Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Precipitation Science”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Impact of initial temper of base metal on microstructure and mechanical properties of friction stir welded AA 7055 alloy

Highlights: • Friction stir welded 7055-T4 alloy exhibits higher tensile properties than T6 alloy. • Friction stir welded 7055-T4 alloy exhibits more uniform hardness distribution. • Some regions in heat affected zone have higher hardness than base metal in T4-joint. • Effect of initial temper on precipitate evolution in different zones is discussed. AA 7055-T6 and AA 7055-T4 aluminium alloy sheets were friction stir welded to investigate the impact of initial base metal temper on microstructure, hardness and tensile properties of the joints. In the joint of alloy in T6 temper (T6-joint), the hardness of the weld zone is lower than that of base metal; in the joint of alloy in T4 temper (T4-joint), however, some regions in the heat affected zone exhibit higher hardness than base metal. The weld nugget zone in T6-joint exhibits slightly lower hardness compared with that in T4-joint. The hardness minima is slightly higher in T4-joint than in T6-joint. T4-joint exhibits higher yield strength, ultimate tensile strength and elongation compared with T6-joint. Based on microstructure examination by transmission electron microscopy, the impact of initial precipitate state on precipitation behavior in the weld nugget zone, thermo-mechanically affected zone and heat affected zone during friction stir welding and mechanical properties of the joints is discussed.

36 MATERIALS SCIENCE↗

Projected changes in extreme rainfall and temperature events and possible implications for Cameroon's socio-economic sectors

Extreme events like flooding, droughts and heatwave are among the factors causing huge socio-economic losses to Cameroonians. Investigating the potential response of rainfall and temperature extremes to global warming is therefore critically needed for tailoring and adjusting the country's policies. Recent datasets have been developed for this purpose within the Coordinated Output for Regional Evaluations (CORDEX-CORE) initiative, at ~25 km grid spacing. These regional climate models were used to dynamically downscaled four global climate models participating in the Coupled Model Intercomparison Project phase 5 (CMIP5), under the optimistic and pessimistic representative concentration pathways (RCPs) 2.6 and 8.5, respectively. These models were employed in this study for characterizing the response of Cameroon's extreme precipitation and temperature events to global warming, using seven indices defined by the Expert Team on Cli mate Change Detection and Indices. Under global warming, the maximum number of consecutive dry (wet) days' is expected to increase (decrease). However, the annual total rainfall amount is expected to increase, mainly due to the intensification of very wet days and daily rainfall intensity. Furthermore, the temperature-based indices reveal an increase (decrease) in the total annual hot (cold) days, and overall, changes intensify with increased radiative forcing. The high-mitigated low-emission pathway RCP2.6 features attenuated changes, and even sometimes adapts to reverse the sign of changes. Designing reliable policies to limit the risks associated with the above changes is required, as their socio-economic consequences are likely to include food insecurity, heat-related illness, population impoverishment, price rises and market instability.

54 ENVIRONMENTAL SCIENCES↗

A Two-Way Shape Memory Study on Ni-Rich NiTi Shape Memory Alloy by Combination of the All-Round Treatment and the R-Phase Transformation

Ni{sub 4}Ti{sub 3} precipitates are formed in Ni-rich NiTi shape memory alloys (SMAs) after a certain heat treatment. Such a treatment then results in the changed phase transformation behavior of the alloy switching from the one-step reversible phase change B2 ↔ B19′ to the two-step, B2 ↔ R ↔ B19′, phase change. The present study reports a two-way shape memory (TWSM) due to an all-round treatment followed by an R-phase constraint aging at room temperature. The enhanced TWSM behavior was observed upon temperature cycling between 273 K (R-phase) and 77 K (B19′ phase). The effect of various constraint strains in R-phase aging by employing different diameters of the constraint ring was studied. However, the TWSM effect due to constraining the R-phase will be eliminated after a temperature rise of specimen to the fully parent phase (373 K).

36 MATERIALS SCIENCE↗

Black carbon aerosols and the third polar ice cap

Recent thinning of glaciers over the Himalayas (sometimes referred to as the third polar region) have raised concern on future water supplies since these glaciers supply water to large river systems that support millions of people inhabiting the surrounding areas. Black carbon (BC) aerosols, released from incomplete combustion, have been increasingly implicated as causing large changes in the hydrology and radiative forcing over Asia and its deposition on snow is thought to increase snow melt. In India BC emissions from biofuel combustion is highly prevalent and compared to other regions, BC aerosol amounts are high. Here, we quantify the impact of BC aerosols on snow cover and precipitation from 1990 to 2010 over the Indian subcontinental region using two different BC emission inventories. New estimates indicate that Indian BC emissions from coal and biofuel are large and transport is expected to expand rapidly in coming years. We show that over the Himalayas, from 1990 to 2000, simulated snow/ice cover decreases by {approx}0.9% due to aerosols. The contribution of the enhanced Indian BC to this decline is {approx}36%, similar to that simulated for 2000 to 2010. Spatial patterns of modeled changes in snow cover and precipitation are similar to observations (from 1990 to 2000), and are mainly obtained with the newer BC estimates.

54 ENVIRONMENTAL SCIENCES↗

Creep and microstructural processes in a low-alloy 2.25%Cr1.6%W steel (ASTM Grade 23)

A low-alloy 2.25%Cr1%Mo steel (ASTM Grade 22) has been greatly improved by the substitution of almost all of the 1%Mo by 1.6%W. The improved material has been standardized as P/T23 steel (Fe–2.25Cr–1.6W–0.25V–0.05Nb–0.07C). The present investigation was conducted on T23 steel in an effort to obtain a more complete description and understanding of the role of the microstructural evolution and deformation processes in high-temperature creep. Constant load tensile creep tests were carried out in an argon atmosphere in the temperature range 500–650 °C at stresses ranging from 50 to 400 MPa. It was found that the diffusion in the matrix lattice is the creep-rate controlling process. The results of an extensive transmission electron microscopy (TEM) analysis programme to investigate microstructure evolution as a function of temperature are described and compared with the thermodynamic calculations using the software package Thermo-Calc. The significant creep-strength drop of T23 steel after long-term creep exposures can be explained by the decrease in dislocation hardening, precipitation hardening and solid solution hardening due to the instability of the microstructure at high temperature. - Highlights: • The constant load creep tests of T23 steel were carried out at 500–650 °C. • The stress exponents of the creep rate correspond to power law (dislocation) creep. • Diffusion in the matrix lattice is the creep-rate controlling process. • The microstructure instability is the main creep degradation process in T23 steel.

36 MATERIALS SCIENCE↗

Microstructure of selective laser melted CM247LC nickel-based superalloy and its evolution through heat treatment

The selective laser melting of high temperature alloys is of great interest to the aerospace industry as it offers the prospect of producing more complex geometries than can be achieved with other manufacturing methods. In this study, the microstructure of the nickel-based superalloy, CM247LC, has been characterised following selective laser melting and after a post deposition heat treatment below the γ′ solvus temperature. In the as-deposited state, scanning electron microscopy with electron backscatter diffraction revealed a fine, cellular microstructure with preferential alignment of 〈001〉 along the build direction. A high dislocation density was seen at the periphery of the cells, indicating substantial localised deformation of the material. Fine primary MC carbides were also observed in the inter-cellular regions. High-resolution transmission electron microscopy identified the occurrence of very fine γ′ precipitates, approximately 5 nm in diameter, dispersed within the gamma phase. After heat treatment, the elongated cell colonies were observed to partially coalesce, accompanied by a decrease in dislocation density, producing columnar grains along the build direction. Cuboidal γ′ precipitates approximately 500 nm in diameter were observed to form in the recrystallised grains, accompanied by larger γ′ precipitates on the grain boundaries.

36 MATERIALS SCIENCE↗

High rate performances of the cathode material LiNi{sub 1/3}Co{sub 1/3}Mn{sub 1/3}O{sub 2} synthesized using low temperature hydroxide precipitation

Graphical abstract: A low-temperature reaction route is introduced based on hydroxide precipitation method to synthesize a cathode material LiNi{sub 1/3}Co{sub 1/3}Mn{sub 1/3}O{sub 2}. The charge-discharge tests were performed at 1000 mA g{sup -1} between 2.5 and 4.5 V and the discharge capacity is about 160 mAh g{sup -1}. The discharge capacity of the material is strongly impacted by the reaction temperature. The powders sintered at 850 {sup o}C show the best electrochemical performance. Highlights: {yields} A low-temperature reaction route is introduced based on hydroxide precipitation method to synthesize a novel cathode material LiNi{sub 1/3}Co{sub 1/3}Mn{sub 1/3}O{sub 2}. {yields} The charge-discharge tests were performed at higher current as 5 C between 2.5 and 4.5 V. {yields} The discharge capacity of the material is strongly impacted by the reaction temperature. The powders sintered at 850 {sup o}C show the best electrochemical performance. -- Abstract: A low-temperature reaction route is introduced based on hydroxide precipitation method to synthesize the cathode material LiNi{sub 1/3}Co{sub 1/3}Mn{sub 1/3}O{sub 2}. The crystal structure and morphology of the prepared powder have been characterized by X-ray diffraction and Scan electron microscope, respectively. The charge-discharge tests were performed between 2.5 and 4.5 V. The discharge capacity of the material is strongly impacted by the reaction temperature. The powders sintered at 850 {sup o}C show the best electrochemical performance and the initial discharge capacity is about 160 mAh g{sup -1} at 5 C. Powder X-ray diffraction and Scan electron microscope results reveal that the excellent electrochemical performances should be ascribed to the lower precursor reaction temperature, the lower degree of cation mixing and analogous spherical small particles, which can improve the transfer of Li ions and electrons. All these results indicate that this material has potential application in lithium-ion batteries.

36 MATERIALS SCIENCE↗

Understanding the microstructural stability in a y’-strengthened Ni-Fe-Cr-Al-Ti alloy

Ni-Fe-Cr-Al-Ti alloys, with Ni levels near 50 wt.%, have the potential to develop a microstructure consisting of a face-centered cubic ? matrix with the homogeneous precipitation of fine ordered ?’ precipitates similar to traditional Ni-based superalloys with significantly greater Ni content. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), atom probe tomography (APT), and CALPHAD -based thermodynamic modeling were employed to understand the phase stabilities and microstructural evolution in an age-hardenable Ni-27Fe-18Cr-1Co-1.6Al-3.75Ti-1.2Mo-0.03C (wt%) alloy. The primary heat-treatment of solution annealing at 1121°C for 4h and age-hardening treatment at 760 °C for 16h resulted in a microstructure consisting of fine ?’ precipitates in an austenitic matrix along with grain boundary carbides, consistent with thermodynamic calculations. Long-term aging at 900 °C for 250h resulted in the coarsening of ?’ along with a change in the morphology of the precipitates from spherical to a more cuboidal shape. In addition, ? phase formation was observed concomitant with the partial dissolution of the ?’ phase. The ability of computational thermodynamic models to predict microstructural characteristics is discussed.

Gwalani, Bharat↗

Speciation and Distribution of Phosphorus in a Fertilized Soil: A Synchrotron-Based Investigation

Phosphorus availability is often a limiting factor for crop production around the world. The efficiency of P fertilizers in calcareous soils is limited by reactions that decrease P availability; however, fluid fertilizers have recently been shown, in highly calcareous soils of southern Australia, to be more efficient for crop (wheat [Triticum aestivum L.]) P nutrition than granular products. To elucidate the mechanisms responsible for this differential response, an isotopic dilution technique (E value) coupled with a synchrotron-based spectroscopic investigation were used to assess the reaction products of a granular (monoammonium phosphate, MAP) and a fluid P (technical-grade monoammonium phosphate, TG-MAP) fertilizer in a highly calcareous soil. The isotopic exchangeability of P from the fluid fertilizer, measured with the E-value technique, was higher than that of the granular product. The spatially resolved spectroscopic investigation, performed using nano x-ray fluorescence and nano x-ray absorption near-edge structure (n-XANES), showed that P is heterogeneously distributed in soil and that, at least in this highly calcareous soil, it is invariably associated with Ca rather than Fe at the nanoscale. 'Bulk' XANES spectroscopy revealed that, in the soil surrounding fertilizer granules, P precipitation in the form of octacalcium phosphate and apatite-like compounds is the dominant mechanism responsible for decreases in P exchangeability. This process was less prominent when the fluid P fertilizer was applied to the soil.

54 ENVIRONMENTAL SCIENCES↗

Creep-rupture performance of 0.07C-23Cr-45Ni-6W-Ti,Nb austenitic alloy (HR6W) tubes

A series of base metal and cross-weld creep-rupture tests were conducted on the advanced austenitic alloy, HR6W, to evaluate the material for use at advanced ultrasupercritical (A-USC) steam conditions. Creep deformation and rupture were evaluated by traditional methods and data were compared with other studies to evaluate the creep response of the material. Optical and scanning electron microscopy revealed changes in failure mode and precipitation behavior. Thermodynamic predictions of phase stability were conducted and the results were compared with the experimental data. This research confirmed the important role of W and the precipitation of laves phase in the alloy system, but a direct relationship between laves phase content and creep strength was not observed. Furthermore, Cr content was investigated as an additional factor which may be important in the microstructural stability of the alloy which had not been previously considered. Finally, when compared to commercially available stainless steels, this heat of HR6W showed no creep strength advantage for A-USC application.

36 MATERIALS SCIENCE↗

Interactive microstructural phenomena during non-isothermal annealing of an Al-Mg-Si-Cu alloy

Highlights: • A non-isothermal annealing process that is concurrent with precipitation is investigated. • The mechanism of grain refinement through the interactions of precipitation, recovery and recrystallization is identified. • The combination of non-isothermal annealing and proper pre-deformation temper condition tetrads recovery. • Massive recrystallization nucleation is achieved by delaying recovery. • The growth of recrystallized grains is controlled by coarsening of precipitates that pin the grain boundaries. - Abstract: Interactions between precipitation, recovery and recrystallization during a non-isothermal annealing process in an Al-Mg-Si-Cu alloy have been investigated through a comprehensive experimental analysis. Non-isothermal annealing with a slow heating rate that starts from a low temperature is found to promote homogeneous nucleation of precipitates. The uniformly distributed precipitates limit the extent of recovery, which in turn facilitates extensive nucleation of new grains within the deformed microstructure. The growth of the recrystallized grains is strongly controlled through pinning of grain boundaries by precipitates. During the final stages of annealing, enhanced diffusion at the recrystallization front leads to preferential precipitate coarsening, release of grain boundaries from precipitates pinning, and completion of recrystallization. These interactive microstructural phenomena explain the effectiveness of a non-isothermal annealing route combined with an adequate level of deformation in obtaining a fine-grained recrystallized structure.

36 MATERIALS SCIENCE↗

Contribution of Eu ions on the precipitation of silver nanoparticles in Ag-Eu co-doped borate glasses

Graphical abstract: - Highlights: • Silver nanoparticles are precipitated from the borate glasses during the melting process without any further heat treatment. • The reduction of Eu{sup 3+} ions to Eu{sup 2+} ions is presented in this material. • The intensity of Ag{sup +} luminescence. • The introduction of Eu ions accelerated the reaction between Eu{sup 2+} ions and silver ions inducing the silver clusters formation. - Abstract: Ag{sup +} doped sodium borate glasses with different Eu ions concentration were prepared by the melt-quenching method. The absorption at about 410 nm which was caused by the surface plasmon resonance (SPR) of Ag nanoparticles (NPs) is promoted with increasing of Eu ions concentration. Meanwhile, the luminescent spectra showed that the emission intensity of Ag{sup +} decreased while that of the Ag aggregates increased simultaneously. The results indicated that the Ag ions intend to form the high-polymeric state such as Ag aggregates and nanoparticles with increasing of europium ions. Owing to the self-reduction of Eu{sup 3+} to Eu{sup 2+} in our glass system, it revealed that Ag{sup +} has been reduced by the neighboring Eu{sup 2+} which leads to the formation of Ag aggregates and the precipitation of Ag NPs in the matrix. In addition, energy transfer (ET) process from Ag{sup +}/Ag aggregates to the Eu{sup 3+} was investigated for the enhancement of Eu{sup 3+} luminescence.

36 MATERIALS SCIENCE↗

Effects of heat input on microstructure and tensile properties of laser welded magnesium alloy AZ31

A 3 kW CO{sub 2} laser beam was used to join wrought magnesium alloy AZ31 sheets, and the effects of heat input on the quality of butt welding joints were studied. By macro and microanalysis, it is found that the welding heat input plays an important role in laser welding process for AZ31 wrought sheets. After welding, the grains far from the weld centre present the typical rolled structure. But the microstructure out of the fusion zone gradually changes to complete equiaxed crystals as the distance from the weld centre decreases. Adjacent to the fusion boundary, there is a band region with columnar grains, and its growth direction is obviously perpendicular to the solid/liquid line. The microstructure in fusion centre consists of fine equiaxed grains and the many precipitated particles are brittle phase Mg{sub 17}Al{sub 12} or Mg{sub 17}(Al,Zn){sub 12}. With increasing the heat input, the band width of columnar grains varies, the grains in fusion zone get coarser, and the distribution of precipitates changes from intragranularly scattered particles to intergranularly packed ones. The results of tensile test show that the change trend of ultimate tensile strength (UTS) and elongation of the welded joints is to increase at first and then decrease with the heat input increasing. When the heat input reaches 24 J mm{sup -1}, the maximum value of the UTS is up to 96.8% of the base metal.

36 MATERIALS SCIENCE↗

Crystal development during carbonation of lime-based mortars in different environmental conditions

Highlights: • High CO{sub 2} and DiloCarb® treatment favour advanced carbonation and self-healing. • In the lime mortar without ceramics, channel type pores occur in the aggregate border. • In the lime mortars with ceramics, vug type pores are produced in the binder during kneading. • The formation of tabular CaCO{sub 3} polymorphs caused an increase in stress leading to microshrinkage cracks. • The use of a ceramic provoked dissolution and then re-precipitation of more stable polymorphs. - Abstract: This study examines crystal development during the carbonation of lime mortars according to the additives used and curing conditions. Two types of samples were prepared, one with sand and the other one additionally including Roman ceramics. These mortars were cured: 1) by spraying with a carbonation accelerator product under laboratory conditions; 2) in a climate chamber under 20 °C, 60% relative humidity, and 1600 ppm CO{sub 2}; and 3) under laboratory conditions as controls. Polarized light microscopy, SEM-EDS and XRD were used at 28, 90, 120 and 180 days to monitor the carbonation process. Observations indicate the development of different CaCO{sub 3} polymorphs, which appeared as metastable phases. The early nucleation of a well-defined calcite phase as the most stable CaCO{sub 3} polymorph was only identified in the chamber-cured samples. Differences in the pore network were observed depending on the composition and morphology of the mortar components and the environmental curing conditions.

36 MATERIALS SCIENCE↗

Metrics for the Diurnal Cycle of Precipitation: Toward Routine Benchmarks for Climate Models

In this paper, metrics are proposed—that is, a few summary statistics that condense large amounts of data from observations or model simulations—encapsulating the diurnal cycle of precipitation. Vector area averaging of Fourier amplitude and phase produces useful information in a reasonably small number of harmonic dial plots, a procedure familiar from atmospheric tide research. The metrics cover most of the globe but down-weight high-latitude wintertime ocean areas where baroclinic waves are most prominent. This enables intercomparison of a large number of climate models with observations and with each other. The diurnal cycle of precipitation has features not encountered in typical climate model intercomparisons, notably the absence of meaningful “average model” results that can be displayed in a single two-dimensional map. Displaying one map per model guides development of the metrics proposed here by making it clear that land and ocean areas must be averaged separately, but interpreting maps from all models becomes problematic as the size of a multimodel ensemble increases. Global diurnal metrics provide quick comparisons with observations and among models, using the most recent version of the Coupled Model Intercomparison Project (CMIP). This includes, for the first time in CMIP, spatial resolutions comparable to global satellite observations. Finally, consistent with earlier studies of resolution versus parameterization of the diurnal cycle, the longstanding tendency of models to produce rainfall too early in the day persists in the high-resolution simulations, as expected if the error is due to subgrid-scale physics.

54 ENVIRONMENTAL SCIENCES↗

Regional climate change of the greater Zambezi River Basin: a hybrid assessment

Projections of regional changes in surface-air temperature and precipitation, in response to unconstrained emissions as well as a climate mitigation policy, for the Zambezi River Basin (ZRB) are presented. These projections are cast in a probabilistic context through a hybrid technique that combines the projections of the MIT Integrated Global System Model (IGSM) to pattern-change kernels from climate-model results of the Coupled Model Intercomparison Project (CMIP). Distributional changes of precipitation and surface-air temperature averaged over the western and eastern ZRB are considered. In general, the most significant response to climate policy is seen in the spring. Frequency distributions of precipitation change for the unconstrained emission scenario indicate a majority of the outcomes to be drier by 2050, although the distribution spans both increased and decreased precipitation. Through climate policy, the distributions’ total range of outcomes collapses considerably, and perhaps more importantly, the mode of the distribution aligns with zero precipitation change. For surface-air temperature, climate policy consistently reduces the modal value of warming, and this reduction is robust for the western ZRB. Climate policy also considerably abates the occurrence of the most extreme temperature increases, but the minimum warming in the distributions is less affected.

54 ENVIRONMENTAL SCIENCES↗

Uranium Plume Treatability Demonstration at the Hanford Site 300 Area: Development of Polyphosphate Remediation Technology for In-Situ Stabilization of Uranium - 8070

A groundwater plume containing uranium, originating from a combination of purposeful discharges of wastewater to cribs, trenches and ponds, along with some accidental leaks and spills during nuclear fuel fabrication activities, has persisted beneath the Hanford Site 300 Area for many years. Despite the cessation of uranium releases and the removal of shallow vadose zone source materials, the goal of less than 30 µg/L has not been achieved within the anticipated 10-year time period. Polyphosphate technology has been demonstrated to delay the precipitation of phosphate phases for controlled in situ precipitation of stable phosphate phases to control the long-term fate of uranium. Precipitation occurs when polyphosphate compounds hydrolyze to yield the orthophosphate molecule. Based on the hydrolysis kinetics of the polyphosphate polymer, the amendment can be tailored to act as a time-released source of phosphate for lateral plume treatment, immediate and sustained remediation of dissolved uranium, and to preclude rapid precipitation which could result in a drastic change in hydraulic conductivity of the target aquifer. Critical to successful implementation of polyphosphate remediation technology is a site specific evaluation and optimization of multi-length polyphosphate amendment formulations. A multi-faceted approach has been taken to provide key fundamental science knowledge regarding optimization of the polyphosphate remedy through: 1) phosphorus-31 nuclear magnetic resonance to quantify the effects of Hanford groundwater and sediment on the degradation of inorganic phosphates, 2) static tests to quantify the kinetics, loading, and stability of apatite as a long-term sorbent for uranium, and 3) single-pass flow through testing to quantify the stability of autunite and apatite under relevant site conditions. Dynamic column tests were utilized to 1) optimize the composition of the polyphosphate formulation for the formation and emplacement of apatite and autunite, 2) understand the rate and extent of reaction between polyphosphate and uranium-bearing phases, 3) evaluate the effect of chemical microenvironments on the degradation of polyphosphate and the formation of autunite, and 4) quantify the mobility of polyphosphate as a function of water content. These activities are being conducted in parallel with a limited field investigation, to more accurately define the vertical extent of uranium in the vadose zone, and in the capillary fringe laterally throughout the plume.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Characteristic constitution model and microstructure of an Al-3.5Cu-1.5Li alloy subjected to thermal deformation

The constitution model and microstructure of 2A97 Al-Li alloy during thermal deformation were investigated. The thermal deformation behavior was dominated by the interaction between work hardening and dynamic softening. The constitution model was constructed to predict the rheology behavior, in which Zener-Holloman equation with a fifth-order polynomial was set to describe the effect of various strains on the material parameters. Processing maps displayed to exist two unstable domains in microstructure (one domain with the temperature range from 300 °C to 370 °C and the strain rate range from 10{sup 0.5} s{sup −1} to 10s{sup −1}, and the other with the temperature range from 380 °C to 500 °C and the strain rate range from 0 s{sup −1} to 10 s{sup −1}). Microstructural characteristics of dynamic recovery (DRV) and dynamic recrystallization (DRX) in the stable domain and local rheology in the unstable domain were observed, respectively. The dynamic precipitation (DPN) of T{sub 1} phases and the interaction between dislocations and Al{sub 20}Cu{sub 2}Mn{sub 3} and Al{sub 3}Zr phases were concluded by high resolution transmission electron microscopy (HRTEM), which was the first experimental evidence for the DPN in 2A97 Al-Li alloy. All these confirmed the occurrence of the continuous dynamic recrystallization during thermal deformation.

36 MATERIALS SCIENCE↗