Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Graphite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Thermal Charging Study of Compressed Expanded Natural Graphite/Phase Change Material Composites

The thermal charging performance of phase change materials, specifically paraffin wax, combined with compressed expanded natural graphite foam is studied under constant heat flux and constant temperature conditions. By varying the heat flux between 0.39 W/cm2 and 1.55 W/cm2 or maintaining a boundary temperature of 60 C for four graphite foam bulk densities, the impact on the rate of thermal energy storage is discussed. Thermal charging experiments indicate that thermal conductivity of the composite is an insufficient metric to compare the influence of graphite foam on the rate of thermal energy storage of the PCM composite. By dividing the latent heat of the composite by the time to melt for various boundary conditions and graphite foam bulk densities, it is determined that bulk density selection is dependent on the applied boundary condition. A greater bulk density is advantageous for samples exposed to a constant temperature near the melting temperature as compared to constant heat flux conditions where a lower bulk density is adequate. Furthermore, the anisotropic nature of graphite foam bulk densities greater than 50 kg/m3 is shown to have an insignificant impact on the rate of thermal charging. These experimental results are used to validate a computational model for future use in the design of thermal batteries for waste heat recovery.

Compressed expanded natural graphite↗

Initial ASME code rule analysis on Simple and Full assessment

ASME & ASTM codes present simple and full assessment methodologies to qualify nuclear grade graphite components. This report explains the theory behind the statistical portion of the codes and describes the issues discussed in a 2020 workshop in the simple assessment, as well as the full assessment. The methodology for the full assessment was developed by Hindley []. He used a validation methodology to match the experimental average failure load of test specimens from several geometries to the calculated 50% POF load to tune the grouping criteria parameters based on an RMSE penalty function. The grouping criteria consists of a minimum volume to satisfy the weakest link theory of the Weibull distribution and a minimum stress range parameter. Hindley’s work found a minimum link volume of 10 times the grain size and a stress range parameter of 7% [satisfy the validation requirements. Several studies found that the link volume of 10 times the grain size was not satisfactory for the volume grouping criteria for graphite grades with fine grains. ASME 2021 code adopted a new volume grouping criteria based on fracture toughness for calculation of the process zone volume. However, errors were found in the ASME 2021 code process zone volume equation and the question is now open as to what volume grouping criteria is satisfactory. This report presents results from sensitivity studies that were done to evaluate the volume grouping criteria effect on the full assessment POF. This report also presents results from sensitivity studies on other aspects of the code that affect the POF, the mesh size and the choice of the Weibull threshold parameter. All three sensitivity studies: the volume grouping criteria, the mesh size, and the threshold parameter choice are found to affect the component qualification decision for components of structural reliability class 1 (SRC-1). The sensitivity analysis results are presented in the body of the report for NBG-18, which is the same grade of graphite as Hindley used in his thesis. Results from NBG-17, IG-110, 2114, and PCEA are presented in the Appendix. For NBG-18, it was found that increasing the threshold increases the POF, finer meshes result in higher POFs, and that smaller link volume requirements lead to higher POFs (which is inconsistent with Hindley’s findings). This report proposes a new validation study similar to Hindley’s []. The purpose of the new validation study is to tune the threshold, mesh size and grouping criteria based on results from multiple grades of graphite, including finer grain graphites T220 (1-3 microns) and NG-CT-50 (5 microns). The test specimens will be broken at 3 labs, such that we can measure between lab measurement variability, with at least 5 test specimens per lab such that the within lab uncertainty can also be measured. Hindley’s validation method tried matching the average experimental load with the median. The future study will attempt to match failures at lower percentiles, which would be closer to the SRC POF limit. We are currently looking into what geometries make sense and the best method to measure multi-axial stress states. These design decisions are still being set.

36 MATERIALS SCIENCE↗

Coupled field-structural analysis of HGTR fuel brick using ABAQUS

High-temperature, gas-cooled reactors (HTGRs) are usually helium-gas cooled, with a graphite core that can operate at reactor outlet temperatures much higher than can conventional light water reactors. In HTGRs, graphite components moderate and reflect neutrons. During reactor operation, high temperature and high irradiation cause damage to the graphite crystal and grains and create other defects. This cumulative structural damage during the reactor lifetime leads to changes in graphite properties, which can alter the ability to support the designed loads. The aim of the present research is to develop a finite-element code using commercially available ABAQUS software for the structural integrity analysis of graphite core components under extreme temperature and irradiation conditions. In addition, the Reactor Geometry Generator tool-kit, developed at Argonne National Laboratory, is used to generate finite-element mesh for complex geometries such as fuel bricks with multiple pin holes and coolant flow channels. This paper presents the proposed concept and discusses results of stress analysis simulations of a fuel block with H-451 grade material properties. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

TREAT reactor LEU fuel-clad chemical interaction empirical modeling analysis

DOE is converting TREAT (Transient Reactor Test) facility from its existing highly enriched uranium (HEU) core to a low-enriched uranium (LEU) core. In order to assess the magnitude of chemical interaction between fuel and cladding materials during physical contact under expected TREAT operational limits, planned transients tests, and reactivity accident scenarios, a combination of experimental testing and thermodynamic modeling was performed to predict the expected chemical interactions among fuel and cladding chemical constituents. Thermodynamic calculations were then validated with empirical data from experiments that emulate TREAT's expected upper operational limits. Pellet samples composed of LEU oxide powder dispersed in a graphite matrix had intimate contact with zirconium-based alloy cladding. The samples were subjected to long-term isothermal heating under high vacuum. Specimen characterization consisted of scanning electron microscopy, x-ray diffraction analysis, and x-ray tomography. ThermoCalc software and Ellingham's diagrams were used for thermodynamic calculations. The X-ray tomography and SEM analysis of the pellets showed a homogeneous distribution of UO{sub 2} particles within the graphite matrix with isolated larger UO{sub 2} agglomerates. The SEM analysis showed the formation of a lamellar structure between the large UO{sub 2} agglomerate and the graphite matrix. This is an indication that diffusion is taking place at a rather moderate temperature and reaction time during the pellet fabrication. Secondary phases, with high Al and Mg content, were detected inside a UO{sub 2} agglomerate using SEM in SE/EBSD mode and chemical analysis with EDS. LEU feedstock impurities, as Al and Mg, seem to promote the chemical reactivity between UO{sub 2} particles and graphite matrix. XRD analysis of a pellet sample showed the presence of UO{sub 2} and graphite, but no other crystalline phases were detected with this technique. Thermodynamic analysis through the use of Ellingham diagrams showed that within TREAT's operational to reactivity accident temperature (278-820 Celsius degrees), UO{sub 2} can be reduced to U metal by Zr due to a more favorable ΔG for the oxidation of Zr.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Use of spectral shift to greatly improve uranium utilisation in FHR designs

Fluoride-salt-cooled high-temperature reactors (FHRs) are thermal-spectrum nuclear reactors defined by their use of liquid-fluoride-salt coolants, together with tri-isotropic (TRISO)-coated particle fuels and graphite moderator materials (Forsberg, 2004). FHRs are also characterized by their improved thermodynamic efficiency relative to gas-cooled reactors. The liquid salt coolant is designed to operate with high core outlet temperature and nearly atmosphere pressure. These features allow the FHR to possess higher core power density compared to gas-cooled TRISO-based systems. However, industry fabrication limitations result in a low volumetric fraction of fuel kernel in TRISO particles. In order to obtain reasonable operation periods, the enrichment needs to be in the high LEU (low enriched uranium) range as was proposed in the original design (Greene, 2010). Recent studies (Ilas, 2014) presented newly repurposed SmAHTR-CTC reactor concept that relies on prior experience obtained from the 2010 initial SmAHTR design (Greene, 2010). This design consists of 19 hexagonal fuel assemblies arranged in a 3-ring hexagonal geometry with 18 fuel plates each. The active length of fuel plates in each fuel assembly is 4 meters. The proposed SmAHTR-CTC achieves substantial improvements from the neutronic performance standpoint over the original concept. The results indicate that a fuel cycle length of over two years with discharged fuel burnup of 40 gigawatt-day per metric ton of initial heavy metal (HM) is possible with an 8% fuel enrichment in a once-through fuel cycle. However, the lower uranium enrichment loading requires a more frequent refueling strategy and hence considerably reduces the cycle length. It is necessary to achieve reasonable cycle length values but at the same time to extend the residence time of the fuel, especially since the costs associated with TRISO-fuel are substantially higher (Shropshire et al., 2008) than traditional UO{sub 2} fuel ($10,000/kg for TRISO vs $200/kg for UO{sub 2}). This paper presents an approach to extend the operational time and improve fuel utilization of FHR by means of spectral shift control. This is achieved by incorporating movable graphite structures into the design, instead of the static graphite blocks presently envisaged. At beginning of life (BOL), the graphite structures are withdrawn. The reactor is under-moderated, with excess neutrons being primarily captured in {sup 238}U, breeding {sup 239}Pu. Towards the end of life (EOL), the graphite structures are inserted, thermalizing the neutron spectrum and increasing reactivity. The extra {sup 239}Pu bred during the cycle is then burned, allowing the cycle and discharge burnup to be extended. Such movable structures regime should be feasible from an engineering point of view, given that it is broadly equivalent to inserting and withdrawing control rods. The preliminary results indicate that such a design may considerably improve the fuel utilization.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Inkless, dry printing nanographene via in-Situ Coordinated laser ablation and sintering processes

Printing carbon, such as graphene and other carbon structures, for flexible and printed electronics currently relies on either ink-based printing, laser-induced forward transfer (LIFT), or laser-induced graphitization (LIG) to convert carbon-rich precursor materials, such as polymers, to graphene-like carbon structures. Liquid inks contain toxic solvents, surfactants, and stabilizing additives that degrade electrical conductivity and require high-temperature post-processing. On the other hand, LIG is limited by the substrate. Here, this study introduces an additive manufacturing method for dry-printing carbon nanomaterials, ranging from amorphous carbon to crystalline graphene-like structures, on various substrates. The system utilizes laser ablation of a solid graphite target to create pure carbon nanoparticles in situ and on demand. An inert gas carries the nanoparticles onto the substrate, where they can be deposited either as amorphous structures or laser-sintered in real time to form various graphitic structures. The study of laser processing parameters, specifically fluence and pulse repetition frequency, revealed three unique regimes of nanostructure evolution that influence the morphological and electrical properties of these printed structures. Raman spectroscopy confirmed graphitization with a resistivity slightly higher than that of the bulk graphite target. The conductivity/resistivity could be tuned as a function of sintering laser power. Scanning transmission electron microscopy (STEM) revealed that turbostratic nanographene formed with an interlayer spacing of 0.40 nm. Despite ink-based printing methods, such as screen printing, inkjet printing (IJP), and aerosol jet printing (AJP), this eco-friendly and green manufacturing technique could eliminate toxic chemicals, reduce environmental impact, and enable single-step fabrication of carbon-based devices for applications in wearable sensors, energy storage, flexible electronics, and Internet of Things (IoT) devices.

Additive nanomanufacturing↗

Experimental studies of lithium-based surface chemistry for fusion plasma-facing materials applications

Lithium has enhanced the operational performance of fusion devices such as: TFTR, CDX-U, FTU, T-11 M, and NSTX. Lithium in the solid and liquid state has been studied extensively in laboratory experiments including its erosion and hydrogen-retaining properties. Reductions in physical sputtering up to 40–60% have been measured for deuterated solid and liquid lithium surfaces. Computational modeling indicates that up to a 1:1 deuterium volumetric retention in lithium is possible. This paper presents the results of systematic in situ laboratory experimental studies on the surface chemistry evolution of ATJ graphite under lithium deposition. Results are compared to post-mortem analysis of similar lithium surface coatings on graphite exposed to deuterium discharge plasmas in NSTX. Lithium coatings on plasma-facing components in NSTX have shown substantial reduction of hydrogenic recycling. Questions remain on the role lithium surface chemistry on a graphite substrate has on particle sputtering (physical and chemical) as well as hydrogen isotope recycling. This is particularly due to the lack of in situ measurements of plasma-surface interactions in tokamaks such as NSTX. Results suggest that the lithium bonding state on ATJ graphite is lithium peroxide and with sufficient exposure to ambient air conditions, lithium carbonate is generated. Further, correlation between both results is used to assess the role of lithium chemistry on the state of lithium bonding and implications on hydrogen pumping and lithium sputtering. In addition, reduction of factors between 10 and 30 reduction in physical sputtering from lithiated graphite compared to pure lithium or carbon is also measured.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Electrochemical behavior and separation of iodide in molten LiF-NaF-KF melt

This work studied the electrochemical behavior of iodide in molten LiF-NaF-KF mixture and the separation of iodide from the molten salt at 973 K using a graphite working electrode. The cyclic voltammetry (CV) and chronoamperometry (CA) measurements indicated an anodic passivation layer was formed on the graphite electrode in this melt and the layer blocked the charge transfer across the electrolyte/electrode interface. However, the added I- ions could pass through the passivation layer and were oxidized at the graphite electrode. The characterization of the obtained products proved that iodide ions was efficiently oxidized to I2 gas during electrolysis. Furthermore, the graphite anode showed excellent stability without any obvious change in dimensions after electrolysis, which showed the high current efficiency of I2 evolution reaction. Thus, the graphite electrode was possible to be served as an excellent anode to separate other anions (such as Br) from molten fluoride salts.

36 MATERIALS SCIENCE↗

Enhancing isotope mixing in U-10Mo downblend castings with electromagnetic stirring

Uranium alloyed with 10 wt percent molybdenum (U-10Mo) is the proposed fuel for use in the United States’ high-performance research reactors. The U-10Mo fuel is fabricated by a two-step casting process that downblends highly enriched uranium with depleted uranium (DU) and/or natural uranium (NU) and subsequently alloys the resulting high-assay low-enriched uranium (HALEU) with Mo. Currently, a two-step casting process is needed to meet the ingots’ U-235 enrichment homogeneity specifications. This work demonstrates the ability to provide more homogeneous U-235 distributions during downblend casting by using zirconia for crucibles rather than graphite. When graphite is used as a crucible, the electromagnetic field produced by the induction heater couples directly with the graphite. Zirconia is nonconducting in this study, and therefore does not couple with the field. The induction field couples directly with the metal, and causes electromagnetic stirring (EMS) in the molten metal pool. Eight downblend casting experiments were carried out in this work. Four were performed with zirconia crucibles and four with graphite crucibles. The U-235 enrichment was measured at nine discrete points in each casting using laser ablation multi-collector inductively coupled mass spectrometry (LA-MC-ICP-MS). The enrichment homogeneity was approximately eight times better in zirconia crucible castings than in graphite crucible castings as measured by the plate enrichment range and enrichment coefficient of variation. The results show a single casting step could be used to meet USHPRR enrichment specifications if electromagnetic stirring is present during casting. A related investigation was carried out to determine whether it is appropriate to measure enrichment on as-cast ingots or whether heat treated specimens should be used to accurately characterize enrichment. The results show that the as-cast microstructure plays a significant role in enrichment homogeneity. It is recommended that all enrichment measurements be done after the homogenization heat treatment typical of U-10Mo processing.

36 MATERIALS SCIENCE↗

Reversible hydrogen storage in multilayer graphane: Lattice dynamics, compressibility, and heat capacity studies

Multilayer graphane (hydride of graphite) is a crystalline hydrocarbon of composition CH, which can be synthesized from graphite and molecular hydrogen at pressures above 2GPa [V.E. Antonov et al. Carbon 100 (2016) 465]. Using X-ray diffraction, this compound was tentatively identified as the “graphane II” phase of 3D-graphane predicted by ab initio calculations [X.-D. Wen et al. PNAS 108 (2011) 6833] and consisting of layers of 2D-graphane in the “chair” conformation. When heated in a vacuum, the compound does not form any intermediate hydrocarbons and reversibly decomposes back into graphite and hydrogen at 770–920 K. In the present work, almost single-phase samples of graphite hydride and deuteride were synthesized at 7.4 GPa and 870 K. Their investigation by inelastic neutron scattering supplemented by ab initio calculations gave spectra g(E) of the phonon density of states with a gap of about 15 meV at approx. 100 meV, which is a unique identifier for the chair form of graphane. The equation of state V(P) of the hydride was studied at room temperature and hydrogen pressures up to 53 GPa by synchrotron X-ray diffraction in a diamond anvil cell. Further, the graphane II phase did not react with the surrounding hydrogen and did not undergo any phase transformations upon the compression and after heating to 1500 K at 53GPa. The high thermal and pressure stability of this exotic phase makes it an important part of the C–H system. The obtained g(E) spectra of graphite hydride and deuteride were used to calculate temperature dependences of their heat capacity. Measurements of the heat capacity at temperatures 120–673 K confirmed the good accuracy of these calculations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Superior long-term cycling of high-voltage lithium-ion batteries enabled by single-solvent electrolyte

A new single-solvent electrolyte system comprising lithium bis(fluorosuflonyl) imide (LiFSI) and beta-fluorinated sulfone (TFPMS) was designed to enable very stable long-term cycling of high-voltage lithium-ion batteries. Compared to other fluorinated solvents such as alpha-fluorinated sulfone (FMES) and fluorinated carbonate (FEMC), which are prone to reduction on the graphite anode, the LiFSI-TFPMS system displayed outstanding compatibility with graphite. While regular carbonate and sulfone from the LiFSI electrolyte system are compatible with the graphite anode, their high solvating power not only induces severe corrosion on the aluminum cathode current collector at high voltage, but also renders a low aggregation level at a normal salt concentration (about 1.0 M), resulting in the formation of an unstable solid-electrolyte interphase (SEI) on the graphite anode. Owing to the low solvating power of TFPMS, the aggregation level of the LiFSI-TFPMS system is relatively high even at normal salt concentration, which not only facilitates the formation of a robust SEI by the sacrificial decomposition of LiFSI, but also suppresses the aluminum corrosion of the LiFSI electrolyte system at high voltage. Together with the high intrinsic anodic stability of TFPMS, the superior cycling performance of graphite parallel to LiNi 0.6 Co 0.2 Mn 0.2 O 2 cells was achieved by employing the non-flammable LiFSI-TFPMS single-solvent electrolyte system.

25 ENERGY STORAGE↗

Minimizing Polysulfide Shuttle Effect in Lithium-Ion Sulfur Batteries by Anode Surface Passivation

Lithium-ion sulfur batteries use non-metal materials as the anode to address safety concerns associated with lithium metal anode. However, polysulfide shuttle reactions still occur on the non-metal anode (such as graphite and Si), and result in limited battery efficiency. In this work, we used Al2O3 layers coated by atomic layer deposition (ALD) technique to suppress the shuttle reactions. With the optimal thickness of 2 nm Al2O3 coated on graphite anode, the Coulombic efficiency of the sulfur cathode was improved from 84% to 96% in the first cycle, and from 94% to 97% in the subsequent cycles. As a result, the discharge capacity of the sulfur cathode was increased to 550 mAh g-1 in the 100th cycle, as compared with 440 mAh g-1 when the pristine graphite anode was used. The Al2O3 passivation layer minimizes the formation of insoluble polysulfide (Li2S2, Li2S) on the surface of graphite anode and improves the efficiency and capacity retention of the graphite-sulfur batteries. The surface passivation strategy could also be used in other Li sulfur battery systems (with Li, Si, and Sn anodes), to minimize side reactions and enable high-performance and safe sulfur batteries.

Liu, Jian↗

Nitrogen-Doped Graphene Oxide Electrocatalysts for the Oxygen Reduction Reaction

Platinum group metal-free (PGM-free) electrocatalysts for the oxygen reduction reaction (ORR) often exhibit a complex functionalized graphitic structure. Because of this complex structure, limited understanding exists about the design factors for the synthesis of high-performing materials. Graphene, a two-dimensional hexagonal structure of carbon, is amenable to structural and functional group modifications, making it an ideal analogue to study crucial properties of more complex graphitic materials utilized as electrocatalysts. In this paper, we report the synthesis of active nitrogen-doped graphene oxide catalysts for the ORR in which their activity and four-electron selectivity are enhanced using simple solvent and electrochemical treatments. The solvents, chosen based on Hansen’s solubility parameters, drive a substantial change in the morphology of the functionalized graphene materials by (i) forming microporous holes in the graphitic sheets that lead to edge defects and (ii) inducing 3D structure in the graphitic sheets that promotes ORR. Additionally, the cycling of these catalysts has highlighted the multiplicity of the active sites, with different durability, leading to a highly selective catalyst over time, with a minimal loss in performance. High ORR activity was demonstrated in an alkaline electrolyte with an onset potential of ~1.1 V and half-wave potential of 0.84 V vs RHE. Furthermore, long-term stability potential cycling showed minimal loss in half-wave potential (<3%) in both N 2 - and O 2 -saturated solutions with improved selectivity toward the four-electron reduction after 10000 cycles. Lastly, the results described in this work provide additional understanding about graphitic electrocatalysts in alkaline media that may be utilized to further enhance the performance of PGM-free ORR electrocatalysts.

36 MATERIALS SCIENCE↗

Graphene Nanocomposites with High Molecular Weight Poly(ε-caprolactone) Grafts: Controlled Synthesis and Accelerated Crystallization

Grafting of high molecular weight polymers to graphitic nanoplatelets is a critical step toward the development of high performance graphene nanocomposites. However, designing such a grafting route has remained a major impediment. Herein, we report a "grafting to" synthetic pathway by which high molecular weight polymer, poly(e-caprolactone) (PCL), is tethered, at high grafting density, to highly anisotropic graphitic nanoplatelets. The efficacy of this tethering route and the resultant structural arrangements within the composite are confirmed by neutron and X-ray scattering measurements in the melt and solution phase. In the semicrystalline state, Xray analysis indicates that chain tethering onto the graphitic nanoplatelets results in conformational changes of the polymer chains, which enhance the nucleation process and aid formation of PCL crystallites. This is corroborated by the superior thermal properties of the composite, manifested in accelerated crystallization kinetics and a significant increase in the thermal degradation temperature. Lastly, in principle, this synthesis route can be extended to a variety of high molecular weight polymers, which can open new avenues to solution-based processing of graphitic nanomaterials and the fabrication of complex 3D patterned graphitic nanocomposites.

36 MATERIALS SCIENCE↗

High Yield Synthesis of Mesoscopic Conductive and Dispersible Carbon Nanostructures via Ultrasonication of Commercial Precursors

The need to produce large quantities of graphenic materials displaying excellent conductivity, thermal resistance, and tunable properties for industrial applications has spurred interest in new techniques for exfoliating graphite. In this paper, sonication-assisted exfoliation of graphitic precursors in the presence of chloroform is shown to produce chemically and structurally unique exfoliated graphitic materials in high yields. These exfoliated graphites, referred to as mesographite and mesographene, respectively, exhibit unique properties which depend on the number of layers and exfoliation conditions. Structural characterization of mesographene reveals the presence of nanoscale two-dimensional graphene layers, and threedimensional carbon nanostructures sandwiched between layers, similar to those found in ball-milled and intercalated graphites. The conductivities of mesographite and mesographene are 2700 and 2000 S/m, respectively, indicating high conductivity despite flake damage. Optical absorption measurements of mesographite sonicated in various solvents showed significant changes in dispersion characteristics, and also indicated significant changes to mesoscopic colloidal behavior. A mechanism for functionalization and formation of capped carbon nanostructures is proposed by integrating the chemical and structural characterization in relation to the various carbon structures observed by electron microscopy. Composites based on common polymers were prepared by solution processing, and changes in thermal properties indicate improved dispersion of mesographite in polar polymers.

Srivastava, Vikram K↗

Proton-Coupled Electron Transfer Mechanisms for CO 2 Reduction to Methanol Catalyzed by Surface-Immobilized Cobalt Phthalocyanine

Immobilized cobalt phthalocyanine (CoPc) is a highly promising architecture for the six-proton, six-electron reduction of CO 2 to methanol. This electroreduction process relies on proton-coupled electron transfer (PCET) reactions that can occur by sequential or concerted mechanisms. Immobilization on a conductive support such as carbon nanotubes or graphitic flakes can fundamentally alter the PCET mechanisms. We use density functional theory (DFT) calculations of CoPc adsorbed on an explicit graphitic surface model to investigate intermediates in the electroreduction of CO 2 to methanol. Our calculations show that the alignment of the CoPc and graphitic electronic states influences the reductive chemistry. These calculations also distinguish between charging the graphitic surface and reducing the CoPc and adsorbed intermediates as electrons are added to the system. This analysis allows us to identify the chemical transformations that are likely to be concerted PCET, defined for these systems as the mechanism in which protonation of a CO 2 reduction intermediate is accompanied by electron abstraction from the graphitic surface to the adsorbate without thermodynamically stable intermediates. Furthermore, this work establishes a mechanistic pathway for methanol production that is consistent with experimental observations and provides fundamental insight into how immobilization of the CoPc impacts its CO 2 reduction chemistry.

Adsorption↗

Development of a ReaxFF potential for carbon condensed phases and its application to the thermal fragmentation of a large fullerene

In this paper, we report the development of a ReaxFF reactive potential that can accurately describe the chemistry and dynamics of carbon condensed phases. Density functional theory (DFT)-based calculations were performed to obtain the equation of state for graphite and diamond and the formation energies of defects in graphene and amorphous phases from fullerenes. The DFT data were used to reparametrize ReaxFF CHO , resulting in a new potential called ReaxFF C-2013 . ReaxFF C-2013 accurately predicts the atomization energy of graphite and closely reproduces the DFT-based energy difference between graphite and diamond, and the barrier for transition from graphite to diamond. ReaxFF C-2013 also accurately predicts the DFT-based energy barrier for Stone–Wales transformation in a C 60 (I h ) fullerene through the concerted rotation of a C 2 unit. Later, MD simulations of a C 180 fullerene using ReaxFF C-2013 suggested that the thermal fragmentation of these giant fullerenes is an exponential function of time. An Arrhenius-type equation was fit to the decay rate, giving an activation energy of 7.66 eV for the loss of carbon atoms from the fullerene. Although the decay of the molecule occurs primarily via the loss of C 2 units, we observed that, with an increase in temperature, the probability of loss of larger fragments increases. Finally, the ReaxFF C-2013 potential developed in this work, and the results obtained on fullerene fragmentation, provide an important step toward the full computational chemical modeling of coal pyrolysis, soot incandescence, high temperature erosion of graphitic rocket nozzles, and ablation of carbon-based spacecraft materials during atmospheric reentry.

36 MATERIALS SCIENCE↗

Cylindricity Sensitivity Thermal Model of the AGR-5/6/7 Experiment in the Advanced Test Reactor

The AGR-5/6/7 experiment is currently being irradiated in the Advanced Test Reactor (ATR) at the Idaho National Laboratory and is approximately 70% complete. Several fuel and material irradiation experiments have been planned for the U.S. Department of Energy Advanced Gas Reactor Fuel Development and Qualification Program, which supports the development and qualification of tristructural isotropic (TRISO) coated particle fuel for use in high-temperature gas-cooled reactors. The goals of these experiments are to provide irradiation performance data to support fuel process development, qualify fuel for normal operating conditions, support development of fuel performance models and codes, and provide irradiated fuel and materials for post-irradiation examination and safety testing. Originally planned and named as separate fuel experiments, but subsequently combined into a single test train, AGR-5/6/7 is testing low-enriched uranium oxycarbide TRISO fuel. The AGR-5/6/7 test train has 5 capsules with thermocouples and independent gas control mixtures. Unique to this paper is a sensitivity study concerning the cylindricity of the graphite holders containing the fuel compacts and their eccentricity in relation to the stainless-steel capsule walls. Each capsule has small nubs on the outside used for centering the graphite holder inside the stainless-steel capsule with a small gas gap used to control temperature. Due to machining tolerances of these nubs and vibration wearing the nubs down when the experiment is running in the reactor, the possibility exists that the holder may move around radially. Each capsule is equipped with several thermocouples placed at various radii and depths within each graphite holder. This paper will show the sensitivity of offsetting the graphite holder for various radii in 45-degree increments around the circle with the objective of minimizing the difference between the measured thermocouples and the modeled thermocouple temperatures. Separate gas mixtures of helium/neon are introduced into this gas gap between the holder and capsule wall and changed as necessary to maintain the desired thermocouple temperatures to keep the fuel compacts at constant temperature as the nuclear reactor conditions change. The goal of the sensitivity study is to find a radius and an angle to offset the holder from perfectly centered for each of the five capsules separately. The complex thermal model includes fission heating, gamma heating, radiation heat transfer, and heat transfer via conduction and radiation across the control gaps. Subroutines linked to the thermal model offer an easy method to offset the graphite holder from the capsule walls without remeshing the entire model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗