SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Flywheel safety and containment design technology are discussed. The effects of axial loading resulting from composite rotor burst tests are considered. Analysis of the radial burst problem is also included.
Among the various candidate materials tested, stainless steel shows the best potential for applications as heat exchanger components in solar ponds. Even stainless steel may lead to pitting type of corrosion. Weight loss measurements are probably unsatisfactory for corrosion evaluation in solar pond situations. Also included are the results from the potentiodynamic anodic polarization analysis, corrosion rate calculation via corrosion behavior diagrams, and immersion weight loss measurements.
The effect of weightlessness on the human operator's performance in force reflecting position control of remote manipulators was investigated. A gravity compensation system was developed to simulate the effect of weightlessness on the operator's arm. A universal force reflecting hand controller (FRHC) and task simulation software were employed. Two experiments were performed because of anticipated disturbances in neuromotor control specification on the human operator in an orbital control environment to investigate: (1) the effect of controller stiffness on the attainment of a learned terminal position in the three dimensional controller space, and (2) the effect of controller stiffness and damping on force tracking of the contour of a simulated three dimensional cube using the part simulation of weightless conditions. The results support the extension of neuromotor control models, which postulate a stiffness balance encoding of terminal position, to three dimensional motion of a multilink system, confirm the existence of a disturbance in human manual control performance under gravity compensated conditions, and suggest techniques for compensation of weightlessness induced performance decrement through appropriate specification of hand controller response characteristics. These techniques are based on the human control model.
Although a specific configuration has not been selected for the Space Station, a gravity gradient stabilized station as a basis upon which to compare various structural and construction concepts is considered. The Space Station primary truss support structure is described in detail. Three approaches (see sketch A) which are believed to be representative of the major techniques for constructing large structures in space are also described in detail so that salient differences can be highlighted.
Reasons for the development of artificial gravity environments on spacecraft are outlined. The physiological effects of weightlessness on the human cardiovascular skeletal, and vestibular systems are enumerated. Design options for creating artificial gravity environments are shown.
Weightlessness produces significant physiological changes. Whether these changes will stabilize or achieve medical significance is not clear. Artificial gravity is the physiological countermeasure, and the tether system represents an attractive approach to artificial gravity. The need for artificial gravity is examined.
The effect of the meteoroid/space debris environment on the design and evolution of spacecraft waste heat rejection radiator systems is discussed. Active radiator systems; i.e., systems in which waste heat is collected from the various heat sources within a spacecraft and delivered to the radiator system by a heat transport loop are emphasized. The heat is distributed over the radiator area and thus rejected to space. Present and future systems are discussed.
The present rates of man-made, space object propagation are such that there is a real probability of self propagation which, if uncontrolled can lead to a serious limitation to future uses of spacecraft for beneficial purposes. Effective control over the debris issue requires adoption and adherence to policy at a world wide level (any one nation's unknowing, selfish or deliberately adverse action can conceivably jeopardize other useful applications of space satellites for years into the future). The near-term environment may not seriously jeopardize the near-term missions. However, absence of control and/or nonadherence to a control policy in the near-term can result in a debris environment that can severely limit long - term mission opportunities. The data upon which these observations are based continues to be investigated. These investigations tend to validate the preceding observations and emphasize the need for near-term action to establish responsible control policy and implementation actions.
The Marshall Space Flight Center's X-ray Calibration Facility was constructed for preflight calibration of the HEAO-B X-ray Telescope (1978-1981). Calibration requirements for a newly proposed X-ray telescope, AXAF (scheduled for flight early 1990's), go beyond the capabilities of the facility at present. Several of these new requirements are discussed, among them: (1) the production of a pure unpolarized X-ray beam, (2) minimizing the target/tube change over time, and (3) how to configure the X-ray source chamber to effectively accommodate both polarized and unpolarized X-ray sources.
Feedback shift registers are efficient periodic binary sequence generators. Polynomials of degree r over a Galois field characteristic 2(GF(2)) characterize the behavior of shift registers with linear logic feedback. The algorithmic determination of the trinomial of lowest degree, when it exists, that contains a given irreducible polynomial over GF(2) as a factor is presented. This corresponds to embedding the behavior of an r-stage shift register with linear logic feedback into that of an n-stage shift register with a single two-input modulo 2 summer (i.e., Exclusive-OR gate) in its feedback. This leads to Very Large Scale Integrated (VLSI) circuit architecture of maximal regularity (i.e., identical cells) with intercell communications serialized to a maximal degree.
The sizing and performance analyses have been conducted in the design of long-endurance, high-altitude airplanes. These airplanes receive power either continuously beamed from a phased array transmitter or intermittently beamed from a dish transmitter. Results are presented for the cases of flight in zero wind speed and nonzero wind speed. Sensitivity studies indicate that the vehicle size is relatively insensitive to changes in the transmitter size. Cost estimates were made using models that excluded the airplane cost. Using a reference payload, results obtained from array and dish configurations were compared. Comparisons showed savings in cost as well as smaller vehicle sizes when an array transmitter was used.
A feed system design for large space antenna systems was considered. A multiple aperture system with nonoverlapping feeds is examined. Circular and quadrant aperture reflector radiation patterns are compared and the effect of adjacent aperture on radiation patterns of multiple aperture reflector antennas is illustrated. The following systems are examined: (1) feed design optimization for a multiple aperture reflector antenna; (2) radiation pattern for two quadrant reflector with optimized feed design; (3) multiple beam concept utliizing apertures and nonoverlapping feeds; (4) beam contours for two quadrant of multiple beam multiple aperture concept; (5) superposition of beams from two quadrants of multiple beam multiple aperture concent; (6)compensation for mislalignment of interleaved beams from two quadrants; and (7) beam quality improvement due to reorienting feed for offset reflector.
Contiguous multiple beams are used to make use of the set of frequency bands at different beams at different geographical locations and achieve the most efficient use of precious frequency allocation. This is feasible only if the interference among cochannel beams is below some acceptable level, by carrier/interference (C/I) ratio. Individual beam patterns of very low sidelobes, which in turn necessitates narrow feed are required. A physically realizable solution to this problem entails either more than one reflector, more complicated optics, or breaking of each feed into a cluster of smaller elements, some of which would then be shared by adjacent beams. The latter, however, requires a complicated beamforming network (BFN) for the proper feeding of the elements. The feedpacking problem is not unique to reflector antennas and exists in lens type antennas as well. The BFN and associated problems are present in the phased array antennas and on a much larger scale. Poor scan capabilities are associated with reflector systems. The scan properties of offset fed reflector systems can be improved by choosing a very large focal length to parent reflector diameter ((F/Dp) ratio, which requires a longer boom to support the feed. In the case of reflectors with cluster feed arrangements, the scan capability for smaller F/Dp ratios is improved by proper adjustment of cluster element excitations. Such a system seems to be appropriate for up to 10 beamwidths scan. For a larger number of beams, systems with wider scan capabilities, such as phased arrays or phased array/reflector combinations, become more appealing.
It appears likely that the Land Mobile Satellite Services (LMSS) will be authorized by the FCC for operation in the 800 to 900 MHz (UHF) and possibly near 1500 MHz (L-band). Propagation problems are clearly an important factor in the effectiveness of this service, but useful measurements are few, and produced contradictory interpretations. A first order overview of existing measurements is presented with particular attention to the first two NASA balloon to mobile vehicle propagation experiments. Some physical insight into the interpretation of propagation effects in LMSS transmissions is provided.
In considering damage tolerant design concepts for gas turbine hot section components, several challenging concerns arise: Complex multiaxial loading situations are encountered; Thermomechanical fatigue loading involving very wide temperature ranges is imposed on components; Some hot section materials are extremely anisotropic; and coatings and environmental interactions play an important role in crack propagation. The effects of multiaxiality and thermomechanical fatigue are considered from the standpoint of their impact on damage tolerant design concepts. Recently obtained research results as well as results from the open literature are examined and their implications for damage tolerant design are discussed. Three important needs required to advance analytical capabilities in support of damage tolerant design become readily apparent: (1) a theoretical basis to account for the effect of nonproportional loading (mechanical and mechanical/thermal); (2) the development of practical crack growth parameters that are applicable to thermomechanical fatigue situations; and (3) the development of crack growth models that address multiple crack failures.
The design criteria for a compact magnetograph that can monitor solar magnetic fields from a free-flying satellite for 5 to 10 years are reviewed. The signal-to-noise ratio that can be obtained with a 10-cm f/10 refractor operated with a Fabry-Perot filter and a solid-state detector array is derived. The telescope measures the longitudinal component of the magnetic field for the entire solar disk in a few minutes at a 20-G threshold and at 3-arcsec resolution. The Fabry-Perot filter has a lithium niobate etalon, which can be tuned electrically and operated at a fixed tilt angle in such a manner that it cancels the solar rotational Doppler shifts in the transmitted spectrum. Principles of operation of various types of polarization modulators are presented, and it is concluded that photoelastic modulators and liquid-crystal devices hold the most promise for use in a satellite-borne magnetograph,
Several unified constitutive models were tested in uniaxial form by specifying input strain histories and comparing output stress histories. The purpose of the tests was to evaluate several time integration methods with regard to accuracy, stability, and computational economy. The sensitivity of the models to slight changes in input constants was also investigated. Results are presented for In100 at 1350 F and Hastelloy-X at 1800 F.
The back contact can detract from solar cell performance in a number of ways: high recombination, barrier, photovoltaic, minority carrier collection, resistance. These effects may act in a nonuniform fashion over the cell area, and complicate the analysis of photovoltaic performance aimed at a better understanding of the effects of device geometry and material and/or processing parameters. The back contact is tested by reproducing it on both sides of a substrate. The objective is to find a back contact which performs well as a back contact, can be applied cheaply to large area solar cells, fits well into a practical process sequence, does not introduce structural damage or undesirable impurities into the silicon substrate, is compatible with an effective front contact technology, permits low temperature solder contacting, adheres well to silicon, and is reliable.