Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

A study of structural concepts for ultralightweight spacecraft

Structural concepts for ultralightweight spacecraft were studied. Concepts for ultralightweight space structures were identified and the validity of heir potential application in advanced spacecraft was assessed. The following topics were investigated: (1) membrane wrinkling under pretensioning; (2) load-carrying capability of pressurized tubes; (3) equilibrium of a precompressed rim; (4) design of an inflated reflector spacecraft; (5) general instability of a rim; and (6) structural analysis of a pressurized isotensoid column. The design approaches for a paraboloidal reflector spacecraft included a spin-stiffened design, both inflated and truss central columns, and to include both deep truss and rim-stiffened geodesic designs. The spinning spacecraft analysis is included, and the two truss designs are covered. The performances of four different approaches to the structural design of a paraboloidal reflector spacecraft are compared. The spinning and inflated configurations result in very low total masses and some concerns about their performance due to unresolved questions about dynamic stability and lifetimes, respectively.

Miller, R. K.↗

Impact of magnetic isolation on pointing system performance in the presence of structural flexibility

The inertial pointing stability of a gimbal pointing system (AGS) was compared with a magnetic pointing/gimbal followup system (ASPS), under certain conditions of system structural flexibility and disturbance inputs from the gimbal support structure. Separate 3 degree-of-freedom (3DOF) linear models based on NASTRAN modal flexibility data for the gimbal and support structures were generated for the ASPS configurations. Using the models inertial pointing control loops providing 6dB of gain margin and 45 deg of phase margin were defined for each configuration. The pointing loop bandwidth obtained for the ASPS is more than twice the level achieved for the AGS configuration. The AGS limit is attributed to the gimbal and support structure flexibility. As a result of the higher ASPS pointing loop bandwidth and the disturbance rejection provided by the magnetic isolation ASPS pointing performane is significantly better than that of the AGS system. The low frequency peak of the ASPS transfer function from base disturbance to payload angular motion is almost 60dB lower than AGS low frequency peak.

Seller, J.↗

Composite Loads Spectra for Select Space Propulsion Structural Components: Probabilistic Load Model Development

This effort is in support of the development of the expert system of computer codes to predict the loads on select structural components of a space propulsion engine. The development will be based primarily on the space shuttle main engine (SSME) test data base. Because of random variations of the many different sources of the loadings on the selected structural components and transients, a probabilistic approach to the problems was adopted. The goal of this task is to characterize all of the individual sources of loads at critical structural locations, such as the turbine blades, the transfer ducts, and liquid oxygen posts, using state-of-the-art probabilistic methods with varying levels of sophistication. The second phase of this work is the development of a composite load model based on a probabilistic synthesis of the individual load model previously developed. This model will be based on the stochastic combination of the load variables and not on the physical process for the combination of the individual loads to the composite load seen by the selected structural components.

Kurth, R.↗

On the accuracy of modelling the dynamics of large space structures

Proposed space missions will require large scale, light weight, space based structural systems. Large space structure technology (LSST) systems will have to accommodate (among others): ocean data systems; electronic mail systems; large multibeam antenna systems; and, space based solar power systems. The structures are to be delivered into orbit by the space shuttle. Because of their inherent size, modelling techniques and scaling algorithms must be developed so that system performance can be predicted accurately prior to launch and assembly. When the size and weight-to-area ratio of proposed LSST systems dictate that the entire system be considered flexible, there are two basic modeling methods which can be used. The first is a continuum approach, a mathematical formulation for predicting the motion of a general orbiting flexible body, in which elastic deformations are considered small compared with characteristic body dimensions. This approach is based on an a priori knowledge of the frequencies and shape functions of all modes included within the system model. Alternatively, finite element techniques can be used to model the entire structure as a system of lumped masses connected by a series of (restoring) springs and possibly dampers. In addition, a computational algorithm was developed to evaluate the coefficients of the various coupling terms in the equations of motion as applied to the finite element model of the Hoop/Column.

Diarra, C. M.↗

Control of flexible structures

The requirements for future space missions indicate that many of these spacecraft will be large, flexible, and in some applications, require precision geometries. A technology program that addresses the issues associated with the structure/control interactions for these classes of spacecraft is discussed. The goal of the NASA control of flexible structures technology program is to generate a technology data base that will provide the designer with options and approaches to achieve spacecraft performance such as maintaining geometry and/or suppressing undesired spacecraft dynamics. This technology program will define the appropriate combination of analysis, ground testing, and flight testing required to validate the structural/controls analysis and design tools. This work was motivated by a recognition that large minimum weight space structures will be required for many future missions. The tools necessary to support such design included: (1) improved structural analysis; (2) modern control theory; (3) advanced modeling techniques; (4) system identification; and (5) the integration of structures and controls.

Russell, R. A.↗

Proceedings of the Workshop on Identification and Control of Flexible Space Structures, Volume 2

The results of a workshop on identification and control of flexible space structures held in San Diego, CA, July 4 to 6, 1984 are discussed. The main objectives of the workshop were to provide a forum to exchange ideas in exploring the most advanced modeling, estimation, identification and control methodologies to flexible space structures. The workshop responded to the rapidly growing interest within NASA in large space systems (space station, platforms, antennas, flight experiments) currently under design. Dynamic structural analysis, control theory, structural vibration and stability, and distributed parameter systems are discussed.

Rodriguez, G.↗

Parametric Stiffness Control of Flexible Structures

An unconventional method for control of flexible space structures using feedback control of certain elements of the stiffness matrix is discussed. The advantage of using this method of configuration control is that it can be accomplished in practical structures by changing the initial stress state in the structure. The initial stress state can be controlled hydraulically or by cables. The method leads, however, to nonlinear control equations. In particular, a long slender truss structure under cable induced initial compression is examined. both analytical and numerical analyses are presented. Nonlinear analysis using center manifold theory and normal form theory is used to determine criteria on the nonlinear control gains for stable or unstable operation. The analysis is made possible by the use of the exact computer algebra system MACSYMA.

Moon, F. C.↗

Vibrational Stabilization of Flexible Structures

It has been demonstrated that a high frequency excitation (HFE) field significantly changes the fundamental properties of mechanical systems. The most important contribution of HFE is the stiffening effect of an elastic continuum in the direction of the wave vector. This effect allows control of stiffness in any selected direction by the corresponding changes in the intensity of HFE. This new approach can be effective for large flexible space structures. Such an approach may prove to be very practical in the sense that large structures need to be made as flimsy as possible for low cost under ordinary situations. However, for certain operations such as development, orbital transfer, docking, and other circumstances, it would be vital to have a means of temporarily stiffening certain structural members. If the structure was designed to meet these occasional loads without temporary stiffening, it would be considerably more massive and more expensive.

Zak, M.↗

Chemical structure of interfaces

The interfacial structure of silicon/dielectric and silicon/metal systems is particularly amenable to analysis using a combination of surface spectroscopies together with a variety of chemical structures of Si/SiO2, Si/SiO2Si3N4, Si/Si2N2O, Si/SiO2/Al, and Si/Native Oxide interfaces using high resolution (0.350 eV FWHM) X ray photoelectron spectroscopy. The general structure of these dielectric interfaces entails a monolayer chemical transition layer at the Si/dielectric boundary. Amorphous Si substrates show a wide variety of hydrogenated Si and Si(OH) sub x states that are not observed in thermal oxidation of single crystal material. Extended SiO2 layers greater than 8 A in thickness are shown to be stoichiometric SiO2, but to exhibit a wide variety of local network structures. In the nitrogen containing systems, an approach to stoichiometric oxynitride compounds with interesting impurity and electron trapping properties are seen. In native oxides, substantial topographical nonuniformity in oxide thickness and composition are found. Analysis of metal/oxide interfacial layers is accomplished by analytical removal of the Si substrate by UHV XeF2 dry etching methods.

Grunthaner, F. J.↗

Detection of internal structure by scattered light intensity: Application to kidney cell sorting

Scattered light measurements in flow cytometry were sucessfully used to distinguish cells on the basis of differing morphology and internal structure. Differences in scattered light patterns due to changes in internal structure would be expected to occur at large scattering angles. Practically, the results of these calculations suggest that in experimental situations an array of detectors would be useful. Although in general the detection of the scattered light intensity at several intervals within the 10 to 60 region would be sufficient, there are many examples where increased sensitivity could be acheived at other angles. The ability to measure at many different angular intervals would allow the experimenter to empirically select the optimum intervals for the varying conditions of cell size, N/C ratio, granule size and internal structure from sample to sample. The feasibility of making scattered light measurements at many different intervals in flow cytometry was demonstrated. The implementation of simplified versions of these techniques in conjunction with independant measurements of cell size could potentially improve the usefulness of flow cytometry in the study of the internal structure of cells.

Goolsby, C. L.↗

Research and development activities in unified control-structure modeling and design

Results of work sponsored by JPL and other organizations to develop a unified control/structures modeling and design capability for large space structures is presented. Recent analytical results are presented to demonstrate the significant interdependence between structural and control properties. A new design methodology is suggested in which the structure, material properties, dynamic model and control design are all optimized simultaneously. The development of a methodology for global design optimization is recommended as a long term goal. It is suggested that this methodology should be incorporated into computer aided engineering programs, which eventually will be supplemented by an expert system to aid design optimization. Recommendations are also presented for near term research activities at JPL. The key recommendation is to continue the development of integrated dynamic modeling/control design techniques, with special attention given to the development of structural models specially tailored to support design.

Nayak, A. P.↗

Selfsimilar time dependent shock structures

Diffusive shock acceleration as an astrophysical mechanism for accelerating charged particles has the advantage of being highly efficient. This means however that the theory is of necessity nonlinear; the reaction of the accelerated particles on the shock structure and the acceleration process must be self-consistently included in any attempt to develop a complete theory of diffusive shock acceleration. Considerable effort has been invested in attempting, at least partially, to do this and it has become clear that in general either the maximum particle energy must be restricted by introducing additional loss processes into the problem or the acceleration must be treated as a time dependent problem (Drury, 1984). It is concluded that stationary modified shock structures can only exist for strong shocks if additional loss processes limit the maximum energy a particle can attain. This is certainly possible and if it occurs the energy loss from the shock will lead to much greater shock compressions. It is however equally possible that no such processes exist and we must then ask what sort of nonstationary shock structure develops. The ame argument which excludes stationary structures also rules out periodic solutions and indeed any solution where the width of the shock remains bounded. It follows that the width of the shock must increase secularly with time and it is natural to examine the possibility of selfsimilar time dependent solutions.

Beck, R.↗

Ground test experience with large composite structures for commercial transports

The initial ground test of each component resulted in structural failure at less than ultimate design loads. While such failures represent major program delays, the investigation and analysis of each failure revealed significant lessons for effective utilization of composites in primary structure. Foremost among these are secondary loads that produce through-the-thickness forces which may lead to serious weaknesses in an otherwise sound structural design. The sources, magnitude, and effects of secondary loads need to be thoroughly understood and accounted for by the designers of composite primary aircraft structures.

Bohon, H. L.↗

Finite element thermal-structural analyses of a cable-stiffened orbiting antenna

Finite element thermal-structural analyses of a cable-stiffened orbiting antenna are presented. The determination of prestresses in the antenna is described first. Heating and thermal analyses for orbiting space structures are then discussed briefly. Structural deformations and stresses are presented for three finite element structural analysis approaches: (1) small deflections, (2) stress-stiffening, and (3) large deflections. The accuracy of the three analysis approaches is evaluated for the orbiting antenna at different prestress levels.

Thornton, E. A.↗

Artificial plasma density structures produced by energetic electron beams from rockets and spacecraft

Recent rocket and Space Shuttle experiments have demonstrated the capability to launch electron beams of moderate power (100 W to 10 kW) into the earth's ionosphere and magnetosphere. This letter describes how such beams, when fired from rockets or satellites, can create significant ionization in the E- and F-regions of the ionosphere. Through proper selection of beam-related parameters, an interesting variety of plasma density structures, including plasma sheets and plasma filaments, can be created and studied over periods of 30 minutes to 1 hour, depending on the rate of plasma recombination and the density of the ambient plasma. Observations of these structures can give new information relating to the physics of plasma density structures in the ionosphere, and the effects these features have upon the scattering of radio waves. It is also possible that observations of the density structures will provide a new means for studying neutral winds and electrodynamic phenomena in the ionosphere.

Banks, P. M.↗

Flexibility of space structures makes design shaky

An evaluation is made of the development status of high stiffness space structures suitable for orbital construction or deployment of large diameter reflector antennas, with attention to the control system capabilities required by prospective space structure system types. The very low structural frequencies typical of very large, radio frequency antenna structures would be especially difficult for a control system to counteract. Vibration control difficulties extend across the frequency spectrum, even to optical and IR reflector systems. Current research and development efforts are characterized with respect to goals and prospects for success.

Hearth, D. P.↗

Structure and dynamics of Saturn's atmosphere

The large-scale structure and dynamics of Saturn's atmosphere, as revealed in the visible markings, wind patterns, and horizontal variation of temperature, are discussed. The large-scale thermal structure is addressed, including the mean vertical structure and the seasons and jets of the horizontal temperature structure. Earth-based and Voyager wind observations are used to discuss the internal rate of rotation, the zonal wind profile, the eddies, and the eddy transport. Dynamic models of the atmospheric circulation are reviewed, discussing the depth of the zonal flow, upwelling and downwelling, deep convection, eddy-mean flow interactions, long-lived ovals, and the zonal velocity profile.

Ingersoll, A. P.↗

The microwave structure of hot coronal loops

The thermal cyclotron emission from model dipole magnetic loops is computed. It is shown that a simple, isothermal dipole loop can show a great deal of spatial and polarization structure at microwave frequencies. This structure is sensitive to the observation frequency and angle of observation. Two qualitatively distinct microwave loop structures can be distinguished: (1) 'thin loop,' observed as a string of independent microwave peaks, corresponding to different harmonics of the local electron gyrofrequency; and (2) 'thick loop,' the harmonics are merged, so that a more continuous microwave structure is observed. It is shown that the presence of an external plasma can result in a change in the observed mode of polarization along one leg of a loop, without a change in the sign of the line-of-sight magnetic field. Models such as these, along with high-resolution microwave and related observations, can provide an excellent diagnostic of the magnetic and plasma properties of coronal loops.

Holman, G. D.↗