Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

The microstructure and composition of equilibrium phases formed in hypoeutectic Te-In alloy during solidification

As a key tellurium atoms evaporation source for ultraviolet detection photocathode, the hypoeutectic Te{sub 75}In{sub 25} alloy was prepared by employing a slow solidification speed of about 10{sup −2} K/s. The microstructure and chemical composition of the equilibrium phases formed in the as-prepared alloy were studied in this research work. The experimental results show that the as-prepared Te-In alloy was constituted by primary In{sub 2}Te{sub 5} phase and eutectic In{sub 2}Te{sub 5}/Te phases. The eutectic In{sub 2}Te{sub 5}/Te phases are distributed in the grain boundaries of primary In{sub 2}Te{sub 5} phase. With the slow solidification speed, a pure eutectic Te phase without any excessive indium solute was obtained, where Te content of eutectic Te phase is 100 mass%. Moreover, it can be considered that the stress between the In{sub 2}Te{sub 5} and Te phases plays an important role in reducing the tellurium vapor pressure in Te{sub 75}In{sub 25} alloy. - Highlights: • The microstructure of Te-In alloy as an evaporation source was analyzed. • A pure eutectic Te phase was obtained by using a slow solidification speed method. • The relation between vapor pressure and inner-stress in the alloy was discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Microstructural variation through weld thickness and mechanical properties of peened friction stir welded 6061 aluminum alloy joints

The current study examined the effect of microstructure variation on the development of mechanical properties in friction stir welded joints of 6061-T6 aluminum alloy, which were subsequently processed by shot peening (SP). Following to FSW, fatigue specimens were extracted perpendicularly to the welding direction. Surface Skimming to 0.5 mm from crown and root sides of the joint was made and SP was later applied on the two sides using ceramic shots of two different Almen intensities of 0.18 mmA and 0.24 mmA. Microstructural examination by electron back scattered diffraction (EBSD) indicated variation in the grain refinement of the weld zone, with coarsest grains (5 μm) at the crown side and finest grains (2 μm) at the root side. Reduction of microhardness to 60 HV occurred in the weld zone for samples in FSW condition. Application of SP promoted significant strain hardening at the crown side, with Almen intensities of 0.24 mmA providing maximum increase in microhardness to 120 HV. On the contrary, only a maximum microhardness of 75 HV was obtained at the root side. The difference in strain hardening capability at the two sides was strongly dependent on grain size. The two Almen intensities produced similar distribution of compressive residual stresses in the subsurface regions that led to enhance the fatigue strength to the level of base metal for N ≥ 10{sup 5} cycles. Yet, the increase in fatigue strength was more pronounced with increasing Almen intensity to 0.24 mmA, demonstrating further enhancement by strain hardening. - Highlights: • Grain refinement was observed after friction stir welding of AA 6061-T6. • Reduction in microhardness and fatigue strength were obtained after welding. • Variation in grain refinement led to different hardening behavior after peening. • Shot peening induced beneficial compressive residual stresses. • Shot peening and surface skimming markedly improved the fatigue performance.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Microstructural control of FeCrAl alloys using Mo and Nb additions

The effects of Mo and Nb additions on the microstructure and mechanical properties of two FeCrAl alloys were studied in this paper. Fine and uniform recrystallized grain structures (~ 20–30 μm) were achieved in both alloys through suitable annealing after warm-rolling. The formation of Fe 2 Nb-type Laves phase precipitates in the Nb-containing FeCrAl alloy effectively stabilized the deformed and recrystallized microstructures. The Mo-containing FeCrAl alloy exhibited strong γ texture fiber after annealing at 650–900 °C, whereas the annealed Nb-containing FeCrAl alloy had much weaker texture. Finally, both strength and ductility decreased as the grain size increased in both alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Pre-compression effect on microstructure evolution of extruded pure polycrystalline magnesium during reversed tension load

Highlights: • Number of twin variants under compression along ED is dependent on grain orientation. • Tension after pre-compression results in low-SF twinning and secondary twinning. • Secondary twinning is facilitated by increasing pre-compression. • Sub-grains due to twinning enhance material strength. - Abstract: The microstructure evolution of extruded pure polycrystalline magnesium under compression followed by subsequent tension in ambient air was investigated. Solid round dog-bone shaped specimens were compressed along the extrusion direction (ED) to − 7.3% and − 12.8% true strains, respectively, and then tensioned along the ED to failure. Electron backscatter diffraction (EBSD) was used to examine the microstructure evolution using companion specimens unloaded at multiple points along the deformation curves. Pre-compression along the ED resulted in {10 1-bar 2} tension twinning which increased in volume with increasing strain until exhaustion at approximately − 10.5% true strain. Tensile reloading of the pre-compressed specimens led to a combination of low Schmid factor twinning, detwinning, and secondary {10 1-bar 2} tension twinning. Detwinning was more significant than secondary twinning in the − 7.3% pre-compressed specimens, where only one secondary twin variant was observed. {10 1-bar 2} secondary twinning was more significant in the − 12.8% pre-compressed specimens, where up to three secondary twin variants were observed. After complete detwinning of primary twins, the secondary twins were retained and appeared as sub-grains. The residual sub-grains resulted from secondary twinning may provide a strengthening mechanism for wrought Mg alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Through-thickness microstructural evolution during grain boundary engineering type thermomechanical processing and its implication on sensitization behavior in austenitic stainless steel

Highlights: • GBE-treated 304L steel exhibits thickness-dependent microstructural evolution. • Degree of sensitization increases from surface to interior in GBE specimen. • Low fractal dimension and large TRD size lead to lesser sensitization at surface. • As-received specimen shows high albeit thickness-independent sensitization behavior. • Higher residual strain leads to higher sensitization at surface of deformed sample. - Abstract: Through-thickness microstructural variations and their synergistic influence on degree of sensitization in grain boundary engineering (GBE) treated 304L stainless steel was compared with solution-annealed and marginally cold-worked (~ 3% thickness reduction) specimens. The solution-annealed specimen has shown higher degree of sensitization due to the presence of lower fraction of Σ3 (as well as other low Σ CSL) boundaries and dominant random high-angle boundaries (RHAGBs) connectivity. However, it has shown thickness-independent sensitization behavior as grain boundary character distribution, residual strain and grain boundary network topology towards thickness direction are similar. Owing to higher residual strain, as revealed by local misorientation analysis, the cold-worked specimen showed maximum degree of sensitization (higher than solution-annealed condition) at surface. The GBE specimen has shown much lower degree of sensitization at surface due to higher-fraction of Σ3 boundaries and discontinuous RHAGBs connectivity. However, increasing fraction of RHAGBs and their connectivity, as confirmed by twinning-related domain and fractal analysis, cause more sensitization at interior of this specimen. In spite of this, the degree of sensitization at the interior of GBE specimen is lower than the solution-annealed or cold-worked specimen. Even though the residual strain in GBE specimen is higher than the solution-annealed condition, the lower degree of sensitization indicates that the grain boundary character distribution and grain boundary network topology have higher implication than residual strain in controlling sensitization.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure and mechanical properties of extruded Mg-Gd-Y-Zn-Zr alloys filled with intragranular LPSO phases

Highlights: • Intragranular thin-platelet LPSO phases strongly restrict the DRX. • The low extrusion ratio fails to widely break the intragranular LPSO. • The large extrusion ratio results in the full DRX via the CDRX mechanism. • Finer DRX-ed grains and LPSO induce the higher yield strength and elongation. • The larger grain size causes an increase in the strain hardening rate. - Abstract: A comparison has been made on the dynamic recrystallization (DRX), texture, and mechanical properties of the Mg-5.5Gd-4.4Y-1.1Zn-0.5Zr (wt%) alloys extruded with different ratios (ER, 36 and 7.1). Intragranular long-period stacking ordered (LPSO) phases strongly restrict the DRX by restraining the lattice rotation of α-Mg grains and hindering the migration of the boundaries of DRX-ed grains. Extrusion with ER of 36 can widely break the intragranular LPSO phases and create a fully DRX-ed microstructure with a relatively random texture, while the lower ER of 7.1 fails to break the LPSO and leads to a bimodal microstructure with a strong basal fiber texture. Finer DRX-ed grains and smaller LPSO phases account for the superior tensile yield strength and elongation of the ER36 alloy. However, the ultimate tensile strength of the ER7.1 alloy catches up because its larger grain size causes an increase in the strain hardening rate.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Evolution of microstructures and mechanical properties during solution treatment of a Ti–V–Mo-containing high‑manganese cryogenic steel

Highlights: • High-Mn cryogenic steels are getting the spotlight in the cryogenic market. • The grain size grew slowly and the yield strength remained almost stabilized with an increase of solutionizing temperature. • The Hall–Petch strengthening coefficient for yield strength was small, estimated to be 153 MPa μm{sup 0.5}. • The weakening effect of solutionizing temperature on grain size was attributed to the nano-sized (Ti, V, Mo)C precipitate. - Abstract: The effect of solution treatment on the microstructure and mechanical properties of a high‑manganese (Mn) twin-induced plastic (TWIP) cryogenic steel that was alloyed from elemental titanium (Ti), vanadium (V) and molybdenum (Mo) was investigated by a variety of techniques such as microstructural characterization, room tensile testing and − 196 °C impact testing. The austenite grain size grew slowly with an increase of the solutionizing temperature (ST). The relatively weak effect of the ST on the austenite grain size is attributed to the superior thermal stability and coarsening resistance of the (Ti, V, Mo)C precipitate, which hindered austenite grain growth. An increase in ST improved the low-temperature toughness (LTT) significantly and decreased the strain hardening rate (SHR), but had no significant effect on the yield strength. The Hall–Petch strengthening coefficient for yield strength was small, and was estimated to be 153 MPa μm{sup 0.5}. Undissolved large-sized chromium (Cr) carbide can deteriorate the LTT significantly. Because of its excellent mechanical properties, high-Mn steel that was alloyed by elemental Ti, V and Mo can be used to manufacture storage tanks for liquefied natural gas.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure control to improve creep strength of alumina-forming austenitic heat-resistant steel by pre-strain

Highlights: • The effect of pre-strain on creep strength of AFA steel was studied. • The creep test was performed at 700°C and 200Mpa, and the aging test was carried out using box furnace at 700°C to simulate the microstructural evolution during creep. • Microstuctural evolution was observed by using SEM, EBSD, and TEM to investigate the relationship between creep strength and microstructure. - Abstract: At 700 °C and 200 MPa, the creep rupture time of W-containing alumina-forming austenitic heat-resistant (WAFA) steel increases from 1044 to 3119 h by pre-strain. Pre-strain introduces a lot of dislocation into the matrix and most of the dislocations remain stable to the end of creep without recovery and recrystallization. In addition, the dislocations have enabled secondary NbC and Laves phase to be uniformly distributed and refined. However, the dislocations lower grain boundary strength due to the coarsening of precipitates along grain boundaries Therefore, the increase in the creep rupture time in spite of deterioration of grain boundary strength is attributed to the dislocation strengthening and enhanced precipitation hardening within grains.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Interactive microstructural phenomena during non-isothermal annealing of an Al-Mg-Si-Cu alloy

Highlights: • A non-isothermal annealing process that is concurrent with precipitation is investigated. • The mechanism of grain refinement through the interactions of precipitation, recovery and recrystallization is identified. • The combination of non-isothermal annealing and proper pre-deformation temper condition tetrads recovery. • Massive recrystallization nucleation is achieved by delaying recovery. • The growth of recrystallized grains is controlled by coarsening of precipitates that pin the grain boundaries. - Abstract: Interactions between precipitation, recovery and recrystallization during a non-isothermal annealing process in an Al-Mg-Si-Cu alloy have been investigated through a comprehensive experimental analysis. Non-isothermal annealing with a slow heating rate that starts from a low temperature is found to promote homogeneous nucleation of precipitates. The uniformly distributed precipitates limit the extent of recovery, which in turn facilitates extensive nucleation of new grains within the deformed microstructure. The growth of the recrystallized grains is strongly controlled through pinning of grain boundaries by precipitates. During the final stages of annealing, enhanced diffusion at the recrystallization front leads to preferential precipitate coarsening, release of grain boundaries from precipitates pinning, and completion of recrystallization. These interactive microstructural phenomena explain the effectiveness of a non-isothermal annealing route combined with an adequate level of deformation in obtaining a fine-grained recrystallized structure.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Ni content on the microstructure and mechanical properties of weld metal with both-side submerged arc welding technique

Highlights: • This manuscript primarily studied the effects of Ni content on the K65 weld metals; • Increase Ni content could significantly improve the strength and low temperature impact toughness of the weld metal. • The beneficial effect of Ni is attributed to its positive effect on phase transformation. • GBF keeps K-S or N-W relations only with one austenite and the variants belong to the same bain group are two reasons. • The M/A islands are considered to be another reason for the reduced toughness. - Abstract: The effects of nickel (Ni) content on the mechanical properties and microstructure evolution in the weld metals of commercial K65 oil and gas pipeline steel were studied. Increase Ni content could significantly improve the strength and low temperature impact toughness (−40 °C and −60 °C) of the weld metal. The above influences of Ni were attributed to the formation of predominant acicular ferrite (AF), at the expense of grain boundary ferrite (GBF), ferrite side plates (FSP) and martensite/austenite (M/A) constituent in weld metal. EBSD results indicated that GBF keeps K-S or N-W relations only with the prior austensite grain that belongs to one side of the grain boundary and the variants belong to the same bain group which always forms low angle boundary. Moreover, the retained austenite as one part of M/A constituent was mainly found in the weld metal with lower Ni content. It indicated that the transformation process could be promoted more completely by the increase of Ni content. The mechanism of the toughness improvement brought by Ni increasing was ascribed to the relatively uniform transformation to final microstructure, which reduces the appearance of GBF and M/A constituents.

36 MATERIALS SCIENCE↗
DOE OSTI2018

The effect of finish rolling temperature and tempering on the microstructure, mechanical properties and dislocation density of direct-quenched steel

Highlights: • The effect of thermomechanical treatment and tempering on direct-quenched steel has been studied. • Dislocation density of direct-quenched and tempered martensite is evaluated using both TEM and Williamson-Hall method. • Statistical analysis has been performed to study the effect of different factors on toughness of direct-quenched martensite. - Abstract: A unique batch tempering treatment for industrial scale direct-quenched steel coils has been studied using laboratory simulations. The tempering treatment was non-isothermal with slow heating to 570 °C and slow cooling to simulate the tempering of large steel coils. The paper presents the effect of finishing rolling temperature (FRT) relative to the non-recrystallization temperature (T{sub NR}) and the effect of long time tempering on the microstructure, dislocation density and mechanical properties of direct-quenched coiled strips. Conditioning austenite below the recrystallization stop temperature resulted in a finer effective grain size distribution, which correlated strongly with the impact toughness of the final product. Furthermore low finish rolling temperature resulted in partially ferritic microstructures while higher finishing rolling temperatures led to mixtures of bainite and martensite. Dislocation densities determined with TEM and XRD showed somewhat different trends regarding the effect of tempering: intra-lath dislocation density, as measured with TEM, showed a statistically significant drop in only one case, while XRD analysis indicated a drop in all cases. Furthermore, no significant correlation between finishing rolling temperature and dislocation density existed in XRD studies. The XRD results indicate that the decrease in dislocation density corresponds to about 100 MPa lower dislocation strengthening. However, precipitation hardening and potential internal micro stress relief compensates this as yield strength remains unchanged or even increases during tempering.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effects of the rolling temperature on microstructure and mechanical properties of 2Cr13/316L laminated composites prepared by accumulative roll-bonding (ARB)

Highlights: • The rolling temperature affects the grain size and microstructural phases of the composite plates. • The rolling temperature affects tensile strength and bending strength of 2Cr13/316L properties of the composite plates. • The temperature gradient and thermal deformation of center and outside regions are different during rolling process. • Composite plate with higher strength and elongation can be obtained by rolling processes. - Abstract: The microstructure and mechanical properties of 2Cr13/316L composite plates by hot-rolling at different rolling temperatures of 1130 °C, 1180 °C, 1250 °C, 1300 °C are investigated in details. With the increase of the rolling temperature, the tensile strength and bending strength of 2Cr13/316Lwere reduced first and then increased slightly due to the coarsening of grains and the increasing of ferrite content in 2Cr13 layers. The highest tensile elongation is obtained at the composite plate with rolling temperature of 1180 °C. 2Cr13/316L composite plates obtained by hot rolling processes were able to withstand larger bending deformation, and no cracks or interfacial delamination can be found in the bending process because of a strong combined interface.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure and mechanical performance of welded joint between a novel heat-resistant steel and Inconel 617 weld metal

Highlights: • MGBs were suspected as the DDC crack source during high-temperature tensile test. • Microhardness variations in different passes of joint denote grain refinement effect induced by the multi-pass welds. • After tensile test, changes in microhardness can be attributed to the extent of deformation and amount of precipitation. - Abstract: In the present study, the microstructure and mechanical performance of a tungsten inert gas welded joint between a novel heat-resistant austenitic steel and Inconel 617 weld metal were examined. Migrated grain boundaries were discovered more frequently in the lower portion of the weld metal that solidifies in austenite type. Ti-rich precipitates were observed in weld metal and Cr-rich and Nb-rich precipitates were observed in base metal. The fusion boundary area had the lowest impact toughness due to the large non-homogeneity of the microstructure. Microhardness profiles of the joint were obtained and the backing passes were found to produce the highest microhardness values, which was caused by the grain refinement effect. Ductile failure with slipping separation occurred in those joints ruptured after tensile tests at both room temperature and 923 K. In addition, multiscale precipitates in the joint after high-temperature tensile tests were inspected, where it was found that nanoscale particles contributed to the high-temperature resistance of the joint. Furthermore, microhardness changes in the joint after tensile tests were analysed according to the precipitation and strain-hardening mechanism.

36 MATERIALS SCIENCE↗
DOE OSTI2018

The influence of power spinning and annealing temperature on microstructures and properties of Cu-Sn alloy

Highlights: • The strengthening effect of power spinning is mainly achieved by strengthening fine grains and dislocations. • Twins formed by the aggregation and overlapping of stacking faults grow and widen • In power spinning of Cu-Sn alloy, plastic deformation is primarily powered by dislocation sliding. - Abstract: Electron back scatter diffraction pattern (EBSD), metallographic microscope (OM) and transmission electron microscope (TEM) are used to analyze the microstructural state of the Cu-Sn alloy before and after power spinning and annealing. The results show that after power spinning, the α phase grains are refined and gradually evolve into small and fine α{sub II} and deformed α{sub III} crystal grains, with an average grain size of about 2.2 μm. Work hardening results in massive network-like subgrain boundaries distributed in power spinning microstructure. Annealing at 400 °C contributes to the formation of dislocation cells and stacking faults, and high-angle grain boundaries (HABS) start to migrate and slide. After the formation of less defective equiaxed grains at 500 °C, twins continue to grow and widen based through continuous accumulation of stacking faults. Further testing of mechanical properties reveals that power spinning is conducive to the improvement of mechanical properties of Cu-Sn alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Annealing-induced microstructural evolution and mechanical anisotropy improvement of the Mg-Gd-Y-Zr alloy processed by hot ring rolling

Highlights: • Growth of SRX grains in GBR is random, while that of TBR is anisotropic. • The new texture component in annealed MR weakens the anisotropy obviously. • T6 treatment leads to an excellent comprehensive mechanical property. - Abstract: Hot ring rolling (HRR) is widely used to fabricate large-size seamless ring-shape components. However, this process produces a severe mechanical anisotropy, which is not acceptable in practical industrial application and should be avoided. This paper reports the annealing-induced microstructural evolution and mechanical anisotropy improvement of HRRed Mg-8.12Gd-1.82Y-0.35Zr alloy ring. Results show that annealing treatment could improve the microstructural homogeneity of the ring owing to the occurrence of static recrystallization (SRX). SRX grains are preferentially formed at twin boundaries and initial grain boundaries due to high dislocation density, high level of stored energy, and stress concentration. Twin boundaries, to some extent, can suppress the migration of SRX grain boundaries. In addition, occurrence of SRX weakens the texture intensity and basal pole inclination, leading to a decrease in the mechanical anisotropy of the ring. Considering the weakened anisotropy, comparable strength, and improved ductility, annealing + aging (T6), compared with direct aging (T5), is a more suitable heat treatment schedule for the HRRed Mg-8.12Gd-1.82Y-0.35Zr alloy ring.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure and texture evolution of deformed Mg-Zn alloy during recrystallization

Highlights: • The texture intensity in the Mg-Zn alloy relied on the microstructure. • Fine DRXed grains showed a fiber texture distributing between <10.0> and <11.0>. • Coarse DRXed grains mainly exhibited <11.0> fiber texture. • The preferred growth of <11.0> oriented grains resulted in texture evolution. - Abstract: The microstructure and texture evolution of Mg-Zn alloy during recrystallization was investigated by EBSD in the present study. Deformed region, fine DRXed region and coarse DRXed region were obtained in Mg-Zn alloy during deformation. It was found that the texture intensity in DRXed region was weaker compared with the deformed region. The second phase at grain boundaries resulted in the formation of fine DRXed grains with weaker texture compared with the coarse DRXed region. Additionally, a remarkable grain-size driven textural transition from <10.0>–<11.0> texture to <11.0> texture were detected with the growth of DRXed grains. The recrystallized grains with small grain size showed a fiber texture distributing homogeneously between <10.0> and <11.0>, while <11.0> fiber texture was predominant for the large recrystallized grains. It is suggested that <11.0> oriented grains grew faster than other oriented grains, which was ascribed to larger misorientation between <11.0> oriented grains and their neighboring grains.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Cascading microstructures in aluminum-steel interfaces created by impact welding

With the rising need to develop light weight structures joining dissimilar metals is inevitable. Thus a fundamental understanding of the microstructure evolution and bond formation mechanism is necessary. In this work we probe the welded interface in aluminum and steel joined using vaporizing foil actuator welding (VFAW) a novel impact welding process. The goal of such a detailed characterization campaign is to understand the bond formation mechanism. The study demonstrates that the interfacial microstructure has a pronounced hierarchical nature. At the macro scale, the interface is characterized by a wavy interface which is a result of extensive plastic deformation that accompanies the process. Detailed transmission electron microscopy shows evidence for the formation of a liquid film at the interface resulting in significant inter diffusion of Fe. The solidified structure at the interface consisted of crystalline α-Al and an amorphous metastable Al-Fe intermetallic compound similar to the observations in rapid solidification of Al-Fe alloys. The sub-nm scale characterization of the interface using atom probe tomography showed two distinct zones 1. A magnesium (5 at.%) and oxygen (15 at.%) rich (not detectable using energy dispersive spectroscopy) which was probably from the decomposition of the surface oxide film 2. The rapidly solidified reaction zone consisting of primary crystalline α-Al and an amorphous Al-Fe (15 at.%)-O (0.5 at.%)-Si (1.5 at.%).Based on these observations a mechanism for the bond formation is presented.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructural and micro-mechanical analysis of 14YWT nanostructured Ferritic alloy after varying thermo-mechanical processing paths into tubing

Microstructural analyses and micro-pillar compression were conducted on 14YWT nanostructured ferritic alloy (NFA) to compare different processing pathways: hydrostatic extrusion and Pilger processing with varying annealing temperatures into thin walled tubing, and after hot extrusion and cross-rolling into a plate. Hydrostatic extrusion at 815 °C resulted in the smallest grain sizes and highest yield strength of 1.20 GPa. Pilger processing with annealing at 800 °C had fine grained regions and bands of coarse grains, leading to a large variation in yield strength of 0.9–1.40 GPa. Higher annealing temperatures of 1200 °C after pilger processing significantly increased the grain size and lowered the yield strength to 1.01 GPa. These tubes showed a stronger (111) crystallographic texture in the normal direction and elongated grains in the extrusion direction. Characterization of the nano-oxides using TEM reveals more numerous, smaller oxides present in tubing processed at lower temperatures. Overall, this work shows NFA tubing after hydrostatic extrusion and pilger processing can lead to fine grained microstructures and texturing leading to higher yield strengths at lower annealing temperatures (e.g. 800 °C).

14YWT↗