Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “boundary layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Pseudo-direct solution to the boundary-layer equations for separated flow

This paper describes a procedure for the automatic iteration of an inverse boundary-layer technique to a prescribed pressure distribution in a separated flow. The technique is demonstrated by computation of two transonic airfoil flows and two externally generated shock boundary-layer interaction flows. These results are compared to experimental data and to solutions of the full Navier-Stokes equations. These comparisons indicate that substantial economies can be obtained by applying methods like the present, in lieu of full Navier-Stokes methods, in zonal calculation schemes for design purposes. The optimization technique leading to convergence is described in detail and a table of typical computation time is presented.

Arieli, R.↗
NASA NTRS1991

Experimental study of boundary layer transition on a heated flat plate

A detailed investigation to the document momentum and thermal development of boundary layers undergoing natural transition on a heated flat plate was performed. Experimental results of both overall and conditionally sampled characteristics of laminar, transitional, and low Reynolds number turbulent boundary layers are presented. Measurements were done in a low-speed, closed-loop wind tunnel with a freestream velocity of 100 ft/s and zero pressure gradient over a range of freestream turbulence intensities from 0.4 to 6 percent. The distributions of skin friction, heat transfer rate, and Reynolds shear stress were all consistent with previously published data. Reynolds analogy factors for momentum thickness Reynolds number, Re(sub theta) less than 2300 were found to be well predicted by laminar and turbulent correlations which accounted for an unheated starting length and uniform heat flux. A small dependence of turbulence results on the freestream turbulence intensity was observed.

Sohn, K. H.↗
NASA NTRS1991

Experimental study of boundary layer transition on a heated flat plate

A detailed investigation to the document momentum and thermal development of boundary layers undergoing natural transition on a heated flat plate was performed. Experimental results of both overall and conditionally sampled characteristics of laminar, transitional, and low Reynolds number turbulent boundary layers are presented. Measurements were done in a low-speed, closed-loop wind tunnel with a freestream velocity of 100 ft/s and zero pressure gradient over a range of freestream turbulence intensities from 0.4 to 6 percent. The distributions of skin friction, heat transfer rate, and Reynolds shear stress were all consistent with previously published data. Reynolds analogy factors for momentum thickness Reynolds number, Re(sub theta) less than 2300 were found to be well predicted by laminar and turbulent correlations which accounted for an unheated starting length and uniform heat flux. A small dependence of turbulence results on the freestream turbulence intensity was observed.

Sohn, K. H.↗
DOE OSTI2026

Implementation of a High-Mach Integral Boundary Layer Method for Arbitrary Streamlined Body Geometry

The Momentum-Energy Integral Technique (MEIT) is an integral boundary layer method for the high-Mach flow regime used to approximate heat transfer and viscous force quantities of interest along streamlines of an inviscid flow solution on the surface of a flight vehicle. This method allows rapid mid-fidelity estimation of these quantities which would otherwise require a much more expensive viscous flow solution to produce. Integral boundary layer methods like MEIT have been around for decades, though usually only formulated for simple geometries such as 2-dimensional wing shapes or axi-symmetric nose shapes. The implementation discussed herein has been generalized to apply to any 3-dimensional streamlined body geometry through correct treatment of the curvilinear axes (streamline attached) momentum and energy entrainment terms, and handling of arbitrary stagnation region geometry. This implementation is provided as a software package for the Python environment, along with readers for common inviscid flow solution providers such as NASA’s CART3D flow solver.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1979

A new approach to the correlation of boundary layer mass transfer rates with thermal diffusion and/or variable properties

A rational approach to the correlation of boundary layer mass transport rates, applicable to many commonly encountered laminar flow conditions with thermal diffusion and/or variable properties, is outlined. The correlation scheme builds upon already available constant property blowing/suction solutions by introducing appropriate correction factors to account for the additional ('pseudo' blowing and source) effects identified with variable properties and thermal diffusion. Applications of the scheme to the particular laminar boundary layer mass transfer problems considered herein (alkali and transition metal compound vapor transport) indicates satisfactory accuracy up to effective blowing factors equivalent to about one third of the 'blow off' value. As a useful by-product of the variable property correlation, we extend the heat-mass transfer analogy, for a wide range of Lewis numbers, to include variable property effects.

Srivastava, R.↗
NASA NTRS1979

Generalized velocities in the outer region of hypersonic turbulent boundary layers

An attempt is made to show that the outer portion of the velocity profile of hypersonic turbulent boundary layers can be transformed so that the constants determined by a best fit to the law of the wake are in reasonable agreement with the wake constant for incompressible boundary layers at the same Reynolds number. Both y transformations (where y is distance from the surface) and velocity transformations produce velocity profiles which, with the proper choice of wall shear stress to give shear velocity, can be reduced to the incompressible law of the wall.

Watson, R. D.↗
NASA NTRS1980

Cycle II.5 aircraft aero-optical turbulent boundary-layer/shear-layer measurements

The aero-optical effects associated with propagating a laser beam through aircraft turbulent boundary layers and shear layers were examined. Observed laser optical performance levels were compared with those inferred from aerodynamic measurements of unsteady densities and correlation lengths within these random flows. Optical instrumentation included a fast shearing interferometer (FSI). A 9 cm diameter collimated helium neon laser beam made a double pass through the aircraft random flow via an airfoil mirror located one meter from the fuselage. Typical aircraft turbulent boundary layer thickness measured 0.3 meters. Averaging many FSI generated modulation transfer functions (MTFs) and Fourier transforming, this average yields the expected far field intensity degradation associated with an aircraft mounted laser system. Aerodynamic instrumentation included fine wire probes to measure unsteady temperature and mass flux. A laser doppler velocimeter measured unsteady velocity within the flows. An analysis of these data yielded point measurements of unsteady density and correlation length.

Gilbert, K.↗
NASA NTRS1996

On the Coupling Between a Supersonic Turbulent Boundary Layer and a Flexible Structure

A mathematical model and a computer code have been developed to fully couple the vibration of an aircraft fuselage panel to the surrounding flow field, turbulent boundary layer and acoustic fluid. The turbulent boundary layer model is derived using a triple decomposition of the flow variables and applying a conditional averaging to the resulting equations. Linearized panel and acoustic equations are used. Results from this model are in good agreement with existing experimental and numerical data. It is shown that in the supersonic regime, full coupling of the flexible panel leads to lower response and radiation from the panel. This is believed to be due to an increase in acoustic damping on the panel in this regime. Increasing the Mach number increases the acoustic damping, which is in agreement with earlier work.

Frendi, Abdelkader↗
NASA NTRS1985

The reservoir of ozone in the boundary layer of the eastern United States and its potential impact on the global tropospheric ozone budget

An analysis of available ozone data in the eastern two-thirds of the United States indicates that a substantial reservoir of ozone is present in the summertime. Five-year mean concentrations range from 40 to 65 ppbv. The reservoir covered an area of several million square kilometers and extends vertically from the surface to 1 to 2 km. The vertical distribution of ozone in the reservoir during midday supports a transport of additional ozone from the boundary layer to the free troposphere. Data are presented demonstrating the potential effect of transport by convective clouds and by the sea breeze circulation - mechanisms by which ozone may be transported out of the boundary layer into the free troposphere. The potential impact of this reservoir on the tropospheric ozone budget is discussed. It is shown that if less than half of the ozone mass in this reservoir is transported to the free troposphere, then the amount of ozone transported out of the boundary layer approximates the amount of ozone transported downward during a tropopause fold event.

Vukovich, F. M.↗
DOE OSTI2020

Dataset for "FLEXPART-WRF simulations to assess dust transport in the convective boundary layer at the Southern Great Plains site"

Soil dusts are an important source of aerosol in agricultural regions and can affect the Earth’s radiation budget through the modification of cloud properties, and in particular, through their ability to act as ice nucleating particles. In order to impact cloud properties, agricultural soil dusts need to be transported from the point of emission to cloud-relevant altitudes. Vertical transport within the planetary boundary layer is strongly controlled by turbulence and is challenging to represent accurately in regional and global models. Large-eddy simulations (LES) are run at resolutions capable of resolving most of the turbulent energy directly and can thus better simulate vertical transport. In this study, we leverage the LES ARM Symbiotic Simulation and Observation (LASSO) large-eddy simulations to simulate vertical transport of agricultural dust within the turbulent boundary layer using a modified version of the stochastic dispersion model FLEXPART-WRF. We find that the modified model is better capable of simulating particle transport due to turbulence, and that particle size was the greatest factor in determining particle lifetime. Individual meteorology and particle density had intermediate effects upon particle transport, while release height had little effect upon simulation results. Finally, we utilize a quasi-single column model (QSCM) approach to determine how our results compare to a parameterized treatment of turbulence. The QSCM simulations led to greater tracer transport out of the boundary layer, with ramifications for any studies utilizing a Lagrangian stochastic model to understand tracer dispersion. These results highlight the importance of accurately simulating turbulence for understanding particle transport.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1977

Separating and turbulent boundary layer calculations using polynomial interpretation

Higher order numerical methods derived from polynomial spline interpolation or Hermitian differencing are applied to a separating laminar boundary layer, i.e., the Howarth problem, and the turbulent flat plate boundary layer flow. Preliminary results are presented. It is found that accuracy equal to that of conventional second order accurate finite difference methods is achieved with many fewer mesh points and with reduced computer storage and time requirements.

Rubin, S. G.↗
NASA NTRS1995

Boundary layer blockage in expansion tube nozzles

The results of a first order perfect gas correction for the effects of the boundary layer formation within expansion tubes with nozzles are presented. The analytical model developed to describe the boundary layer formation within the expansion tube and an expansion nozzle located at the end of the acceleration tube is based on the Karman integral equations. The results of this analytical model are compared with experimental data from an expansion diffuser. The model provides a useful tool for the preliminary design of nozzles for such facilities.

Sudnitsin, Olga↗
NASA NTRS2002

Boundary Layer Transition Correlations and Aeroheating Predictions for Mars Smart Lander

Laminar and turbulent perfect-gas air, Navier-Stokes computations have been performed for a proposed Mars Smart Lander entry vehicle at Mach 6 over a free stream Reynolds number range of 6.9 x 10(exp 6/m to 2.4 x 10(exp 7)m(2.1 x 10(exp 6)/ft to 7.3 x 10(exp 6)ft) for angles-of-attack of 0-deg, 11-deg, 16-deg, and 20-deg, and comparisons were made to wind tunnel heating data obtained at the same conditions. Boundary layer edge properties were extracted from the solutions and used to correlate experimental data on the effects of heat-shield penetrations (bolt-holes where the entry vehicle would be attached to the propulsion module during transit to Mars) on boundary-layer transition. A non-equilibrium Martian-atmosphere computation was performed for the peak heating point on the entry trajectory in order to determine if the penetrations would produce boundary-layer transition by using this correlation.

Hollis, Brian R.↗
NASA NTRS1985

Drag characteristics of unsteady, perturbed boundary layer flows

A series of time-dependent numerical computations have been performed for the flow of an unsteady boundary layer over an embedded cavity, which is aligned normal to the flow direction. The unsteady flow is the result of the imposition of a Stuart vortex, at the inflow boundary of the computational domain, onto an otherwise unperturbed two-dimensional laminar boundary layer flow. This produces a strongly vortical, but spatially monochromatic, motion at inflow which is allowed to evolve downstream through the time-dependent numerical solution of appropriate conservation equations. As the imposed vortex evolves over the solid boundary, a weaker induced vortical motion is produced and together these perturbing motions interact with the fluid motion in the embedded cavity. An analysis of the pertinent dynamic variables as well as the time-dependent drag characteristics for this type of non-planar geometry is performed; with particular emphasis on the relative contribution of both pressure drag and frictional drag at various times in the evolution process.

Gatski, T. B.↗