a key role in controlling functional electronic properties of two-dimensional (2D) materials. Here, we present a low-temperature scanning–tunneling microscopy and spectroscopy investigation of a common point-defect in monolayer molybdenum disulfide (MoS 2 ). We employ a sample preparation method in which the film surface is never exposed to air so that the native dangling bonds surrounding the defects in the film are preserved. Molybdenum vacancies are identified by their three characteristic in-gap resonances by combining scanning–tunneling measurements with parallel Green’s function-based theoretical modeling. The relative energy shifts between the various in-gap states allow us to identify a relative charge difference between two of the observed vacancies. The role of the substrate on the band structure of the defective MoS 2 monolayer is unveiled. Our study highlights the effects of the substrate on the in-gap states of common defects found in MoS 2 providing a pathway in designing and optimizing 2D materials for electronic applications.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Distinguishing photo-induced oxygen attack on alkyl chain versus conjugated backbone for alkylthienyl-benzodithiophene (BDTT)-based push–pull polymers

Synthetic design has enabled increasing power conversion efficiency advances in organic photovoltaics (OPV). One continuing knowledge gap is detailed understanding of single-material chemical (photo)stability. Many considerations are based on prior OPV-relevant donor homopolymer systems rather than the next-generation push–pull architectures. Generally, energetic offsets between the lowest occupied molecular orbital of the donor and molecular oxygen are assumed to dictate kinetics of photo-induced charge transfer to a super oxide radical. Herein we determine the ambient-induced photo-degradation pathways, presented as proposed site-specific arrow-pushing mechanisms, for five donor polymers all containing the same push unit – alkylthienyl-substituted-benzodithiophene (BDTT) – but with chemically distinct pull units. The donor-only polymer films were subject to controlled photobleaching in air as an accelerated degradation approach, coupled with simultaneous monitoring of absorptance. Sample subsets were periodically removed and analyzed with X-ray photoelectron spectroscopy, to evaluate near-surface chemical composition and oxygen additions to hetero reporter atoms on either the BDTT push unit or distinct pull unit (i.e., sulphur and nitrogen). Here, this methodology allows us to distinguish between different mechanisms of bond cleavage and formation. Overall, we find that neither polymer redox properties nor individual push or pull unit stability are sufficient to predict photo-oxidative degradation of these polymers. Rather, there is a greater dependence on the susceptibility of unique structural groups within a polymeric system. Alkyl chain oxygen addition is generally the first attack site and direct sulfur oxidation on the conjugated backbone occurs after saturation of the alkyl chain initiation sites. This work provides a standard that could be used to evaluate relative photo-oxidative (in)stability for new OPV materials quickly – prior to time-consuming device optimization – and demonstrates an effective methodology for correlating optical degradation with chemical structure alterations via spectroscopic signatures to guide synthetic design.

14 SOLAR ENERGY↗

DOE OSTI2014

Growth of silicon quantum dots by oxidation of the silicon nanocrystals embedded within silicon carbide matrix

A moderately low temperature (≤800 °C) thermal processing technique has been described for the growth of the silicon quantum dots (Si-QD) within microcrystalline silicon carbide (μc-SiC:H) dielectric thin films deposited by plasma enhanced chemical vapour deposition (PECVD) process. The nanocrystalline silicon grains (nc-Si) present in the as deposited films were initially enhanced by aluminium induced crystallization (AIC) method in vacuum at a temperature of T{sub v} = 525 °C. The samples were then stepwise annealed at different temperatures T{sub a} in air ambient. Analysis of the films by FTIR and XPS reveal a rearrangement of the μc-SiC:H network has taken place with a significant surface oxidation of the nc-Si domains upon annealing in air. The nc-Si grain size (D{sub XRD}) as calculated from the XRD peak widths using Scherrer formula was found to decrease from 7 nm to 4 nm with increase in T{sub a} from 250 °C to 800 °C. A core shell like structure with the nc-Si as the core and the surface oxide layer as the shell can clearly describe the situation. The results indicate that with the increase of the annealing temperature in air the oxide shell layer becomes thicker and the nc-Si cores become smaller until their size reduced to the order of the Si-QDs. Quantum confinement effect due to the SiO covered nc-Si grains of size about 4 nm resulted in a photoluminescence peak due to the Si QDs with peak energy at 1.8 eV.

36 MATERIALS SCIENCE↗

DOE OSTI2014

Conditionally Rare Taxa Disproportionately Contribute to Temporal Changes in Microbial Diversity

Microbial communities typically contain many rare taxa that make up the majority of the observed membership, yet the contribution of this microbial “rare biosphere” to community dynamics is unclear. Using 16S rRNA amplicon sequencing of 3,237 samples from 42 time series of microbial communities from nine different ecosystems (air; marine; lake; stream; adult human skin, tongue, and gut; infant gut; and brewery wastewater treatment), we introduce a new method to detect typically rare microbial taxa that occasionally become very abundant (conditionally rare taxa [CRT]) and then quantify their contributions to temporal shifts in community structure. We discovered that CRT made up 1.5 to 28% of the community membership, represented a broad diversity of bacterial and archaeal lineages, and explained large amounts of temporal community dissimilarity (i.e., up to 97% of Bray-Curtis dissimilarity). Most of the CRT were detected at multiple time points, though we also identified “one-hit wonder” CRT that were observed at only one time point. Using a case study from a temperate lake, we gained additional insights into the ecology of CRT by comparing routine community time series to large disturbance events. Our results reveal that many rare taxa contribute a greater amount to microbial community dynamics than is apparent from their low proportional abundances. In conclusion, this observation was true across a wide range of ecosystems, indicating that these rare taxa are essential for understanding community changes over time.

59 BASIC BIOLOGICAL SCIENCES↗

NASA NTRS1972

Determination of Optical Constants of in Bi from Reflectance Measurements

A fall in reflectance was noted from values obtained for a freshly cleaved sample to values obtained after periods of exposure of the surface to air. The decrease in reflectance with increased exposure time is attributed to formation of a surface layer insoluble in Freon or ethyl alcohol; it is assumed to be a tarnish layer. Computer processing was employed to calculate optical constants from reflectance data.

Martin, F. E.↗

NASA NTRS1974

Water quality by photographic analysis

Positive correlation exists between reflectance of water and the water quality parameter of turbidity. This relationship holds for all times for a particular waste. At particular times other parameters such as suspended solids correlate to turbidity and can also be mapped. To analyze aerial photos properly to obtain water reflectance, a standard reflectance panel is needed somewhere in the frame. For this study color and color-infrared film are used and analyzed with a color microdensitometer which, with certain modifications, is also used to analyze reflectance of water samples. Noise in the analysis includes bottom effects, reflection from the air-water interface, and path luminance, but these can all be dealt with by proper techniques.

Klooster, S. A.↗

NASA NTRS1985

Accurate Airborne Particle Sampler

Air inducted isokinetically into centrifugal collector. Cloud drop collector accurately and efficiently samples droplets and rejects aerosol particles. Number of these collectors connected in series, each designed that largest size fraction of droplets captured in first one and successively smaller size fractions captured in others. By analyzing each size fraction, chemical composition of cloud droplets related to drop size.

Miller, I. M.↗

NASA NTRS1986

An evaluation of candidate oxidation resistant materials for space applications in LEO

Ground based testing of materials considered for polyimide (Kapton) solar array blanket protection and graphite-epoxy stroctural member protection was performed in an RF plasma asher. Protective coatings on Kapton from various commercial sources and from NASA Lewis Research Center were exposed to the air plasma; and mass loss per unit area was measured for each sample. All samples evaluated provided some protection to the underlying surface, but metal-oxide-fluoropolymer coatings provided the best protection by exhibiting very little degradation after 47 hr of asher exposure. Mica paint was evaluated as a protective coating for graphite-epoxy structural members. Mica appeared to be resistant to attack by atomic oxygen, but only offered limited protection as a paint. this is believed to be due to the paint vehicle ashing underneath the mica leaving unattached mica flakes lying on the surface. The protective coatings on Kapton evaluated so far are promising but further research on protection of graphite-epoxy support structures is needed.

Rutledge, Sharon↗

NASA NTRS1987

A prediction method for flow in the Shuttle tile strain isolation pad

The Shuttle Orbiter thermal protection system uses a Strain Isolation Pad (SIP) between the tile and the Orbiter. This paper presents experimental measurements of the pressure drop and associated flow rate through a sample of the SIP material. Included are data for a range of air densities representative of Shuttle ascent and re-entry trajectories. Also presented are new theoretical and correlative methods which predict the experimental data. These methods will help in predicting venting characteristics of tile assemblies during ascent, and hot gas leak under the tiles during descent. The predictive philosophy developed is useful in the study of fibrous and porous media fluid mechanics.

Lawing, Pierce L.↗

NASA NTRS1988

Imaging graphite in air by scanning tunneling microscopy - Role of the tip

Atomically resolved images of highly oriented pyrolytic graphite (HOPG) in air at point contact have been obtained. Direct contact between tip and sample or contact through a contamination layer provides a conduction mechanism in addition to the exponential tunneling mechanism responsible for scanning tunneling microscopy (STM) imaging. Current-voltage (I-V) spectra were obtained while scanning in the current imaging mode with the feedback circuit interrupted in order to study the graphite imaging mechanism. Multiple tunneling tips are probably responsible for images without the expected hexagonal or trigonal symmetry. The observations indicate that the use of HOPG for testing and calibration of STM instrumentation may be misleading.

Colton, R. J.↗

NASA NTRS1990

Analysis of pressure-broadened ozone spectra in the 3 micron region

The Molecular Spectroscopy Lab at NASA-Langley has been involved in a long term effort to carefully characterize the infrared spectra of small molecules of atmospheric interest, including methane, water vapor, ozone, and their isotopic counterparts. High resolution gas phase infrared spectra are obtained using both a tunable diode laser system, and the McMath Fourier transform spectrometer at the Kitt Peak Solar Observatory. Spectra are obtained at various pressures and temperatures for pure gas samples, and for samples containing mixtures of the species of interest in nitrogen, oxygen, or air. From these spectra, using a nonlinear least squares fitting technique, spectral parameters of position, intensity, and half-width were determined for varying laboratory conditions that approximate atmospheric conditions experienced in remote sensing situations. These parameters are of interest in theoretical studies of these species, as well as in allowing more accurate interpretation of remote sensing data. The current work involves the analysis of a series of McMath FTIR spectra of ozone broadened by mixing with air, nitrogen, or oxygen. Each spectrum covers the region from 2396 to 4057/cm. Each vibrational band is analyzed by first diving its region into small intervals containing a few well isolated absorption lines of reasonable intensity. Each of these small intervals is fit by multiple iterations of the nonlinear least square program until residuals are minimized to a reasonable value which corresponds to the noise level of the measured spectrum. Intervals for the 3 nu(sub 3) ozone band in the region from 3000 to 3060 wavenumbers are being examined.

Prochaska, Eleanor S.↗

NASA NTRS1991

An observational and theoretical study of highly supercooled altocumulus

The microphysics of two altocumulus clouds sampled at a temperature of about -30 C through the NCAR King Air aircraft and coincident lidar has been characterized. The clouds are structurally similar to stratocumulus and have extensive cloudtop entrainment, a capping temperature inversion, and a dry layer above. Microphysical and radiative properties of both clouds have been modeled numerically. When entrainment effects are incorporated in the model, calculations of droplet concentration and mean diameter profiles compare favorably with the measurements. Radiative transfer calculations indicate that radiative cooling causes sufficient negative buoyancy in cloudtop parcels for producing convective instability and reproducing the observed downdraft velocities. It is shown that entrainment of warmer, drier air near a cloudtop counteracts the radiatively induced negative buoyancy in the downdrafts.

Heymsfield, Andrew J.↗

NASA NTRS1997

10,000-Hour Cyclic Oxidation Behavior at 982 C (1800 F) of 68 High-Temperature Co-, Fe-, and Ni-Base Alloys

Sixty-eight high temperature Co-, Fe-, and Ni-base alloys were tested for 10-one thousand hour cycles in static air at 982 C (1800 F). The oxidation behavior of the test samples was evaluated by specific weight change/time data, x-ray diffraction of the post-test samples, and their final appearance. The gravimetric and appearance data were combined into a single modified oxidation parameter, KB4 to rank the cyclic oxidation resistance from excellent to catastrophic. The alloys showing the 'best' resistance with no significant oxidation attack were the alumina/aluminate spinel forming Ni-base turbine alloys: U-700, NASA-VIA and B-1900; the Fe-base ferritic alloys with Al: TRW-Valve, HOS-875, NASA-18T, Thermenol and 18SR; and the Ni-base superalloy IN-702.

Barrett, Charles A.↗

NASA NTRS2004

Aviation Particle Emissions Workshop

The Aviation Particle Emissions Workshop was held on November 18 19, 2003, in Cleveland, Ohio. It was sponsored by the National Aeronautic and Space Administration (NASA) under the Vehicle Systems Program (VSP) and the Ultra- Efficient Engine Technology (UEET) Project. The objectives were to build a sound foundation for a comprehensive particulate research roadmap and to provide a forum for discussion among U.S. stakeholders and researchers. Presentations included perspectives from the Federal Aviation Administration, the U.S. Environmental Protection Agency, NASA, and United States airports. There were five interactive technical sessions: sampling methodology, measurement methodology, particle modeling, database, inventory and test venue, and air quality. Each group presented technical issues which generated excellent discussion. The five session leads collaborated with their members to present summaries and conclusions to each content area.

Wey, Chowen C.↗

NASA NTRS1993

Process for producing a high emittance coating and resulting article

Process for anodizing aluminum or its alloys to obtain a surface particularly having high infrared emittance by anodizing an aluminum or aluminum alloy substrate surface in an aqueous sulfuric acid solution at elevated temperature and by a step-wise current density procedure, followed by sealing the resulting anodized surface. In a preferred embodiment the aluminum or aluminum alloy substrate is first alkaline cleaned and then chemically brightened in an acid bath The resulting cleaned substrate is anodized in a 15% by weight sulfuric acid bath maintained at a temperature of 30.degree. C. Anodizing is carried out by a step-wise current density procedure at 19 amperes per square ft. (ASF) for 20 minutes, 15 ASF for 20 minutes and 10 ASF for 20 minutes. After anodizing the sample is sealed by immersion in water at 200.degree. F. and then air dried. The resulting coating has a high infrared emissivity of about 0.92 and a solar absorptivity of about 0.2, for a 5657 aluminum alloy, and a relatively thick anodic coating of about 1 mil.

Le, Huong G.↗