Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRESSING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Thin film ceria–bismuth bilayer electrolytes for intermediate temperature solid oxide fuel cells with La0.85Sr0.15MnO3-δ–Y0.25Bi0.75O1.5 cathodes

Thin film electrolytes of bilayer bismuth oxide/ceria are developed for intermediate temperature solid oxide fuel cells. Y0.25Bi0.75O1.5 is deposited via Direct Current magnetron sputtering technique on an Sm0.2Ce0.8O1.90 electrolyte film which is prepared by a dry-pressing process on an NiO–Sm0.2Ce0.8O1.90 substrate. La0.85Sr0.15MnO3-δ–Y0.25Bi0.75O1.5 composite is applied onto the Y0.25Bi0.75O1.5 film as the cathode to form a single cell. Cells with 6-μm-thick Y0.25Bi0.75O1.5 and 26-μm-thick Sm0.2Ce0.8O1.90 bilayer electrolytes exhibit improved open circuit voltages and power density compared with those obtained with only Sm0.2Ce0.8O1.90 electrolytes. The open circuit voltages are comparable and power densities are higher than those previously reported for solid oxide fuel cells with thick bilayer electrolytes using noble metals such as Pt as the electrodes. Impedance spectra show that the change of electrolyte resistance is negligible while the cathodic interfacial polarization resistance decreased significantly when the Y0.25Bi0.75O1.5 layer is added to form the Sm0.2Ce0.8O1.90/Y0.25Bi0.75O1.5 bilayer electrolytes.

36 MATERIALS SCIENCE↗

Microstructure control on thermoelectric properties of Ca{sub 0.96}Sm{sub 0.04}MnO{sub 3} synthesised by co-precipitation technique

Nanopowder of Ca{sub 0.96}Sm{sub 0.04}MnO{sub 3} (CSM) perovskite was prepared by chemical co-precipitation technique. It was characterized and studied by X-ray diffraction and Transmission Electron Microscopy. Nano-crystalline CSM phase having grain size of 60-70 nm can be prepared by calcination at 1073 K for 6 h in air. The obtained nanopowder was pressed, sintered at 1373 K for 24 h to obtain a dense sample. In comparison, CSM samples prepared from normal powder need sintering temperature of 1623 K to reach a similar microstructure, showing the efficiency of nanopowder to decrease the sintering temperature. The thermoelectric properties of samples prepared with two different processes were studied. The Seebeck coefficient and the thermal conductivity slightly decrease by using the nanopowder while the value of the electrical resistivity does not change. This results in the same figures of merit for the two materials.

36 MATERIALS SCIENCE↗

Multiferroic properties of Pb{sub 2}Fe{sub 2}O{sub 5} ceramics

Research highlights: {yields} Simultaneous occurrence of ferromagnetism and ferroelectricity in Pb{sub 2}Fe{sub 2}O{sub 5} ceramics. {yields} The off-centers of shifted Pb{sup 2+} ions as well as the FeO{sub 6} octahedra in the 'Pb{sub 2}Fe{sub 2}O{sub 5}' lead to a ferroelectric polarization. {yields} Pb{sub 2}Fe{sub 2}O{sub 5} ceramic demonstrates ferromagnetic order state due to the spin arrangement in the double chains of FeO{sub 5} tetrahedral pyramids. -- Abstract: Pb{sub 2}Fe{sub 2}O{sub 5} (PFO) powders in monoclinic structure have been synthesized using lead acetate in glycerin and ferric acetylacetonate as the precursor. The powders were pressed into pellets, which were sintered into ceramics at 800 {sup o}C for 1 h. The morphology and structure have been determined by X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM). Polarization was observed in Pb{sub 2}Fe{sub 2}O{sub 5} ceramics at room temperature, exhibiting a clear ferroelectric hysteresis loop. The remanent polarization of Pb{sub 2}Fe{sub 2}O{sub 5} ceramic is estimated to be Pr {approx} 0.22 {mu}C/cm{sup 2}. The origin of the polarization may be attributed to the off-centers of shifted Pb{sup 2+} ions as well as the FeO{sub 6} octahedra in the perovskite-based structure of Pb{sub 2}Fe{sub 2}O{sub 5}. Magnetic hysteresis loop was also observed at room temperature. The Pb{sub 2}Fe{sub 2}O{sub 5} ceramic shows coexistence of ferroelectricity and ferromagnetism. It provides a new field of research for complex oxides with multiferroic properties.

36 MATERIALS SCIENCE↗

Microstructural and electrical changes in nickel manganite powder induced by mechanical activation

Highlights: {yields} The influence of mechanical activation on microstructure evolution in the nickel manganite powder was investigated as well as electrical properties of the sintered samples. {yields} Structural refinement obtained by Topas-Academic software based on Rietveld analysis showed that the milling process remarkably changed the powder morphology and microstructure. {yields} SEM studies of sintered samples also revealed the strong influence of milling time on ceramics density (increases with milling time). {yields} The electrical properties of ceramic samples are clearly conditioned by terms of synthesis, in our case the time of mechanical activation. {yields} The highest density and higher values of dielectric constant were achieved at the sample activated for 45 min. -- Abstract: Nickel manganite powder synthesized by calcination of a stoichiometric mixture of manganese and nickel oxide was additionally mechanically activated in a high energy planetary ball mill for 5-60 min in order to obtain a pure NiMn{sub 2}O{sub 4} phase. The as-prepared powders were uniaxially pressed into disc shape pellets and then sintered for 60 min at 1200 {sup o}C. Changes in the particle morphology induced by mechanical activation were monitored using scanning electron microscopy, while changes in powder structural characteristics were followed using X-ray powder diffraction. The ac impedance spectroscopy was performed on sintered nickel manganite samples at 25 {sup o}C, 50 {sup o}C and 80 {sup o}C. It was shown that mechanical activation intensifies transport processes causing a decrease in the average crystallites size, while longer activation times can lead to the formation of aggregates, defects and increase of lattice microstrains. The observed changes in microstructures were correlated with measured electrical properties in order to define optimal processing conditions.

36 MATERIALS SCIENCE↗

In situ formation of sintered cordierite–mullite nano–micro composites by utilizing of waste silica fume

Highlights: ► We succeeded to obtain in situ formed sintered cordierite–mullite nano–macro composites from waste and pure materials at 1400 °C. ► Their sinterability was greatly dependent on both firing temperature and composition. ► XRD patterns showed that the optimum temperature required for formation of sintered cordierite–mullite nano–macro composites was achieved at 1400 °C. ► The batch containing 70 wt.% cordierite and 30 wt.% mullite exhibited the best properties. ► Microstructures of the densified composites were composed of nano–macro cordierite–mullite structures. -- Abstract: This study aims at in situ formation of sintered cordierite–mullite nano–macro composites having high technological properties using waste silica fume, calcined ball clay, calcined alumina, and magnesia as starting materials. The starting materials were mixed in different ratios to obtain different cordierite–mullite composite batches in which the cordierite contents ranged from 50 to 100 wt.%. The batches were uni-axially pressed at 100 MPa and sintered at 1350, 1400 and 1450 °C to select the optimum temperature required for cordierite–mullite nano–macro composites formation. The formed phases were identified by X-ray diffraction (XRD) pattern. The sintering parameters in terms of bulk density (BD) and apparent porosity (AP) were determined. The microstructure of composites has been investigated by scanning electron microscope (SEM). Cold crushing strength (CCS) of the sintered batches was evaluated. The result revealed that the cordierite–mullite nano–macro composites were in-situ formed at 1400 °C. The batch containing 70 wt.% cordierite showed good physical and mechanical properties.

36 MATERIALS SCIENCE↗

Photo-oxidative degradation of TiO{sub 2}/polypropylene films

Graphical abstract: - Highlights: • Photo-oxidative degradation of polypropylene is accelerated by TiO{sub 2} incorporation. • Weight loss, FTIR, SEM and GPC shown high degree of degradation of polypropylene. • A mechanism of the photo-degradation of polypropylene by TiO{sub 2} is proposed. - Abstract: Photo-oxidative degradation of polypropylene films with TiO{sub 2} nanoparticles incorporated was studied in a chamber of weathering with Xenon lamps as irradiation source. TiO{sub 2} powder with crystalline structure of anatase was synthesized by thermal treatments at 400 and 500 °C starting from a precursor material obtained by sol–gel method. Composites of TiO{sub 2}/polypropylene were prepared with 0.1, 0.5 and 1.0 wt% of TiO{sub 2}. The mixture of components was performed using a twin screw extruder, the resulting material was pelletized by mechanical fragmenting and then hot-pressed in order to form polypropylene films with TiO{sub 2} dispersed homogeneously. Photo-oxidative degradation process was followed by visual inspection, weight loss of films, scanning electron microscopy (SEM), infrared spectroscopy with Fourier transformed (FTIR), and gel permeation chromatography (GPC)

36 MATERIALS SCIENCE↗

Magnetic force microscopy study of domain walls in Co{sub 2}Z ferrite

Graphical abstract: - Highlights: • Hexaferrite Co{sub 2}Z is synthesized through the modified Pechini method. • Magnetic domains are observed in anisotropic Co{sub 2}Z single grain using MFM. • Observed single grain domain thickness is in good agreement with Dotsh model. - Abstract: Hexaferrite Co{sub 2}Z was synthesized through the modified Pechini method. Partially oriented samples were obtained after consolidation with uniaxial pressing and calcination/sintering at 1300 °C/1330 °C. The sample composition and morphology was identified with X-ray diffractometry (XRD) and scanning electron microscopy (SEM) with energy-dispersive X-ray spectrometry (EDS). MFM studies of the single grains revealed a domain structure with 0.7 μm wide. The Co{sub 2}Z static magnetization was measured with a vibrating sample magnetometer (VSM), and was used to calculate a single grain domain with a thickness of 4.8 μm. This result is in good agreement with SEM observations of the single grain thickness.

36 MATERIALS SCIENCE↗

Structural, morphological and dielectric properties of BiNbO{sub 4} ceramics prepared by the sol-gel method

Highlights: • The thermal treatment at 1200 °C generates a non-stoichiometric secondary phase. • The secondary phase Bi{sub 3.54}Nb{sub 7.09}O{sub 22.7}, is responsible for the highest Q × f and density. • The samples with triclinic BiNbO{sub 4} have the highest ε′. - Abstract: BiNbO{sub 4} ceramic powders were prepared using the sol-gel method. The fine particles were pressed into cylinders and, then, they were treated at temperatures between 500 and 1150 °C. The structure was studied by X-ray diffraction and Raman spectroscopy and the morphology was observed by scanning electron microscopy. The measurements of the complex permittivity were made in a resonant cavity operating at 2.7 GHz, using the small perturbation method. The reversible phase transformation between β-BiNbO{sub 4} and α-BiNbO{sub 4} was observed. The density, dielectric constant (ε') and the dielectric loss (tg δ) of the prepared powders increase with the sintering temperature, and the sample treated at 1150 °C shows the highest ε' and the highest Q × f.

36 MATERIALS SCIENCE↗

Conductive nanolamellar Cu/martensite wire with high strength

Cu wires can be greatly strengthened without losing much conductivity if a continuous nanolamellar structure with Cu and a strong second constituent is achieved. Here, we report on a nanolamellar Cu/steel wire fabricated by repetitive hot-pressing, forging, rolling and subsequent wire drawing. Austenization and quenching in liquid nitrogen resulted in a Cu/martensite structure, exhibiting tensile strength of 1220 MPa. The electrical conductivity of the wire was measured to be about 60% International Annealed Copper Standard (IACS), which was comparable with Cu/Fe fabricated by alloying and casting. In situ tensile tests under high energy X-ray diffraction were utilized to explore the deformation behavior of the wire. It was discovered that the martensite carried about 60% of the load, accounting for the high strength.

36 MATERIALS SCIENCE↗

Electrophoretic deposition for improved trace element homogeneity in silica reference materials

Spatially-resolved analysis requires homogeneous reference materials (RMs) to make reliable quantitative measurements. Here we previously developed an electrophoretic deposition (EPD) method for fabrication of glassy microanalytical RMs with superior platinum-group element homogeneity **[1], and now include further dopants. For 39 trace elements, we analyzed dopant homogeneity in sintered silica (SiO 2 ) samples consolidated either mechanically by die-pressing (DP) or by EPD. A set of EPD and DP samples was made from each of two nanoparticle feedstocks produced by variations of the Stöber process **[2]. Spatially-resolved dopant distribution was characterized in all samples by laser-ablation inductively-coupled plasma mass spectrometry (LA-ICP-MS). In both sample sets, homogeneity of most trace elements was substantially improved by EPD relative to their DP counterpart.

36 MATERIALS SCIENCE↗

Electrospun Nafion/PVDF single-fiber blended membranes for regenerative H 2 /Br 2 fuel cells

Nafion® perfluorosulfonic acid (PFSA) and poly(vinylidene fluoride) (PVDF) were electrospun simultaneously as a polymer solution mixture using a single needle spinneret. The nanofiber morphology was highly unusual, with bundled 2–5 nm fibril strands of Nafion and PVDF aligned along the fiber axis. Membranes were made from fiber mats by a simple hot-pressing step, followed by thermal annealing, where the fibril morphology of Nafion and PVDF in the original nanofibers was retained in the membrane. The PVDF component in the final membrane served three roles, as an electrospinning carrier polymer for PFSA, a mechanical reinforcement, and a hydrophobic (uncharged) component to limit PFSA ionomer swelling. A series of single-fiber membranes with Nafion/PVDF contents ranging from 40/60 to 90/10 wt%/wt% were prepared, characterized, and evaluated for use in a regenerative hydrogen/bromine fuel cell. As anticipated, there was a decrease in proton conductivity, water/electrolyte swelling, and Br 2 /Br 3 - permeability with increasing PVDF content. Membrane conductivity was lower than expected based on the weight fraction of PVDF, due presumably to an unusually large fraction of highly structured water. Nevertheless, a single-fiber Nafion/PVDF membrane with a thickness of 18 µm and an 80/20 wt%/wt% Nafion/PVDF composition performed well in a H 2 /Br 2 regenerative fuel cell due to a combination of low area-specific resistance and low Br 2 /Br 3 - crossover. Thus, with an electrolyte containing 0.9 M Br 2 in 1.0 M HBr, the maximum power output was 46% higher than that with a Nafion 212 membrane (1.31 vs. 0.90 W/cm 2 ).

42 ENGINEERING↗

High-pressure CO 2 permeation properties and stability of ceramic-carbonate dual-phase membranes

CO 2 permeation properties and stability of ceramic-carbonate dual-phase membranes at high pressures/temperatures are critical to their CO 2 separation and membrane reactor applications, but such data are not available in the literature. Here, this work aims to study the effect of high transmembrane pressure on CO 2 permeation flux and the stability of molten carbonate in the dual-phase samarium-doped ceria (SDC) and molten-carbonate (MC) membranes. Dead-end porous SDC tubular supports were made by a cold isostatic press (CIP)/sintering method with a low porosity (below 7%), and gas-tight SDC-MC membranes were prepared by direct infiltration of molten lithium and sodium carbonate mixture into SDC pores, with a MC volume fraction less than 7%. CO 2 permeation/separation tests were performed on the SDC-MC membranes using feed gas of equal molar CO 2 /N 2 mixture at feed pressures up to 15 atm and sweep gas of helium at 1 atm. CO 2 permeation flux for the SDC-MC membranes depends logarithmically on feed/permeate CO 2 pressure ratio in 660–810°C. The temperature dependence of CO 2 permeation shows activation energy of 30 kJ/mol. Due to the small MC volume fraction and hence low effective carbonate conductivity, CO 2 permeation of the SDC-MC membranes is dominated by the carbonate ionic conduction in the MC phase. The SDC-MC membranes remain in the same structure, morphology, and gas-tightness after CO 2 separation tests at high feed pressures and temperatures, showing high stability of SDC-MC membranes for high-temperature, high-pressure separation and chemical reaction applications.

36 MATERIALS SCIENCE↗

Investigation of competitive sorption and plasticization of hyperaged CANAL ladder polymers for acid gas purification

Identifying membrane materials that have exceptional separation performance and stability to complex CO 2 -containing mixtures is a pressing topic in separation science. In this work, the membrane separation performance for a recently discovered class of contorted polymers synthesized via catalytic arene-norbornene annulation (CANAL) polymerization is presented. These CANAL polymers achieve high CO 2 /CH 4 selectivity of 68 after physical aging (up to ∼1 year), which significantly augments the size-sieving capabilities of the membranes. Binary CO 2 /CH 4 and ternary H 2 S/CO 2 /CH 4 testing result in a 41 % and 50 % enhancement in selectivities, respectively, for hyperaged (∼1 year) contorted CANAL polymers, highlighting their size-sieving capabilities. The remarkably high CO 2 /CH 4 mixed-gas and combined acid gas (CAG, (CO 2 +H 2 S)/CH 4 ) selectivities of 88 and 95, respectively, for CANAL-Me-S 5 F in particular surpass both the 2018 CO 2 /CH 4 mixed-gas and CAG upper bounds. Performance stability was also investigated for high concentrations of CO 2 , revealing a reduction in CO 2 /CH 4 mixed-gas selectivity without compromising CO 2 permeability, suggesting strong sorption of CO 2 but minimal plasticization effects for short testing periods. In addition, time-dependent plasticization shows negligible effects on CO 2 /CH 4 mixed-gas selectivity despite an increase in CO 2 permeability when exposed to high concentrations of plasticizing CO 2 over an extended period of 170 h. This study provides valuable insights into hyperaged CANAL polymers and their performance in practical industrial processes.

03 NATURAL GAS↗

Thermal equation of state of a natural kyanite up to 8.55 GPa and 1273 K

The thermal equation of state of a natural kyanite has been investigated with a DIA-type, cubic-anvil apparatus (SAM85) combined with an energy-dispersive synchrotron X-ray radiation technique up to 8.55 GPa and 1273 K. No phase transition was observed in the studied pressure-temperature (P-T) range. The Le Bail full profile refinement technique was used to derive the unit-cell parameters. By fixing the bulk modulus K0 as 196 GPa and its pressure derivative K0′ as 4, our P-V (volume)-T data were fitted to the high temperature Birch–Murnaghan equation of state. The obtained parameters for the kyanite are: V0 = 294.05(9) Å3, α = 2.53(11) × 10−5 K−1 and (∂K/∂T)P = −0.021(8) GPa∙K−1. These parameters have been combined with other experimentally-measured thermodynamic data for the relevant phases to calculate the P-T locus of the reaction kyanite = stishovite + corundum. With this thermodynamically constrained phase boundary, previous high-pressure phase equilibrium experimental studies with the multi-anvil press have been evaluated.

He, Qiang↗

Microstructure and mechanical behavior of neutron irradiated ultrafine grained ferritic steel

Neutron irradiation effects on ultra-fine grain (UFG) low carbon steel prepared by equal channel angular pressing (ECAP) has been examined. Counterpart samples with conventional grain (CG) sizes have been irradiated alongside with the UFG ones for comparison. Samples were irradiated in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) to 1.24 dpa. Atom probe tomography revealed manganese, silicon-enriched clusters in both ECAP and CG steel after neutron irradiation. X-ray quantitative analysis showed that dislocation density in CG increased after irradiation. However, no significant change was observed in UFG steel revealing better radiation tolerance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Tensile properties of a novel W-NiTi heavy alloy with transforming matrix

A new class of W-NiTi heavy alloy was prepared by infiltration and vacuum hot pressing. The W-NiTi heavy alloy containing 90 wt% tungsten of particle size 2-8 gm exhibited excellent tensile properties of the tensile strength (1120 MPa) and elongation (7.8%). In situ synchrotron diffraction experiments provided clear evidence on the reorientation of B19'-NiTi martensite at the initial stage of the deformation and the martensitic transformation from B2-NiTi to B19'-NiTi martensite. Finally, the strain hardening of the heavy alloy resulted from the deformation of the martensite phase and the strain hardening of tungsten particles.

36 MATERIALS SCIENCE↗

Implications of post-processing induced microstructural changes on the deformation and fracture response of additively manufactured Ti–6Al–4V

Ti–6Al–4V parts fabricated via electron beam melting (EBM) powder bed fusion are often subjected to hot isostatic pressing below the β-transus temperature to mitigate defects. During which the pressure aids in pore closure and the thermal exposure results in coarsening of α phase while retaining the columnar prior-β phase grain morphology present in the as-fabricated condition. The same post-processing treatment can also be carried out above β-transus temperature which is an effective way to modify both the grain morphology and the associated α textures. Here, the objective of this work is to correlate thermally induced microstructural changes to the deformation and fracture response of the EBM processed Ti–6Al–4V. To this end, we have carried out both sub-transus and super-transus heat-treatments of the as-fabricated material. The mechanical response of the as-fabricated and all heat-treated materials are characterized by in-situ tensile tests under a high-resolution digital optical microscope. This enabled us to capture large-scale panoramic images of the deforming microstructure, and overcome the trade-off between the image resolution and the field of view during in-situ experiments. The series of images captured throughout the imposed deformation are subsequently used to perform microstructure-based digital image correlation to measure microstructural-scale strains over a large area. The results of the in-situ tests together with detailed fractographic analyses are then used to elucidate how the heterogeneous deformation spanning over multiple microstructural length-scales, for example, at the scale of lamellae, colonies of lamellae and grain boundaries, affect the overall deformation and fracture response of the post-processed materials.

36 MATERIALS SCIENCE↗

Comparing structure-property evolution for PM-HIP and forged alloy 625 irradiated with neutrons to 1 dpa

The nuclear power industry has growing interest in qualifying powder metallurgy with hot isostatic pressing (PM-HIP) to replace traditional alloy fabrication methods for reactor structural components. But there is little known about the response of PM-HIP alloys to reactor conditions. This study directly compares the response of PM-HIP to forged Ni-base Alloy 625 under neutron irradiation doses ~0.5–1 displacements per atom (dpa) at temperatures ranging ~321–385 °C. Post-irradiation examination involves microstructure characterization, ASTM E8 uniaxial tensile testing, and fractography. Up through 1 dpa, PM-HIP Alloy 625 appears more resistant to irradiation-induced cavity nucleation than its forged counterpart, and consequently experiences significantly less hardening. This observed difference in performance can be explained by the higher initial dislocation density of the forged material, which represents an interstitial-biased sink that leaves a vacancy supersaturation to nucleate cavities. These findings show promise for qualification of PM-HIP Alloy 625 for nuclear applications, although higher dose studies are needed to assess the steady-state irradiated microstructure.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗