Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “safety testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Step-loaded creep testing of Zircaloy-4 cladding at higher temperatures in the α-phase

A refined understanding of zirconium-based cladding thermomechanical performance during rapid transients is essential for enhancing the safety and operation of light-water reactors. Traditional models for zirconium alloys under accident conditions generally assume that creep dominates fuel cladding performance. Here, these historic models have largely remained unchanged and serve as the basis for safety criteria development. As the U.S. nuclear industry pursues higher burnup levels, the increased release of fission gases during transients raises the risk of cladding failure in the low-temperature hcp α-phase, making the fidelity of these models of greater importance. Creep testing was conducted from 550–700°C with 25–120 MPa applied hoop stresses to investigate Zircaloy-4 deformation at accident-relevant temperatures in the α-phase. Step-loading was employed to capture creep behavior across a wide stress range from a single sample. The stress-strain rate data at higher temperatures (650 and 700°C) were well-described by isotropic versions of the Erbacher and Kaddour models, while the lower temperature data (550 and 600°C) were underpredicted by both anisotropic and isotropic model variants. Greater strain rates during the initial loading step at 650 and 700°C were attributed to recrystallization and grain growth of sub-micron crystallites. Yet, texture analysis revealed the basal split texture remained after testing. These observations produced results suggesting Zircaloy-4 claddings experience higher creep rates across the α-phase than previously thought, possibly related to dynamic anisotropy due to temperature dependent activation of deformation mechanisms, effects of biaxial loading, and variation in material condition between the current testing used in previous model development.

36 MATERIALS SCIENCE↗
NASA NTRS2018

New Sensors and Techniques for Aircraft Engine Health Monitoring

The ability to monitor the health of the rotating components in aircraft engines is of major interest to aero community in improving safety and reliability. The use of instrumentation for these applications remains very challenging. It requires sensors and techniques that are highly accurate, able to operate in a high temperature environment, and sensitive enough to detect minute changes and hidden flaws before undesired events occur. The National Aeronautics and Space Administration (NASA), through several Aviation Safety Programs, has taken a leadership role in the development of new sensor technologies and techniques for the in-situ health monitoring of aircraft turbine engines. Along with the development of new instrumentation for aircraft engines, the Glenn Research Center has a diverse set of ground test facilities that are used to simulate the conditions that a vehicle would see in flight allowing new concepts to be safely developed and evaluated on the ground before progressing to actual flight. In this presentation Mark will give an overview of the NASA Glenn Research Center, discuss its past aviation safety initiatives, present some select sensors that have been developed for aircraft engine safety, and then conclude with some new measurement techniques that have been developed for use at the NASA Glenn test facilities, enabling better measurement and simulation of flight conditions. He will discuss current research and development efforts that he is working on at the NASA Glenn Research Center in the areas of new sensors and techniques for aircraft engine health monitoring. This work is being conducted in support of aviation safety.

Turbine↗
NASA NTRS1986

Aerospace Safety Advisory Panel report to the NASA acting administrator

The level of activity of the Aerospace Safety Advisory Panel was increased smewhat during 1985 in concert with the increased mission rate of the National Space Transportation System, the evolutionary changes in management and operation of that program, and the preparation of the Vandenberg Launch Site; the implementation of the Program Definition Phase of the Space Station Program; and the actual flight testing of the X-29 research aircraft. Impending payload STS missions and NASA's overall aircraft operations are reviewed. The safety aspects of the LEASAT salvage mission were assessed. The findings and recommendation of the committee are summerized.

Source record↗
NASA NTRS2017

Thermal Considerations for Reducing the Cooldown and Warmup Duration of the James Webb Space Telescope OTIS Cryo-Vacuum Test

The James Webb Space Telescope (JWST), set to launch in 2018, is NASAs next-generation flagship telescope. The Optical Telescope Element (OTE) and Integrated Science Instrument Module (ISIM) contain all of the optical surfaces and instruments to capture and analyze the telescopes infrared targets. The integrated OTE and ISIM are denoted as OTIS, and will be tested as a single unit in a critical thermal-vacuum test in mid-2017 at NASA Johnson Space Centers Chamber A facility. The payload will be evaluated for workmanship and functionality in a 20K simulated flight environment during this thermal-vacuum test. However, the sheer thermal mass of the OTIS payload as well as the restrictive gradient, rate, and contamination-related constraints placed on test components precludes rapid cooldown or warmup to its steady-state cryo-balance condition. Hardware safety considerations precludes injection of helium gas for free molecular heat transfer. Initial thermal analysis predicted that transient radiative cooldown from ambient temperatures, while meeting all limits and constraints, would take 33.3 days; warmup similarly would take 28.4 days. This paper discusses methods used to reduce transition times from the original predictions through modulation of boundary temperatures and environmental conditions. By optimizing helium shroud transition rates and heater usage, as well as rigorously re-examining previously imposed constraints, savings of up to three days on cooldown and up to a week on warmup can be achieved. The efficiencies gained through these methods allow the JWST thermal test team to create faster cooldown and warmup profiles, thus reducing the overall test duration and cost, while keeping all of the required test operations.

Thermal↗
NASA NTRS2017

Thermal Considerations for Reducing the Cooldown and Warmup Duration of the James Webb Space Telescope OTIS Cryo-Vacuum Test

The James Webb Space Telescope (JWST), set to launch in 2018, is NASAs next-generation flagship telescope. The Optical Telescope Element (OTE) and Integrated Science Instrument Module (ISIM) contain all of the optical surfaces and instruments to capture and analyze the telescopes infrared targets. The integrated OTE and ISIM are denoted as OTIS, and will be tested as a single unit in a critical thermal-vacuum test in mid-2017 at NASA Johnson Space Centers Chamber A facility. The payload will be evaluated for workmanship and functionality in a 20K simulated flight environment during this thermal-vacuum test. However, the sheer thermal mass of the OTIS payload as well as the restrictive gradient, rate, and contamination-related constraints placed on test components precludes rapid cooldown or warmup to its steady-state cryo-balance condition. Hardware safety considerations precludes injection of helium gas for free molecular heat transfer. Initial thermal analysis predicted that transient radiative cooldown from ambient temperatures, while meeting all limits and constraints, would take 33.3 days; warmup similarly would take 28.4 days. This paper discusses methods used to reduce transition times from the original predictions through modulation of boundary temperatures and environmental conditions. By optimizing helium shroud transition rates and heater usage, as well as rigorously re-examining previously imposed constraints, savings of up to three days on cooldown and up to a week on warmup can be achieved. The efficiencies gained through these methods allow the JWST thermal test team to create faster cooldown and warmup profiles, thus reducing the overall test duration and cost, while keeping all of the required test operations.

JWST↗
DOE OSTI2023

Progress Towards the Reality of Low-Temperature Critical Experiments with Low-Temperature TEX

Integral benchmarks for criticality safety do not exist below room temperature. Incredible support for below room temperature benchmarks is present across the international community. Validation of low-temperature neutron cross sections is necessary to verify any operation at temperatures below room temperature which is typically observed in environments far from the equator. For example, a fissile material transportation truck may routinely observe ambient temperatures down to -40°C, which is the lower temperature bound of the normal conditions of transportation defined in the United States Title 10 Code of Federal Regulations §71.71c2. Similarly, the IAEA, which contains 176 member states, has the same requirement for subcriticality for fissile material transportation. Additionally, sub-room temperature benchmarks can validate newly produced cross sections, that include novel thermal scattering laws, from North Carolina State University. A six-case experiment designed based off the TEX-HEU baseline experiments has been proposed utilizing a chilled vacuum chamber capable of cooling the HEU stack down to -50°C. The six proposed configurations span the entire neutron fission energy range and can be tested at intermediate temperatures between room temperature and -40°C. Of the six configurations, the fastest case utilizes nearly 135 kg of HEU. Understanding the system is required prior to critical experiment operations. In order to test the functionality of the system, testing with surrogate fuel materials has been conducted. The following discusses the design of the low temperature TEX (LT-TEX) experiment as well as the progress made via surrogate testing towards a reality in which low-temperature integral benchmarks exist in the International Criticality Safety Benchmark Evaluation Project (ICSBEP).

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS2020

Design and Analysis of Buckling-Critical Large-Scale Sandwich Composite Cylindrical Test Articles

It has long been established in the literature that the buckling response of thin-shell structures can be very sensitive to the presence of small geometric and loading imperfections. The Shell Buckling Knockdown Factor Project (SBKF) was established by the NASA Engineering and Safety Center (NESC) to develop analysis-based shell buckling design recommendations for stiffened-metallic and composite launch-vehicle shell structures. Large-scale buckling tests were used to validate the modeling and analysis methods applied in developing these analysis-based recommendations. Herein, the test article design methodology for 8-ft-diameter, honeycomb-core sandwich composite cylinder validation tests is discussed and cylinder designs are presented. In this methodology, first, the sandwich composite design space was defined using several nondimensional parameters, and the desired test article design space was determined by examining the designs of launch-vehicle cylinder structures. Essentially all test article designs within certain design parameters were generated and then downselected based on simple closed-form failure calculations and the nondimensional design-space parameters. Four of these designs that spanned a significant portion of the design space of interest and had global buckling as the first predicted failure mode were selected and subjected to higher-fidelity finite element analyses (FEAs): shell-element-based analyses, axisymmetric-element-based analyses, and global-local analyses. The analysis flow discussed in this report supported the design objective. As the analysis flow progressed, designs were downselected so the fidelity of the analysis methods, and consequently their computational cost and accuracy, was increased. The selection of the FEA types created an analysis framework where particular methods complemented each other and reduced the uncertainty of the predicted test article responses. The analysis results are illustrated using several designs when the computationally expeditious closed-form analysis stage is discussed. Once this stage is complete, the higher-fidelity FEA types are illustrated using one selected detailed test article design. Both perfect and imperfect test article geometries were considered.

Buckling↗
DOE OSTI2020

Testing of Crystalline Silicotitanate to Support Tank-Side Cesium Removal System Operations - 20458

The direct feed of waste from the Hanford tank farms to the Low-Activity Waste Facility at the Hanford Waste Treatment and Immobilization Plant requires an intermediate treatment step that prepares the waste for vitrification. Washington River Protection Solutions (WRPS) selected a near-tank treatment system known as the Tank-Side Cesium Removal (TSCR) system to perform the required intermediate treatment functions. The approach in the TSCR system is to filter waste supernatant with a sintered metal dead-end filter and then use a series of ion exchange columns to remove cesium; this system has several similarities to the Tank Closure Cesium Removal system that has been deployed on the Savannah River Site. The ion exchange media proposed for use is crystalline silicotitanate (CST), which is a non-elutable media with a high affinity for cesium. Because the media is non-elutable, loaded columns will be blown down with compressed air, moved into interim storage, and replaced with new columns when cesium capacity is reached. The assumed extent and rate of drying that could be achieved in the TSCR column geometry lacked confirmation by experimental data. In addition, once the columns are loaded with cesium, they generate flammable gases (primarily hydrogen) via radiolysis acting on any resident liquids, i.e., moisture, remaining in the media bed. An assessment of available information on CST concluded that gas generation data that bounds expected operational conditions were needed to support the TSCR system safety basis and planned operations. Working with WRPS, Pacific Northwest National Laboratory (PNNL) designed and conducted testing with CST media to address the need for (a) representative in-column drying data, and (b) bounding flammable gas generation data. Drying testing was performed using a full-height column with a diameter of approximately 2 inches with injected air at temperatures of 18 deg. C and 30 deg. C. Gas generation testing was conducted in an engineered bunker that allowed simultaneous irradiation of up to eight samples at a time. These two experimental approaches used at PNNL for the CST testing are summarized and the major outcomes are presented. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS2024

A Method of Compliance for Achieving Target Collision Risk in UTM Operations

This work proposes a method of compliance to ensure that the collision risks among small unmanned aircraft systems meet the target level of safety. This method presents what is needed for a strategic conflict detection service to achieve the target level of safety when conflict between operational intents are not permitted in nominal situations. A volume-based collision risk model is first developed to calculate the UA-to-UA collision risk given any two operational intent volumes. With this collision risk model, a test strategy is then proposed to assess if a strategic conflict detection service can reduce the collision risk and meet the target level of safety. The method also specifies operational data that are required to be collected to verify if requirements on conformance are being met. Additionally, two new requirements are identified and proposed by this method beyond the current standard for strategic conflict detection. In the sensitivity analysis, three main factors contributing to the collision risk are investigated. The analysis shows that buffers should be considered in a strategic conflict detection service when deconflicting operational intents. The results also reveal that the selection of test cases plays an important role in evaluating the strategic conflict detection service, and they should be representative and sufficiently complex in evaluation tests.

Collision Risk↗
NASA NTRSDate not supplied

A Method of Compliance for Achieving Target Collision Risk in UTM Operations

This work proposes a method of compliance to ensure that the collision risks among small unmanned aircraft systems meet the target level of safety. This method presents what is needed for a strategic conflict detection service to achieve the target level of safety when conflict between operational intents are not permitted in nominal situations. A volume-based collision risk model is first developed to calculate the UA-to-UA collision risk given any two operational intent volumes. With this collision risk model, a test strategy is then proposed to assess if a strategic conflict detection service can reduce the collision risk and meet the target level of safety. The method also specifies operational data that are required to be collected to verify if requirements on conformance are being met. Additionally, two new requirements are identified and proposed by this method beyond the current standard for strategic conflict detection. In the sensitivity analysis, three main factors contributing to the collision risk are investigated. The analysis shows that buffers should be considered in a strategic conflict detection service when deconflicting operational intents. The results also reveal that the selection of test cases plays an important role in evaluating the strategic conflict detection service, and they should be representative and sufficiently complex in evaluation tests.

UTM, Method of Compliance, collision risk↗
NASA NTRSDate not supplied

A Method of Compliance for Achieving Target Collision Risk in UTM Operations

This work proposes a method of compliance to ensure that the collision risks among small unmanned aircraft systems meet the target level of safety. This method presents what is needed for a strategic conflict detection service to achieve the target level of safety when conflict between operational intents are not permitted in nominal situations. A volume-based collision risk model is first developed to calculate the UA-to-UA collision risk given any two operational intent volumes. With this collision risk model, a test strategy is then proposed to assess if a strategic conflict detection service can reduce the collision risk and meet the target level of safety. The method also specifies operational data that are required to be collected to verify if requirements on conformance are being met. Additionally, two new requirements are identified and proposed by this method beyond the current standard for strategic conflict detection. In the sensitivity analysis, three main factors contributing to the collision risk are investigated. The analysis shows that buffers should be considered in a strategic conflict detection service when deconflicting operational intents. The results also reveal that the selection of test cases plays an important role in evaluating the strategic conflict detection service, and they should be representative and sufficiently complex in evaluation tests.

UTM↗
NASA NTRS2010

A Heat Transfer Investigation of Liquid and Two-Phase Methane

A heat transfer investigation was conducted for liquid and two-phase methane. The tests were conducted at the NASA Glenn Research Center Heated Tube Facility (HTF) using resistively heated tube sections to simulate conditions encountered in regeneratively cooled rocket engines. This testing is part of NASA s Propulsion and Cryogenics Advanced Development (PCAD) project. Nontoxic propellants, such as liquid oxygen/liquid methane (LO2/LCH4), offer potential benefits in both performance and safety over equivalently sized hypergolic propulsion systems in spacecraft applications. Regeneratively cooled thrust chambers are one solution for high performance, robust LO2/LCH4 engines, but cooling data on methane is limited. Several test runs were conducted using three different diameter Inconel 600 tubes, with nominal inner diameters of 0.0225-, 0.054-, and 0.075-in. The mass flow rate was varied from 0.005 to 0.07 lbm/sec. As the current focus of the PCAD project is on pressure fed engines for LO2/LCH4, the average test section outlet pressures were targeted to be 200 psia or 500 psia. The heat flux was incrementally increased for each test condition while the test section wall temperatures were monitored. A maximum average heat flux of 6.2 Btu/in.2 sec was achieved and, at times, the temperatures of the test sections reached in excess of 1800 R. The primary objective of the tests was to produce heat transfer correlations for methane in the liquid and two-phase regime. For two-phase flow testing, the critical heat flux values were determined where the fluid transitions from nucleate boiling to film boiling. A secondary goal of the testing was to measure system pressure drops in the two-phase regime.

VanNoord, Jonathan↗
NASA NTRS2013

HESTIA Commodities Exchange Pallet and Sounding Rocket Test Stand

During my Spring 2016 internship, my two major contributions were the design of the Commodities Exchange Pallet and the design of a test stand for a 100 pounds-thrust sounding rocket. The Commodities Exchange Pallet is a prototype developed for the Human Exploration Spacecraft Testbed for Integration and Advancement (HESTIA) program. Under the HESTIA initiative the Commodities Exchange Pallet was developed as a method for demonstrating multi-system integration thru the transportation of In-Situ Resource Utilization produced oxygen and water to a human habitat. Ultimately, this prototype's performance will allow for future evaluation of integration, which may lead to the development of a flight capable pallet for future deep-space exploration missions. For HESTIA, my main task was to design the Commodities Exchange Pallet system to be used for completing an integration demonstration. Under the guidance of my mentor, I designed, both, the structural frame and fluid delivery system for the commodities pallet. The fluid delivery system includes a liquid-oxygen to gaseous-oxygen system, a water delivery system, and a carbon-dioxide compressors system. The structural frame is designed to meet safety and transportation requirements, as well as the ability to interface with the ER division's Portable Utility Pallet. The commodities pallet structure also includes independent instrumentation oxygen/water panels for operation and system monitoring. My major accomplishments for the commodities exchange pallet were the completion of the fluid delivery systems and the structural frame designs. In addition, parts selection was completed in order to expedite construction of the prototype, scheduled to begin in May of 2016. Once the commodities pallet is assembled and tested it is expected to complete a fully integrated transfer demonstration with the ISRU unit and the Environmental Control and Life Support System test chamber in September of 2016. In addition to the development of the Commodities Exchange Pallet, I also assisted in preparation for testing the upper stage of a sounding rocket developed as a Center Innovation Fund project. The main objective of this project is to demonstrate the integration between a propulsion system and a solid oxide fuel cell (SOFC). The upper stage and SOFC are scheduled to complete an integrated test in August of 2016. As part of preparation for scheduled testing, I was responsible for designing the upper stage's test stand/support structure and main engine plume deflector to be used during hot-fire testing (fig. 3). The structural components of the test stand need to meet safety requirements for operation of the propulsion system, which consist of a 100 pounds-thrust main engine and two 15 pounds-thrust reaction control thrusters. My main accomplishment for this project was the completion of the design and the parts selection for construction of the structure, scheduled to begin late April of 2016.

Chaparro, Javier↗
NASA NTRS2022

Validation of the Mars 2020 Fault Protection Design: Navigating the Infinity of the Off-Nominal

On July 30th 2020, the Mars 2020 mission successfully launched out of Cape Canaveral, Florida, passed through the Earth’s shadow, and began its short cruise to Mars. Less than seven months later, the Perseverance rover touched down safely in Jezero Crater to begin its ambitious mission that includes looking for signs of ancient life and collecting samples for future return to Earth. Getting to the successful landing, or “Tango Delta Nominal,” could not have been achieved without also considering the off-nominal. One of the teams supporting this ambitious mission is the fault protection (FP) team. This team is tasked with assessing the various failures, or faults, that could prevent mission success and with ensuring that the autonomous behaviors built into the software and hardware can detect faults and recover the vehicle to a safe state. As part of its charter, the FP team designed a test campaign to provide confidence in the system’s robustness to off-nominal scenarios across all of Mars 2020’s mission phases. The greatest challenge associated with designing such a validation campaign was reducing the infinite number of anomalous scenarios into a finite test suite. In addition, the tests needed to be executed efficiently in order to utilize the team’s limited test venue access, but still needed to maintain a level of rigor that guaranteed confidence in the test outcomes. Given that each test scenario generated massive amounts of data, the team also developed methods for quickly ascertaining whether the autonomous fault protection behaviors maintained vehicle safety in the presence of an anomaly. This paper summarizes the processes that the Mars 2020 fault protection team employed to execute its off-nominal validation campaign. It captures both the methods of generating a suite of off-nominal tests, as well as reducing it to a subset that can be realistically executed within schedule and resource constraints. It also describes the various processes and philosophies that the team utilized to execute the tests efficiently, including creating a standardized procedure template, keeping the test cases modular so that they could be easily interchanged, and capturing common fault injections in a change-controlled database. Finally, it will describe the tools and processes for assessing the test data, focusing in particular on a tool that evaluated vehicle state using “secondary” sources of data to validate that the software had truly configured the spacecraft to the expected safe state.

Morantz, Chaz↗
NASA NTRS2020

Autonomous Assessment and Predictive Capabilities for Low-Altitude Urban Flight Operations

The integration of unmanned aerial vehicles in the national airspace will introduce new vehicle types, technologies, and operational paradigms for which safety must be maintained and hazards mitigated. One approach is to attempt to design for possible hazards and unsafe incidents that can occur at different phases of flight (pre-flight, in-flight, and post-flight) and during ground operations. Another is to mitigate safety incidents by implementing changes to policies, procedures, regulations, and design to cover personnel, equipment, and aircraft during operations. These and other techniques, not described herein, are typically conservative or adhoc in that they reduce the likelihood of risk after safety incidents have occurred. In this work, the goal is to develop a more predictive capability to monitor and mitigate risk and hazards to safety “in-time” enough for decisions to be made. In line with NASA’s Aeronautics Mission Directorate Strategic Thrust 5 [1] (In-Time System-Wide Safety Assurance), the System-Wide Safety (SWS) project under which this work falls, is developing and demonstrating innovative and safety-oriented solutions that enable modernization and aviation transformation. To that effect, this work will detail data-driven efforts on the SWS project to develop a number of safety-critical services for in-time monitoring and mitigation of hazards to low-altitude flight operations. First, hazards to these operations are identified based on previous work by NASA [2,3] and others in the aerospace industry. These hazards include (i) unsafe proximity to other vehicles, property, and people on the ground, (ii) critical system failures such as communication signal/GPS loss, unexpected propulsion system degradation, engine/power failure, and (iii) operational/environmental issues such as severe weather and gusty winds. For these hazards, safety metrics, which can be quantified and assessed are defined, models to monitor and predict them are developed, and flight test data is generated to develop, validate, and test these models, considering the complex interplay of the different hazards that define them [4-6]. In addition, the uncertainty in the non-deterministic effects that cannot be modeled nor predicted and unknown unknowns that arise after design/testing and during operations must be handled in rigorous manner. As a result, for each of the developed safety metrics, their dependencies on one another are characterized and a framework for handling the uncertainties inherent in the modeling, algorithms, and measurements required for prediction is also developed [7]. To that effect, this presentation will describe the safety metrics and services already developed and underway under the System-Wide Safety project that utilize data-driven techniques for the identification of anomalies, precursors, and trends (APTs) to monitor and mitigate hazards to safety, in-time, for urban flight operations in low-altitude airspace.

Okolo, Wendy A.↗
NASA NTRS2014

NASA's Space Launch System: Momentum Builds Towards First Launch

NASA's Space Launch System (SLS) is gaining momentum programmatically and technically toward the first launch of a new exploration-class heavy lift launch vehicle for international exploration and science initiatives. The SLS comprises an architecture that begins with a vehicle capable of launching 70 metric tons (t) into low Earth orbit. Its first mission will be the launch of the Orion Multi-Purpose Crew Vehicle (MPCV) on its first autonomous flight beyond the Moon and back. SLS will also launch the first Orion crewed flight in 2021. SLS can evolve to a 130-t lift capability and serve as a baseline for numerous robotic and human missions ranging from a Mars sample return to delivering the first astronauts to explore another planet. Managed by NASA's Marshall Space Flight Center, the SLS Program formally transitioned from the formulation phase to implementation with the successful completion of the rigorous Key Decision Point C review in 2014. At KDP-C, the Agency Planning Management Council determines the readiness of a program to go to the next life-cycle phase and makes technical, cost, and schedule commitments to its external stakeholders. As a result, the Agency authorized the Program to move forward to Critical Design Review, scheduled for 2015, and a launch readiness date of November 2018. Every SLS element is currently in testing or test preparations. The Program shipped its first flight hardware in 2014 in preparation for Orion's Exploration Flight Test-1 (EFT-1) launch on a Delta IV Heavy rocket in December, a significant first step toward human journeys into deep space. Accomplishments during 2014 included manufacture of Core Stage test articles and preparations for qualification testing the Solid Rocket Boosters and the RS-25 Core Stage engines. SLS was conceived with the goals of safety, affordability, and sustainability, while also providing unprecedented capability for human exploration and scientific discovery beyond Earth orbit. In an environment of economic challenges, the nationwide SLS team continues to meet ambitious budget and schedule targets through the studied use of hardware, infrastructure, and workforce investments the United States has already made in the last half century, while selectively using new technologies for design, manufacturing, and testing, as well as streamlined management approaches that have increased decision velocity and reduced associated costs. This paper will summarize recent SLS Program technical accomplishments, as well as the challenges and opportunities ahead for the most powerful and capable launch vehicle in history.

May, Todd↗
DOE OSTI1993

Nuclear Safety [Vol. 34, No. 1, January-March 1993]

Nuclear Safety is a review journal that covers significant developments in the field of nuclear safety. Its scope includes the analysis and control of hazards associated with nuclear energy, operations involving fissionable materials, and the products of nuclear fission and their effects on the environment. Primary emphasis is on safety in reactor design, construction, and operation; however, the safety aspects of the entire fuel cycle, including fuel fabrication, spent-fuel processing, nuclear waste disposal, handling of radioisotopes, and environmental effects of these operations, are also treated. Table of Contents for this issue follows. GENERAL SAFETY CONSIDERATIONS: 1 An Integrated Regional Approach To Risk Management of Industrial Systems, S. Chakraborty and R. Stratton; 9 Annual Technical Meeting of the NRC Cooperative Severe Accident Research Program, E. G. Silver; ACCIDENT ANALYSIS: 13 Deterministic Severe Accident Criteria as Severe Accident Design Criteria and Policy for the New Production Reactor-Heavy Water Reactor, P. T. Rhoads; 20 Proposed Deterministic Severe Accident Criteria for the Heavy Water Reactor-New Production Reactor Containment, K. D. Bergeron, S. E. Slezak, and C. E. Leach; 33 Quasi-Static Core Liquid Level Depression and Long-Term Core Uncovery During a PWR LOCA, Y. Kukita, R. R. Schultz, H. Nakamura, and J. Katayama; 49 LIRA: An Advanced Containment System to Minimize the Accidental Radioactivity Releases, A. Turricchia; 63 Errata to “A Review of Hydrogen Production During Melt/Water Interaction in LWRs,” Vol. 33, No. 4; CONTROL AND INSTRUMENTATION: 64 The Nuplex 80+™ Advanced Control Complex from ABB Combustion Engineering, F. Ridolfo, D. Harmon, and K. Scarola; DESIGN FEATURES: 76 A Scheme for Passive Isolation of the Containment of a Reactor, A. K. Ghosh, V. V. Raj, and K. Kakodkar; 84 Utility Requirements for Safety in the Passive Advanced Light-Water Reactor, T. U. Marston, W. H. Layman, and G. Bockhold, Jr.; WASTE AND SPENT FUEL MANAGEMENT: 91 Activities Related to Waste and Spent Fuel Management, Compiled by M. D. Muhlheim and E. G. Silver; OPERATING EXPERIENCES: 103 Testing Deficiencies in Auxiliary Systems Feedwater Systems, J. D. Kueck; 110 Reactor Shutdown Experience, Compiled by J. W. Cletcher; 113 Selected Safety-Related Events, Compiled by G. A. Murphy; 115 Operating U.S. Power Reactors, Compiled by M. D. Muhlheim and E. G. Silver; RECENT DEVELOPMENTS: 133 General Administrative Activities, Compiled by M. D. Muhlheim and E. G. Silver; 145 Reports, Standards, and Safety Guides, D. S. Queener; 150 Proposed Rule Changes as of Sept. 30, 1992; ANNOUNCEMENTS: 75 Harvard Short Course on Risk: Science, Assessment, and Management; 102 International Conference on Reactor Physics and Reactor Computations; 102 The Fourth International Conference on Nuclear Waste Reprocessing and Waste Management [RECOD ’94]; 132 International Symposium on the Radiological Exposure of the Population of the European Community from Radioactivity in the Mediterranean Sea [MARINA-MED]; 162 International High-Level Radioactive Waste Conference ‘Technology Integration—Above and Below”; 154 The Authors; 158 Indexes to Nuclear Safety, Volume 33.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗