Development of optimum fabrication techniques for brazed tantalum/Type 316 stainless steel tubular transition joints Final report
Development of optimum fabrication techniques for brazed stainless steel transition joints
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Development of optimum fabrication techniques for brazed stainless steel transition joints
Design and development of module joint clamping device for application to solar array construction
Thermal shock testing of coextruded and brazed tubular joints of stainless steel and tantalum for SNAP-8 application
Universal joints for connecting two displaced shafts or members
Prediction of bolted joint heat transfer in spacecraft applications
Joint assessment and management evaluation system
Bimetallic refractory metal joints electron beam welding and aging for applications to in-pile thermionic converters
Fracture mechanics and time dependent strength of elastic or viscoelastic solids adhesively jointed by soft polymeric bonding layer
Stress distribution in plates and tubes bonded by stepped joints, assuming generalized plane stress
The contact of two rough, wavy surfaces; the contact of two rough but nominally flat plates pressed together over a concentrated area; and the contact of two rough but nominally flat plates bolted together are considered. In each case the pressure distribution is calculated as a function of the surface properties. In the case of wavy surfaces it is found that all necessary information for any combination of parameters can be reduced to one master graph. In the other two cases one such graph is needed for each geometry used. The resulting pressure distributions are used in a specific heat transfer example and the total joint resistance versus roughness is presented. A method for decreasing the resistance by increasing the roughness is shown.
This metallurgical program was specifically conducted for the establishment of material properties required for the design of the LF460 fan. The LF460 lift fan is an advanced 18:1 high thrust to weight single stage design. It has a turbine attached to the outer flowpath of the fan blade tip which minimizes the axial depth of the fan. Advanced lightweight attachment designs are employed in this concept to achieve minimum mass polar moments of inertia which are required for good aircraft flight response control. The design features which are unique to this advanced LF460 lift fan are the 0.010 inch thin Udimet 700 alloy integral tip turbine design, minimum weight braze attachment of the turbine to the fan blade, and the high strength and elevated temperature capability of the Rene'95 alloy for the fan blade. The data presented in this report show that the LF460 fan rotor design is feasible and that the design stresses and margins of safety were more than adequate. Prior to any production application, however, additional stress rupture/shear lap joints should be run in order to establish a firm 1200 F stress rupture curve for the CM50 braze metal.
When an amplitude-stabilized He-Ne laser beam is scattered by a rotating ground glass with small surface inhomogeneities, the probability density of the instantaneous scattered-wave amplitude is Gaussian. In this paper, we suggest the use of the joint photon-count probability distribution to measure the absolute value of the electric-field amplitude-correlation function for random Gaussian light fields, and report the results of an experiment in which the Gaussian field is produced by scattering a light beam through a rotating ground glass. This procedure offers an alternative to other conventional methods, such as self-beating spectroscopy and irradiance-correlation techniques. The correlation time of the scattered-field amplitude in the present experiment has been measured with an accuracy of approximately 0.8%.
Study examines effects of boron filament diameter on bonds and joints in boron-aluminum composite. Data include static strength, fatigue, and dynamic moduli of elasticity. Manson-Coffin analyses and metallurgical and fracture surface evaluation were also performed.
Axial tension and compression are transmitted between end fittings and fiberglass tube without depending on glass-to-metal bonding, conventional fasteners or combination of these things. Joint design significantly reduces both structural weight of strut and its cross-sectional area.
Static and fatigue loading tests of bonded lap joints were conducted. The specimens were designed to fail in the bondline and all fatigue tests included monitoring the crack growth to failure. Detailed crack length readings for 106 fatigue specimens are provided.
The engineering, design, and fabrication status of the expansion joint unit (EJU) to be employed in the NaK primary coolant piping loop of the 5-kwe Reactor thermoelectric system are described. Four EJU's are needed in the NaK primary coolant piping loop. The four EJU's which will be identical, utilize bellows as the flexing member, are hermetically sealed, and provide double containment. The bellows are of a nested-formed design, and are to be constructed of 1-ply thickness of 0.010-in. Inconel 718. The EJU's provide a minimum piping load margin of safety of +0.22.
Bonded lap joints were manufactured and tested under static and fatigue loading. Specimens were designed to fail in the bondline, and all fatigue tests included monitoring the crack growth to failure. Test specimens included aluminum details joined by two different adhesives. Specimens also included titanium and boron-epoxy details joined by an epoxy laminating resin. Additonal program variables included bondline thickness, adherend and spice plate thickness, specimen width, and specimen fabrication procedure. Adhesive aging was found to be generally detrimental to the lives of most of the specimens bonded with one adhesive system. Adhesive material was found to have a major influence on debond rate. Co-cured titanium/boron-epoxy specimens were found to resist debonding better than specimens fabricated with a sequential cure. Splice plate thickness and test section width were found to have little effect on debond rate. The data also suggested the existence of an optimum bondline thickness.