Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Generative Design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,639 records · Page 91

Automatic blocking for complex three-dimensional configurations

A new blocking technique for complex three-dimensional configurations is described. This new technique is based upon the concept of an abstraction, or squared-up representation, of the configuration and the associated grid. By allowing the user to describe blocking requirements in natural terms (such as 'wrap a grid around this leading edge' or 'make all grid lines emanating from this wall orthogonal to it'), users can quickly generate complex grids around complex configurations, while still maintaining a high level of control where desired. An added advantage of the abstraction concept is that once a blocking is defined for a class of configurations, it can be automatically applied to other configurations of the same class, making the new technique particularly well suited for the parametric variations which typically occur during design processes. Grids have been generated for a variety of real-world, two- and three-dimensional configurations. In all cases, the time required to generate the grid, given just an electronic form of the configuration, was at most a few days. Hence with this new technique, the generation of a block-structured grid is only slightly more expensive than the generation of an unstructured grid for the same configuration.

Dannenhoffer, John F., III↗

Shuttle relative navigation of a tethered satellite mission with current on board software

A Shuttle mission planned in 1991 will test the feasibility of tethers in space. This mission, a joint effort between Italy and the United States, will connect a satellite (built by the Italians) to the Shuttle with a 20 km long tether. This mission poses unique navigation problems. The flight software on the Shuttle was never designed to account for the low level acceleration that is generated by the gravity gradient. IMUs on the Shuttle was never designed to account for the low level acceleration that is generated by the gravity gradient. Inertial Maneuvering Units on the shuttle will sense the acceleration of the tether but it turns out that incorporating the continuous accelerometer noise also generates large error growth. Relative navigation is another important issue since the majority of the mission will be conducted while the satellite is out of the visual range of the crew. Some kind of feedback on the motion of the satellite will be desirable. Feedback of the satellite motion can be generated by using the rendezvous radar. To process the radar measurements, the flight software uses a 13 state Kalman Filter, but unfortunately with the filter currently tuned as it is, valid measurements tend to be ignored. This is due to the constraint of the tether on the satellite, which is an unmodeled force. Analysis shows that with proper tuning, relative navigation is possible.

Lee, Kevin A.↗

ASRM - Turning in a solid performance

The Advanced Solid Rocket Motor (ASRM), currently in its design and development phase, will become the higher reliability/performance next-generation booster for the Space Shuttle. The ASRM design improves safety through the elimination of 229 potential leak paths, thereby eliminating a total of 312 causes of failure. The ASRM will also allow an additional 12,000 lb of payload to be carried by the Shuttle Orbiter. Construction of the ASRM will promote competition through the use of a government owned/contractor operated manufacturing facility. Continuous-mix propellant grain manufacture will be used to enhance safety, quality, and efficiency.

Mitchell, Royce↗

Sub-mm Scale Fiber Guided Deep/Vacuum Ultra-Violet Optical Source for Trapped Mercury Ion Clocks

We demonstrate the functionality of a mercury capillary lamp with a diameter in the sub-mm range and deep ultraviolet (DUV)/ vacuum ultraviolet (VUV) radiation delivery via an optical fiber integrated with the capillary. DUV spectrum control is observed by varying the fabrication parameters such as buffer gas type and pressure, capillary diameter, electrical resonator design, and temperature. We also show spectroscopic data of the 199Hg+ hyper-fine transition at 40.5GHz when applying the above fiber optical design. We present efforts toward micro-plasma generation in hollow-core photonic crystal fiber with related optical design and theoretical estimations. This new approach towards a more practical DUV optical interface could benefit trapped ion clock developments for future ultra-stable frequency reference and time-keeping applications.

lamps↗

Augmenting Parametric Optimal Ascent Trajectory Modeling with Graph Theory

It has been well documented that decisions made in the early stages of Conceptual and Pre-Conceptual design commit up to 80% of total Life-Cycle Cost (LCC) while engineers know the least about the product they are designing [1]. Once within Preliminary and Detailed design however, making changes to the design becomes far more difficult to enact in both cost and schedule. Primarily this has been due to a lack of detailed data usually uncovered later during the Preliminary and Detailed design phases. In our current budget-constrained environment, making decisions within Conceptual and Pre-Conceptual design which minimize LCC while meeting requirements is paramount to a program's success. Within the arena of launch vehicle design, optimizing the ascent trajectory is critical for minimizing the costs present within such concerns as propellant, aerodynamic, aeroheating, and acceleration loads while meeting requirements such as payload delivered to a desired orbit. In order to optimize the vehicle design its constraints and requirements must be known, however as the design cycle proceeds it is all but inevitable that the conditions will change. Upon that change, the previously optimized trajectory may no longer be optimal, or meet design requirements. The current paradigm for adjusting to these updates is generating point solutions for every change in the design's requirements [2]. This can be a tedious, time-consuming task as changes in virtually any piece of a launch vehicle's design can have a disproportionately large effect on the ascent trajectory, as the solution space of the trajectory optimization problem is both non-linear and multimodal [3]. In addition, an industry standard tool, Program to Optimize Simulated Trajectories (POST), requires an expert analyst to produce simulated trajectories that are feasible and optimal [4]. In a previous publication the authors presented a method for combatting these challenges [5]. In order to bring more detailed information into Conceptual and Pre-Conceptual design, knowledge of the effects originating from changes to the vehicle must be calculated. In order to do this, a model capable of quantitatively describing any vehicle within the entire design space under consideration must be constructed. This model must be based upon analysis of acceptable fidelity, which in this work comes from POST. Design space interrogation can be achieved with surrogate modeling, a parametric, polynomial equation representing a tool. A surrogate model must be informed by data from the tool with enough points to represent the solution space for the chosen number of variables with an acceptable level of error. Therefore, Design Of Experiments (DOE) is used to select points within the design space to maximize information gained on the design space while minimizing number of data points required. To represent a design space with a non-trivial number of variable parameters the number of points required still represent an amount of work which would take an inordinate amount of time via the current paradigm of manual analysis, and so an automated method was developed. The best practices of expert trajectory analysts working within NASA Marshall's Advanced Concepts Office (ACO) were implemented within a tool called multiPOST. These practices include how to use the output data from a previous run of POST to inform the next, determining whether a trajectory solution is feasible from a real-world perspective, and how to handle program execution errors. The tool was then augmented with multiprocessing capability to enable analysis on multiple trajectories simultaneously, allowing throughput to scale with available computational resources. In this update to the previous work the authors discuss issues with the method and solutions.

Patrick D Dees↗

CMOS bulk-metal design handbook

User's guide describes techniques for generating precision mask artwork for complex CMOS integrated circuits, starting from logic diagram. Techniques are based on standard-cell approach. Guide also includes user guidelines for designing efficient CMOS arrays.

Edge, T. M.↗

Effect of Engine Thrust and Isp Tradeoffs and Alternate Propellants on ΔV Budget and Architecture Mass for 1st Generation Nuclear Thermal Propulsion Flight Test Systems

Following the first Nuclear Thermal Propulsion (NTP) system test, also known as DRACO, the next NTP system to be developed would be the 1st Generation NTP system. An analysis was conducted to determine the performance of different vehicle configurations utilizing hydrogen (H-NTP), ammonia (A-NTP), and methane (M-NTP) as propellants launched onboard commercial launch vehicles. This was enabled by a quasi-steady-state power balance engine model and vehicle component physics that sized the vehicle system using Master Equipment List (MEL) parameters. The analysis considered configuration cases outlined by a matrix of different mission classes and vehicle configurations that covered the design space of the 1st Generation NTP system to explore various propellant options, engine architectures, and mission scopes. Four mission classes were evaluated which included single burn missions performing maneuvers having a ΔV of 1 km/s and 2.5 km/s followed by 2-burn and 4-burn missions that aimed to exhaust the launch vehicles volume or mass limitations. In all cases, the NTP systems with the lowest thrust class had the longest burn time of which A-NTP and M-NTP systems provided the longest and shortest burn times depending on the launch vehicle used while H-NTP systems tended to cluster together in the middle. Longer burn times could be useful as a testing platform to increase the time for data accumulation. Across the multi-burn cases, H-NTP systems were found to be volume limited while A-NTP and M-NTP systems were mass limited. Both single burn missions showed that A-NTP configurations provided the lowest dry mass given that ammonia had the highest density with comparable performance to M-NTP systems and no requirement for cryocoolers. The results showed that beyond the propellant selection type, the launch vehicle selection, which included Starship, New Glenn, Vulcan, Falcon 9 (recoverable), and Falcon Heavy (recoverable), was a primary driving factor in the test vehicle’s capabilities. Trends were determined based on a set of dimensionless parameters that included the mass ratio of inert mass to initial wetted mass, ratio of specific impulse to burn time, and a dimensionless engine parameter (ratio of impulse to engine momentum). These relationships found the “knees-in-the-curves” that could be a significant point of reference for the designer as they indicate a change in the trend which is located at a specific impulse to burn time ratio of 1, a mass ratio of 0.6, and an engine performance parameter of 4. This study did not attempt to make a recommendation rather provide the tools for the reader to select their own configuration based on their needs.

Propellant↗

Effect of Engine Thrust and Isp Tradeoffs and Alternate Propellants on ΔV Budget and Architecture Mass for 1st Generation Nuclear Thermal Propulsion Flight Test Systems

Following the first Nuclear Thermal Propulsion (NTP) system test, also known as DRACO, the next NTP system to be developed would be the 1st Generation NTP system. An analysis was conducted to determine the performance of different vehicle configurations utilizing hydrogen (H-NTP), ammonia (A-NTP), and methane (M-NTP) as propellants launched onboard commercial launch vehicles. This was enabled by a quasi-steady-state power balance engine model and vehicle component physics that sized the vehicle system using Master Equipment List (MEL) parameters. The analysis considered configuration cases outlined by a matrix of different mission classes and vehicle configurations that covered the design space of the 1st Generation NTP system to explore various propellant options, engine architectures, and mission scopes. Four mission classes were evaluated which included single burn missions performing maneuvers having a ΔV of 1 km/s and 2.5 km/s followed by 2-burn and 4-burn missions that aimed to exhaust the launch vehicles volume or mass limitations. In all cases, the NTP systems with the lowest thrust class had the longest burn time of which A-NTP and M-NTP systems provided the longest and shortest burn times depending on the launch vehicle used while H-NTP systems tended to cluster together in the middle. Longer burn times could be useful as a testing platform to increase the time for data accumulation. Across the multi-burn cases, H-NTP systems were found to be volume limited while A-NTP and M-NTP systems were mass limited. Both single burn missions showed that A-NTP configurations provided the lowest dry mass given that ammonia had the highest density with comparable performance to M-NTP systems and no requirement for cryocoolers. The results showed that beyond the propellant selection type, the launch vehicle selection, which included Starship, New Glenn, Vulcan, Falcon 9 (recoverable), and Falcon Heavy (recoverable), was a primary driving factor in the test vehicle’s capabilities. Trends were determined based on a set of dimensionless parameters that included the mass ratio of inert mass to initial wetted mass, ratio of specific impulse to burn time, and a dimensionless engine parameter (ratio of impulse to engine momentum). These relationships found the “knees-in-the-curves” that could be a significant point of reference for the designer as they indicate a change in the trend which is located at a specific impulse to burn time ratio of 1, a mass ratio of 0.6, and an engine performance parameter of 4. This study did not attempt to make a recommendation rather provide the tools for the reader to select their own configuration based on their needs.

Propellant↗

Effect of Engine Thrust and Isp Tradeoffs and Alternate Propellants on ΔV Budget and Architecture Mass for 1st Generation Nuclear Thermal Propulsion Flight Test Systems

Following the first Nuclear Thermal Propulsion (NTP) system test, also known as DRACO, the next NTP system to be developed would be the 1st Generation NTP system. An analysis was conducted to determine the performance of different vehicle configurations utilizing hydrogen (H-NTP), ammonia (A-NTP), and methane (M-NTP) as propellants launched onboard commercial launch vehicles. This was enabled by a quasi-steady-state power balance engine model and vehicle component physics that sized the vehicle system using Master Equipment List (MEL) parameters. The analysis considered configuration cases outlined by a matrix of different mission classes and vehicle configurations that covered the design space of the 1st Generation NTP system to explore various propellant options, engine architectures, and mission scopes. Four mission classes were evaluated which included single burn missions performing maneuvers having a ΔV of 1 km/s and 2.5 km/s followed by 2-burn and 4-burn missions that aimed to exhaust the launch vehicles volume or mass limitations. In all cases, the NTP systems with the lowest thrust class had the longest burn time of which A-NTP and M-NTP systems provided the longest and shortest burn times depending on the launch vehicle used while H-NTP systems tended to cluster together in the middle. Longer burn times could be useful as a testing platform to increase the time for data accumulation. Across the multi-burn cases, H-NTP systems were found to be volume limited while A-NTP and M-NTP systems were mass limited. Both single burn missions showed that A-NTP configurations provided the lowest dry mass given that ammonia had the highest density with comparable performance to M-NTP systems and no requirement for cryocoolers. The results showed that beyond the propellant selection type, the launch vehicle selection, which included Starship, New Glenn, Vulcan, Falcon 9 (recoverable), and Falcon Heavy (recoverable), was a primary driving factor in the test vehicle’s capabilities. Trends were determined based on a set of dimensionless parameters that included the mass ratio of inert mass to initial wetted mass, ratio of specific impulse to burn time, and a dimensionless engine parameter (ratio of impulse to engine momentum). These relationships found the “knees-in-the-curves” that could be a significant point of reference for the designer as they indicate a change in the trend which is located at a specific impulse to burn time ratio of 1, a mass ratio of 0.6, and an engine performance parameter of 4. This study did not attempt to make a recommendation rather provide the tools for the reader to select their own configuration based on their needs.

Propellant↗

Optimization of a GO2/GH2 Swirl Coaxial Injector Element

An injector optimization methodology, method i, is used to investigate optimal design points for a gaseous oxygen/gaseous hydrogen (GO2/GH2) swirl coaxial injector element. The element is optimized in terms of design variables such as fuel pressure drop, DELTA P(sub f), oxidizer pressure drop, DELTA P(sub 0) combustor length, L(sub comb), and full cone swirl angle, theta, for a given mixture ratio and chamber pressure. Dependent variables such as energy release efficiency, ERE, wall heat flux, Q(sub w) injector heat flux, Q(sub inj), relative combustor weight, W(sub rel), and relative injector cost, C(sub rel), are calculated and then correlated with the design variables. An empirical design methodology is used to generate these responses for 180 combinations of input variables. Method i is then used to generate response surfaces for each dependent variable. Desirability functions based on dependent variable constraints are created and used to facilitate development of composite response surfaces representing some, or all, of the five dependent variables in terms of the input variables. Two examples illustrating the utility and flexibility of method i are discussed in detail. First, joint response surfaces are constructed by sequentially adding dependent variables. Optimum designs are identified after addition of each variable and the effect each variable has on the design is shown. This stepwise demonstration also highlights the importance of including variables such as weight and cost early in the design process. Secondly, using the composite response surface that includes all five dependent variables, unequal weights are assigned to emphasize certain variables relative to others. Here, method i is used to enable objective trade studies on design issues such as component life and thrust to weight ratio.

Tucker, P. Kevin↗

Optimization of a GO2/GH2 Impinging Injector Element

An injector optimization methodology, method i, is used to investigate optimal design points for a gaseous oxygen/gaseous hydrogen (GO2/GH2) impinging injector element. The unlike impinging element, a fuel-oxidizer- fuel (F-O-F) triplet, is optimized in terms of design variables such as fuel pressure drop, (Delta)P(sub f), oxidizer pressure drop, (Delta)P(sub o), combustor length, L(sub comb), and impingement half-angle, alpha, for a given mixture ratio and chamber pressure. Dependent variables such as energy release efficiency, ERE, wall heat flux, Q(sub w), injector heat flux, Q(sub inj), relative combustor weight, W(sub rel), and relative injector cost, C(sub rel), are calculated and then correlated with the design variables. An empirical design methodology is used to generate these responses for 163 combinations of input variables. Method i is then used to generate response surfaces for each dependent variable. Desirability functions based on dependent variable constraints are created and used to facilitate development of composite response surfaces representing some, or all, of the five dependent variables in terms of the input variables. Three examples illustrating the utility and flexibility of method i are discussed in detail. First, joint response surfaces are constructed by sequentially adding dependent variables. Optimum designs are identified after addition of each variable and the effect each variable has on the design is shown. This stepwise demonstration also highlights the importance of including variables such as weight and cost early in the design process. Secondly, using the composite response surface which includes all five dependent variables, unequal weights are assigned to emphasize certain variables relative to others. Here, method i is used to enable objective trade studies on design issues such as component life and thrust to weight ratio. Finally, specific variable weights are further increased to illustrate the high marginal cost of realizing the last increment of injector performance and thruster weight.

Tucker, P. Kevin↗

TPS Materials and Costs for Future Reusable Launch Vehicles

There is considerable interest in developing new reusable launch vehicles (RLVs) for reducing the cost of transporting payload to and from orbit. This work reviews thirteen candidate thermal protection system (TPS) options currently available for RLVs. It is useful to begin with the current Shuttle TPS layout as a reference. The nose cap and wing leading edge , which reach the highest temperatures, are made of reinforced carbon-carbon (RCC) that is protected from oxidation by an external coating (about 0.020" thick) of silicon-carbide. Most of the windward surface is 9 lb/cubic ft ceramic tiles (LI-900) with a thin (about 0.012") coating of Reaction Cured Glass (RCG). The leeward side of the vehicle is covered largely by AFRSI, a quilted ceramic blanket, and FRSI, a polyamide felt. These four materials can be considered first generation reusable TPS. Since the time of the Shuttle design, considerable progress has been made advancing TPS technologies in terms of thermal performance, robustness, and cost. For each of the major systems, a second generation ceramic TPS has been developed, tested, and characterized. Metallic-based systems have also been developed. For applications requiring RCC in the past, advanced carbon-carbon (ACC) is now available. This material has better mechanical properties, somewhat higher temperature capability to 2900F and greatly increased oxidation resistance. New carbon fiber reinforced silicon-carbide matrix composites (C/SiCs) have shown additional improvement in properties over ACC with use temperatures to 3000F and above. For rigid tiles, NASA Ames has made two significant advancements. The first is a tile substrate called Alumina Enhanced Thermal Barrier, or AETB, that incorporates alumina fibers for improved dimensional stability at high temperatures, to 2600F and above. This material can be made to densities as low as 8 lb/cubic ft. The second is a coating preparation called Toughened Uni-piece Fibrous Insulation, or TUFT, that penetrates about 0.1 in. into the tile substrate. The resulting composite, with a functionally gradient density near the surface, provides orders of magnitude increased damage resistance compared with RCG coated LI-900, with only a small weight increase. The TPS that combines these two developments is called AETB-8/TUFI and has been adopted for high damage areas on the Shuttles. Two notable developments have occur-red in flexible ceramic blanket technology. The first is aluminoborosilicate-based fibers with use temperatures of 2200F and above," in comparison to quartz and silica fiber used in AFRSI which have multi-use temperature limits of 1200 to 1400F. Blankets incorporating these new high temperature fibers are referred to as AFRSI-HT. The second is an integral weaving techniques that produces a fluted core blanket with a smoother surface and greater resistance to aero-acoustic noise, to levels as high as 170 dB. This Ames innovation is called Tailorable Advanced Blanket Insulation, or TABI. Finally, for felt-based TPS, Boeing is developing Polybenzimidazole Blanket Insulation, or PBI, with a multi-use temperature limit of 1000F and above, in contrast to Shuttle FRSI which has a multi-use temperature limit of about 700F. 1.6 NASA Langley and BF Goodrich (formerly Rohr Corp.) have led the development of metallic-based TPS. This activity uses essentially three approaches: metallic tiles which encase a fibrous ceramic batting in a box fabricated largely from metallic honeycombs, typically Nickel based alloys; metallic honeycomb sheets, made of Nickel-based alloys, incorporating a fibrous back-side insulation encapsulated in a metallic foil bag, providing reduced weight; and metallic multi-wall, which is comprised of dimpled Titanium metal sheets, which are stacked and then diffusion bonded at contact points to form the TPS. The Nickel-based systems can be used up to temperatures of about 1800F, and the Titanium system to about 100F. These thirteen TPS materials have pros and cons to their usage in terms of temperature capability, weight, initial cost, and maintenance. Carbon-carbon and C/SiC systems have the highest temperature capability but are relatively expensive and heavy, requiring significant time, expertise, and costly facilities and tools for design and fabrication. Second generation ceramic tiles are relatively light, durable, simple to fabricate and easy to install; however, waterproofing is a concern. Blankets and felts are light, simple, inexpensive, and easy to install over curved vehicle surfaces, but durability and waterproofing are concerns. Metallics are robust and appear to have eliminated waterproofing, but they tend to be heavy and relatively expensive, requiring costly facilities and tools. If thin metal sheets are used to reduce weights, then issues arise from possible metal fatigue and corrosion caused by thermal cycling, pressure oscillations, and environmental exposure. For application to future RLVs, system analyses show that a significant component of the vehicle life cycle cost is from the TPS; however, it is difficult to quantify and to compare the potential savings of advanced systems without performing full vehicle designs using each of the different options. Because this entails a considerable effort and also tends to submerge TPS cost impacts under unrelated vehicle design assumptions, there is a clear need for a simpler quantitative method to evaluate the cost impact of different TPS options. To this end, this work introduces a TPS life-cycle cost parameter which is easily computed and applicable to generic RLVs.

Rasky, Dan J.↗

Brief History of Agricultural Systems Modeling

Agricultural systems science generates knowledge that allows researchers to consider complex problems or take informed agricultural decisions. The rich history of this science exemplifies the diversity of systems and scales over which they operate and have been studied. Modeling, an essential tool in agricultural systems science, has been accomplished by scientists from a wide range of disciplines, who have contributed concepts and tools over more than six decades. As agricultural scientists now consider the next generation models, data, and knowledge products needed to meet the increasingly complex systems problems faced by society, it is important to take stock of this history and its lessons to ensure that we avoid re-invention and strive to consider all dimensions of associated challenges. To this end, we summarize here the history of agricultural systems modeling and identify lessons learned that can help guide the design and development of next generation of agricultural system tools and methods. A number of past events combined with overall technological progress in other fields have strongly contributed to the evolution of agricultural system modeling, including development of process-based bio-physical models of crops and livestock, statistical models based on historical observations, and economic optimization and simulation models at household and regional to global scales. Characteristics of agricultural systems models have varied widely depending on the systems involved, their scales, and the wide range of purposes that motivated their development and use by researchers in different disciplines. Recent trends in broader collaboration across institutions, across disciplines, and between the public and private sectors suggest that the stage is set for the major advances in agricultural systems science that are needed for the next generation of models, databases, knowledge products and decision support systems. The lessons from history should be considered to help avoid roadblocks and pitfalls as the community develops this next generation of agricultural systems models.

agricultural systems↗

Space Tug Docking Study. Volume 1: Executive Summary

Results of a detailed systems analysis of the entire rendezvous and docking operation to be performed by the all-up space tug are presented. Specific areas investigated include: generating of operational requirements and a data base of candidate operational techniques and subsystem mechanizations; selection and ranking of integrated system designs capable of meeting the requirements generated; and definition of this simulation/demonstration program required to select and prove the most effective manual, autonomous, and hybrid rendezvous and docking systems.

Source record↗

Emmons spot forcing for turbulent drag reduction

An Emmons spot-generation wind tunnel system has been designed to trigger closely spaced Emmons spots in the spanwise and longitudinal directions of an aerodynamic surface. For certain combinations of generator frequencies and amplitude, hole size, and hole spacing, experimental results indicate smaller turbulence scales and a reduction in skin friction of about 15 percent.

Goodman, W. L.↗

The aerodynamic characteristics of vortex ingestion for the F/A-18 inlet duct

A Reduced Navier-Stokes (RNS) solution technique was successfully combined with the concept of partitioned geometry and mesh generation to form a very efficient 3D RNS code aimed at the analysis-design engineering environment. Partitioned geometry and mesh generation is a pre-processor to augment existing geometry and grid generation programs which allows the solver to (1) recluster an existing gridlife mesh lattice, and (2) perturb an existing gridfile definition to alter the cross-sectional shape and inlet duct centerline distribution without returning to the external geometry and grid generator. The present results provide a quantitative validation of the initial value space marching 3D RNS procedure and demonstrates accurate predictions of the engine face flow field, with a separation present in the inlet duct as well as when vortex generators are installed to supress flow separation. The present results also demonstrate the ability of the 3D RNS procedure to analyze the flow physics associated with vortex ingestion in general geometry ducts such as the F/A-18 inlet. At the conditions investigated, these interactions are basically inviscid like, i.e., the dominant aerodynamic characteristics have their origin in inviscid flow theory.

Anderson, Bernhard H.↗

Preliminary design of a high speed civil transport: The Opus 0-001

Based on research into the technology and issues surrounding the design, development, and operation of a second generation High Speed Civil Transport, HSCT, the Opus 0-001 team completed the preliminary design of a sixty passenger, three engine aircraft. The design of this aircraft was performed using a computer program which the team wrote. This program automatically computed the geometric, aerodynamic, and performance characteristic of an aircraft whose preliminary geometry was specified. The Opus 0-001 aircraft was designed for a cruise Mach number of 2.2, a range of 4,700 nautical miles and its design was based in current or very near term technology. Its small size was a consequence of an emphasis on a profitable, low cost program, capable of delivering tomorrow's passengers in style and comfort at prices that make it an attractive competitor to both current and future subsonic transport aircraft. Several hundred thousand cases of Cruise Mach number, aircraft size and cost breakdown were investigated to obtain costs and revenues for which profit was calculated. The projected unit flyaway cost was $92.0 million per aircraft.

Source record↗

Optimum Design of Aerospace Structural Components Using Neural Networks

The application of artificial neural networks to capture structural design expertise is demonstrated. The principal advantage of a trained neural network is that it requires a trivial computational effort to produce an acceptable new design. For the class of problems addressed, the development of a conventional expert system would be extremely difficult. In the present effort, a structural optimization code with multiple nonlinear programming algorithms and an artificial neural network code NETS were used. A set of optimum designs for a ring and two aircraft wings for static and dynamic constraints were generated using the optimization codes. The optimum design data were processed to obtain input and output pairs, which were used to develop a trained artificial neural network using the code NETS. Optimum designs for new design conditions were predicted using the trained network. Neural net prediction of optimum designs was found to be satisfactory for the majority of the output design parameters. However, results from the present study indicate that caution must be exercised to ensure that all design variables are within selected error bounds.

Berke, L.↗