SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Ramped clutch plate prevents damage to gear traing and provides ample linear motion for actuation of microswitch. Operation of device is not affected by number of revolutions which pinion shaft must make to produce required translations. Since ramps in spur gear are conical, device will actuate identically at each mechanical stop.
Circuit minimizes components required to provide six properly timed drive signals from three equal-interval sensor inputs.
The starting transients of solid propellant engines were investigated to develop design principles for predicting transients in high performance igniter and engine configurations. Research and diagnosis were conducted on the processes affecting ignition transients, such as heat flux, igniter, flame spreading over the surface, and nonsteady combustion gas dynamics. Abstracts of published reports related to this research are presented. Topics discussed include: development of an analytical model, analytical prediction of the entire ignition transient, transient behavior of pressure and regression rate during reignition after shut-down, and problems associated with restarting hybrid rocket engines.
The performance quality of movements away and approaches to an airlock by astronauts was tested during parabolic flights for weightlessness simulation. Coordination of movement, orientation and performance capacity of the astronauts were not singificantly disrupted. Observed physiological shifts are characterized by an increase in pulse and respiration rate and an increase in arterial pressure under g-forces, a gradual decrease in these indices during repeated stays in weightlessness or during the prolonged effect of it, by a reduction of the length of postrotational nystagmus and counterrotation illusions under weightless conditions.
Explore the source record for details and available documents.
Heater has stepdown transformer for low voltage range, variable transformer for holding within 0-to-28 volt range, and voltmeters and ammeters to monitor load and wattage. Regulated thermostat controls contactor, permitting heater to cycle.
FORTRAN program calculates torque speed characteristics, electrical characteristics, magnetic flux densities, and weight plus other parameters. Input to program consists of physical dimensions, winding temperatures, winding description, material characteristics, and electrical design parameters.
A three dimensional, nonlinear nozzle admittance relation is developed by solving the wave equation describing finite amplitude oscillatory flow inside the subsonic portion of a choked, slowly convergent axisymmetric nozzle. This nonlinear nozzle admittance relation is then used as a boundary condition in the analysis of nonlinear combustion instability in a cylindrical liquid rocket combustor. In both nozzle and chamber analyses solutions are obtained using the Galerkin method with a series expansion consisting of the first tangential, second tangential, and first radial modes. Using Crocco's time lag model to describe the distributed unsteady combustion process, combustion instability calculations are presented for different values of the following parameters: (1) time lag, (2) interaction index, (3) steady-state Mach number at the nozzle entrance, and (4) chamber length-to-diameter ratio. In each case, limit cycle pressure amplitudes and waveforms are shown for both linear and nonlinear nozzle admittance conditions. These results show that when the amplitudes of the second tangential and first radial modes are considerably smaller than the amplitude of the first tangential mode the inclusion of nozzle nonlinearities has no significant effect on the limiting amplitude and pressure waveforms.
Proposed experiments for analyzing rocket plumes are reported. Two groups of experiments were studied: (1) those that would help define some of the parameters that characterize the plume and (2) those that would enable evaluation of some of the contamination effects of the plume environment on various items of interest. The items investigated, the purpose of the investigation, are given in tabular form.
The steps in the nozzle design process are examined. The nozzle designer's role in defining design requirements and constraints is included along with discussions of each of the three basic phases of the nozzle design process itself: (1) aerodynamic design, in which the gas-contacting surfaces are configured to produce the required performance within the envelope limits; (2) thermal design, in which termal liners and thermal insulators are selected and configured to maintain the surfaces as closely as practical against effects of erosion and to limit the structure temperature to acceptable levels; and (3) structural design, in which materials are selected and configured to support the thermal components and to sustain the predicted loads. Analytical techniques that are used to establish thermal and structural design integrity and to predict nozzle performance are discussed along with methods for nozzle quality assurance. Emphasis is placed on nozzle design and materials for modern high-temperature aluminized propellants. Recurring nozzle design problems of graphite cracking and ejection, differential erosion at material interfaces, lack of sufficient proven nondestructive testing (NDT) techniques, the uncertainty of adhesive bonding, and inadequate definition of material properties, particularly at high temperatures are considered.
Direct characterization procedures were used to determine the relaxation modulus as a function of time, temperature, and state of strain. Using the quasi-elastic method of linearviscoelasticity, these properties were employed in a finite element computer code to analyze a thick-walled, nonlinear viscoelastic cylinder in the state of plane strain bonded to a thin (but stiff) elastic casing and subjected to slow thermal cooling. The viscoelastic solution is then expressed as a sequence of elastic finite element solutions. The strain-dependent character of the relaxation modulus is included by replacing the single relaxation curve used in the linear viscoelastic theory by a family of relaxation functions obtained at various strain levels. These functions may be regarded as a collection of stress histories or responses to specific loads (in this case, step strains) with which the cooldown solution is made to agree by iterations on the modulus and strain level.
Spacecraft contamination of the space shuttle orbiter and accompanying Spacelab payloads is studied. The scattering of molecules from the vernier engines and flash evaporator nozzle after impingement on the orbiter wing surfaces, and the backflow of molecules out of the flash evaporator nozzle plume flow field due to intermolecular collisions in the plume are the problems discussed. A method was formulated for dealing with these problems, and detailed results are given.
Five different engine models were tested covering combinations of all engine categories in current production in the range from 100 to 435 brake horsepower. Engines were divided into five major types: carbureted, fuel injected, direct drive, geared, and turbocharged. Emissions data were categorized by three separate fuel system schedules: baseline, case 1, and case 2. Baseline was defined as the average fuel flow rate established by the fuel system's production tolerance band when operated with the mixture control at the full-rich position. Case 1 was defined as the minimum allowable fuel flow rate established by the engine certification. Case 2 was defined as the fuel rate corresponding to the leanest fuel-air ratio obtainable before a safety limit occurred with the engine operating on a propeller test stand. Safety limits that developed during testing were cylinder-head overheating or inadequate acceleration from a given mode of operation.
The design, analysis, fabrication and testing of a Kevlar-49/HBRF-55A filament wound chamber is reported. The chamber was fabricated and successfully tested to 80% of the design burst pressure. Results of the data reduction and analysis from the hydrotest indicate that the chamber design and fabrication techniques used for the chamber were adequate and the chamber should perform adequately in a static test.
Two position rotary actuator rotates shaft by precisely 180 deg and rotates it back on command. Mechanism consumes 11 watts of power and functions over wide range of temperatures under high vacuum for long unattended periods. Light weight device may be used to flip magnetometer for calibration in magnetic field.
A flywheel hybrid propulsion system is compared with a conventional propulsion system in a test vehicle under intermittent operation. An energy balance is presented for the conventional propulsion system. Results so far indicate especially high energy conversion of the gyro component under dynamic operation along with favorable internal combustion engine conditions.
A small delivery vehicle was equipped with a flywheel-hybrid drive and compared in test stand and driving tests with a conventional drive vehicle. It turned out that with the hybrid drive, energy can be saved and exhaust emissions can be reduced.
This study focuses on establishing the sensitivity of predictions of NO production to uncertainties in altitude, reaction rate coefficients, turbulent mixing rates, and Mach disk size and location. The results show that relatively large variations in parameters related to these phenomena had surprisingly little effect on predicted NO production.