SEARCH · Engineering Papers

Results for “Transducers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

All sources NASA NTRS DOE OSTI

NASA NTRS1973

Multiple pure tone noise generation and control.

The generation of multiple pure tones in supersonic fans is discussed. The theoretical results of Kurasaka are reviewed and compared with experimental data obtained on a 36-in. diameter, 1550 ft/sec, 1.6 pressure ratio fan. Detailed measurements on bow shock locations taken with pressure transducers indicate that blade to blade discrepancies are the source of MPT generation. The paper presents some experimental results on an attempt to reduce the shock strength, and subsequently the MPT's, through blade modifications. Other attempts at reducing the MPT's through wall treatment, high inlet flow Mach number, acoustically treated splitters - are discussed. Experimental data is presented on the validity of these noise reduction methods.

Benzakein, M. J.↗

NASA NTRS1974

Three-point bridge calibration with one resistor

Method calibrates transducer bridge curing unbalanced condition and line resistance errors are negligible. Series resistance method can be automated easily and controlled by 2-bit information source which provide 4 states for switches.

Harrison, D. R.↗

NASA NTRS1974

Electronic high pass filter

Ultra accurate filter is used with static type pressure transducers where it is desirable to extract low frequency dynamic signals from combined static and dynamic signal. System can be calibrated at any time with dc voltages.

Peterson, V. S.↗

NASA NTRS1974

Nondestructive testing of railroad wheels and rails by ultrasonics

Quality control of wheels and rails can be improved by using ultrasonic technique developed for measuring stresses in metallic materials. In addition, parts already in use can be tested and replaced if they are found to be unsafe. Test equipment includes two transducers.

Clotfelter, W. M.↗

NASA NTRS1975

Volume measuring system

Chamber is designed to be airtight; it includes face mask for person to breathe outside air so that he does not disturb chamber environment. Chamber includes piston to vary air volume inside. Also included are two microphone transducers which record pressure information inside chamber.

Oele, J. S.↗

NASA NTRS1973

Investigation of laser holographic interferometric techniques for structure inspection

The application of laser holographic interferometric techniques for nondestructive inspection of material structures commonly used in aerospace works is investigated. Two types of structures, composite plate and solid fuel rocket engine motor casing, were examined. In conducting the experiments, both CW HeNe gas lasers and Q-switched ruby lasers were used as light sources for holographic recording setups. Different stressing schemes were investigated as to their effectiveness in generating maximum deformation at regions of structural weakness such as flaws and disbonds. Experimental results on stressing schemes such as thermal stressing, pressurized stressing, transducer excitation, and mechanical impact are presented and evaluated.

Chu, W. P.↗

NASA NTRS1973

Thermomagnetic recording and magneto-optic playback system having constant intensity laser beam control

A system is developed for maintaining the intensity of a laser beam at a constant level in a thermomagnetic recording and magneto-optic playback system in which an isotropic film is heated along a continuous path by the laser beam for recording. As each successive area of the path is heated locally to the vicinity of its Curie point in the presence of a controlled magnetic field, a magneto-optic density is produced proportional to the amplitude of the controlled magnetic field. To play back the recorded signal, the intensity of the laser beam is reduced and a Faraday or Kerr effect analyzer is used, with a photodetector, as a transducer for producing an output signal.

Lewicki, G. W.↗

NASA NTRS1974

Phase protection system for ac power lines

The system described provides protection for phase sensitive loads from being or remaining connected to ac power lines whenever a phase reversal occurs. It comprises a solid state phase detection circuit, a dc power relay circuit, an ac-to-dc converter for energizing the relay circuit, and a bistable four terminal transducer coupled between the phase detection circuit and the power relay circuit, for controlling both circuits.

Wong, W. J.↗

NASA NTRS1973

Ultrasonic scanning system for in-place inspection of brazed tube joints

A miniaturized ultrasonic scanning system for nondestructive in-place, non-immersion testing of brazed joints in stainless-steel tubing is described. The system is capable of scanning brazed tube joints, with limited clearance access, in 1/4 through 5/8 inch union, tee, elbow and cross configurations. The system has the capability to detect defective conditions now associated with material density changes in addition to those which are depended upon density variations. The system includes a miniaturized scanning head assembly that fits around a tube joint and rotates the transducer around and down the joint in a continuous spiral motion. The C-scan recorder is similar in principle to conventional models except that it was specially designed to track the continuous spiral scan of the tube joint. The scanner and recorder can be operated with most commercially available ultrasonic flaw detectors.

Haynes, J. L.↗

NASA NTRS1973

Velocity control propulsion subsystem of the Radio Astronomy Explorer satellite for Goddard Space Flight Center

The Velocity Control Propulsion Subsystem (VCPS) was designed the propulsion required for trajectory and lunar orbit corrections of the spacecraft. A GFE clamp assembly physically attaches the VCPS to the spacecraft and the unit is ejected after completing the required corrections. The VCPS is physically and functionally separated from the spacecraft except for the electrical and telemetry interfaces. A GFE transtage provides the superstructure on which the VCPS is assembled. The subsystem consists of two 5 foot pound rocket engine assemblies, 4 propellant tanks, 2 latching valves, 2 fill and drain valves, a system filter, pressure transducer, gas and propellant manifolds and electrical heaters and thermostats. The RAE-B VCPS program covered the design, manufacture and qualification of one subsystem. This subsystem was to be manufactured, subjected to qualification tests; and refurbished, if necessary, prior to flight. The VCPS design and test program precluded the need for refurbishing the subsystem and the unit was delivered to GSFC at the conclusion of the program.

Braught, W.↗

NASA NTRS1974

Experimental studies of hypersonic boundary-layer transition and effects of wind tunnel disturbances

Boundary layer transition data on cones and free stream disturbance levels were measured in a hypersonic wind tunnel and Mach 8 variable density hypersonic tunnel. Transition data were obtained by using different conical models and techniques for detecting the location of transition. The disturbance levels were measured by using hot wire anemometry and pressure transducers. The transition Reynolds numbers obtained from the tests correlated well when the fluctuating pressures measured at the surface of conical models were used as a correlating parameter.

Stainback, P. C.↗

NASA NTRS1974

An experimental investigation of the damping contribution of an elastomeric ablator on aluminum beams

Damping results are presented for an elastometric ablation material bonded to an aluminum alloy substrate. Tests were conducted on aluminum beams 0.159, 0.318, and 0.476 cm thick, and with and without an ablator. Ablation-material thickness varied from 0.159 to 0.953 cm. Comparative damping data were obtained by using variations of the free-free beam technique with strain gages and piezoelectric transducers. Of the two test arrangements employed, the technique using strain gages produced results that indicated less restraint of the beams. Ablation material, in thicknesses less than 1 cm, substantially increased the damping parameter of the aluminum beams.

Howell, W. E.↗

NASA NTRS1973

A case study of technology transfer: Rehabilitative engineering at Rancho Los Amigos Hospital

The transfer of NASA technolgy to rehabilitative applications of artificial limbs is studied. Human factors engineering activities range from orthotic manipulators to tiny dc motors and transducers to detect and transmit voluntary control signals. It is found that bicarbon implant devices are suitable for medical equipment and artificial limbs because of their biological compatibility with human body fluids and tissues.

Hildred, W.↗

NASA NTRS1973

Development of an externally powered prosthetic hook for amputees

The powered hook with trigger finger appears to be a useful adaptation of a terminal device for an amputee when performing vocational activities involving the use of a powered tool requiring a trigger control. The proportional control system includes transducers and amplifiers and appears to have widespread application for control of any external power, whether it be in the orthotic or prosthetic field.

Karchak, A., Jr.↗

NASA NTRS1974

LC-oscillator with automatic stabilized amplitude via bias current control

A stable excitation supply for measurement transducers is described. It consists of a single-transistor oscillator with a coil connected to the collector and a capacitor connected from the collector to the emitter. The output of the oscillator is rectified and the rectified signal acts as one input to a differential amplifier; the other input being a reference potential. The output of the amplifier is connected at a point between the emitter of the transistor and ground. When the rectified signal is greater than the reference signal, the differential amplifier produces a signal of polarity to reduce bias current and, consequently, amplification.

Hamlet, J. F.↗

NASA NTRS1974

Instruments for measuring radiant thermal fluxes

An absolute two-sided radiometer, designed on the principle of replacing absorbed radiant energy with electrical energy, is described. The sensitive element of the detector is a thermoelectric transducer of thermal flux. The fabrication technology, methods of measurement, technical characteristics, and general operation of the instrument are presented.

Gerashenko, O. A.↗

NASA NTRS1974

Vibration and noise measuring instruments built in the RSR

The demands placed upon vibration and noise measuring instruments are discussed. The instruments that are now being manufactured in the RSR are described, as well as those that are being made ready for manufacture, namely: the VP-3 portable vibrometer, the N2103 precision electronic vibrometer, the N2103 B sonometric preamplifier, as well as vibration transducers of the electrodynamic and piezoelectric types.

Georgescu, I.↗

NASA NTRS1974

Photoelectronic vibrometer with polarized light

A seismic torsiometer is described which is based on the reception by a photosensitive transducer of a light flux modulated by a relative rotation of the optical axes of two polaroids. The torsional vibrations of the polaroid fixed to the shaft are transmitted to the other polaroid (which at the same time is the seismic mass of the apparatus) by means of elastic lamellas. The device can work as accelerometer, vibrometer or frequency meter, depending on the value of the ratio between the proper oscillation frequency of the seismic system and the measured vibration frequency.

Kremmer, I.↗