Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “configurable”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Advanced turboprop aircraft flyover noise annoyance - Comparison of different propeller configurations

A laboratory experiment was conducted to compare the annoyance of flyover noise from advanced turboprop aircraft having different propeller configurations with the annoyance of conventional turboprop and jet aircraft flyover noise. It was found that advanced turboprops with single-rotating propellers were, on average, slightly less annoying than the other aircraft. Fundamental frequency and tone-to-broadband noise ratio affected annoyance response to advanced turboprops but the effects varied with propeller configuration and noise metric. The addition of duration corrections and corrections for tones above 500 Hz to the noise measurement procedures improved prediction ability.

Mccurdy, David A.↗

Integration of scramjets with waverider configurations

This paper presents a parametric study of a scramjet propulsion system integrated into a waverider lifting-body configuration. The analysis explores the effect of inlet geometry, internal cross-section-area distribution of the combustor section, the distribution of the heat release of the reacting mixture, the heat transfer, and the friction on the performance of the propulsion system. The Mach number, temperature, and pressure distributions within the scramjet model are studied parametrically, and the effects on the thrust are obtained. The results provide insight on the design concepts and problems that might arise for a given internal-flow configuration.

Rasmussen, M. L.↗

Measured and predicted aerodynamic heating on a cylinder in wake of AFE configuration at incidence

Thin-film resistance gages were used to measure cylinder surface heat-transfer rates in the near wake of the Aeroassist Flight Experiment vehicle configuration, while surface-streamline directions were ascertained by the oil-flow techniques under the same configuration and test conditions. Both heat transfer distributions and flow over the entire cylinder surface were influenced by impingement of that portion of the free shear layer originating at the forebody shoulder in the upper symmetry plane. Heating rate distributions predicted with a Navier-Stokes solver computer code were in general agreement with measurements.

Wells, William L.↗

A comparison of the ground effects measured with and without rate-of-descent modeling on the F-15 S/MTD configuration

The effect of descent rate (DR) on the approach aerodynamics of the F-15 S/MTD aircraft is investigated experimentally using a moving model in the NASA Langley Vortex Research Facility. A 0.083-scale low-speed rotary-balance model equipped with a thrust-reverser simulator and with grit strips to assure turbulent flow was tested in an approach configuration at forward speed 60 ft/sec, corresponding to DR = 4.19 ft/sec. The results are presented in extensive graphs and compared with wind-tunnel data on the same configuration at DR = 0. Significant differences are attributed to the DR in the present experiments and the presence of a ground boundary layer in the wind-tunnel tests. It is predicted that safe approaches could be made with the lower thrust reverser vectored up to 80 deg, or even 110 deg if the DR were not arrested near the ground.

Kemmerly, Guy T.↗

Feasibility study of vortex interaction control on a chine forebody/delta wing configuration at high angles of attack

The feasibility of controlling vortex interactions or merger on a blended chine forebody and delta wing configuration was experimentally investigated. Low-speed wind tunnel diagnostics using smoke visualizations and wing upper-surface pressure measurements were performed on a generic 60 deg delta and chine forebody model, to assess chine modifications and leading edge flaps. Both techniques were shown to promote uncoupled vortex flows at high angles of attack and sideslip, with significant influence on the wing flow field, indicating potential for alleviating adverse high-alpha characteristics of blended chine swept wing configurations.

Rao, Dhanvada M.↗

Wind-tunnel investigation of the low-speed aerodynamics of slender accelerator-type configurations

The NASA-Langley 14x22-ft subsonic wind tunnel has been used to ascertain the low speed aerodynamics of a conical-forebody/annular conformal propulsion system/truncated conical afterbody hypersonic-accelerator configuration with delta-planform wing. Six-component force-and-moment data were obtained over the -4 to +30 deg alpha range and + or - 20 deg sideslip. Flow visualization diagnostics were used to characterize configuration aerodynamics. Vortex flows from the conical forebody created large values of local inflow angles at the engine inlet locations on the lee side of the model, at the moderate-alpha values associated with takeoff and landing.

Gatlin, Gregory M.↗

High-alpha flight dynamics research on the X-29 configuration using dynamic model test techniques

High-angle-of-attack flight dynamics of the X-29 configuration were studied using dynamic model test techniques. These tests identified phenomena including wing rock, spins, and tumbling which dominate the high-alpha behavior of the configuration and define its usable flight envelope. Results of these tests have been used to design flight control concepts to minimize adverse behavior. Planned high-angle-of-attack flight tests of the X-29 airplane will provide an opportunity to validate the model predictions.

Croom, Mark A.↗

Computational design of low aspect ratio wing-winglet configurations for transonic wind-tunnel tests

Computational designs were performed for three different low aspect ratio wing planforms fitted with nonplanar winglets; one of the three configurations was selected to be constructed as a wind tunnel model for testing in the NASA LaRC 8-foot transonic pressure tunnel. A design point of M = 0.8, C(sub L) is approximate or = to 0.3 was selected, for wings of aspect ratio equal to 2.2, and leading edge sweep angles of 45 deg and 50 deg. Winglet length is 15 percent of the wing semispan, with a cant angle of 15 deg, and a leading edge sweep of 50 deg. Winglet total area equals 2.25 percent of the wing reference area. The design process and the predicted transonic performance are summarized for each configuration. In addition, a companion low-speed design study was conducted, using one of the transonic design wing-winglet planforms but with different camber and thickness distributions. A low-speed wind tunnel model was constructed to match this low-speed design geometry, and force coefficient data were obtained for the model at speeds of 100 to 150 ft/sec. Measured drag coefficient reductions were of the same order of magnitude as those predicted by numerical subsonic performance predictions.

Kuhlman, John M.↗

Supersonic aerodynamic characteristics of a proposed Assured Crew Return Capability (ACRC) lifting-body configuration

An investigation was conducted in the Langley Unitary Plan Wind Tunnel at Mach numbers from 1.6 to 4.5. The model had a low-aspect-ratio body with a flat undersurface. A center fin and two outboard fins were mounted on the aft portion of the upper body. The outboard fins were rolled outboard 40 deg from the vertical. Elevon surfaces made up the trailing edges of the outboard fins, and body flaps were located on the upper and lower aft fuselage. The center fin pivoted about its midchord for yaw control. The model was longitudinally stable about the design center-of-gravity position at 54 percent of the body length. The configuration with undeflected longitudinal controls trimmed near 0 deg angle of attack at Mach numbers from 1.6 to 3.0 where lift and lift-drag ratio were negative. Longitudinal trim was near the maximum lift-drag ratio (1.4) at Mach 4.5. The model was directionally stable over Mach number range except at angles of attack around 4 deg at M = 2.5. Pitch control deflection of more than -10 deg with either elevons or body flaps is needed to trim the model to angles of attack at which lift becomes positive. With increased control deflection, the lifting-body configuration should perform the assured crew return mission through the supersonic speed range.

Ware, George M.↗

Preliminary evaluation of space station transmission line in a ring configuration

The results of a preliminary evaluation of a space station type transmission line and commercial transmission lines in a ring configuration, are reported. In a ring configuration, each node has two paths for the return current of each wire. The additional path can create an unbalanced condition, where the magnetic fields created by the forward and return currents do not cancel. This evaluation was to quantify the effects of the unbalanced case upon the external fields. The transmission lines evaluated were standard commercial coaxial cables, RG59 and RG213, and a space station designed flat Litz transmission line. Each was evaluated in a balanced and unbalanced mode of operation. Currents and their harmonic content were recorded and compared. As expected, the harmonic content of the different current (I delta) was substantial for the unbalanced case as compared to the balanced case. For the balanced case, very little difference was noted among the various transmission lines evaluated. The evaluation is discussed, and the test circuit, the measurements, and the resulting data are described.

Roth, Mary Ellen↗

An aerodynamic tradeoff study of the scissor wing configuration

A scissor wing configuration, consisting of two independently sweeping wings was numerically studied. This configuration was also compared with an equivalent fixed wing baseline. Aerodynamic and stability and control characteristics of these geometries were investigated over a wide range of flight Mach numbers. It is demonstrated that in the purely subsonic flight regime, the scissor wing can achieve higher aerodynamic efficiency as the result of slightly higher aspect ratio. In the transonic regime, the lift to drag ratio of the scissor wing is shown to be higher than that of the baseline, for higer values of the lift coefficient. This tends to make the scissor wing more efficient during transonic cruise at high altitudes as well as during air combat at all altitudes. In supersonic flight, where the wings are maintained at maximum sweep angle, the scissor wing is shown to have a decided advantage in terms of reduced wave drag. From the view point of stability and control, the scissor wing is shown to have distinct advantages. It is shown that this geometry can maintain a constant static margin in supersonic as well as subsonic flight, by proper sweep scheduling. Furthermore, it is demonstrated that addition of wing mounted elevons can greatly enhance control authority in pitch and roll.

Selberg, Bruce P.↗

The effects of magnetic nozzle configurations on plasma thrusters

Plasma thrusters have been operated at power levels from 10 kw to 0.1 MW. When these devices have had magnetic fields applied to them which form a nozzle configuration for the expanding plasma, they have shown marked increases in exhaust velocity which is in direct proportion to the magnitude of the applied field. Further, recent results have shown that electrode erosion may be influenced by applied magnetic fields. This research effort is directed to the experimental and computational study of the effects of applied magnetic field nozzles in the acceleration of plasma flows. Plasma source devices which eliminate the plasma interaction in normal thrusters are studied as most basic. Normal thruster configurations were studied without applied fields and with applied magnetic nozzle fields. Unique computational studies utilize existing codes which accurately include transport processes. Unique diagnostic studies supported the experimental studies to generate new data. Both computation and diagnostics were combined to indicate the physical mechanisms and transport properties that are operative in order to allow scaling and accurate prediction of thruster performance.

York, Thomas M.↗

Application of the TRANAIR rectangular grid approach to the aerodynamic analysis of complex configurations

A numerical method is described which uses a rectangular grid to solve the nonlinear full potential equation about complex configurations. The grid is locally refined to resolve high velocity gradients arising from leading edge expansions or shock waves. The grid penetrates the boundary (described by networks of quadrilateral panels) and is generated automatically. Discrete operators are constructed using the finite element method. The system of nonlinear discrete equations is solved iteratively using a Krylov subspace method preconditioned by an exterior Poisson solver and a direct sparse solver. The primary emphasis is to provide design engineers with an aerodynamic analysis tool (the TRANAIR code) which is accurate, reliable, economical, and flexible to use. Computational results for many interesting configurations are presented.

Johnson, Forrester T.↗

Dynamic ground-effect measurements on the F-15 STOL and Maneuver Technology Demonstrator (S/MTD) configuration

A moving-model ground-effect testing method was used to study the influence of rate-of-descent on the aerodynamic characteristics for the F-15 STOL and Maneuver Technology Demonstrator (S/MTD) configuration for both the approach and roll-out phases of landing. The approach phase was modeled for three rates of descent, and the results were compared to the predictions from the F-15 S/MTD simulation data base (prediction based on data obtained in a wind tunnel with zero rate of descent). This comparison showed significant differences due both to the rate of descent in the moving-model test and to the presence of the ground boundary layer in the wind tunnel test. Relative to the simulation data base predictions, the moving-model test showed substantially less lift increase in ground effect, less nose-down pitching moment, and less increase in drag. These differences became more prominent at the larger thrust vector angles. Over the small range of rates of descent tested using the moving-model technique, the effect of rate of descent on longitudinal aerodynamics was relatively constant. The results of this investigation indicate no safety-of-flight problems with the lower jets vectored up to 80 deg on approach. The results also indicate that this configuration could employ a nozzle concept using lower reverser vector angles up to 110 deg on approach if a no-flare approach procedure were adopted and if inlet reingestion does not pose a problem.

Kemmerly, Guy T.↗

Supersonic flow computations for an ASTOVL aircraft configuration, phase 2, part 2

A unified space/time marching method was used to solve the Euler and Reynolds-averaged Navier-Stokes equations for supersonic flow past an Advanced Short Take-off and Vertical Landing (ASTOVL) aircraft configuration. Lift and drag values obtained from the computations compare well with wind tunnel measurements. The entire calculation procedure is described starting from the geometry to final postprocessing for lift and drag. The intermediate steps include conversion from IGES to the patch specification needed for the CFD code, grid generation, and solution procedure. The calculations demonstrate the capability of the method used to accurately predict design parameters such as lift and drag for very complex aircraft configurations.

Ramakrishnan, Sekaripuram V.↗

Transformational part-count in layered octahedral-tetrahedral truss configurations

The number of component part (nodes, struts and panels) termed part count, is an important factor in the design, manufacture, and assembly of modular space structures. Part count expressions are presented for a variety of profiles derived from the layered octahedral-tetrahedral truss configuration. Referred to as the tetrahedral truss in the NASA projects, this specific geometry has been used in several missions. The general expressions presented here transforms to others as one profile changes to another. Such transformational part count relations provide a measure of flexibility and generality, and may be useful when dealing with a wider range of geometric configurations.

Lalvani, Haresh↗

A neural network for controlling the configuration of frame structure with elastic members

A neural network for controlling the configuration of frame structure with elastic members is proposed. In the present network, the structure is modeled not by using the relative angles of the members but by using the distances between the joint locations alone. The relationship between the environment and the joints is also defined by their mutual distances. The analog neural network attains the reaching motion of the manipulator as a minimization problem of the energy constructed by the distances between the joints, the target, and the obstacles. The network can generate not only the final but also the transient configurations and the trajectory. This framework with flexibility and parallelism is very suitable for controlling the Space Telerobotic systems with many degrees of freedom.

Tsutsumi, Kazuyoshi↗

Annoyance caused by advanced turboprop aircraft flyover noise: Counter-rotating-propeller configuration

Two experiments were conducted to quantify the annoyance of people to flyover noise of advanced turboprop aircraft with counter rotating propellers. The first experiment examined configurations having an equal number of blades on each rotor and the second experiment examined configurations having an unequal number of blades on each rotor. The objectives were to determine the effects on annoyance of various tonal characteristics, and to compare annoyance to advanced turboprops with annoyance to conventional turboprops and turbofans. A computer was used to synthesize realistic, time-varying simulations of advanced turboprop aircraft takeoff noise. The simulations represented different combinations fundamental frequency and tone-to-broadband noise ratio. Also included in each experiment were recordings of 10 conventional turboprop and turbofan takeoffs. Each noise was presented at three sound pressure levels in an anechoic chamber. In each experiment, 64 subjects judged the annoyance of each noise stimulus. Analyses indicated that annoyance was significantly affected by the interaction of fundamental frequency with tone-to-broadband noise ratio. No significant differences in annoyance between the advanced turboprop aircraft and the conventional turbofans were found. The use of a duration correction and a modified tone correction improved the annoyance prediction for the stimuli.

Mccurdy, David A.↗