SEARCH · Engineering Papers

Results for “blade”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

All sources NASA NTRS DOE OSTI

NASA NTRS1988

Acoustic measurements from a rotor blade-vortex interaction noise experiment in the German-Dutch Wind Tunnel (DNW)

Acoustic data are presented from a 40 percent scale model of the 4-bladed BO-105 helicopter main rotor, measured in the large European aeroacoustic wind tunnel, the DNW. Rotor blade-vortex interaction (BVI) noise data in the low speed flight range were acquired using a traversing in-flow microphone array. The experimental apparatus, testing procedures, calibration results, and experimental objectives are fully described. A large representative set of averaged acoustic signals is presented.

Martin, Ruth M.↗

NASA NTRS1988

Two-Equation Low-Reynolds-Number Turbulence Modeling of Transitional Boundary Layer Flows Characteristic of Gas Turbine Blades

The use of low Reynolds number (LRN) forms of the k-epsilon turbulence model in predicting transitional boundary layer flow characteristic of gas turbine blades is developed. The research presented consists of: (1) an evaluation of two existing models; (2) the development of a modification to current LRN models; and (3) the extensive testing of the proposed model against experimental data. The prediction characteristics and capabilities of the Jones-Launder (1972) and Lam-Bremhorst (1981) LRN k-epsilon models are evaluated with respect to the prediction of transition on flat plates. Next, the mechanism by which the models simulate transition is considered and the need for additional constraints is discussed. Finally, the transition predictions of a new model are compared with a wide range of different experiments, including transitional flows with free-stream turbulence under conditions of flat plate constant velocity, flat plate constant acceleration, flat plate but strongly variable acceleration, and flow around turbine blade test cascades. In general, calculational procedure yields good agreement with most of the experiments.

Schmidt, Rodney C.↗

NASA NTRS1988

Analysis of rotating flexible blades using MSC/NASTRAN

An overview is given of the use of MSC/NASTRAN in the analysis of rotating flexible blades. The geometrically nonlinear analysis using NASTRAN Solution Sequence 64 is discussed along with the determination of frequencies and mode shapes using Solution Sequence 63. Items unique to rotating blade analysis, such as setting angle, centrifugal softening effects, and hub flexibility, are emphasized.

Ernst, Michael A.↗

NASA NTRS1988

Recent advances in capacitance type of blade tip clearance measurements

Two recent electronic advances at NASA-Lewis that meet the blade tip clearance needs of a wide class of fans, compressors, and turbines are described. The first is a frequency modulated (FM) oscillator that requires only a single low cost ultrahigh frequency operational amplifier. Its carrier frequency is 42.8 MHz when used with a 61 cm long hermetically sealed coaxial cable. The oscillator can be calibrated in the static mode and has a negative peak frequency deviation of 400 kHz for a typical rotor blade. High temperature performance tests of the probe and 13 cm of the adjacent cable show good accuracy up to 600 C, the maximum which produces a clearance error of + or - 10 microns at a clearance of 500 microns. In the second advance, a guarded probe configuration allows a longer cable capacitance. The capacitance of the probe is part of a small time constant feedback in a high speed operational amplifier. The solution of the governing differential equation is applied to a ramp type of input. The results show an amplifier output that contains a term which is proportional to the derivative of the feedback capacitance. The capacitance is obtained by subtracting a balancing reference channel followed by an integration stage.

Barranger, John P.↗

NASA NTRS1988

Aeroelastic modeling of rotor blades with spanwise variable elastic axis offset: Classic issues revisited and new formulations

In response to a systematic methodology assessment program directed to the aeroelastic stability of hingeless helicopter rotor blades, improved basic aeroelastic reformulations and new formulations relating to structural sweep were achieved. Correlational results are presented showing the substantially improved performance of the G400 aeroelastic analysis incorporating these new formulations. The formulations pertain partly to sundry solutions to classic problem areas, relating to dynamic inflow with vortex-ring state operation and basic blade kinematics, but mostly to improved physical modeling of elastic axis offset (structural sweep) in the presence of nonlinear structural twist. Specific issues addressed are an alternate modeling of the delta EI torsional excitation due to compound bending using a force integration approach, and the detailed kinematic representation of an elastically deflected point mass of a beam with both structural sweep and nonlinear twist.

Bielawa, Richard L.↗

NASA NTRS1988

Probabilistic structural analysis to quantify uncertainties associated with turbopump blades

A probabilistic study of turbopump blades has been in progress at NASA Lewis Research Center for over the last two years. The objectives of this study are to evaluate the effects of uncertainties in geometry and material properties on the structural response of the turbopump blades to evaluate the tolerance limits on the design. A methodology based on probabilistic approach was developed to quantify the effects of the random uncertainties. The results indicate that only the variations in geometry have significant effects.

Nagpal, Vinod K.↗

NASA NTRS1988

Optical measurement of propeller blade deflections

A nonintrusive optical method for measurement of propeller blade deflections is described and evaluated. It does not depend on the reflectivity of the blade surface but only on its opaqueness. Deflection of a point at the leading edge and a point at the trailing edge in a plane nearly perpendicular to the pitch axis is obtained using a single light beam generated by a low-power helium-neon laser. Quantitative analyses are performed from taped signals on a digital computer. Averaging techniques are employed to reduce random errors. Measured deflections from a static and a high-speed test are compared with available predicted deflections which are also used to evaluate systematic errors.

Kurkov, Anatole P.↗

NASA NTRS1988

Optical measurement of unducted fan blade deflections

A nonintrusive optical method for measuring unducted fan (or propeller) blade deflections is described and evaluated. The measurement does not depend on blade surface reflectivity. Deflection of a point at the leading edge and a point at the trailing edge in a plane nearly perpendicular to the pitch axis is obtained with a single light beam generated by a low-power, helium-neon laser. Quantitiative analyses are performed from taped signals on a digital computer. Averaging techniques are employed to reduce random errors. Measured static deflections from a series of high-speed wind tunnel tests of a counterrotating unducted fan model are compared with available, predicted deflections, which are also used to evaluate systematic errors.

Kurkov, Anatole P.↗

NASA NTRS1987

The measurement of boundary layers on a compressor blade in cascade. II - Suction surface boundary layers

A one-component laser Doppler velocimeter (LDV) has been used to measure the two-dimensional, periodic flow field about a double circular arc, compressor blade in cascade. Eleven boundary layer profiles were taken on both the pressure and suction surfaces of the blade, and two were taken in the near wake. In this part of the study, the LDV system is described and the suction surface flow field is documented. The suction surface profiles appear to separate both at the leading edge and again somewhat beyond midchord; the leading edge separation apparently reattaches by 2.6 percent chord.

Deutsch, Steven↗

NASA NTRS1987

The measurement of boundary layers on a compressor blade in cascade. III - Pressure surface boundary layers and the near wake

A one-component laser Doppler velocimeter (LDV) has been used to measure the two-dimensional periodic flow field about a double circular arc, compressor blade in cascade. Eleven boundary layer profiles were taken on both the pressure and suction surfaces of the blade, and two profiles were taken in the near wake. In this part of the study, the detailed LDV studies are described. The measurements indicate that the onset of transition occurs near 60 percent chord. The lack of a logarithmic region in the data measured at 97.9 percent chord indicates that transition is not complete. The thin laminar boundary layers near the leading edge led to some measurement problems, characterized by large turbulence intensities, in using the LDV.

Deutsch, Steven↗

NASA NTRS1987

Correlation between ultrasonic velocity and density of ceramic turbine blades

A computer-aided ultrasonic velocity measurement system to detect small density variations in structural ceramic materials has been developed. Longitudinal wave ultrasonic velocity and density of ceramic turbine blades and bars were measured and statistically correlated. Density variations of 1 to 2 percent were reliably detected. Burst speed of ceramic blades was inversely proportional to the grain size of the material.

Khandelwal, P. K.↗

NASA NTRS1987

Thermal stresses of a wind turbine blade made of orthotropic material

This study is to investigate the thermal stress of a wind turbine blade made of wood composite material. First, the governing partial differential equation on heat conduction is stated, then, a finite element procedure using a variational approach is employed for the solution of the governing equation. Thus, the temperature field throughout the blade is determined. Next, based on the temperature field, a finite element procedure using potential energy approach is applied to determine the thermal stress field. A set of results is obtained through the use of a computer, which is considered to be satisfactory.

Fu, Kuan-Chen↗

NASA NTRS1988

Overview of numerical codes developed for predicted electrothermal deicing of aircraft blades

An overview of the deicing computer codes that have been developed at the University of Toledo under sponsorship of the NASA-Lewis Research Center is presented. These codes simulate the transient heat conduction and phase change occurring in an electrothermal deicier pad that has an arbitrary accreted ice shape on its surface. The codes are one-dimensional rectangular, two-dimensional rectangular, and two-dimensional with a coordinate transformation to model the true blade geometry. All modifications relating to the thermal physics of the deicing problem that have been incorporated into the codes will be discussed. Recent results of reformulating the codes using different numerical methods to increase program efficiency are described. In particular, this reformulation has enabled a more comprehensive two-dimensional code to run in much less CPU time than the original version. The code predictions are compared with experimental data obtained in the NASA-Lewis Icing Research Tunnel with a UH1H blade fitted with a B. F. Goodrich electrothermal deicer pad. Both continuous and cyclic heater firing cases are considered. The major objective in this comparison is to illustrate which codes give acceptable results in different regions of the airfoil for different heater firing sequences.

Keith, Theo G.↗

NASA NTRS1987

Free wake analysis of helicopter rotor blades in hover using a finite volume technique

A fully compressible method for determining helicopter rotor wake effects is described which computes the wake without requiring external specification of the wake, or separate computations for the wake and blade region. The method is a modification of a compressible finite volume Potential Flow technique, and it has been implemented in a program, HELIX I, for computing compressible rotor flow fields in hover with free wakes. Wake positions in substantial agreement with experiment have been calculated for cases including subsonic and transonic flows, high and low aspect ratios, and two- and four-bladed rotors.

Ramachandran, K.↗

NASA NTRS1988

Structural optimization with aeroelastic constraints of rotor blades with straight and swept tips

This paper describes a study in which structural optimization techniques are used to minimize the n/rev vertical hub shears in forward flight, subject to aeroelastic stability constraints and frequency placement constraints. A special technique is used to build a sequence of approximate, inexpensive to solve optimization problems, the solutions of which converge to the solution of the exact, expensive to solve optimization problem. Blade configurations with both straight and swept tips, and single- and double-cell cross sections are analyzed. The results show that the approach used in this study is very efficient, and produces improved designs with a very small number of blade aeroelastic analyses.

Celi, R.↗

NASA NTRS1988

Optimal placement of tuning masses for vibration reduction in helicopter rotor blades

Methods are presented for the reduction of helicopter rotor blade vibration through a formal mathematical optimization technique determination of optimum tuning mass sizes and locations; these are used as design variables that are systematically changed to achieve low values of shear without large mass penalty. Matrix expressions are obtained for the modal shaping parameter and modal shear amplitude that are required for FEM structural analysis of the blade as well as the optimization formulation. Sensitivity derivatives are also obtained. Three different optimization strategies are developed and tested.

Pritchard, Jocelyn I.↗

NASA NTRS1988

Evaluation of a turbine blade damper using an integral approach

An integrated experimental/analytical approach to friction damper design optimization in cases where gas turbine blade-response data are unavailable under actual engine operating conditions is presently applied to the case of a damper designed to relieve a blade-cracking problem on a liquid fuel rocket engine's turbopump. Attention is given to the experimental methods and analytical models used, as well as to the predicted damper performance. The inclusion of macroslip, microslip, and variable normal load effects was found to be necessary.

Kielb, Robert E.↗

NASA NTRS1988

Vortex shedding in high-speed compressor blade wakes

The wakes of highly loaded compressor blades are generally considered to be turbulent flows. Recent work has suggested that the blade wakes are dominated by a vortex streetlike structure. The experimental evidence supporting the wake vortex structure is reviewed. This structure is shown to redistribute thermal energy within the flowfield. The effect of the wake structure on conventional aerodynamic measurements of compressor performance is noted. A two-dimensional, time-accurate, viscous numerical simulation of the flow exhibits both vortex shedding in the wake and a lower-frequency flow instability that modulates the shedding. The numerical results are shown to agree quite well with the measurement from transonic compressor rotors.

Epstein, A. H.↗