Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “model testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91
All sourcesNASA NTRSDOE OSTI
NASA NTRS1918

An Investigation of the Elements which Contribute to Statical and Dynamical Stability, and of the Effects of Variation in Those Elements

Part 1 gives details of models tested and methods of testing of the Eiffel 36 wing alone and the JN2 aircraft. Characteristics and performance curves for standard JN are included. Part 2 presents a statistical analysis of the following: lift and drag contributed by body and chassis tested without wings; lift and drag contributed by tail, tested without wings; the effect on lift and drift of interference between the wings of a biplane combination; lift and drag contributed by the addition of body, chassis, and tail to a biplane combination; total parasite resistance; effect of varying size of tail, keeping angle of setting constant; effect of varying length of body and size of tail at the same time, keeping constant moment of tail surface about the center of gravity; forces on the tail and the effects of downwash; effect of size and setting of tail on statical longitudinal stability effects of length of body on stability; the effects of the various elements of an airplane on longitudinal stability and the placing of the force vectors. Part 3 presents the fundamental principals of dynamical stability; computations of resistance derivatives; solution of the stability equation; dynamical stability of the Curtiss JN2; tabulation of resistance derivatives; discussion of the resistance derivatives; formation and solution of stability equations; physical conceptions of the resistance derivatives; elements contributing to damping and an investigation of low speed conditions. Part 4 includes a summary of the results of the statistical investigation and a summary of the results for dynamic stability.

Klemin, Alexander↗
NASA NTRS1928

Characteristics of Five Propellers in Flight

This investigation was made for the purpose of determining the characteristics of five full-scale propellers in flight. The equipment consisted of five propellers in conjunction with a VE-7 airplane and a Wright E-2 engine. The propellers were of the same diameter and aspect ratio. Four of them differed uniformly in thickness and pitch and the fifth propeller was identical with one of the other four with exception of a change of the airfoil section. The propeller efficiencies measured in flight are found to be consistently lower than those obtained in model tests. It is probable that this is mainly a result of the higher tip speeds used in the full-scale tests. The results show also that because of differences in propeller deflections it is difficult to obtain accurate comparisons of propeller characteristics. From this it is concluded that for accurate comparisons it is necessary to know the propeller pitch angles under actual operating conditions. (author)

Crowley, J W , Jr↗
NASA NTRS1935

The Effect of Spray Strips on the Take-off Performance of a Model of a Flying-Boat Hull

The effect on the take-off performance of a model of the hull of a typical flying boat, Navy PH-1, of fitting spray strips of four different widths, each at three different angles, was determined by model tests in the NACA Tank. Spray strips of widths up to 3 percent of the beam improve the general performance at speeds near the hump and reduce the spray thrown. A downward angle of 30 degrees to 45 degrees in the neighborhood of the step seems most favorable for the reduction of the spray. The spray strips have a large effect in reducing the trimming moments at speeds near the hump speed, but have little effect on them at high speeds.

Truscott, Starr↗
NASA NTRS1952

Heat Transfer to Bodies in a High-speed Rarified-Gas Stream

Report presents the results of an investigation to determine the equilibrium temperature and heat-transfer coefficients for transverse cylinders in a high-speed stream of rarefied gas measured over a range of Knudsen numbers (ratio of molecular-mean-free path to cylinder diameter) from 0.025 to 11.8 and for Mach numbers from 2.0 to 3.3. The range of free-stream Reynolds numbers was from 0.28 to 203. The models tested were 0.0010-, 0.0050-, 0.030-, 0.051-, 0.080-, and 0.126-inch -diameter cylinders held normal to the stream.

Stalder, Jackson R↗
NASA NTRS1952

The Langley Annular Transonic Tunnel

Report describes the development of the Langley annular transonic tunnel, a facility in which test Mach numbers from 0.6 to slightly over 1.0 are achieved by rotating the test model in an annular passage between two concentric cylinders. Data obtained for two-dimensional airfoil models in the Langley annular transonic tunnel at subsonic and sonic speeds are shown to be in reasonable agreement with experimental data from other sources and with theory when comparisons are made for nonlifting conditions or for equal normal-force coefficients rather than for equal angles of attack. The trends of pressure distributions obtained from measurements in the Langley annular transonic tunnel are consistent with distributions calculated for Prandtl-Meyer flow.

Habel, Louis W↗
NASA NTRS1954

Studies of the Lateral-Directional Flying Qualities of a Tandem Helicopter in Forward Flight

An investigation of the lateral-directional flying qualities of a tandem-rotor helicopter in forward flight was undertaken to determine desirable goals for helicopter lateral-directional flying qualities and possible methods of achieving these goals in the tandem-rotor helicopter. Comparison between directional stability as measured in flight and rotor-off model tests in a wind tunnel shows qualitative agreement and, hence, indicates such wind-tunnel test, despite the absence of the rotors, to be one effective method of studying means of improving the directional stability of the tandem helicopter. Flight-test measurements of turns and oscillations, in conjunction with analytical studies, suggest possible practical methods of achieving the goals of satisfactory turn and oscillatory characteristics in the tandem helicopter.

Amer, Kenneth B↗
NASA NTRS1958

A method for simulating the atmospheric entry of long-range ballistic missiles

It is demonstrated with the aid of similitude arguments that a model launched from a hypervelocity gun upstream through a special supersonic nozzle should experience aerodynamic heating and resulting thermal stresses like those encountered by a long-range ballistic missile entering the earth's atmosphere. This demonstration hinges on the requirements that model and missile be geometrically similar and made of the same material, and that they have the same flight speed and Reynolds number (based on conditions just outside the boundary layer) at corresponding points in their trajectories. The hypervelocity gun provides the model with the required initial speed, while the nozzle scales the atmosphere, in terms of density variation, to provide the model with speeds and Reynolds numbers over its entire trajectory. Since both the motion and aerodynamic heating of a missile tend to be simulated in the model tests, this combination of hypervelocity gun and supersonic nozzle is termed an atmosphere entry simulator.

Eggers, A J , Jr↗
NASA NTRS1958

Effects of aerodynamic heating on X-15 temperatures

Paper describes examples which show how wind-tunnel model tests of the actual configuration of the aircraft aid in aerothermodynamic analyses and how these tests have made possible increased accuracy in structural temperature prediction. Also, from this and other research, development and design work on the X-15 has been done to accomplish a design consistent with the specified flight requirements. In this work, structural temperatures have been held within acceptable limits by providing sufficient heat sink material. Limited areas of the skin and leading edges are expected to attain temperatures greater than 1,200 degrees F. However, these areas have been carefully investigated for the effect of these higher temperatures on the structure and have been found to be satisfactory.

Kinsler, Martin R↗
NASA NTRS1955

Aerodynamic Loads on an External Store Adjacent to a 45 Degree Sweptback Wing at Mach Numbers from 0.70 to 1.96, Including an Evaluation of Techniques Used

Aerodynamic forces and moments have been obtained in the Langley 9- by 12-inch blowdown tunnel on an external store and on a 45 degree swept-back wing-body combination measured separately at Mach numbers from 0.70 to 1.96. The wing was cantilevered and had an aspect ratio of 4.0; the store was independently sting-mounted and had a Douglas Aircraft Co. (DAC) store shape. The angle of attack range was from -3 degrees to 12 degrees and the Reynolds number (based on wing mean aerodynamic chord) varied from 1.2 x10(6) to 1.7 x 10(6). Wing-body transonic forces and moments have been compared with data of a geometrically similar full-scale model tested in the Langley 16-foot and 8-foot transonic tunnels in order to aid in the evaluation of transonic-tunnel interference. The principal effect of the store, for the position tested, was that of delaying the wing-fuselage pitch-up tendency to higher angles of attack at Mach numbers from 0.70 to 0.90 in a manner similar to that of a wing chord extension. The most critical loading condition on the store was that due to side force, not only because the loads were of large magnitude but also because they were in the direction of least structural strength of the supporting pylon. These side loads were greatest at high angles of attack in the supersonic speed range. Removal of the supporting pylon (or increasing the gap between the store and wing) reduced the values of the variation of side-force coefficientwith angle of attack by about 50 percent at all test Mach numbers, indicating that important reductions in store side force may be realized by proper design or location of the necessary supporting pylon. A change of the store skew angle (nose inboard) was found to relieve the excessive store side loads throughout the Mach number range. It was also determined that the relative position of the fuselage nose to the store can appreciably affect the store side forces at supersonic speeds.

Guy, Lawrence D↗
NASA NTRS1951

State and development of flutter calculation

This report discusses the need for considering a wide variation in certain of the basic flutter parameters in conducting a flutter analysis. Conclusions are drawn stating that design charts or simple rules may be misleading. Due to inherent difficulties, dynamic model testing may also yield misleading results. The general flutter equations and various methods of solution are discussed. Of particular interest, curves are presented showing computational effort plotted against a number of degrees of freedom used in a flutter analysis.

VIBRATION AND FLUTTER - WINGS AND AILERONS↗
NASA NTRS1939

Experiments on a Slotted Wing

The results of pressure distribution measurements that were made on a model wing section of a Fieseler F 5 R type airplane are presented. Comparison of those model tests with the corresponding flight tests indicates the limitations and also the advantages of wind tunnel investigations, the advantages being particularly that through the variety of measuring methods employed the more complicated flow conditions may also be clarified. A fact brought out in these tests is that even in the case of "well rounded" slots it is possible for a vortex to be set up at the slot entrance and this vortex is responsible for certain irregularities in the pressure distribution and in the efficiency of the slot.

Ruden, P↗
NASA NTRS1935

The Aerodynamic Aspect of Wing-fuselage Fillets

Model tests prove the feasibility of enhancing the aerodynamic qualities of wing-fuselage fillets by appropriate design of fuselage and wing roots. Abrupt changes from maximum fuselage height to wing chord must be avoided and every longitudinal section of fuselage and wing roots must be so faired and arranged as to preserve the original lift distribution of the continuous wing. Adapting the fuselage to the curvilinear circulation of the wing affords further improvement. The polars of such arrangements are almost the same as those of the "wing alone," thus voiding the superiority of the high-wing type airplane known with conventional design.

Muttray, H↗
NASA NTRS1934

Stipa Monoplane with Venturi Fuselage

This report presents a detailed examination of the factors that went into the design of the Stipa monoplane. The model tested in the wind tunnel was made dissymmetrical externally, in order to produce a lift even at an angle of attack of 0 degrees with respect to the longitudinal axis of the tube.

Luigi Stipa↗
NASA NTRS1934

Supplemental data and calculations of the lateral stability of airplanes

In connection with the DVL Report 272 on the theory of the lateral stability of airplanes, the formal results are here amplified in some respects and their technical significance again briefly explained. Three numerical examples show how model tests for checking the lateral stability are to be evaluated and supplemented, if necessary, and how the stability limits depend on the design of the airplane and on the conditions of flight.

Mathias, Gotthold↗
NASA NTRS1934

Experiments with Planing Surfaces

A previous report discusses the experimental program of a systematic exploration of all questions connected with the planing problem as well as the first fundamental results of the investigation of a flat planing surface. The present report is limited to the conversion of the model test data to full scale.

Sottorf, W↗
NASA NTRS1931

The Take-Off of Seaplanes, Based on a New Hydrodynamic Reduction Theory

The interpretation of the take-off resistance of seaplane floats by model test involves a problem in mechanics, the solution of which forms the basis of this report. The comparison of three float forms is confined to an angle = 5 degree trim run in order to preserve the clearness of the arrangement. But for complete comparison the corresponding curves for several trim runs should be included.

Schroder, Paul↗
NASA NTRS1993

Numerical investigations in three-dimensional internal flows

In the present reporting period, the 3D version of the OVERFLOW code was used to solve the flow within the internal portion of the supersonic inlet. The internal portion of this inlet is bounded by an inflow plane containing the leading edge of the sidewalls, the sidewalls, the ramp and cowl surfaces and an outflow plane just downstream of the minimum geometric area of the inlet. Boundary layer bleed was used in the two-dimensional calculations discussed in the previous progress report and that same bleed was applied in the present study. For reference, this bleed corresponds to locations designated as R2 and R3 in the Mach 5 inlet model test. Using the GRIDGEN code, a three dimensional grid was generated that accounted for the viscous effects expected to occur on the sidewall, as well as those known to occur on the ramp and cowl surfaces. The internal flow grid size was 141 streamwise by 101 cross stream by 71 in the lateral direction between sidewalls. Since the flow entering the inlet was not symmetrical, the inlet was solved from sidewall to sidewall (without using a symmetry plane). In addition to the short sidewalls proposed in the Langley geometry database, a set of shorter sidewalls was also investigated in the present study and was shown to have beneficial effects with respect to the flow distortion exiting the supersonic inlet. In addition to these calculations, additional 3D solutions using the OVERFLOW code were obtained for the flow downstream of the throat of the supersonic inlet, including a terminal shock wave system produced by a backpressured subsonic diffuser.

Rose, William C.↗
NASA NTRS1993

Improved ceramic slip casting technique

A primary concern in modern fluid dynamics research is the experimental verification of computational aerothermodynamic codes. This research requires high precision and detail in the test model employed. Ceramic materials are used for these models because of their low heat conductivity and their survivability at high temperatures. To fabricate such models, slip casting techniques were developed to provide net-form, precision casting capability for high-purity ceramic materials in aqueous solutions. In previous slip casting techniques, block, or flask molds made of plaster-of-paris were used to draw liquid from the slip material. Upon setting, parts were removed from the flask mold and cured in a kiln at high temperatures. Casting detail was usually limited with this technique -- detailed parts were frequently damaged upon separation from the flask mold, as the molded parts are extremely delicate in the uncured state, and the flask mold is inflexible. Ceramic surfaces were also marred by 'parting lines' caused by mold separation. This adversely affected the aerodynamic surface quality of the model as well. (Parting lines are invariably necessary on or near the leading edges of wings, nosetips, and fins for mold separation. These areas are also critical for flow boundary layer control.) Parting agents used in the casting process also affected surface quality. These agents eventually soaked into the mold, the model, or flaked off when releasing the case model. Different materials were tried, such as oils, paraffin, and even an algae. The algae released best, but some of it remained on the model and imparted an uneven texture and discoloration on the model surface when cured. According to the present invention, a wax pattern for a shell mold is provided, and an aqueous mixture of a calcium sulfate-bonded investment material is applied as a coating to the wax pattern. The coated wax pattern is then dried, followed by curing to vaporize the wax pattern and leave a shell mold of the calcium sulfate-bonded investment material. The shell mold is cooled to room temperature, and a ceramic slip is poured therein. After a ceramic shell of desired thickness has set up in the shell mold, excess ceramic slip is poured out. While still wet, the shell mold is peeled from the ceramic shell to expose any delicate or detailed parts, after which the ceramic shell is cured to provide a complete, detailed, precision ceramic article without parting lines.

Buck, Gregory M.↗