Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “mixed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Modeling of surface-state induced inter-electrode isolation of n -on- p devices in mixed-field and γ -irradiation environments

Position sensitive n-on-p silicon sensors will be utilized in the tracker and in the High Granularity Calorimeter (HGCAL) of the Compact Muon Solenoid (CMS) experiment at High Luminosity Large Hadron Collider (HL-LHC). The detrimental effect of the radiation-induced accumulation of positive net oxide charge on position resolution in n-on-p sensors has typically been countered by the application of isolation implants like p-stop or p-spray between n + -electrodes. In addition to the positively charged layer inside the oxide and close to the Si/SiO 2 -interface, surface damage introduced by ionizing radiation in SiO 2 -passivated silicon particle detectors includes the accumulation of trapped-oxide-charge and interface traps. A previous study of either n/γ (mixed field)- or γ-irradiated Metal-Oxide-Semiconductor (MOS) capacitors showed evidence of substantially higher introduction rates of acceptor- and donor-type deep interface traps (N it,acc/don ) in mixed-field environment. Here, in this work, an inter-pad and -strip resistance (or resistivity (ρ int )) simulation study of n-on-p sensors with and without p-stop isolation implants was conducted for both irradiation types. Higher levels of ρint showed correlation to higher densities of deep N it,acc/don , with the inter-pad isolation performance of the mixed-field irradiated sensors becoming independent of the presence of p-stop implant between the n + - electrodes up to about 100 kGy. The low introduction rates of deep N it,acc/don in γ-irradiated sensors resulted in high sensitivity of ρ int to the presence and peak doping of p-stop above the lowest dose of about 7 kGy in the study. As a consequence of the advantageous influence of radiation-induced accumulation of deep N it on the inter-electrode isolation, position sensitive n-on-p sensors without isolation implants may be considered for future HEP-experiments where the radiation is largely due to hadrons.

Akchurin, N. [Texas Tech Univ., Lubbock, TX (Unite↗

Evidence for metal sources, fluid-mixing processes, and S isotope recycling within the feeder zone of an Irish type Zn-Pb deposit

The origin and evolution of fluids in Irish-type Zn-Pb deposits remains debated, particularly regarding the mobility of metals such as Cu and Ni, sources of sulphur, and the role of fluid mixing and replacement. The Lisheen Zn-Pb deposit, Ireland, offers a well-defined natural laboratory to investigate these questions. While most studies have focused on the Waulsortian Limestone Formation, the primary sulphide host, less is known about mineralisation in underlying units, such as the Lisduff Oolite Member (LOM). The LOM displays enrichment in Cu and Ni and displays intense replacement textures compared to other hosts at Lisheen, making it an ideal target for studying metal mobility and sulphur recycling in carbonate-hosted systems. Through characterising and studying LOM-hosted sulphides, valuable insights into mineralisation processes, especially related to Cu-Ni metals, can be defined. This study integrates petrography, EMPA, and in situ sulphur isotope (δ 34 S) analysis to investigate sulphide paragenesis, mineral chemistry, and fluid evolution across LOM ore zones. Results reveal a multistage mineralising system involving extensive replacement of early pyrite (Py0, δ 34 S = −28.4 to −21.9 ‰) by sphalerite and galena, with zoned pyrite (Py1) enriched in As-Cu-Ni-Tl. The δ 34 S values and trace element trends indicate mixing between hydrothermal and bacteriogenic sulphur-rich fluids, with evidence for sulphur recycling during replacement. Pyrite textures and compositions capture this evolving fluid regime, with trace element enrichment linked to paragenetic stage. The steel ore region, adjacent to major fault intersections, records intense hydrothermal fluid interaction, hosting Ni- and As-rich phases such as nickeline, gersdorffite, and arsenopyrite. These findings highlight the importance of structural controls and fluid mixing in metal transport and deposition, positioning the LOM as a key stratigraphic unit for understanding ore-forming processes in Irish-type systems. These results have implications for targeting similar carbonate-hosted systems globally, especially where deeper or structurally complex ore zones remain underexplored.

58 - GEOSCIENCES↗

On modeling Richtmyer–Meshkov turbulent mixing widths

In this paper, we present several observations concerning the Richtmyer- Meshkov mixing widths after a shock or reshock passes through the interface between two fluids. The mixing evolves with two oppositely-moving fronts: A bubble ( b ) side into the heavier fluid and a spike ( s ) side into the lighter fluid. Our first observation concerns the reference surface used to partition the total mix width, h b+s , into separate h b and h s widths. Next, we point out that if and when h b and h s obey power-laws t $\theta$ with separate $\theta$ b and $\theta$ s , then h b+s cannot be given, except as an approximation, by a single $\theta$ b+s . Finally, we describe a fully continuous model for h i (t) , i = b, s, or b + s , as the solution to the “drag equation” with a time-dependent $\theta$ i (t) .

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Extracting a mixing parameter from 2D radiographic imaging of variable-density turbulent flow

We extract a suitably averaged fluctuating density from the two-dimensional radiographic image of a flow. The X-ray attenuation is given by the Beer–Lambert law which exponentially damps the incident beam intensity by a factor proportional to the density, opacity and thickness of the target. By making reasonable assumptions for the mean density, opacity and effective thickness of the target flow, we estimate the density fluctuation contribution to the attenuation. The extracted density fluctuations averaged across the thickness of the flow in the direction of the beam may be used to form the density–specific-volume correlation $b$. In a statistical description of variable-density turbulence, $b$ quantifies the degree of mixedness. The ability to extract a measure of mixedness from experimental data would be a powerful tool that could be used in the validation of mix models. The scheme proposed is tested for DNS data computed for variable density buoyancy-driven mixing. We quantify the deficits in the extracted value of $b$ due to target thickness, Atwood number and modeled signal noise. This analysis justifies using the proposed scheme to infer the mix parameter from thin targets at moderate to low Atwood numbers. Furthermore, to illustrate how the scheme might be used in a practical problem, we demonstrate its application to a radiographic image of counter-shear flow obtained from experiments at the National Ignition Facility.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Advection versus diffusion in Richtmyer-Meshkov mixing

The Richtmyer-Meshkov (RM) instability is one of the most severe degradation mechanisms for inertial confinement fusion (ICF), and mitigating it has been a priority for the global ICF effort. In this Letter, the instability's ability to atomically mix is linked to its background decay of residual turbulent energy. Here, we show how recently derived inequalities from the mathematical theory of PDEs constrain the evolution. A model RM process at leading order may diffusively mix or retain imprints of its initial structures indefinitely, depending on initial conditions, and there exists a theoretical range of zero-mixing for certain values of parameters. The results may apply to other systems resembling scalar transport in decaying turbulence.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Evolution of the one-phonon 2{sup +}{sub 1,ms} mixed-symmetry state in N=80 isotones as a local measure for the proton-neutron interaction.

An inverse kinematics Coulomb excitation experiment was performed to obtain absolute E2 and M1 transition strengths in {sup 134}Xe. The measured transition strengths indicate that the 2{sub 3}{sup +} state of {sup 134}Xe is the dominant fragment of the one-phonon 2{sub 1,ms}{sup +} mixed-symmetry state. Comparing the energy of the 2{sub 1,ms}{sup +} mixed-symmetry state in {sup 134}Xe to that of the 2{sub 1,ms}{sup +} levels in the N=80 isotonic chain indicates that the separation in energy between the fully-symmetric {sub 1}{sup +} state and the {sub 1,ms}{sup +} level increases as a function of the number of proton pairs outside the Z=50 shell closure. This behavior can be understood as resulting from the mixing of the basic components of a two-fluid quantum system. A phenomenological fit based on this concept was performed. It provides the first experimental estimate of the strength of the proton-neutron quadrupole interaction derived from nuclear collective states with symmetric and antisymmetric nature.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Mixing and detonation structure in a rotating detonation engine with an axial air inlet

High-fidelity simulations of an experimental rotating detonation engine with an axial air inlet were conducted. The system operated with hydrogen as fuel at globally stoichiometric conditions. Instantaneous data showed that the detonation front is highly corrugated, and is considerably weaker than an ideal Chapman–Jouguet wave. Regions of deflagration are present ahead of the wave, caused by mixing with product gases from the previous cycle, as well as the injector recovery process. It is found that as the post-detonation high pressure flow expands, the injectors recover unsteadily, leading to a transient mixing process ahead of the next cycle. The resulting flow structure not only promotes mixing between product and reactant gases, but also increases likelihood of autoignition. These results show that the detonation process is very sensitive to injector design and the transient behavior during the detonation cycle. Phase-averaged statistics and conditionally averaged data are used to understand the overall reaction structure. As a result, comparisons with available experimental data on this configuration show remarkable good agreement of the predicted reacting flow structure.

42 ENGINEERING↗

Alloy selective optical sorting of mixed post-consumer aluminum scrap streams

Shredded post-consumer non-ferrous scrap stream, also known as Zorba, contains a mixture of cast and wrought aluminum pieces with very different compositions. Cast Al pieces, with their high Si, Cu and Fe content, are a major contaminant in wrought scrap fraction, which results in downcycling of the mixed cast + wrought scrap into non-structural cast Al alloys and parts. Here, in this paper, we introduce a chemical treatment method to color-code scrap aluminum pieces by alloy family and demonstrate low-cost optical sorting of cast from wrought pieces to upgrade the scrap stream. We utilized non-acidic chemical solutions that react with (i.e., etch) the scrap pieces to produce colors based on the Al alloy chemistry of a given piece. Cast pieces with high Si and Cu fractions turned black, whereas the much leaner wrought pieces remained unreacted. We showed > 95% sorting efficiency of mixed cast and wrought pieces using a repurposed low-cost optical sorter originally designed for food sorting. We also colored wrought Al pieces by alloy families, such as 5xxx and 6xxx, using a two-step chemical etching technique, which has the potential to create a circular supply chain in which wrought aluminum alloys are sorted from the mixed scrap stream and recycled back to high-value wrought products such as sheets, extrusions, and forgings with minimal contamination from cast scrap.

Aluminum↗

Optical and mass-spectral characterization of mixed-gas flowing atmospheric-pressure afterglow sources

Plasma-based ambient desorption/ionization (ADI) sources for mass spectrometry (MS) often use helium as the primary discharge gas due to the large reaction cross section of excited helium species with atmospheric gases, which ultimately leads to efficient reagent-ion formation. However, some studies have shown that mixed-gas plasmas provide unique advantages. For instance, our group showed that a helium-oxygen flowing atmospheric-pressure afterglow (He:O 2 -FAPA) source yielded enhanced ion signals for small polar analytes, but compounds with aromatic rings underwent chemical modification to produce pyrylium species. Here, it is shown that the addition of H 2 to the helium FAPA gas significantly decreased the reagent-ion signals, but analyte-ion signal was not affected to the same degree. In addition, mass spectra obtained with He:H 2 -FAPA were chemically cleaner with fewer ions stemming from analyte species and produced less oxidation of analytes. Addition of nitrogen increased the abundance of negative reagent ions (e.g., NO 2 - and NO 3 - ) which led to enhanced ion signal for RDX. To better understand these unique advantages of a mixed-gas FAPA, the impact of molecular-gas (O 2 , N 2 , or H 2 ) addition on the optical-emission spectra from the discharge was also measured. Spatially resolved emission was obtained from the anode- and negative-glow regions. In general, addition of small fractions (~0.1%) of molecular gases decreased helium and OH emission intensities. Atomic oxygen and hydrogen emission increased with the addition of O 2 and H 2 , respectively. Furthermore, emission characteristics of N 2 , N 2 + , and NO with respect to molecular gas composition on He-FAPA were measured. Finally, fundamental plasma parameters, such as OH rotational temperature (T rot ), were also calculated for these mixed-gas systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Pre-treating anaerobic mixed microflora with waste frying oil: A novel method to inhibit hydrogen consumption

Highlights: • Waste frying oil was successfully used as an inhibitor for H{sub 2} consumption during dark fermentation of mixed cultures. • Methane production in pre-treated cultures decreased significantly. • Duration of pre-treatment and concentration of waste frying oil affected H{sub 2} production. • Volatile fatty acids accumulation increased with waste frying oil concentration. - Abstract: An innovative method was introduced to inhibit methanogenic H{sub 2} consumption during dark fermentative hydrogen production by anaerobic mixed cultures. Waste frying oil was used as an inhibitor for hydrogenotrophic methanogens. Simultaneous effect of waste frying oil concentrations (0–20 g/L) and initial pH (5.5, 6.5 and 7.5) on inhibition of methanogenic H{sub 2} consumption and enhancement of H{sub 2} accumulation were investigated using glucose as substrate. Enhanced hydrogen yields with decreased methane productions were observed with increasing the waste frying oil concentrations. On average, CH{sub 4} productions from glucose in the cultures received 10 g/L WFO were reduced by 88%. Increased WFO concentration up to 20 g/L led to negligible CH{sub 4} productions and in turn enhanced H{sub 2} yields. Hydrogen yields of 209.26, 195.35 and 185.60 mL/g glucose{sub added} were obtained for the cultures pre-treated with 20 g/L waste frying oil with initial pH of 5.5, 6.5 and 7.5 respectively. H{sub 2} production by pre-treated cultures was also studied using a synthetic food waste. Anaerobic mixed cultures were pre-treated with 10 g/L WFO and varying durations (0, 24 and 48 h). A H{sub 2} yield of 71.46 mL/g VS was obtained for cultures pre-treated with 10 g/L WFO for 48 h that was 475% higher than untreated control. This study suggests a novel and inexpensive approach for suppressing hydrogenotrophic methanogens during dark fermentative H{sub 2} production.

08 HYDROGEN↗

Stream lamination and rapid mixing in a microfluidic jet for X-ray spectroscopy studies

Microfluidic mixers offer new possibilities for the study of fast reaction kinetics down to the microsecond time scale, and methods such as soft X-ray absorption spectroscopy are powerful analysis techniques. These systems impose challenging constraints on mixing time scales, sample volume, detection region size and component materials. The current work presents a novel micromixer and jet device which aims to address these limitations. The system uses a so-called ‘theta’ mixer consisting of two sintered and fused glass capillaries. Sample and carrier fluids are injected separately into the inlets of the adjacent capillaries. At the downstream end, the two streams exit two micron-scale adjoining nozzles and form a single free-standing jet. The flow-rate difference between the two streams results in the rapid acceleration and lamination of the sample stream. This creates a small transverse dimension and induces diffusive mixing of the sample and carrier stream solutions within a time scale of 0.9 microseconds. The reaction occurs at or very near a free surface so that reactants and products are more directly accessible to interrogation using soft X-ray. We use a simple diffusion model and quantitative measurements of fluorescence quenching (of fluorescein with potassium iodide) to characterize the mixing dynamics across flow-rate ratios.

Huyke, Diego A. (ORCID:0000000283356613)↗

The effect of initial conditions on mixing transition of the Richtmyer–Meshkov instability

We investigate the late-time Richtmyer–Meshkov instability (RMI) growth of sinuous perturbations on an air/sulphur hexafluoride interface (Atwood number, A ~ 0.67 ) subjected to a Mach 1.2 planar shock wave at Los Alamos National Laboratory's vertical shock tube facility. Interface perturbations are established using a novel membraneless technique where cross-flowing air and SF 6 separated by an oscillating splitter plate create a perturbed density interface. The interface formed has multi-modal features and residual small perturbations, however, a dominant mode is still noticeable. The late-time perturbation growths scale with $ka_0$ initial conditions (where $k$ is the wavenumber and $a_0$ is the initial amplitude of the dominant mode) as measured at the pre-shock interface. Past nonlinear models based on potential-flow theory, heuristic/interpolation approaches, Padé approximants and numerical simulations are evaluated against present experimental results. Accounting for an explicit $ka_0$ dependence in Sadot et al.'s model, we propose an empirical rational function that captures the asymptotic behaviour of perturbation growth for a broad range of initial conditions ( 0.30 $≤ ka_0 ≤$ 0.86 ). The onset of mixing transition and its initial condition dependence are investigated with respect to the minimum state criterion ($Re =$ 1.6 $\times$ 10 5 ) for unsteady flows by Zhou. Earlier mixing transitions for higher ka0 initial conditions are noted from local and global Reynolds number estimates which are corroborated by the existence of an inertial sub-range and formation of mixing regions indicating the physical significance of the minimum state criterion in RMI flows. The transition is accompanied by the increasing teapot-like appearance of joint probability density functions of $p–q$ (invariants of the reduced velocity gradient tensor), establishing the technique as a useful tool for turbulence detection in two-dimensional diagnostics.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Oceanic mixing and waves in the presence of a suspended canopy

Large-eddy simulations are analysed to determine the influence of suspended canopies, such as those formed in macroalgal farms, on ocean mixed layer (OML) deepening and internal wave generation. In the absence of a canopy, we show that Langmuir turbulence, when compared with wind-driven shear turbulence, results in a deeper OML and more pronounced internal waves beneath the OML. Subsequently, we examine simulations with suspended canopies of varying densities located in the OML, in the presence of a background geostrophic current. Intensified turbulence occurs in the shear layer at the canopy’s bottom edge, arising from the interaction between the geostrophic current and canopy drag. Structures resembling Kelvin–Helmholtz (KH) instability emerge as the canopy shear layer interacts with the underlying stratification, radiating internal waves beneath the OML. Both intensified turbulence and lower-frequency motions associated with KH-type structures are critical factors in enhancing mixing. Consequently, the OML depth increases by up to a factor of two compared with cases without a canopy. Denser canopies and stronger geostrophic currents lead to more pronounced KH-type structures and internal waves, stronger turbulence and greater OML deepening. Additionally, vertical nutrient transport is enhanced as the OML deepens due to the presence of the canopy. Considering that the canopy density investigated in this study closely represents offshore macroalgal farms, these findings suggest a mechanism for passive nutrient entrainment conducive to sustainable farming. Overall, this study reveals the intricate interactions between the suspended canopy, turbulent mixing and stratification, underscoring their importance in reshaping OML characteristics.

Bo, Tong (ORCID:0000000260300561)↗

Exploring the Influence of Linker Substitution and Ratios on Cooperative Framework Flexibility through the Mixed-Linker Approach

Cooperatively flexible metal–organic frameworks that exhibit step-shaped, or Type V-like, adsorption–desorption profiles can lower requisite pressure–temperature swings and thus energy input, necessary for an array of gas storage, delivery, and separations applications. However, such benefits are lost if the pressure threshold of the adsorption and desorption steps at a given temperature does not match the conditions dictated by the application, such as H 2 storage and delivery or olefin–paraffin separations. Unfortunately, the discovery of cooperatively flexible frameworks remains wholly serendipitous and de novo design remains impossible. Accordingly, there is a great need to further our understanding of flexibility such that we can intuitively derivatize known frameworks and, ultimately, design entirely new ones to meet the requisite conditions of energy-consumptive processes. In this work, we demonstrate that the mixed-linker, or multivariate, approach is a powerful tool for the derivation of a known flexible framework, with variances in linker substitution and ratio giving rise to a family wherein significant changes to the step-shaped adsorption–desorption profiles for multiple adsorbates are observed. Specifically, we report 12 isostructural mixed-linker derivatives of CdIF-13 (sod–Cd(benzimidazolate) 2 ) with six point-modified benzimidazole linkers spontaneously synthesized through prototypical solvothermal conditions. Furthermore, each is shown by PXRD to exhibit similar reversible flexibility to CdIF-13 and by TGA and DSC to be similarly thermally stable. Isothermal gas adsorption measurements with N 2 at 77 K, CO 2 at 195 K, and propane at 298 K demonstrate the wide-ranging, adsorbate-dependent effects of linker substitution and ratio, including dramatic reductions in the adsorption threshold pressure, evolution of multiple steps, and complete absence of observable adsorption. Aided by prior crystallographic characterization of CdIF-13, the observed trends were analyzed in an attempt to resolve the influence of linker substitution and ratios on structural behavior. In total, this work illustrates how the mixed-linker approach enables the synthesis and study of a large catalog of functionally modified frameworks, which can help identify the variables that influence flexibility and sorption behavior.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Atomic-Resolution Visualization of Distinctive Chemical Mixing Behavior of Ni, Co and Mn with Li in Layered Lithium Transition-Metal Oxide Cathode Materials

Capacity and voltage fading of layer structured cathode based on lithium transition metal oxide is closely related to the lattice position and migration behavior of the transition metal ions. However, it is scarcely clear about the behavior of each of these transition metal ions. We report direct atomic resolution visualization of interatomic layer mixing of transition metal (Ni, Co, Mn) and lithium ions in layer structured oxide cathodes for lithium ion batteries. Using chemical imaging with aberration corrected scanning transmission electron microscope (STEM) and DFT calculations, we discovered that in the layered cathodes, Mn and Co tend to reside almost exclusively at the lattice site of transition metal (TM) layer in the structure or little interlayer mixing with Li. In contrast, Ni shows high degree of interlayer mixing with Li. The fraction of Ni ions reside in the Li layer followed a near linear dependence on total Ni concentration before reaching saturation. The observed distinctively different behavior of Ni with respect to Co and Mn provides new insights on both capacity and voltage fade in this class of cathode materials based on lithium and TM oxides, therefore providing scientific basis for selective tailoring of oxide cathode materials for enhanced performance.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Persistent dopants and phase segregation in organolead mixed-halide perovskites

Organolead mixed-halide perovskites such as CH 3 NH 3 PbX 3–a X' a (X, X' = I, Br, Cl) are interesting semiconductors because of their low cost, high photovoltaic power conversion efficiencies, enhanced moisture stability, and band gap tunability. Using a combination of optical absorption spectroscopy, powder X-ray diffraction (XRD), and, for the first time, 207 Pb solid state nuclear magnetic resonance (ssNMR), we probe the extent of alloying and phase segregation in these materials. Because 207 Pb ssNMR chemical shifts are highly sensitive to local coordination and electronic structure, and vary linearly with halogen electronegativity and band gap, this technique can provide the true chemical speciation and composition of organolead mixed-halide perovskites. We specifically investigate samples made by three different preparative methods: solution phase synthesis, thermal annealing, and solid phase synthesis. 207 Pb ssNMR reveals that nonstoichiometric dopants and semicrystalline phases are prevalent in samples made by solution phase synthesis. We show that these nanodomains are persistent after thermal annealing up to 200 °C. Further, a novel solid phase synthesis that starts from the parent, single-halide perovskites can suppress phase segregation but not the formation of dopants. Our observations are consistent with the presence of miscibility gaps and spontaneous spinodal decomposition of the mixed-halide perovskites at room temperature. This underscores how strongly different synthetic procedures impact the nanostructuring and composition of organolead halide perovskites. In conclusion, better optoelectronic properties and improved device stability and performance may be achieved through careful manipulation of the different phases and nanodomains present in these materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Instability and efficiency of mixed halide perovskites CH 3 NH 3 AI 3- x Cl x (A = Pb and Sn): A first-principles, computational study

Here, we carried out calculations based on density functional theory to investigate the electronic, vibrational, and dielectric properties of mixed halide perovskites CH 3 NH 3 AI 3– x Cl x with A = Pb and Sn. Computed free energies indicated that Cl mixed systems may be formed only for Cl concentrations not exceeding 10 19 cm –3 , and phonon calculations showed that the disorder induced in the host lattice by the presence of a smaller halogen is responsible for mechanical instabilities. However, we found that the presence of chloride may be beneficial to the electronic properties of the perovskites. Chloride anions cause the organic cations to be displaced from the center of the cage; such a displacement induces preferential orientations of the cation dipole, which in turn are responsible for notable changes in the dielectric properties of the material and possibly for the formation of local ferroelectric domains. The latter are instrumental in separating electron hole pairs and hence in contributing to long charge-carrier diffusion lengths, in spite of polarons being more likely formed in mixed perovksites than in CH 3 NH 3 AI 3 .

36 MATERIALS SCIENCE↗

Kinetics of Direct Olefin Synthesis from Syngas over Mixed Beds of Zn–Zr Oxides and SAPO-34

A packed bed containing a physical mixture of both Zn–Zr mixed oxide catalyst and SAPO-34 converts syngas directly into a mixture of C 2 –C 5 olefins and paraffins. Specifically, the mixed oxide catalyst is responsible for intermediate oxygenate synthesis from syngas while the molecular sieve catalyzes olefin synthesis from the oxygenate intermediates. Kinetic measurements with cofed propylene over each catalyst independently confirm olefin hydrogenation activity over both components of the composite bed. The addition of either water or CO to the feed drops the activity of propylene hydrogenation over the Zn–Zr oxide. In sum, under reaction conditions of syngas feed and produced water, olefin hydrogenation predominantly occurs over the SAPO-34 catalyst, rather than over the catalyst responsible for hydrogenating CO into oxygenate intermediates. Here, a developed kinetic model consistent with this conclusion describes measurements at differing feed compositions, temperatures, space velocities, and bed catalyst mixing ratios. Technoeconomic analysis of the process indicates that the olefin-to-paraffin ratio is a key performance metric for commercial scale syngas conversion and highlights the importance of considering olefin hydrogenation rates over the molecular sieve component.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗