Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Off Gas”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Gasbuggy, New Mexico, Hydrologic and Natural Gas Sampling and Analysis Results for 2010

The U.S. Department of Energy (DOE) Office of Legacy Management conducted natural gas sampling for the Gasbuggy, New Mexico, site on July 6 and 7, 2010. Additionally, a water sample was obtained at one well known as the 29-6 Water Hole, several miles west of the Gasbuggy site. Natural gas sampling consists of collecting both gas samples and samples of produced water from gas production wells. Water samples from gas production wells were analyzed for gamma-emitting radionuclides, gross alpha, gross beta, and tritium. Natural gas samples were analyzed for tritium and carbon-14. The one water well sample was analyzed for gamma-emitting radionuclides and tritium. ALS Laboratory Group in Fort Collins, Colorado, analyzed water samples. Isotech Laboratories in Champaign, Illinois, analyzed natural gas samples.

54 ENVIRONMENTAL SCIENCES↗

Quantification and Controls of Wetland Greenhouse Gas Emissions

Wetlands cover only a small fraction of the Earth’s land surface, but have a disproportionately large influence on global climate. Low oxygen conditions in wetland soils slows down decomposition, leading to net carbon dioxide sequestration over long timescales, while also favoring the production of redox sensitive gases such as nitrous oxide and methane. Freshwater marshes in particular sustain large exchanges of greenhouse gases under temperate or tropical climates and favorable nutrient regimes, yet have rarely been studied, leading to poor constraints on the magnitude of marsh gas sources, and the biogeochemical drivers of flux variability. The Sacramento-San Joaquin Delta in California was once a great expanse of tidal and freshwater marshes but underwent drainage for agriculture during the last two centuries. The resulting landscape is unsustainable with extreme rates of land subsidence and oxidation of peat soils lowering the surface elevation of much of the Delta below sea level. Wetland restoration has been proposed as a means to slow further subsidence and rebuild peat however the balance of greenhouse gas exchange in these novel ecosystems is still poorly described. In this dissertation I first explore oxygen availability as a control on the composition and magnitude of greenhouse gas emissions from drained wetland soils. In two separate experiments I quantify both the temporal dynamics of greenhouse gas emission and the kinetic sensitivity of gas production to a wide range of oxygen concentrations. This work demonstrated the very high sensitivity of carbon dioxide, methane, and nitrous oxide production to oxygen availability, in carbon rich wetland soils. I also found the temporal dynamics of gas production to follow a sequence predicted by thermodynamics and observed spatially in other soil or sediment systems. In the latter part of my dissertation I conduct two field studies to quantify greenhouse gas exchange and understand the carbon sources for decomposition in a 1 km2 restored wetland in the Sacramento Delta. By coupling flux measurements at multiple-scales with remote sensing imagery I showed that large methane emissions produce an overall climate warming effect from the wetland for the next several centuries, despite relatively high productivity. I also used radiocarbon analyses of wetland sediment carbon dioxide and methane to show that both bulk peat and recently fixed carbon contribute to decomposition in the wetland, and that their relative importance is regulated by proximity to, and the phenological cycles of, emergent vegetation.

07 ISOTOPE AND RADIATION SOURCES↗

Report on simulation of fission gas and fission product diffusion in UO 2

In UO 2 nuclear fuel, the retention and release of fission gas atoms such as xenon (Xe) are important for nuclear fuel performance by, for example, reducing the fuel thermal conductivity, causing fuel swelling that leads to mechanical interaction with the clad, increasing the plenum pressure and reducing the fuel–clad gap thermal conductivity. We use multi-­scale simulations to determine fission gas diffusion mechanisms as well as the corresponding rates in UO 2 under both intrinsic and irradiation conditions. In addition to Xe and Kr, the fission products Zr, Ru, Ce, Y, La, Sr and Ba have been investigated. Density functional theory (DFT) calculations are used to study formation, binding and migration energies of small clusters of Xe atoms and vacancies. Empirical potential calculations enable us to determine the corresponding entropies and attempt frequencies for migration as well as investigate the properties of large clusters or small fission gas bubbles. A continuum reaction-­diffusion model is developed for Xe and point defects based on the mechanisms and rates obtained from atomistic simulations. Effective fission gas diffusivities are then obtained by solving this set of equations for different chemical and irradiation conditions using the MARMOT phase field code. The predictions are compared to available experimental data. The importance of the large Xe U3O cluster (a Xe atom in a uranium + oxygen vacancy trap site with two bound uranium vacancies) is emphasized, which is a consequence of its high mobility and high binding energy. We find that the Xe U3O cluster gives Xe diffusion coefficients that are higher for intrinsic conditions than under irradiation over a wide range of temperatures. Under irradiation the fast-­moving Xe U3O cluster recombines quickly with irradiation-induced interstitial U ions, while this mechanism is less important for intrinsic conditions. The net result is higher concentration of the Xe U3O cluster for intrinsic conditions than under irradiation. We speculate that differences in the irradiation conditions and their impact on the Xe U3O cluster can explain the wide range of diffusivities reported in experimental studies. However, all vacancy-­mediated mechanisms underestimate the Xe diffusivity compared to the empirical radiation-­enhanced rate used in most fission gas release models. We investigate the possibility that diffusion of small fission gas bubbles or extended Xe-­vacancy clusters may give rise to the observed radiation-­enhanced diffusion coefficient. These studies highlight the importance of U divacancies and an octahedron coordination of uranium vacancies encompassing a Xe fission gas atom. The latter cluster can migrate via a multistep mechanism with a rather low effective barrier, which together with irradiation-induced clusters of uranium vacancies, gives rise to the irradiation-enhanced diffusion coefficient observed in experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Polarized 3He gas circulating technologies for neutron analyzers

We outline our project to develop a circulating polarized helium-3 system for developing of large, quasi-continuously operating neutron analyzers. The project consisted of four areas: 1) Development of robust external cavity narrowed diode laser output with spectral line width < 0.17 nm and power of 2000 W. 2) Development of large glass polarizing cells using cell surface treatments to obtain long relaxation lifetimes. 3) Refinements of the circulation system with an emphasis on gas purification and materials testing. 4) Design/fabrication of a new polarizer system. 5) Preliminary testing of the new polarizer. 1. Developed Robust High-Power Narrowed Laser The optical configuration of the laser was discussed in the proposal and will be reviewed in the body of this report. The external cavity is configured to mutually lock the wavelength of five 10-bar laser stacks. All the logistical milestones were been met and critical subsystems- laser stack manifold and power divider, external laser cavity, and output telescope- were assembled and tested at low power. Each individual bar is narrowed to ~0.05 nm; when combined the laser has a cumulative spectral width of 0.17 nm across the entire beam due to variations of the bars central wavelength by +/- 0.1 nm, which is similar to that of Volume Bragg Grating narrowed laser bars. This configuration eliminates the free-running “pedestal” that occurs in other external cavity diode lasers. The full-scale laser was completed in 2016 and was used in both the older and newer helium polarizers. This laser was operated at 75% power for periods of up to 8 hours. Once installed, the spectrum became slightly broader (~.25 nm) at full power; this is likely due to very slight misalignments that occurred during handling. 2. Developed the processes to create uniform sintered sol-gel coatings. Our work on cell development comprised: 1) Production of large GE180 cells and explore different means of cell preparation, and 2) Development of apply sol-gel coatings to the interior of both borosilicate and aluminosilicate cells. We applied six sol-gel coatings. By modifying the mixture and developing procedures to drain and dry the cell, we produced visually uniform coatings on the interior of the cells. We now have perfected that process as described below in our report. We were able to accelerate the testing of cells using an ex situ method that avoids installing each cell into a polarizer. In the project’s last year, we conducted 38 external tests of 8 different cells. We also installed two sol-gel coated cells in our polarizers. We created cell with long ex situ relaxation lifetimes, one of which exceeded 40 hours. However, when installed in the polarizer the measured lifetime is 8 hours or less. 3. Demonstrated cycling of polarized gas and ex situ cell testing We are now cycling polarized gas from the polarizer to glass vessels and back. This has allowed us, for the first time, to make ex situ T1 measurements of polarizing cells without installing them into the polarizer itself. This has greatly improved our productivity in producing cells and evaluating our cell preparation processes. We continued development of the gas handling system in parallel with fabricating new polarizer. The integrated system was tested by the end of 2016. We now regularly cycle gas into and out of the polarizer. 4. Completed new polarizer infrastructure and control systems. We completed the new polarizer infrastructure in November 2016. The polarizer subsystems are 1) the frame, 2) the oil flow system, 3) the gas handling system, 4) the pressure vessel, with embedded solenoid, 5) cell mounting hardware with heat spreaders, and 6) electrical power and instrumentation. 5. Carried out initial tests of polarizer. We completed initial testing of the polarizer in April and May of 2017. These tests were carried out for periods up to 6 hours with laser power between 750 and 1300 Watts. The laser performed well and the polarization with asymptotic to 45 percent, which was below expectations. This low value resulted from a stationary thermal inversion in the cell that caused most of the laser power to be absorbed near the laser inlet window and deprived the lower portions of the cell of pumping laser light. Possible solutions to this problem include enhanced cooling of the cell near the laser entry and slight detuning of the laser. 6. Ongoing work. Our polarizer development efforts are ongoing to pursue our interest in neutron analyzers, nuclear targets, and providing helium for medical imaging. Current tests in the pipeline include: 1. Testing cooling enhancements to improve laser penetration of spectrally narrow lasers; 2. Testing of a cell with isolation valves that minimizes diffusive contact with gas handling hardware during polarization; 3. Testing of smaller hybrid cells with reduced alkali loading; 4. Producing polarized helium-3 for MRI imaging at the University of Missouri.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Testing of an Iodine and Tritium Removal System for Advanced Tritium Pretreatment Off-Gas

The reprocessing of used nuclear fuel would release volatile radionuclides into the off-gas of a processing plant, including 3 H, 14 C, 85 Kr, and 129 I. For a reprocessing plant sited within the United States and governed by US regulations, the abatement of some or all of these radionuclides from the plant off-gas would be required before discharge of that gas to the environment. A potential simplification of the off-gas management system can be achieved through an efficient advanced tritium pretreatment (ATPT) step in which the UO 2 fuel is oxidized by NO 2 prior to dissolution. Oxidation of the UO 2 fuel matrix results in the release of tritium contained within. Up-front removal of tritium from the fuel in a pretreatment step, followed by the abatement of tritium from the advanced tritium pretreatment off-gas (ATPTOG) stream, can minimize or eliminate the distribution of tritium throughout the plant, also decreasing or eliminating the need for tritium capture on multiple off-gas streams. The use of NO 2 as the oxidant allows tritium pretreatment to be performed at lower temperatures and may result in the quantitative release of iodine from the fuel. A total of five tests examined AgA as a potential iodine sorbent at an operating temperature of 150°C and both 3A MS and silica gel as potential tritium sorbents with an operating temperature of 40°C. 3A MS and silica gel are intended for use as regenerative sorbents, in which the adsorbed tritium (as tritiated water or tritiated nitric acid) is loaded onto the sorbent at operating temperature and then subsequently desorbed at high temperature into a small-volume gas stream for recovery and conversion to a waste form. This testing leaves many fundamental questions regarding the ATPTOG iodine and tritium abatement systems unanswered. These include questions regarding sorbent capacity and sorbate desorption. Overall, this testing indicates that tritium and iodine abatement from an ATPTOG stream by solid sorbents is currently at a low stage of technological development and that deployment of such an abatement system would require substantial additional research and development.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Performance of Silver-Exchanged Mordenite and Silver-Functionalized Silica-Aerogel Under Vessel Off-gas Conditions

US regulations 40 CFR 61, 40 CFR 190, and 10 CFR 20 govern release limits for volatile radionuclides contained in the gaseous effluents of used nuclear fuel (UNF) reprocessing facilities. Of the four volatile radionuclides that are restricted by the release limits ( 3 H, 14 C, 85 Kr, and 129 I) 129 I will require the greatest degree of abatement. Previous studies have shown that overall plant decontamination factor (DF) for 129 I must, at minimum, exceed 1,000 to meet regulatory requirements. Iodine-containing off-gas will be present in the dissolver off-gas, the cell off-gas, the vessel off-gas (VOG), the waste off-gas, and the shear off-gas. The VOG will most likely contain 1%–5% of the total iodine at part per billion (ppb) concentrations. A number of studies have examined iodine abatement from the dissolver off-gas, which contains greater than 95% of the iodine inventory of the plant, but very few have examined the recovery of iodine from the VOG stream. Reduced silver-exchanged mordenite (Ag 0 Z) has been considered a promising iodine sorbent for use in UNF reprocessing plants, but recent efforts have identified silver-functionalized silica-aerogel (AgAerogel) as a potential alternative. The testing reported here reflects a substantial increase in the body of work available on iodine adsorption by both silver sorbents under prototypical VOG conditions. Both I2 and methyl iodide (CH 3 I) adsorption tests have been conducted with Ag 0 Z and AgAerogel at a range of concentrations up to 1,000 ppb. These experiments were performed with two specific aims: (1) to assess the effect of iodine concentration on its adsorption by the sorbent and (2) to compare the performance of Ag 0 Z and AgAerogel in the removal of iodine from a prototypical VOG stream.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Geologic Assessment of the Carbon Sequestration Potential of Paleozoic Shale Gas Reservoirs in Alabama (Final Report)

Organic-rich shale formations are an increasingly important source of natural gas in the United States and have further been recognized to have large capacity for the geologic storage of carbon dioxide. Shale gas plays are active in Cambrian through Mississippian strata of the Appalachian thrust belt and Black Warrior basin of Alabama and are presently being evaluated for their resource and production potential. Gas shales are complex reservoirs and can hold gas both within matrix porosity and fractures, as well as adsorbed on organic matter and other mineral particles. Because of their unique storage duality, they have the ability to hold large volumes of gas, and thus are potentially valuable sinks for CO 2 . Using specific data on CO 2 storage, this study investigates the storage capacity of shale units in Alabama through isotherm and volumetric analysis and is part of research conducted under the Southeastern Regional Carbon Sequestration Partnership (SECARB) Phase III program. Previously, the only assessments of shale gas storage in the SECARB region were those based primarily on formation volume. The SECARB region is defined as the eleven southeastern states of Alabama, Arkansas, Florida, Georgia, Louisiana, Mississippi, North Carolina, South Carolina, Tennessee, Texas, and Virginia. Specifically, this study considers three potential shale sinks in Alabama. The Cambrian Conasauga Formation of the Appalachian thrust belt is geologically the oldest gas shale play in the world and is host to thousands of feet of deformed shale. Preliminary work by Koperna and others first suggested the massive storage potential of this unit. The Devonian Chattanooga Shale is widespread in much of the Black Warrior basin and vicinity and is also found along the margins of the thrust belt. Both of these areas have been sites of exploration and production. An additional thick, unnamed Silurian-Devonian shale exists within the interior of the thrust belt and was grouped with the Chattanooga Shale when calculating storage estimates. The Neal interval of the Mississippian Floyd Shale is found within the southern half of the Black Warrior basin and the southwestern part of the Appalachian thrust belt within facies-related carbonate and sandstone units, but has had limited production success.

54 ENVIRONMENTAL SCIENCES↗

End-Use Savings Shapes Measure Documentation: Boiler Replacement with Air-Source Heat Pump Boiler and Natural Gas Boiler Backup

Building on the successfully completed effort to calibrate and validate the U.S. Department of Energy's ResStock (™) and ComStock (™) models over the past three years, the objective of this work is to produce national data sets that empower analysts working for federal, state, utility, city, and manufacturer stakeholders to answer a broad range of analysis questions. The goal of this work is to develop energy efficiency, electrification, and demand flexibility end-use load shapes (electricity, gas, propane, or fuel oil) that cover a majority of the high-impact, market-ready (or nearly market-ready) measures. "Measures" refers to energy efficiency variables that can be applied to buildings during modeling. An end-use savings shape is the difference in energy consumption between a baseline building and a building with an energy efficiency, electrification, or demand flexibility measure applied. It results in a time-series profile that is broken down by end use and fuel (electricity or on-site gas, propane, or fuel oil use) at each timestep. ComStock is a highly granular, bottom-up model that uses multiple data sources, statistical sampling methods, and advanced building energy simulations to estimate the annual subhourly energy consumption of the commercial building stock across the United States. The baseline model intends to represent the U.S. commercial building stock as it existed in 2018. The methodology and results of the baseline model are discussed in the final technical report of the End-Use Load Profiles project. This documentation focuses on a single end-use savings shape measure - boiler replacement with air-source heat pump boiler with natural gas boiler backup. This measure replaces natural gas boilers for HVAC application by air-source heat pump boilers when applicable and use natural gas boiler backup when the heat pump boiler could not operate due to outdoor air conditions which are below its cutoff temperature. This measure helps to quantify the decarbonization as well as the energy savings potential from the replacement. The measure resulted higher savings in natural gas consumption compared to the increase in electricity consumption, with a ratio of 3. The total natural gas energy consumption was reduced by 41%, whereas the total electricity consumption was increased by 5.3%.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Description of the Gas Sampling and Circulation System for the LYNM PE1-A Experiment

A series of multiphysics experiments, referred to as Physics Experiment 1 (PE1) is underway at the U.S. Nevada National Security Site. The PE1 series includes detonations of three underground chemical explosions. As the name implies, there are a number of experiments investigating the signals generated by the explosion. The experiment series objectives are outlined in a report from Lawrence Livermore National Laboratory.1 One of the experiments is a gas migration experiment. Gas tracers were imbedded in the explosives and gas sampling boreholes were installed in the formation in the test bed. Connected to the monitoring points is a circulation system that moves gas to a central measurement location. This report does not describe the gas analysis or collection systems, but rather the circulation system that provides the gas for measurement. Here, we have combined four project documents into a single report that describes the design, build, installation, testing, and operation of the gas sampling network.

42 ENGINEERING↗

Radiolytic Gas Generation and Pressure Buildup in a Closed System Containing Mo-99 Solution

This study measured radiolytic gas generation and pressure buildup in a sealed stainless-steel system containing alkaline Mo-99 solution with added sodium nitrate as a hydrogen suppressant. In each of two experiments, approximately 200 Ci of Mo-99 solution was transferred into a closed experimental vessel inside a hot cell, isolated, and monitored for pressure rise caused by gas generation during radioactive decay. After pressure buildup, headspace gas samples were collected and analyzed by mass spectrometry to determine hydrogen and oxygen concentrations. The purpose was to quantify the magnitude of pressure buildup in a closed system and to characterize the gas composition produced by radiolysis of the Mo-99 target solution under representative handling and storage conditions. The two experiments used similar total Mo-99 activity but differed in solution volume, headspace volume, and leak integrity. In the first experiment, 197.5 Ci of Mo-99 in 16.92 mL of solution was loaded into a vessel with a 31.1-mL headspace; a small leak was later identified, and the measured peak pressure of 46 psig was extrapolated to about 70 psig in the absence of leakage. The headspace gas from this experiment contained about 21.4% H2 and 63.4% O2, but the composition was influenced by preferential hydrogen loss through the leak. In the second experiment, 193 Ci of Mo-99 in 5.41 mL of solution with 0.46 g NaNO3 was loaded into a vessel with a larger 42.61 mL headspace, and no detectable leak was observed. This experiment reached a peak pressure of 38 psig, and the measured gas composition was approximately 28.2% H2 and 51.5% O2. Because the second experiment was leak-free, it is considered the more reliable indicator of the true pressure buildup and intrinsic radiolytic gas composition of the Mo-99 solution.

Chemerisov, Sergey D.↗

Subsurface Hybrid Power Options for Oil & Gas Production at Deep Ocean Sites

An investment in deep-sea (deep-ocean) hybrid power systems may enable certain off-shore oil and gas exploration and production. Advanced deep-ocean drilling and production operations, locally powered, may provide commercial access to oil and gas reserves otherwise inaccessible. Further, subsea generation of electrical power has the potential of featuring a low carbon output resulting in improved environmental conditions. Such technology therefore, enhances the energy security of the United States in a green and environmentally friendly manner. The objective of this study is to evaluate alternatives and recommend equipment to develop into hybrid energy conversion and storage systems for deep ocean operations. Such power systems will be located on the ocean floor and will be used to power offshore oil and gas exploration and production operations. Such power systems will be located on the oceans floor, and will be used to supply oil and gas exploration activities, as well as drilling operations required to harvest petroleum reserves. The following conceptual hybrid systems have been identified as candidates for powering sub-surface oil and gas production operations: (1) PWR = Pressurized-Water Nuclear Reactor + Lead-Acid Battery; (2) FC1 = Line for Surface O{sub 2} + Well Head Gas + Reformer + PEMFC + Lead-Acid & Li-Ion Batteries; (3) FC2 = Stored O2 + Well Head Gas + Reformer + Fuel Cell + Lead-Acid & Li-Ion Batteries; (4) SV1 = Submersible Vehicle + Stored O{sub 2} + Fuel Cell + Lead-Acid & Li-Ion Batteries; (5) SV2 = Submersible Vehicle + Stored O{sub 2} + Engine or Turbine + Lead-Acid & Li-Ion Batteries; (6) SV3 = Submersible Vehicle + Charge at Docking Station + ZEBRA & Li-Ion Batteries; (7) PWR TEG = PWR + Thermoelectric Generator + Lead-Acid Battery; (8) WELL TEG = Thermoelectric Generator + Well Head Waste Heat + Lead-Acid Battery; (9) GRID = Ocean Floor Electrical Grid + Lead-Acid Battery; and (10) DOC = Deep Ocean Current + Lead-Acid Battery.

36 MATERIALS SCIENCE↗

RESOLVED CO GAS INTERIOR TO THE DUST RINGS OF THE HD 141569 DISK

The disk around HD 141569 is one of a handful of systems whose weak infrared emission is consistent with a debris disk, but still has a significant reservoir of gas. Here we report spatially resolved millimeter observations of the CO(3-2) and CO(1-0) emission as seen with the Submillimeter Array and CARMA. We find that the excitation temperature for CO is lower than expected from cospatial blackbody grains, similar to previous observations of analogous systems, and derive a gas mass that lies between that of gas-rich primordial disks and gas-poor debris disks. The data also indicate a large inner hole in the CO gas distribution and an outer radius that lies interior to the outer scattered light rings. This spatial distribution, with the dust rings just outside the gaseous disk, is consistent with the expected interactions between gas and dust in an optically thin disk. This indicates that gas can have a significant effect on the location of the dust within debris disks.

79 ASTRONOMY AND ASTROPHYSICS↗

Garrotxa cosmological simulations of milky way-sized galaxies: general properties, hot-gas distribution, and missing baryons

We introduce a new set of simulations of Milky Way (MW)-sized galaxies using the AMR code ART + hydrodynamics in a Λ cold dark matter cosmogony. The simulation series is called GARROTXA and it follows the formation of a halo/galaxy from z = 60 to z = 0. The final virial mass of the system is ∼7.4 × 10{sup 11} M {sub ⊙}. Our results are as follows. (a) Contrary to many previous studies, the circular velocity curve shows no central peak and overall agrees with recent MW observations. (b) Other quantities, such as M-∗(6 × 10{sup 10} M {sub ⊙}) and R {sub d} (2.56 kpc), fall well inside the observational MW range. (c) We measure the disk-to-total ratio kinematically and find that D/T = 0.42. (d) The cold-gas fraction and star formation rate at z = 0, on the other hand, fall short of the values estimated for the MW. As a first scientific exploitation of the simulation series, we study the spatial distribution of hot X-ray luminous gas. We have found that most of this X-ray emitting gas is in a halo-like distribution accounting for an important fraction but not all of the missing baryons. An important amount of hot gas is also present in filaments. In all our models there is not a massive disk-like hot-gas distribution dominating the column density. Our analysis of hot-gas mock observations reveals that the homogeneity assumption leads to an overestimation of the total mass by factors of 3–5 or to an underestimation by factors of 0.7–0.1, depending on the used observational method. Finally, we confirm a clear correlation between the total hot-gas mass and the dark matter halo mass of galactic systems.

79 ASTRONOMY AND ASTROPHYSICS↗

HCO{sup +} detection of dust-depleted gas in the inner hole of the LkCa 15 pre-transitional disk

LkCa 15 is an extensively studied star in the Taurus region, known for its pre-transitional disk with a large inner cavity in the dust continuum and normal gas accretion rate. The most popular hypothesis to explain the LkCa 15 data invokes one or more planets to carve out the inner cavity, while gas continues to flow across the gap from the outer disk onto the central star. We present spatially unresolved HCO{sup +} J=4→3 observations of the LkCa 15 disk from the James Clerk Maxwell telescope (JCMT) and model the data with the ProDiMo code. We find that: (1) HCO{sup +} line-wings are clearly detected, certifying the presence of gas in the cavity within ≲50 au of the star. (2) Reproducing the observed line-wing flux requires both a significant suppression of cavity dust (by a factor ≳10{sup 4} compared to the interstellar medium (ISM)) and a substantial increase in the gas scale-height within the cavity (H {sub 0}/R {sub 0} ∼ 0.6). An ISM dust-to-gas ratio (d:g = 10{sup −2}) yields too little line-wing flux, regardless of the scale-height or cavity gas geometry, while a smaller scale-height also under-predicts the flux even with a reduced d:g. (3) The cavity gas mass is consistent with the surface density profile of the outer disk extended inwards to the sublimation radius (corresponding to mass M {sub d} ∼ 0.03 M {sub ⊙}), and masses lower by a factor ≳10 appear to be ruled out.

79 ASTRONOMY AND ASTROPHYSICS↗

Molecular Gas Dominated 50 kpc Ram Pressure Stripped Tail of the Coma Galaxy D100

We have discovered large amounts of molecular gas, as traced by CO emission, in the ram pressure stripped gas tail of the Coma cluster galaxy D100 (GMP 2910), out to large distances of about 50 kpc. D100 has a 60 kpc long, strikingly narrow tail, which is bright in X-rays and Hα. Our observations with the IRAM 30 m telescope reveal in total ∼10{sup 9} M{sub ⊙} H{sub 2} (assuming the standard CO-to-H{sub 2} conversion) in several regions along the tail, thus indicating that molecular gas may dominate its mass. Along the tail, we measure a smooth gradient in the radial velocity of the CO emission that is offset to lower values from the more diffuse Hα gas velocities. Such a dynamic separation of phases may be due to their differential acceleration by ram pressure. D100 is likely being stripped at a high orbital velocity ≳2200 km s{sup −1} by (nearly) peak ram pressure. Combined effects of intra-cluster medium (ICM) viscosity and magnetic fields may be important for the evolution of the stripped interstellar matter. We propose that D100 has reached a continuous mode of stripping of dense gas remaining in its nuclear region. D100 is the second known case of an abundant molecular stripped gas tail, suggesting that conditions in the ICM at the centers of galaxy clusters may be favorable for molecularization. From comparison with other galaxies, we find that there is a good correlation between the CO flux and the Hα surface brightness in ram pressure stripped gas tails, over ∼2 dex.

79 ASTRONOMY AND ASTROPHYSICS↗

{sup 12}CO(J = 1 → 0) On-the-fly Mapping Survey of the Virgo Cluster Spirals. II. Molecular Gas Properties in Different Density Environments

This study investigated the properties of the molecular gas content and star formation activity of 17 Virgo spirals, 21 Ursa Major (UMa) spirals, 13 Pisces spiral galaxies, and a comparison sample of 11 field spiral galaxies with a spatially resolved gas and stellar distribution. The H i-deficient galaxies with a def{sub H i} > 0.4 have a similar range of CO luminosity normalized by the K-band luminosity (L {sub CO}/L {sub K}) like the field spirals, although their CO content can be smaller by up to a factor of 2. The CO, H i, and stellar disk diameters are closely related to each other for both cluster and field galaxies, and the relative diameters of the CO and H i disks grow monotonically and smoothly as the H i-to-stellar disk diameter ratio decreases. Cluster galaxies have a molecular gas consumption time up to 10 times shorter than that of the field comparison sample, suggesting a significant change in the molecular gas content and star formation activity among all the cluster galaxies, even when they do not show any sign of H i stripping. The strongly H i-stripped Virgo cluster galaxies show only a modestly reduced total gas consumption time, indicating that the star formation activity and gas consumption are a highly local (rather than global) phenomenon. Our finding is that the depletion of cold gas by ram-pressure stripping and/or starvation caused by preprocessing in each cluster environment makes galaxies evolve passively.

79 ASTRONOMY AND ASTROPHYSICS↗

Production of Cool Gas in Thermally Driven Outflows

Galactic outflows commonly contain multiphase gas, and its physical origin requires explanation. Using the Cholla Galactic OutfLow Simulations suite of high-resolution isolated galaxy models, we demonstrate the viability of rapid radiative cooling as a source of fast-moving ( v ~ 1000 km s -1 ), cool (10 4 K) gas observed in absorption-line studies of outflows around some star-forming galaxies. By varying the mass loading and geometry of the simulated winds, we identify a region of parameter space that leads to cool gas in outflows. In particular, when using an analytically motivated central feedback model, we find that cooling flows can be produced with reasonable mass-loading rates (${\dot{M}}_{\mathrm{wind}}/{\dot{M}}_{\mathrm{SFR}}\sim 0.5$), provided that the star formation rate surface density is high. When a more realistic clustered feedback model is applied, destruction of high-density clouds near the disk and interactions between different outflow regions indicate that lower mass-loading rates of the hot gas within the feedback region may still produce multiphase outflows. These results suggest an origin for fast-moving cool gas in outflows that does not rely on directly accelerating cool gas from the interstellar medium. Finally, these cooling flows may additionally provide an explanation for the multiphase gas ubiquitously observed in the halos of star-forming galaxies at low redshift.

79 ASTRONOMY AND ASTROPHYSICS↗

Detection of a Substantial Molecular Gas Reservoir in a Brightest Cluster Galaxy at z = 1.7

We report the detection of CO(2–1) emission coincident with the brightest cluster galaxy (BCG) of the high-redshift galaxy cluster SpARCS1049+56, with the Redshift Search Receiver (RSR) on the Large Millimeter Telescope (LMT). We confirm a spectroscopic redshift for the gas of z = 1.7091 ± 0.0004, which is consistent with the systemic redshift of the cluster galaxies of z = 1.709. The line is well fit by a single-component Gaussian with an RSR-resolution-corrected FWHM of 569 ± 63 km s{sup −1}. We see no evidence for multiple velocity components in the gas, as might be expected from the multiple image components seen in near-infrared imaging with the Hubble Space Telescope. We measure the integrated flux of the line to be 3.6 ± 0.3 Jy km s{sup −1}, and using α{sub CO} = 0.8 M {sub ⊙ }(K km s{sup −1} pc{sup 2}){sup −1}, we estimate a total molecular gas mass of 1.1 ± 0.1 × 10{sup 11} M {sub ⊙} and a M {sub H2}/M {sub ⋆} ∼ 0.4. This is the largest gas reservoir detected in a BCG above z > 1 to date. Given the infrared-estimated star formation rate of 860 ± 130 M {sub ⊙} yr{sup −1}, this corresponds to a gas depletion timescale of ∼0.1 Gyr. We discuss several possible mechanisms for depositing such a large gas reservoir to the cluster center—e.g., a cooling flow, a major galaxy–galaxy merger, or the stripping of gas from several galaxies—but conclude that these LMT data are not sufficient to differentiate between them.

79 ASTRONOMY AND ASTROPHYSICS↗