Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STABILIZATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Dimensionless scalings of confinement, heat transport and pedestal stability in JET-ILW and comparison with JET-C

Three dimensionless scans in the normalized Larmor radius ρ*, normalized collisionality ν* and normalized plasma pressure β have been performed in JET with the ITER-like wall (JET-ILW). The normalized energy confinement and the thermal diffusivity exhibit a scaling with ρ* consistent with the earlier results obtained in the carbon wall JET (JET-C) and with a gyro-Bohm scaling. In the pedestal, experimental results show that the stability is not dependent on ρ*, qualitatively in agreement with the peeling–ballooning (P–B) model. The ν* dimensionless scaling shows that JET-ILW normalized confinement has a stronger dependence on collisionality than JET-C. This leads to a reduction of the difference in the confinement between JET-ILW and JET-C to ≈ 10% at low ν*. The pedestal stability shows an improvement with decreasing ν*. This is ascribed to the increase of the bootstrap current, to the reduction of the pedestal width and to the reduction of the relative shift between pedestal density and temperature position. The β dimensionless scan shows that, at low collisionality, JET-ILW normalized confinement has no clear dependence with β, in agreement with part of the earlier scalings. At high collisionality, a reduction of the normalized confinement with increasing β is observed. This behaviour is driven mainly by the pedestal where the stability is reduced with increasing β. Finally, the P–B analysis shows that the stability reduction with increasing β at high ν* is due to the destabilizing effect of the increased relative shift.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

ELM-free H-mode phase and decoupling of peeling–ballooning stability boundary in the MAST Upgrade tokamak

A linear magnetohydrodynamic (MHD) peeling–ballooning stability analysis of the edge-localized mode (ELM)-free phase of a MAST Upgrade (MAST-U) H-mode plasma is presented. In contrast to other similar discharges, #47018 is found to have a significantly higher and wider pedestal during its ELM-free H-mode phase that lasts for approximately 80 ms; this is made possible by the reduced core MHD mode activity on the q = 2 surface. During this period, there is sustained decoupling of peeling and ballooning branches of the stability boundary on J–α space, opening an access channel to the second stability regime with higher peaks in pedestal current density $J_{\mathrm{N,ped}}$ and pressure gradient (α). Such decoupling of the stability boundary has not previously been observed in MAST-U H-modes, and if such a condition can be readily reproduced, it opens a wide range of opportunities for MAST-U to explore low-collisionality peeling-limited pedestal regimes as well as advanced scenarios such as quiescent H-modes that are relevant to future reactors such as STEP and ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effects of stabilizer strength on the delamination strength of ReBCO coated conductors

Delamination strengths (DSs) of ReBCO tapes were evaluated using a transverse tensile anvil test. This study first demonstrated that the electromechanical DS is nearly equivalent to the purely mechanical DS for ReBCO tapes exhibiting abrupt delamination behavior. Mechanical DS was then examined for tapes with and without stabilizer edges to assess the influence of stabilizer strength. Scanning electron microscopy/energy-dispersive x-ray spectroscopy analysis revealed the delamination sites and crack propagation in ReBCO tapes. Further investigation revealed that the DS of ReBCO tapes is primarily determined by two factors: (1) interfacial bonding strength between the layers and (2) mechanical strength of the stabilizer edges. These findings point to a potential approach to enhancing DS by increasing the strength of the stabilizer (e.g. by optimizing the Cu electroplating process).

Cu stabilizer↗

Successfully combining SUGRA hybrid inflation and moduli stabilization

Inflation and moduli stabilization mechanisms work well independently, and many string-motivated supergravity models have been proposed for them. However, a complete theory will contain both, and there will be (gravitational) interactions between the two sectors. These give corrections to the inflaton potential, which generically ruin inflation. This holds true even for fine-tuned moduli stabilization schemes. Following a suggestion by Achucarro and Sousa (2007 Preprint 0712.3460), we show that a viable combined model can be obtained if it is the Kaehler functions (G = K+ln|W|{sup 2}) of the two sectors that are added, rather than the superpotentials (as is usually done). Interaction between the two sectors does still impose some restrictions on the moduli stabilization mechanism, which are derived. Significantly, we find that the (post-inflation) moduli stabilization scale no longer needs to be above the inflationary energy scale.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Two-field Kaehler moduli inflation in large volume moduli stabilization

In this paper we present a two-field inflation model, which is distinctive in having a non-canonical kinetic Lagrangian and comes from the large volume approach to the moduli stabilization in flux compactification of type IIB superstring on a Calabi-Yau orientifold with h{sup (1,2)}>h{sup (1,1)}{>=}4. The Kaehler moduli are classified as the volume modulus, heavy moduli and two light moduli. The axion-dilaton, complex structure moduli and all heavy Kaehler moduli including the volume modulus are frozen by a non-perturbatively corrected flux superpotential and the {alpha}{sup '}-corrected Kaehler potential in the large volume limit. The minimum of the scalar potential at which the heavy moduli are stabilized provides the dominant potential energy for the surviving light Kaehler moduli. We consider a simplified case where the axionic components in the light Kaehler moduli are further stabilized at the potential minimum and only the geometrical components are taken as scalar fields to drive an assisted-like inflation. For a certain range of moduli stabilization parameters and inflation initial conditions, we obtain a nearly flat power spectrum of the curvature perturbation, with n{sub s} Almost-Equal-To 0.96 at Hubble exit, and an inflationary energy scale of 3 Multiplication-Sign 10{sup 14} GeV. In our model, there is significant correlation between the curvature and isocurvature perturbations on super-Hubble scales, so at the end of inflation a great deal of the curvature power spectrum originates from this correlation.

79 ASTRONOMY AND ASTROPHYSICS↗

Thermodynamic and dynamical stability of Freund-Rubin compactification

We investigate stability of two branches of Freund-Rubin compactification from thermodynamic and dynamical perspectives. Freund-Rubin compactification allows not only trivial solutions but also warped solutions describing warped product of external de Sitter space and internal deformed sphere. We study dynamical stability by analyzing linear perturbations around solutions in each branch. Also we study thermodynamic stability based on de Sitter entropy. We show complete agreement of thermodynamic and dynamical stabilities of this system. Finally, we interpret the results in terms of effective energy density in the four-dimensional Einstein frame and discuss cosmological implications.

79 ASTRONOMY AND ASTROPHYSICS↗

Kinetic equilibrium reconstruction and the impact on stability analysis of KSTAR plasmas

High fidelity kinetic plasma equilibrium reconstructions are an essential requirement for accurate stability and disruption prediction analyses to support continuous operation of high beta tokamak plasmas. The present kinetic equilibrium reconstructions of plasmas in the KSTAR device include plasma density and temperature profiles from Thomson scattering and ion temperature from charge exchange spectroscopy diagnostics, and allowance for fast particle pressure. In addition, up to 25 channels of motional Stark effect diagnostic data are used to constrain the magnetic field pitch angle profile in the plasma to produce a reliable computation of the safety factor, q, profile. In this work, H-mode plasmas exhibit clear pedestal characteristics in the reconstructed pressure profile compared to internal transport barrier or L-mode plasmas. The plasma configuration and vertical position of inner strike points are validated by CCD and infrared camera images. Ideal and resistive magnetohydrodynamic (MHD) stability analyses using the DCON and resistive DCON codes utilize these kinetic equilibrium reconstructions to compare to experimental plasma stability. Equilibria with sufficiently low convergence error can provide reliable computation of ideal and resistive MHD stability analysis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Theoretical study of the Alfven eigenmode stability in CFETR steady state discharges

The aim of this study is to analyze the stability of Alfven eigenmodes (AE) in the China Fusion Engineering Test Reactor (CFETR) plasma for steady state operations. The analysis is done using the gyro-fluid code FAR3d including the effect of the acoustic modes, EP finite Larmor radius damping effects and multiple energetic particle populations. Two high poloidal β scenarios are studied with respect to the location of the internal transport barrier (ITB) at r/a ≈ 0.45 (case A) and r/a ≈ 0.6 (case B). Both operation scenarios show a narrow TAE gap between the inner-middle plasma region and a wide EAE gap all along the plasma radius. In this work, the AE stability of CFETR plasmas improves if the ITB is located inwards, case A, showing AEs with lower growth rates with respect to the case B. The AEs growth rate is smaller in the case A because the modes are located in the inner-middle plasma region where the stabilizing effect of the magnetic shear is stronger with respect to the case B. Multiple EP populations effects (NBI driven EP + alpha articles) are negligible for the case A, although the simulations for the case B show a stabilizing effect of the NBI EP on the n = 1 BAE caused by α particles during the thermalization process. If the FLR damping effects are included in the simulations, the growth rate of the EAE/NAE decreases up to 70%, particularly for n > 3 toroidal families. Low n AEs (n < 6) show the largest growth rates. On the other hand, high n modes (n = 6 to 15) are triggered in the frequency range of the NAE, strongly damped by the FLR effects.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Direct preemptive stabilization of $m,n$ = 2,1 neoclassical tearing modes by electron cyclotron current drive in the DIII-D low-torque ITER baseline scenario

We report the first preemptive direct stabilization of $m,n$ = 2,1 neoclassical tearing modes (NTMs) in DIII-D low-torque ITER baseline scenario plasmas by electron cyclotron waves. These experiments strongly support that the observed stabilization is achieved by replacing the missing bootstrap current in the island by electron cyclotron current drive (ECCD). These plasmas (with and without ECCD) are stable to 2,1 NTMs when the differential rotation between the q = 1 and q = 2 surfaces (Δf 1,2 ) is sustained above a critical value (Δf CRIT ≈ 1 kHz), but those evolving to low differential rotation (Δf 1,2 < Δf CRIT ) routinely develop a disruptive 2,1 island at the time and frequency of a sawtooth precursor. Preemptive, local and direct stabilization by ECCD is tested by scanning the current drive amplitude and location inside and outside of the q = 2 rational surface shot by shot. Analysis of only low differential rotation time windows, i.e. when stabilization from Δf 1,2 is absent, shows focused ECCD at q = 2 prevents the onset of 2,1 NTMs. These results are important, as they give the first demonstration of disruptive NTM control by ECCD in the plasma scenario planned for ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Aeroservoelastic Stability of a Floating Wind Turbine

The problem of negative damping undermines the aeroservoelastic stability of floating offshore wind turbines. The negative damping problem is most prevalent around rated wind speed, where the sensitivity of thrust to wind speed is the largest. This paper investigates the implementation of peak shaving, a controller feature that limits the rated thrust by pitching the blades before rated wind speed is reached. Two controller designs are investigated: a de-tuned controller and a nacelle-feedback controller. A time-domain metric is defined, inspired by Lyapunov theory, in order to compute and assess the stability of floating offshore wind turbines. The model of the International Energy Agency 15-MW reference wind turbine mounted on the University of Maine VolturnUS-S floater is simulated in HAWC2 with the National Renewable Energy Laboratory reference open-source controller. Peak shaving is applied to the two controller designs and stability is assessed. According to the chosen metric, peak shaving does not improve the stability of the system. This is due to the trade-off between loads and error tracking: although the loads and displacements in the fore-aft direction of the turbine are reduced, the rotor-speed tracking is poorer, which increases the shaft torsion fatigue load.

17 WIND ENERGY↗

Proteome-wide analysis of protein stability in Escherichia coli under acid stress

Knowledge of protein acid sensitivity remains sparse and is largely derived from low-throughput, enzyme-specific assays. We used a scalable framework to map acid stability across the Escherichia coli proteome to assess the acid stability of 1,675 unique proteins, estimating pH 50 values for over 90% of them. The parameter pH50 was defined as the pH value at which only 50% of the initial protein remains in solution following acid treatment. Proteome-wide pH 50 values ranged from 2.28 to 6.33 (median 5.11). Approximately 9% of detected proteins remained stable across all tested pH conditions. Our results align with published data and the assay of citrate synthase (GltA) performed here. Protein acid stability differed significantly by subcellular localization: periplasmic proteins were relatively more abundant in the acid-stable group, cytoplasmic proteins were abundant at pH 50 values 4.5–5.5, and inner membrane proteins at higher pH 50 between 5.5 and 6.0. Outer membrane proteins were too few to draw strong conclusions regarding enrichment within specific pH 50 groups. Notably, the periplasmic binding protein of the molybdate ABC transporter (ModA), was enriched after incubation at low pH. Estimated pH 50 values showed no correlation with protein isoelectric point and molecular weight. Together, this work provides the first proteome-wide map of protein acid stability and establishes a general framework for studying different chemical stressors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Extreme nonlinear response of ultranarrow optical transitions in cavity QED for laser stabilization

We explore the potential of direct spectroscopy of ultranarrow optical transitions of atoms localized in an optical cavity. In contrast to stabilization against a reference cavity, which is the approach currently used for the most highly stabilized lasers, stabilization against an atomic transition does not suffer from Brownian thermal noise. Spectroscopy of ultranarrow optical transitions in a cavity operates in a very highly saturated regime in which nonlinear effects such as bistability play an important role. From the universal behavior of the Jaynes-Cummings model with dissipation, we derive the fundamental limits for laser stabilization using direct spectroscopy of ultranarrow atomic lines. We find that, with current lattice clock experiments, laser linewidths of about 1 mHz can be achieved in principle, and the ultimate limitations of this technique are at the 1 {mu}Hz level.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Stability of metallic thin film with free electron model

The stability of metallic thin lms is studied with free electron model, which is popularly known as model of \particle in a box". A detailed theoretical framework is presented, along with discussion on typical metals, such as Pb, Al, Ag, Na, and Be. This simple model is found to be able to describe well the oscillation pattern of stability for continuous metallic lms. In particular, it yields even-odd oscillations in the stability of Pb(111) lm, consistent with both experimental observation and ab initio results. However, the free electron model is too crude to predict at what thickness the lm is stable. The lm stability is further examined with a model of \particle in a corrugated box", where a lattice potential is added along the vertical direction of the lm. The e ect of lattice potential is found not substantial.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Jacobi stability of the vacuum in the static spherically symmetric brane world models

We analyze the stability of the structure equations of the vacuum in the brane world models, by using both the linear (Lyapunov) stability analysis, and the Jacobi stability analysis, the Kosambi-Cartan-Chern theory. In the brane world models the four-dimensional effective Einstein equations acquire extra terms, called dark radiation and dark pressure, respectively, which arise from the embedding of the three-brane in the bulk. Generally, the spherically symmetric vacuum solutions of the brane gravitational field equations have properties quite distinct as compared to the standard black hole solutions of general relativity. We close the structure equations by assuming a simple linear equation of state for the dark pressure. In this case the vacuum is Jacobi stable only for a small range of values of the proportionality constant relating the dark pressure and the dark radiation. The unstable trajectories on the brane behave chaotically, in the sense that after a finite radial distance it would be impossible to distinguish the trajectories that were very near each other at an initial point. Hence the Jacobi stability analysis offers a powerful method for constraining the physical properties of the vacuum on the brane.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Null energy condition violation and classical stability in the Bianchi I metric

The stability of isotropic cosmological solutions in the Bianchi I model is considered. We prove that the stability of isotropic solutions in the Bianchi I metric for a positive Hubble parameter follows from their stability in the Friedmann-Robertson-Walker metric. This result is applied to models inspired by string field theory, which violate the null energy condition. Examples of stable isotropic solutions are presented. We also consider the k-essence model and analyze the stability of solutions of the form {phi}(t)=t.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Distinguishing dark matter stabilization symmetries using multiple kinematic edges and cusps

We emphasize that the stabilizing symmetry for dark matter (DM) particles does not have to be the commonly used parity (Z{sub 2}) symmetry. We therefore examine the potential of the colliders to distinguish models with parity stabilized DM from models in which the DM is stabilized by other symmetries. We often take the latter to be a Z{sub 3} symmetry for illustration. We focus on signatures where a single particle, charged under the DM stabilization symmetry decays into the DM and standard model (SM) particles. Such a Z{sub 3}-charged mother particle can decay into one or two DM particles along with the same SM particles. This can be contrasted with the decay of a Z{sub 2}-charged mother particle, where only one DM particle appears. Thus, if the intermediate particles in these decay chains are off-shell, then the reconstructed invariant mass of the SM particles exhibits two kinematic edges for the Z{sub 3} case but only one for the Z{sub 2} case. For the case of on-shell intermediate particles, distinguishing the two symmetries requires more than the kinematic edges. In this case, we note that certain decay chain topologies of the mother particle which are present for the Z{sub 3} case (but absent for the Z{sub 2} case) generate a cusp in the invariant mass distribution of the SM particles. We demonstrate that this cusp is generally invariant of the various spin configurations. We further apply these techniques within the context of explicit models.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Broken symmetry as a stabilizing remnant

The Goldberger-Wise mechanism enables one to stabilize the length of the warped extra dimension employed in Randall-Sundrum models. In this work we generalize this mechanism to models with multiple warped throats sharing a common ultraviolet brane. For independent throats this generalization is straightforward. If the throats possess a discrete interchange symmetry like Z{sub n}, the stabilizing dynamics may respect the symmetry, resulting in equal throat lengths, or they may break it. In the latter case the ground state of an initially symmetric configuration is a stabilized asymmetric configuration in which the throat lengths differ. We focus on two- (three-) throat setups with a Z{sub 2} (Z{sub 3}) interchange symmetry and present stabilization dynamics suitable for either breaking or maintaining the symmetry. Though admitting more general application, our results are relevant for existing models in the literature, including the two-throat model with Kaluza-Klein parity, and the three-throat model of flavor with a broken Z{sub 3} symmetry.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Transient Stability Study of a Real-World Microgrid with 100% Renewables

This paper performs a transient stability study of a real-world microgrid that can operate with 100% renewables to better understand the stability and reliability of the microgrid under various dynamic scenarios. In particular, the operation of multiple grid-forming (GFM) and grid-following (GFL) inverters in such a power system is not well understood under dynamic operation conditions, such as islanding and black start; therefore, in this paper, an electromagnetic transient model of the microgrid is developed to investigate the stability of the system under various dynamic operating conditions and to identify potential reliability risks. The PSCAD/EMTDC simulation with the high-fidelity model provides helpful insights into the optimal operation modes of GFM and GFL inverters as well as the stability and reliability of the microgrid. It can also inform field deployment in terms of inverter control parameters and coordination as well as the expected performance of black start and unplanned islanding.

black start↗