Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dynamic loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Seismic analysis of the large 70-meter antenna, part 1: Earthquake response spectra versus full transient analysis

As a check on structure safety aspects, two approaches in seismic analysis for the large 70-m antennas are presented. The first approach, commonly used by civil engineers, utilizes known recommended design response spectra. The second approach, which is the full transient analysis, is versatile and applicable not only to earthquake loading but also to other dynamic forcing functions. The results obtained at the fundamental structural frequency show that the two approaches are in good agreement with each other and both approaches show a safe design. The results also confirm past 64-m antenna seismic studies done by the Caltech Seismology Staff.

Kiedron, K.↗
NASA NTRS1985

Dynamic modeling and adaptive control for space stations

Of all large space structural systems, space stations present a unique challenge and requirement to advanced control technology. Their operations require control system stability over an extremely broad range of parameter changes and high level of disturbances. During shuttle docking the system mass may suddenly increase by more than 100% and during station assembly the mass may vary even more drastically. These coupled with the inherent dynamic model uncertainties associated with large space structural systems require highly sophisticated control systems that can grow as the stations evolve and cope with the uncertainties and time-varying elements to maintain the stability and pointing of the space stations. The aspects of space station operational properties are first examined, including configurations, dynamic models, shuttle docking contact dynamics, solar panel interaction, and load reduction to yield a set of system models and conditions. A model reference adaptive control algorithm along with the inner-loop plant augmentation design for controlling the space stations under severe operational conditions of shuttle docking, excessive model parameter errors, and model truncation are then investigated. The instability problem caused by the zero-frequency rigid body modes and a proposed solution using plant augmentation are addressed. Two sets of sufficient conditions which guarantee the globablly asymptotic stability for the space station systems are obtained.

Ih, C. H. C.↗
NASA NTRS1987

Monogroove cold plate

The coolant fluid evaporated in a compact heat absorbing panel utilizing monogroove heat pipes in a pumped two-phase system is replenished through a liquid inlet control valve under the control of an ultrasonic liquid presence detector which is connected to the panel. The detector maintains the desired liquid quantity in the panel's liquid coolant channels, thereby dynamically responding to varying heat loads.

Edelstein, Fred↗
NASA NTRS1988

Comprehensive analysis of helicopters with bearingless rotors

A modified Galerkin method is developed to analyze the dynamic problems of multiple-load-path bearingless rotor blades. The development and selection of functions are quite parallel to CAMRAD procedures, greatly facilitating the implementation of the method into the CAMRAD program. A software is developed implementing the modified Galerkin method to determine free vibration characteristics of multiple-load-path rotor blades undergoing coupled flapwise bending, chordwise bending, twisting, and extensional motions. Results are in the process of being obtained by debugging the software.

Murthy, V. R.↗
NASA NTRS1987

The Phase II ROTONET system

The improvements introduced in Phase II of ROTONET, a comprehensive computer program developed at NASA Langley for predicting helicopter noise, are reviewed and demonstrated. The ROTONET functional modules for lifting-rotor performance, lifting-rotor noise, rotor loads, rotor inflow, rotor rigid dynamics, rotor wake geometry, rotor tone noise, and rotor broadband noise are briefly characterized; the construction of an acoustics data base from measurements taken in flight tests of a NASA/MDHC 500E helicopter is described; and the validation tests are summarized. Good agreement between flight-test data and ROTONET predictions is obtained.

Golub, Robert A.↗
NASA NTRS1989

The effect of an unsteady three-dimensional wake on elastic blade-flapping eigenvalues in hover

This paper describes the formulation of a finite-state inflow model based on an acceleration potential and a helical wake geometry. The states of the model are coefficients of an inflow expansion in terms of a Fourier series (azimuthally) and of special polynomials (radially). The integrals over the wake are done in closed-form to obtain a set of ordinary differential equations for the inflow coefficients. The forcing functions for these equations are generalized forces which are integrals of the blade loading exactly as in structural dynamics. This model implicitly includes (for the hover case) Prandtl-Goldstein tip losses, dynamic inflow, and Theodorsen/Loewy lift deficiency. Thus, it is a fully three-dimensional unsteady wake model. Here, this model is coupled with elastic-blade equations in hover and eigenvalues are found. The results show that the three-dimensional wake has a large effect on the flap damping of all modes.

Peters, David A.↗
NASA NTRS1993

Unsteady evaporation and combustion of a drop cluster inside a vortex

A model has been developed which describes the evaporation, ignition and combustion of a drop cluster embedded in a large vortex. The purpose of this model is to simulate the behavior of drops in large coherent vortices produced in the shear layer of a jet. The model treats the dynamic interactions between the drops and the vortex, and also takes into account the drop proximity to calculate the heat and mass transfers between drops and ambient gas. The gas phase outside the cluster is treated as an unsteady, reacting phase, whereas quasi-steadiness is assumed between the drops and surrounding gas inside the cluster. The results show a very complex interaction between the dynamics of the drop-loaded vortex, the flame, and the evaporation process.

Fichot, F.↗
NASA NTRS1994

Atomic oxygen durability evaluation of the flexible batten for the photovoltaic array mast on Space Station

A test program was conducted at the National Aeronautics and Space Administration's Lewis Research Center (LeRC) to evaluate the long term low Earth orbital (LEO) atomic oxygen (AO) durability of a flexible (fiberglass-epoxy composite) batten. The flexible batten is a component used to provide structural rigidity in the photovoltaic array mast on Space Station. The mast is used to support and articulate the photovoltaic array, therefore, the flexible batten must be preloaded for the 15 year lifetime of an array blanket. Development hardware and composite materials were evaluated in ground testing facilities for AO durability and dynamic retraction-deployment cyclic loading representative of expected full life in-space application. The CV1144 silicone (AO protective) coating was determined to provide adequate protection against AO degradation of the composite material and provided fiber containment, thus the structural integrity of the flexible batten was maintained. Both silicone coated and uncoated flexible battens maintained load carrying capabilities. Results of the testing did indicate that the CV1144 silicone protective coating was oxidized by AO reactions to form a brittle glassy (SiO2) skin that formed cracking patterns on all sides of the coated samples. The cracking was observed in samples that were mechanically stressed as well as samples in non-stressed conditions. The oxidized silicon was observed to randomly spall in small localized areas, on the flexible battens that underwent retraction-deployment cycling. Some darkening of the silicon, attributed to vacuum ultraviolet (VUV) radiation, was observed.

Stidham, Curtis R.↗
NASA NTRS1997

Robot Position Sensor Fault Tolerance

Robot systems in critical applications, such as those in space and nuclear environments, must be able to operate during component failure to complete important tasks. One failure mode that has received little attention is the failure of joint position sensors. Current fault tolerant designs require the addition of directly redundant position sensors which can affect joint design. A new method is proposed that utilizes analytical redundancy to allow for continued operation during joint position sensor failure. Joint torque sensors are used with a virtual passive torque controller to make the robot joint stable without position feedback and improve position tracking performance in the presence of unknown link dynamics and end-effector loading. Two Cartesian accelerometer based methods are proposed to determine the position of the joint. The joint specific position determination method utilizes two triaxial accelerometers attached to the link driven by the joint with the failed position sensor. The joint specific method is not computationally complex and the position error is bounded. The system wide position determination method utilizes accelerometers distributed on different robot links and the end-effector to determine the position of sets of multiple joints. The system wide method requires fewer accelerometers than the joint specific method to make all joint position sensors fault tolerant but is more computationally complex and has lower convergence properties. Experiments were conducted on a laboratory manipulator. Both position determination methods were shown to track the actual position satisfactorily. A controller using the position determination methods and the virtual passive torque controller was able to servo the joints to a desired position during position sensor failure.

Aldridge, Hal A.↗
NASA NTRS2001

Thermal Fatigue and Fracture Behavior of Ceramic Thermal Barrier Coatings

Thermal fatigue and fracture behavior of plasma-sprayed ceramic thermal barrier coatings has been investigated under high heat flux and thermal cyclic conditions. The coating crack propagation is studied under laser heat flux cyclic thermal loading, and is correlated with dynamic fatigue and strength test results. The coating stress response and inelasticity, fatigue and creep interactions, and interface damage mechanisms during dynamic thermal fatigue processes are emphasized.

Zhu, Dong-Ming↗
NASA NTRS1994

Parallel DSMC Solution of Three-Dimensional Flow Over a Finite Flat Plate

This paper describes a parallel implementation of the direct simulation Monte Carlo (DSMC) method. Runtime library support is used for scheduling and execution of communication between nodes, and domain decomposition is performed dynamically to maintain a good load balance. Performance tests are conducted using the code to evaluate various remapping and remapping-interval policies, and it is shown that a one-dimensional chain-partitioning method works best for the problems considered. The parallel code is then used to simulate the Mach 20 nitrogen flow over a finite-thickness flat plate. It is shown that the parallel algorithm produces results which compare well with experimental data. Moreover, it yields significantly faster execution times than the scalar code, as well as very good load-balance characteristics.

Nance, Robert P.↗
NASA NTRS1995

Affect of Brush Seals on Wave Rotor Performance Assessed

The NASA Lewis Research Center's experimental and theoretical research shows that wave rotor topping can significantly enhance gas turbine engine performance levels. Engine-specific fuel consumption and specific power are potentially enhanced by 15 and 20 percent, respectively, in small (e.g., 400 to 700 hp) and intermediate (e.g., 3000 to 5000 hp) turboshaft engines. Furthermore, there is potential for a 3- to 6-percent specific fuel consumption enhancement in large (e.g., 80,000 to 100,000 lbf) turbofan engines. This wave-rotor-enhanced engine performance is accomplished within current material-limited temperature constraints. The completed first phase of experimental testing involved a three-port wave rotor cycle in which medium total pressure inlet air was divided into two outlet streams, one of higher total pressure and one of lower total pressure. The experiment successfully provided the data needed to characterize viscous, partial admission, and leakage loss mechanisms. Statistical analysis indicated that wave rotor product efficiency decreases linearly with the rotor to end-wall gap, the square of the friction factor, and the square of the passage of nondimensional opening time. Brush seals were installed to further minimize rotor passage-to-cavity leakage. The graph shows the effect of brush seals on wave rotor product efficiency. For the second-phase experiment, which involves a four-port wave rotor cycle in which heat is added to the Brayton cycle in an external burner, a one-dimensional design/analysis code is used in conjunction with a wave rotor performance optimization scheme and a two-dimensional Navier-Stokes code. The purpose of the four-port experiment is to demonstrate and validate the numerically predicted four-port pressure ratio versus temperature ratio at pressures and temperatures lower than those that would be encountered in a future wave rotor/demonstrator engine test. Lewis and the Allison Engine Company are collaborating to investigate wave rotor integration in an existing turboshaft engine. Recent theoretical efforts include simulating wave rotor dynamics (e.g., startup and load-change transient analysis), modifying the one-dimensional wave rotor code to simulate combustion internal to the wave rotor, and developing an analytical wave rotor design/analysis tool based on macroscopic balances for parametric wave rotor/engine analysis.

Source record↗
NASA NTRS2007

Crew Exploration Vehicle (CEV) Water Landing Simulation

Crew Exploration Vehicle (CEV) water splashdowns were simulated in order to find maximum acceleration loads on the astronauts and spacecraft under various landing conditions. The acceleration loads were used in a Dynamic Risk Index (DRI) program to find the potential risk for injury posed on the astronauts for a range of landing conditions. The DRI results showed that greater risks for injury occurred for two landing conditions; when the vertical velocity was large and the contact angle between the spacecraft and the water impact surface was zero, and when the spacecraft was in a toe down configuration and both the vertical and horizontal landing velocities were large. Rollover was also predicted to occur for cases where there is high horizontal velocity and low contact angles in a toe up configuration, and cases where there was a high horizontal velocity with high contact angles in a toe down configuration.

Littell, Justin D.↗
NASA NTRS1961

Effect of Load-Alleviating Structure on the Landing Behavior of a Reentry-Capsule Model

Model tests have been made to determine the landing-impact characteristics of a parachute-supported reentry capsule that had a compliable metal structure as a load-alleviating device. A 1/6-scale dynamic model having compliable aluminum-alloy legs designed to give a low onset rate of acceleration on impact was tested at flight-path angles of 90 degrees (vertical) and 35 degrees, at a vertical velocity of 30 ft/sec (full scale), and at contact attitudes of 0 degrees and +/-30 degrees. Landings were made on concrete, sand, and water.

[Division] Structures↗
NASA NTRS1963

Investigation of the Landing Characteristics of a Re-entry Vehicle Having a Canted Multiple Air Bag Load Alleviation System

An investigation was made to determine the landing-impact characteristics of a reentry vehicle having a multiple-air-bag load-alleviation system. A 1/16-scale dynamic model having four canted air bags was tested at flight-path angles of 90 degrees (vertical), 45 degrees, and 27 degrees for a parachute or paraglider vertical letdown velocity of 30 feet per second (full scale). Landings were made on concrete at attitudes ranging from -l5 degrees to 20 degrees. The friction coefficient between the model heat shield and the concrete was approximately 0.4. An aluminum diaphragm, designed to rupture at 10.8 pounds per square inch gage, was used to maintain initial pressure in the air bags for a short time period.

TESTS↗
DOE OSTI2020

Managing time-substitutable electricity usage using dynamic controls

A predictive-control approach allows an electricity provider to monitor and proactively manage peak and off-peak residential intra-day electricity usage in an emerging smart energy grid using time-dependent dynamic pricing incentives. The daily load is modeled as time-shifted, but cost-differentiated and substitutable, copies of the continuously-consumed electricity resource, and a consumer-choice prediction model is constructed to forecast the corresponding intra-day shares of total daily load according to this model. This is embedded within an optimization framework for managing the daily electricity usage. A series of transformations are employed, including the reformulation-linearization technique (RLT) to obtain a Mixed-Integer Programming (MIP) model representation of the resulting nonlinear optimization problem. In addition, various regulatory and pricing constraints are incorporated in conjunction with the specified profit and capacity utilization objectives.

Ghosh, Soumyadip↗
DOE OSTI2023

Expandable systems for space

Systems for insulating a space vehicle or space borne container from an external environment as well as cryogens from heat sources. Such systems also protect the vehicle from the high dynamic pressures, the high heat loads encountered in atmospheric flight, and provide storage capability that strongly limits, or effectively eliminates, cryogenic boil-off losses once in space. Such systems include an expandable structure having a plurality of contiguously adjacent expandable layers. The layers are connected by a plurality of tension connectors between successive layers. For launch and flight the layers can be restrained in a collapsed position. Whereupon exiting a free stream environment, the layers are expanded where they can lock into place or otherwise remain in an expanded state. The expansion creates separation between the layers with minimal conduction paths providing near theoretically perfect multi-layer insulation and extremely effective debris protection.

de Jong, Maxim↗
NASA NTRS1975

Dynamic analysis and test results of the Viking Orbiter

The Viking Orbiter (VO) was launched in August 1975 on a new Titan/Centaur launch vehicle. Weight limitations of the VO and the use of a new launch vehicle made it necessary to conduct a load analysis which was verified by a test. The load analysis required a good mathematical dynamic model. Attention is given to aspects of mathematical formulation, subsystem characteristics, the body displacement functions, the propulsion subsystem, details regarding the dynamic model, the static test, and the sine vibration test.

Wada, B. K.↗